Computational And Experimental Comparison Of A Powered Lift, Upper Surface Blowing Configuration, Jay M. Marcos

Master's Theses

In the past, 2D CFD analysis of Circulation Control technology have shown poor comparison with experimental results. In Circulation Control experiments, typical results show a relationship between lift coefficient, CL, vs blowing momentum coefficient, Cμ. CFD analysis tend to over-predict values of CL due to gridding issues and/or turbulence model selection. This thesis attempted to address both issues by performing Richardson’s Extrpolation method to determine an acceptable mesh size and by using FLUENT’s 2-equation turbulence models. The experimental results and CAD geometry were obtained from Georgia Tech Research Institute for comparison with the CFD analysis.

The study showed that 3D …

Qualitative Methods Used To Develop And Characterize The Circulation Control System On Cal Poly's Amelia, Eric N. Paciano

Master's Theses

The circulation control system onboard Cal Poly's Advanced Model for Extreme Lift and Improved Aeroacoustics was a critical component of a highly complex wind tunnel model produced in order to fulfill the requirements of a NASA Research Announcement awarded to David Marshall of the Aerospace Engineering Department. The model was based on a next generation, 150 passenger, regional, cruise efficient, short take-off and landing concept aircraft that achieved high lift through circulation control wings and over-the-wing mounted engines. The wind tunnel model was 10-ft in span, used turbine propulsion simulators, and had a functioning circulation control system driven from tunnel …

Microphone-Based Pressure Diagnostics For Boundary Layer Transition, Spencer Everett Lillywhite

Master's Theses

An experimental investigation of the use low-cost microphones for unsteady total pressure measurement to detect transition from laminar to turbulent boundary layer flow has been conducted. Two small electret condenser microphones, the Knowles FG-23629 and the FG-23742, were used to measure the pressure fluctuations and considered for possible integration with an autonomous boundary layer measurement system. Procedures to determine the microphones’ maximum sound pressure levels and frequency response using an acoustic source provided by a speaker and a reference microphone. These studies showed that both microphones possess a very flat frequency response and that the max SPL of the FG-23629 …

Design And Performance Of Circulation Control Geometries, Rory Martin Golden

Master's Theses

With the pursuit of more advanced and environmentally-friendly technologies of today’s society, the airline industry has been pushed further to investigate solutions that will reduce airport noise and congestion, cut down on emissions, and improve the overall performance of aircraft. These items directly influence airport size (runway length), flight patterns in the community surrounding the airport, cruise speed, and many other aircraft design considerations which are setting the requirements for next generation aircraft. Leading the research in this movement is NASA, which has set specific goals for the next generation regional airliners and has categorized the designs that meet the …

Distributed Forcing On A 3d Bluff Body With A Blunt Base, An Experimental Active Drag Control Approach, Ethan Bruce Erlhoff

Master's Theses

This paper seeks to explore the effects of an active drag control method known as distributed forcing on a 3D bluff body with a blunt base. The 9.5 x 15.25 x 3 inch aluminum model constructed for this experiment has an elliptically shaped nose and rectangular aft section. The model is fitted with four, 12 Volt fans, forcing the freestream air into and out of 1 mm thick slots on the upper and lower trailing edges. The forcing is steady in time, held at a constant forcing velocity though all Reynolds numbers, but varies roughly sinusoidally in the spanwise direction …

Confined Mixing Of Multiple Transverse Jets, Allen J. Bishop

Master's Theses

The mixing performance of multiple transverse jets has been evaluated experimentally. Measurement techniques included laser Doppler velocimetry and planar laser induced fluorescence. Basic findings are consistent with results presented in literature for single jet mixing behavior. Mixing performance has been compared to literature for the single jet case and the Holdeman parameter has been re-evaluated for effectiveness at low jet numbers. A single jet in a confined crossflow was found to have a local minimum at B(d⁄D) = 0.721. Results for two jets indicate monotonically decreasing unmixedness for the range of conditions tested, with no local optimum apparent. Data for …

Analysis Of A Goldschmied Propulsor Using Computational Fluid Dynamics Referencing California Polytechnic's Goldschmied Propulsor Testing, Cory A. Seubert

Master's Theses

The Goldschmied Propulsor is a concept that was introduced in mid 1950's by Fabio Goldschmied. The concept combines boundary layer suction and boundary layer ingestion technologies to reduce drag and increase propulsor efficiency. The most recent testing, done in 1982, left questions concerning the validity of the results. To answer these questions a 38.5in Goldschmied Propulsor was constructed and tested in Cal Poly's 3x4ft wind tunnel. The focus of their wind tunnel investigation was to replicate Goldschmied's original testing and increase the knowledge base on the subject. The goal of this research was to create a computational fluid dynamics (CFD) …

Hot-Wire Anemometer For The Boundary Layer Data System, William D. Neumeister

Master's Theses

Hot-wire anemometry has been routinely employed for laboratory measurements of turbulence for decades. This thesis presents a hot-wire anemometer suitable for use with the Boundary Layer Data System (BLDS). BLDS provides a unique platform for in- flight measurements because of its small, self-contained, robust design and flexible architecture. Addition of a hot-wire anemometer would provide BLDS with a sensor that could directly measure flow velocity fluctuations caused by turbulence. Hot-wires are commonly operated in constant-temperature mode for high frequency response, but require a carefully tuned bridge. The constant-voltage anemometer (CVA) uses a simple op-amp circuit to improve frequency response over …

Experimental Investigation Of A 2-D Air Augmented Rocket: High Pressure Ratio And Transient Flow-Fields, Josef S. Sanchez

Master's Theses

A 2-D Air Augmented Rocket, the Cal Poly Air Augmented Rocket (CPAAR) Test Apparatus operating as a mixer-ejector was tested to investigate high stagnation pressure ratio and transient flow fields of an ejector. The primary rocket ejector was supplied with high pressure nitrogen at a maximum chamber pressure of 1758 psia and a maximum mass flow rate of 1.4 lb/s. The secondary flow air was entrained from a fixed volume plenum chamber producing pressures as low as 3.3 psia. The maximum total pressure ratio achieved was 221. The original CPAAR apparatus was rebuilt re-instrumented and capability expanded. A fixed volume …

Effect Of End-Plate Tabs On Drag Reduction Of A 3d Bluff Body With A Blunt Base, Jarred Michael Pinn

Master's Theses

This thesis involves the experimental testing of a bluff body with a blunt base to evaluate the effectiveness of end-plate tabs in reducing drag. The bluff body is fitted with interchangeable end plates; one plate is flush with the rest of the exterior and the other plate has small tabs protruding perpendicularly into the flow. The body is tested in the Cal Poly 3ft x 4ft low speed wind tunnel. Testing is conducted in three phases.

The first phase was the hot-wire measurement of streamwise velocity of the near wake behind the bluff body. An IFA300 thermal anemometry system with …

Experimental Investigation Of Suction Slot Geometry On A Goldschmied Propulsor, Nicole M. Thomason

Master's Theses

The Goldschmied Propulsor concept combines boundary layer suction and boundary layer ingestion to improve propulsive efficiency and reduce drag on an axisymmetric body. This investigation of a Goldschmied Propulsor aimed to determine influential characteristics of the suction slot geometry to aid in better slot geometry design and to decrease the suction flow requirements for maintaining attached flow over the entire model surface. The Propulsor model was 38.5 inches in length with a max diameter of 13.5 inches. Three suction slot geometries were investigated with the addition of aluminum cusps to the slot entrance. The cusps varied in the distance they …

Implementation And Validation Of The Ζ-F And Asbm Turbulence Models, Dustin Van Blaricom Quint

Master's Theses

The use of Computational Fluid Dynamics (CFD) tools throughout the engineering industry has become standard. Simulations are used during nearly all steps throughout the life cycle of products including design, production, and testing. Due to their wide range of use, industrial CFD codes are becoming more flexible and easier to use. These commercial codes require robustness, reliability, and efficiency. Consequently, linear eddy viscosity models (LEVM) are used to model turbulence for an increasing number of flow types. LEVM such as k-ε and k-ω provide modeling with little loss of computational efficiency and have proven to be robust. The LEVM that …

Unsteady Total Pressure Measurement For Laminar-To-Turbulent Transition Detection, Akane Sharon Karasawa

Master's Theses

This thesis presents the use of an unsteady total pressure measurement to detect laminar-to-turbulent transition. A miniature dynamic pressure transducer, Kulite model XCS-062-5D, was utilized to measure the total pressure fluctuations, and was integrated with an autonomous boundary layer measurement device that can withstand flight test conditions. Various sensor-probe configurations of the Kulite pressure transducer were first examined in a wind tunnel with a 0.610 m (2.0 ft) square test section with a maximum operational velocity of 49.2 m/s (110 mph), corresponding dynamic pressure of 1.44 kPa (30 psf). The Kulite sensor was placed on an elliptical nose flat plate …

Designing The Human-Powered Helicopter: A New Perspective, Gregory Hamilton Gradwell

Master's Theses

The concept of human-powered vertical flight was studied in great depth. Through the manipulation of preexisting theory and analytical methods, a collection of design tools was created to expediently conceptualize and then analyze virtually any rotor. The tools were then arranged as part of a complete helicopter rotor design process. The lessons learned as a result of studying this process—and the tools of which it consists—are presented in the following discussion. It is the belief of the author that by utilizing these tools, as well as the suggestions that accompany them, future engineers may someday build a human-powered helicopter capable …

A Computational Study Of Engine Deflection Using A Circulation Control Wing, Bryan Holly Blessing

Master's Theses

In the past, research into Short Takeoff and Landing aircraft has led to the investigation of the coupling of a Circulation Control Wing and Upper Surface Blowing engine. The Circulation Control Wing entrains the flow of the engine to be deflected downward such that a component of the thrust is now in the vertical direction. The unfortunate consequence of the Upper Surface Blowing engine is the poor cruise performance due to scrub drag. Cal Poly's research into a Cruise Efficient Short Takeoff and Landing Aircraft offers a solution by pylon mounting over the wing engines. Analysis shows that the engine …

High-Frame-Rate Oil Film Interferometry, Jonathan Charles White

Master's Theses

High-Frame-Rate Oil Film Interferometry

Jonathan Charles White

This thesis presents the design and implementation of a high-frame-rate oil film interferometry technique (HOFI) used to directly measure skin friction in time dependent flows. Experiments were performed to determine the ability of a high-speed camera to capture oil film interferometry images. HOFI was found to be able to capture these interferometry images at frequencies up to 10⁵ Hz. Steady laminar and turbulent flows were tested. Transient flows tested consisted of a wind tunnel ramping up in velocity and a laminar boundary layer which was intermittently tripped to turbulence by puffing air …

An Investigative Study Of Gurney Flaps On A Naca 0036 Airfoil, Gregory F. Altmann

Master's Theses

This project examined the effect of Gurney flaps on a 2D, 2-ft chord NACA 0036 airfoil in the Cal Poly 3’x4’ low speed wind tunnel at 25 m/s.  It also covered the numerical simulation of the experiment in computational fluid dynamics (CFD).  During the study, problems with the wind tunnel data were seen.  After a careful diagnosis, the problem was traced to dirty flow conditioners which were subsequently replaced.

Five Gurney flaps at 1, 2, 3, 4, and 5% of the chord were tested.  The Gurney flaps had the effect of eliminating the lift reversal effect and lowering the profile …

Development Of Measurement Methods For Application To A Wind Tunnel Test Of An Advanced Transport Model, Robert S. Ehrmann

Master's Theses

California Polytechnic State University, San Luis Obispo is currently working towards developing a Computational Fluid Dynamics (CFD) database for future code validation efforts. Cal Poly will complete a wind tunnel test on the Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA) in the National Full-Scale Aerodynamics Complex (NFAC) 40 foot by 80 foot wind tunnel at NASA Ames Research Center in the summer of 2011. The development of two measurement techniques is discussed in this work, both with the objective of making measurements on AMELIA for CFD validation.

First, the work on the application of the Fringe-Imaging Skin Friction …

Implementation Of A Conrad Probe On A Boundary Layer Measurement System, Charles Rocky Ulk

Master's Theses

This thesis presents the design, calibration, and performance evaluation of a type of two-hole pressure probe anemometer known as a Conrad probe, as well as its subsequent implementation on an autonomous, compact boundary layer measurement device and its first application for subsonic in-flight measurements of a swept wing boundary layer. Calibration of the Conrad probe was accomplished using two calibration functions and a non-nulling method for resolving in-plane flow velocity direction and magnitude over a range of ±30 degrees. This approach to calibration and application offered the advantages of rapid data acquisition with lower energy consumption than alternative methods for …

Development Of A Meshless Method To Solve Compressible Potential Flows, Alejandro Ramos

Master's Theses

The utility of computational fluid dynamics (CFD) for solving problems of engineering interest has experienced rapid growth due to the improvements in both memory capacity and processing speed of computers. While the capability now exists for the solution of the Navier-Stokes equations about complex and complete aircraft configurations, the bottleneck within the process is the time consuming task of properly generating a mesh that can accurately solve the governing partial differential equations (PDEs). This thesis explored two numerical techniques that attempt to circumvent the difficulty associated with the meshing process by solving a simplified form of the continuity equation within …

A Three Dimensional Vortex Particle-Panel Code For Modeling Propeller-Airframe Interaction, Jacob S. Calabretta

Master's Theses

Analysis of the aerodynamic effects of a propeller flowfield on bodies downstream of the propeller is a complex task. These interaction effects can have serious repercussions for many aspects of the vehicle, including drag changes resulting in larger power requirements, stability changes resulting in adjustments to stabilizer sizing, and lift changes requiring wing planform adjustments.

Historically it has been difficult to accurately account for these effects at any stage during the design process. More recently methods using Euler solvers have been developed that capture interference effects well, although they don't provide an ideal tool for early stages of aircraft design, …

Numerical Examination Of Flow Field Characteristics And Fabri Choking Of 2d Supersonic Ejectors, Brett G. Morham

Master's Theses

An automated computer simulation of the two-dimensional planar Cal Poly Supersonic Ejector test rig is developed. The purpose of the simulation is to identify the operating conditions which produce the saturated, Fabri choke and Fabri block aerodynamic flow patterns. The effect of primary to secondary stagnation pressure ratio on the efficiency of the ejector operation is measured using the entrainment ratio which is the secondary to primary mass flow ratio.

The primary flow of the ejector is supersonic and the secondary (entrained) stream enters the ejector at various velocities at or below Mach 1. The primary and secondary streams are …

Novel Inverse Airfoil Design Utilizing Parametric Equations, Kevin A. Lane

Master's Theses

The engineering problem of airfoil design has been of great theoretical interest for almost a century and has led to hundreds of papers written and dozens of methods developed over the years. This interest stems from the practical implications of airfoil design. Airfoil selection significantly influences the application's aerodynamic performance. Tailoring an airfoil profile to its specific application can have great performance advantages. This includes considerations of the lift and drag characteristics, pitching moment, volume for fuel and structure, maximum lift coefficient, stall characteristics, as well as off-design performance.

A common way to think about airfoil design is optimization, the …

Assessing The V2-F Turbulence Models For Circulation Control Applications, Travis M. Storm

Master's Theses

In recent years, airports have experienced increasing airport congestion, partially due to the hub-and-spoke model on which airline operations are based. Current airline operations utilize large airports, focusing traffic to a small number of airports. One way to relieve such congestion is to transition to a more accessible and efficient point-to-point operation, which utilizes a large web of smaller airports. This expansion to regional airports propagates the need for next-generation low-noise aircraft with short take-off and landing capabilities. NASA has attacked this problem with a high-lift, low-noise concept dubbed the Cruise Efficient Short Take-Off and Landing (CESTOL) aircraft. The goal …

High Order Finite Elements For Lagrangian Computational Fluid Dynamics, Truman Everett Ellis

Master's Theses

A general finite element method is presented to solve the Euler equations in a Lagrangian reference frame. This FEM framework allows for separate arbitrarily high order representation of kinematic and thermodynamic variables. An accompanying hydrodynamics code written in Matlab is presented as a test-bed to experiment with various basis function choices. A wide range of basis function pairs are postulated and a few choices are developed further, including the bi-quadratic Q2-Q1d and Q2-Q2d elements. These are compared with a corresponding pair of low order bi-linear elements, traditional Q1-Q0 and sub-zonal pressure Q1-Q1d. Several test problems are considered including static convergence …

Aerodynamic Performance Enhancement Of A Naca 66–206 Airfoil Using Supersonic Channel Airfoil Design, David Michael Giles

Master's Theses

Supersonic channel airfoil design techniques have been shown to significantly reduce drag in high-speed flows over diamond shaped airfoils by Ruffin and colleagues. The effect of applying these techniques to a NACA 66-206 airfoil is presented. The design domain entails channel heights of 8-16.6% thickness-to-chord and speeds from Mach 1.5-3.0. Numerical simulations show an increase in the lift-to-drag ratio for airfoils at Mach 2.5 at a 35,000-ft altitude with a 12% channel height geometry showing a benefit of 17.2% at 6-deg angle of attack and a sharp channel leading edge. Wave drag is significantly reduced while viscous forces are slightly …

Rayleigh Flow Of Two-Phase Nitrous Oxide As A Hybrid Rocket Nozzle Coolant, Lauren May Nelson

Master's Theses

The Mechanical Engineering Department at California Polytechnic State University in San Luis Obispo currently maintains a lab-scale hybrid rocket motor for which nitrous oxide is utilized as the oxidizer in the combustion system. Because of its availability, the same two-phase (gas and liquid) nitrous oxide that is used in the combustion system is also routed around the throat of the hybrid rocket’s converging-diverging nozzle as a coolant. While this coolant system has proven effective empirically in previous tests, the physics behind the flow of the two-phase mixture is largely unexplained. This thesis provides a method for predicting some of its …

The Interaction Between Throttling And Thrust Vectoring Of An Annular Aerospike Nozzle, David Michael Imbaratto

Master's Theses

Applied research and testing has been conducted at the Cal Poly San Luis Obispo High-pressure Blow-Down facility to study the affects of throttling in a thrust-vectored aerospike nozzle. This study supports the ongoing research at Cal Poly to effectively thrust vector a hybrid rocket motor. Such thrust vectoring is achieved by small secondary ports in the nozzle body that are perpendicular to the main nozzle. The testing conducted included characterizing and comparing the performance of a straight aerospike nozzle to that of a thrust-vectored aerospike nozzle. Throttling effects on the aerospike nozzle in an unvectored and in a vectored configuration …

Multidisciplinary Design Optimization Of An Extreme Aspect Ratio Hale Uav, Bryan J. Morrisey

Master's Theses

ABSTRACT

Multidisciplinary Design Optimization of an Extreme Aspect Ratio HALE UAV

Bryan J. Morrisey

Development of High Altitude Long Endurance (HALE) aircraft systems is part of a vision for a low cost communications/surveillance capability. Applications of a multi payload aircraft operating for extended periods at stratospheric altitudes span military and civil genres and support battlefield operations, communications, atmospheric or agricultural monitoring, surveillance, and other disciplines that may currently require satellite-based infrastructure. Presently, several development efforts are underway in this field, including a project sponsored by DARPA that aims at producing an aircraft that can sustain flight for multiple years and …

A System For Measuring The Lift And Drag Forces Of A Spinning Golf Ball Held Fixed Within A Wind Tunnel, Ryan R. Miller

Master's Theses

A system was designed, built and tested in order to test the aerodynamic properties of a standard golf ball in a wind tunnel manufactured by ELD, Inc. model 406(B). The system consists of a rotating shaft, on which the golf ball is attached, connected to a two-axis force transducer. Additionally, an automated data acquisition system was built for enhanced precision of measurements. Data for wind speeds up to 160 ft/s and rotational speeds up to 8,600 rpm were obtained and analyzed. The purpose of the designed apparatus was to allow for studies to better understand the lift and drag coefficients …