Aerodynamics and Fluid Mechanics Commons^™

A Study Of The Design Of Adaptive Camber Winglets, Justin J. Rosescu

Master's Theses

A numerical study was conducted to determine the effect of changing the camber of a winglet on the efficiency of a wing in two distinct flight conditions. Camber was altered via a simple plain flap deflection in the winglet, which produced a constant camber change over the winglet span. Hinge points were located at 20%, 50% and 80% of the chord and the trailing edge was deflected between -5° and +5°. Analysis was performed using a combination of three-dimensional vortex lattice method and two-dimensional panel method to obtain aerodynamic forces for the entire wing, based on different winglet camber configurations. …

A Study Of The Utilization Of Panel Method For Low Aspect Ratio Wing Analysis, William Barton D. Newey

Master's Theses

This study demonstrates the applicability of using a modified application strategy of panel method to analyze low aspect ratio wings at preliminary design phases. Conventional panel methods fail to capture the leading edge vortex (LEV) that is shed by wings with low aspect ratios, typically below 2 depending on planform. This aerodynamic phenomenon contributes to a significant amount of the lift of these wings and the result is a drastic underestimation of the lift characteristics when analyzed by conventional panel method. To capture the effect of the leading edge vortex, a panel method code was used with an extended definition …

Conceptual Design Of A South Pole Carrier Pigeon Uav, Kendrick M. Dlima

Master's Theses

Currently, the South Pole has a large data problem. It is estimated that 1.2 TB of data is being produced every day, but less than 500 GB of that data is being uploaded via aging satellites to researchers in other parts of the world. This requires those at the South Pole to analyze the data and carefully select the parts to send, possibly missing out on vital scientific information. The South Pole Carrier Pigeon will look to bridge this data gap.

The Carrier Pigeon will be a small unmanned aerial vehicle that will carry a 30 TB solid-state hard drive …

A Study Of The Standard Cirrus Wing Lift Distribution Versus Bell Shaped Lift Distribution, William H. Bergman

Master's Theses

This thesis discusses a comparison of the differences in aerodynamic performance of wings designed with elliptical and bell-shaped lift distributions. The method uses a Standard Cirrus sailplane wing with a lift distribution associated with the induced drag benefits of an elliptical distribution (span efficiency = 0.96) as the basis of comparison. The Standard Cirrus is a standard class sailplane with 15-meter wingspan that was designed by Schempp-Hirth in 1969. This sailplane wing was modeled and analyzed in XFLR5, then validated against existing wind tunnel airfoil data, and Standard Cirrus flight test data. The root bending moment of the baseline wing …

Lip Thrust Apparatus, Ian M. Wilson, Alvin K. Cheong

Mechanical Engineering

This document contains the background information, defined scope of work, preliminary design philosophy, conceptual design development, and final design choices along with its corresponding manufacturing and design verification plans. It also includes the preliminary testing and prototyping necessary in bringing our verification prototype to its final configuration for delivery. Finally, it includes the entire manufacturing process followed in creating the final project and the extensive testing performed to ensure it meets the defined engineering specifications. The aerodynamic phenomenon being analyzed and demonstrated in our final deliverable can be seen in a scenario where when a propeller is enclosed in a …

Dynamic Pressure Sensing For The Flight Test Data System, Marc Y. Goupil

Master's Theses

This thesis describes the design, assembly, and test of the FTDS-K, a new device in the Boundary Layer Data System (BLDS) family of flight data acquisition systems. The FTDS-K provides high-frequency, high-gain data acquisition capability for up to two pressure sensors and an additional three low-frequency pressure sensors. Development of the FTDS-K was separated into a core module, specialized analog subsystem, and practical testing of the FTDS-K in a flow measurement mission. The core module combines an nRF52840-based microcontroller module, switching regulator, microSD card, real-time clock, temperature sensor, and trio of pressure sensors to provide the same capabilities as previous-generation …

Investigation Of The Under-Body Flow Field Of A Prototype Long-Range Electric Vehicle, Matthew P. Nguyen

Master's Theses

This thesis presents changes to the design of the Prototype Vehicles Laboratory (PROVE Lab) Endurance Car, an electric car intended to break the Guinness World Record for the single-charge range of an electric vehicle. The design range is 1609.34 km, however at the design velocity of 104.6 kph, the drag is 196 N; which requires more battery capacity than the 100 kWh maximum of the baseline model. With a fixed frontal area, drag reduction can come from lowered velocity or reduced CD. CD reduction is attempted in four ways: side skirts between the fenders, a raised ride height, an elongated …

Experimental Investigation Into Utilizing Synthetic Jet Actuators To Suppress Bi-Modal Wake Behavior Behind An Ahmed Body, Daniel Jacob Baratta

Master's Theses

Testing done on the flat-back Ahmed Body and other bluff bodies has shown the existence of a bi-stable reflectional symmetry-breaking wake at Reynolds numbers ranging from 340 to 2.41 x 10⁶. Several methods of flow control, both active and passive, have been used to improve the efficiency of the Ahmed body but their effect on the bi-stable nature of the wake has not been investigated. This work details the experimental investigation done to determine if piezoelectrically driven synthetic jet actuators are capable of suppressing the bi-stable wake effects observed behind the Ahmed Body. The synthetic jets were designed …

A Homegrown Dsmc-Pic Model For Electric Propulsion, Dominic Charles Lunde

Master's Theses

Powering spacecraft with electric propulsion is becoming more common, especially in CubeSat-class satellites. On account of the risk of spacecraft interactions, it is important to have robust analysis and modeling tools of electric propulsion engines, particularly of the plasma plume. The Navier-Stokes equations used in classic continuum computational fluid dynamics do not apply to the rarefied plasma, and therefore another method must be used to model the flow. A good solution is to use the DSMC method, which uses a combination of particle modeling and statistical methods for modeling the simulated molecules. A DSMC simulation known as SINATRA has been …

Sweep And Taper Analysis Of Surfboard Fins Using Computational Fluid Dynamics, Brandon James Baldovin

Master's Theses

The research presented here provides a basis for understanding the hydrodynamics of surfboard fin geometries. While there have been select studies on fins there has been little correlation to the shape of the fin and its corresponding hydrodynamic performance. This research analyzes how changing the planform shape of a surfboard fin effects its performance and flow field. This was done by isolating the taper and sweep distribution of a baseline geometry and varying each parameter individually whilst maintaining a constant span and surface area. The baseline surfboard fin was used as a template in Matlab to generate a set of …

A Higher-Order Method Implemented In An Unstructured Panel Code To Model Linearized Supersonic Flows, Jake Daniel Davis

Master's Theses

Since their conception in the 1960s, panel codes have remained a critical tool in the design and development of air vehicles. With continued advancement in computational technologies, today's codes are able to solve flow fields around arbitrary bodies more quickly and with higher fidelity than those that preceded them. Panel codes prove most useful during the conceptual design phase of an air vehicle, allowing engineers to iterate designs, and generate full solutions of the flow field around a vehicle in a matter of seconds to minutes instead of hours to days using traditional CFD methods. There have been relatively few …

Investigating The Effect Of An Upstream Spheroid On Tandem Hydrofoils, Joel Tynan Guerra

Master's Theses

This thesis documents a series of three dimensional unsteady Reynolds Averaged Navier-Stokes CFD simulations used to investigate the influence of an upstream prolate spheroid body on tandem pitching hydrofoils. The model is validated by performing separate CFD simulations on the body and pitching hydrofoils and comparing results to existing experimental data. The simulations were run for a range of Strouhal numbers (0.2-0.5) and phase differences (0-π). Results were compared to identical simulations without an upstream body to determine how the body affects thrust generation and the unsteady flow field.

The combined time-averaged thrust increases with Strouhal number, and is highest …

A Computational Fluid Dynamics (Cfd) Analysis Of The Aerodynamic Effects Of The Seams On A Two-Dimensional Representation Of A Soccer Ball, Allen R. Rohr

Master's Theses

Most major sports today use a dedicated ball or projectile with specific shape, size, and surface geometry, except for soccer. Over the history of the sport, the surface geometry and design stayed relatively unchanged, sewn together using 32 pentagonal and hexagonal panels. However, recent innovations in panel designs differ substantially from the traditional 32 panel ball. The effects these new designs have on the aerodynamic characteristics of the ball have remained largely unknown, even with the influx of experimental research completed in the past decade. Experimental studies have been broad in scope, analyzing an entire ball in wind tunnels or …

Bi-Stability In The Wakes Of Platooning Ahmed Bodies, Daniel M. Stalters

Master's Theses

Autonomous heavy vehicles will enable the promise of decreased energy consumption through the ability to platoon in closer formation than is currently safe or legal. It is therefore increasingly important to understand the complex and dynamic wake interactions between vehicles operating in close proximity for aerodynamic gains. In recent years, a growing body of research has documented a bi-stable, shifting wake generated behind the Ahmed reference bluff body. At the same time, studies of platooning Ahmed bodies have focused on changes to the body forces and moments at different following distances or lateral offsets, typically based around time-averaged measurements or …

The Development And Validation Of Sinatra: A Three-Dimensional Direct Simulation Monte Carlo (Dsmc) Code Written In Object-Oriented C++ And Performed On Cartesian Grids, David Matthew Galvez

Master's Theses

The field of Computational Fluid Dynamics (CFD) primarily involves the approximation of the Navier-Stokes equations. However, these equations are only valid when the flow is considered continuous such that molecular interactions are abundant and predictable. The Knudsen number, $Kn$, which is defined as the ratio of the flow's mean free path, $\lambda$, to some characteristic length, $L$, quantifies the continuity of any flow, and when this parameter is large enough, alternative methods must be employed to simulate gases. The Direct Simulation Monte Carlo (DSMC) method is one which simulates rarefied gas flows by directly simulating the particles that compose the …

The Design And Implementation Of A Supersonic Indraft Tube Wind Tunnel For The Demonstration Of Supersonic Flows, Daniel Kenneth Johnson

Master's Theses

Historically, the endeavor of scale testing flight vehicles at supersonic Mach numbers, especially for long durations, has required the development of closed-loop wind tunnels, which are extremely expensive both to build and operate due to the high complexity and incredible power required to drive such a system. The intermittent blowdown wind tunnel, indraft tunnel, and shock tunnel have alleviated many of these cost requirements to some degree, whilst facilitating testing at very high Mach numbers and enthalpies; however, these systems require the handling of gases at pressures and temperatures that can be prohibitive for many university settings. The Ludwieg tube …

Single Camera Photogrammetry Matlab Solver Developed For Automation Of The Oil Interferometry Process, Hunter Michael Dunn

Master's Theses

Over the last 20 years, Gregory G. Zilliac of the NASA AMES Research Center has been in continuous development of a fringe-imaging skin friction PC application used in oil interferometry analysis. This application, CXWIN5G, allows users to analyze propagation of oil smears across an aerodynamic surface using photogrammetry. The purpose of this thesis is to investigate the feasibility of increasing the level of automation currently found in CXWIN5G by developing a MATLAB solver capable of determining oil smear geometry with minimal user input.

There are two main automation goals of this thesis that are reflected in the core of the …

Manufacturing And Instrumentation Of An Open End Compressed Air Shock Tube, Josue O. Ruiz

Master's Theses

Shock tubes have been used extensively to study shock wave structures and high speed flow features. The purpose of constructing this open end shock tube was to have the ability to produce shock waves in a laboratory setting but also understand the exit flow coming out which can be applied to future studies that are beyond the scope of this work. This undertaking would require that an open end shock tube be built and instrumented with PCB Integrated Circuit Piezoelectric (ICP) Pressure Sensor Model 113B24 that would then be connected to a PCB Model 482C05 Signal Conditioner with the purpose …

Wing Deflection Analysis Of 3d Printed Wind Tunnel Models, Matthew G. Paul

Master's Theses

This work investigates the feasibility of producing small scale, low aerodynamic loading wind tunnel models, using FDM 3D printing methods, that are both structurally and aerodynamically representative in the wind tunnel. To verify the applicability of this approach, a 2.07% scale model of the NASA CRM was produced, whose wings were manufacturing using a Finite Deposition Modeling 3D printer. Experimental data was compared to numerical simulations to determine percent difference in wake distribution and wingtip deflection for multiple configurations.

Numerical simulation data taken in the form of CFD and FEA was used to validate data taken in the wind tunnel …

Leading Edge Boundary Layer Suction Device For The Cal Poly Rolling Road Wind Tunnel, Daniel C. Glover, Liam M. Madden, Robert J. Cabri

Mechanical Engineering

Over the course of three quarters from Fall of 2016 to Spring of 2017, our team designed and built a boundary layer suction device. The boundary layer suction device has three main functions: a scoop that redirects most of the boundary layer air out of the wind tunnel, fans that suck the remaining boundary layer air through a porous plate and ducting and out of the wind tunnel, and a transition bridge that transitions the remaining air smoothly onto the rolling road. The wind tunnel is owned by Cal Poly and the rolling road is a new addition to it. …

An Investigation Of Avian Wing Tip Vortex Generation Using A Biomimetic Approach, David Stewart Martin

Master's Theses

An experimental study has been conducted to develop a process allowing the creation of biologically accurate aerodynamic test models mimicking the slotted primary feather geometry of the Brown Pelican (Pelecanus occidentalis). Preserved examples of both a full Brown Pelican wing and a single primary feather were 3D scanned and digitally reconstructed using a combination of MATLAB and CAD software. The final model was then 3D printed as a collection of smaller components using a LulzBot TAZ 6 printer and Taulman3D T-Glase PET filament. After using various surface finishing techniques to improve the finish of all 3D printed parts, …

Actuator Disk Theory For Compressible Flow, Htet Htet Nwe Oo

Master's Theses

Because compressibility effects arise in real applications of propellers and turbines, the Actuator Disk Theory or Froude’s Momentum Theory was established for compressible, subsonic flow using the three laws of conservation and isentropic thermodynamics. The compressible Actuator Disk Theory was established for the unducted (bare) and ducted cases in which the disk was treated as the only assembly within the flow stream in the bare case and enclosed by a duct having a constant cross-sectional area equal to the disk area in the ducted case. The primary motivation of the current thesis was to predict the ideal performance of a …

Assessment Of Asymmetric Flight On Solar Uas, Eric Belfield

Master's Theses

An investigation was conducted into the feasibility of using an unconventional flight technique, asymmetric flight, to improve overall efficiency of solar aircraft. In this study, asymmetric flight is defined as steady level flight in a non-wings-level state in- tended to improve solar incidence angle. By manipulating aircraft orientation through roll angle, solar energy collection is improved but aerodynamic efficiency is worsened due to the introduction of additional trim drag. A point performance model was devel- oped to investigate the trade-off between improvement in solar energy collection and additional drag associated with asymmetric flight. A mission model with a focus on …

Flow Meter Test Rig, Cory Davis, Emily Guss, Michael Swartz

Mechanical Engineering

As part of a fluid mechanics laboratory, there should be an experiment that demonstrates the proper use of flow meters, devices that are necessary and relevant in many fluids-related industries. In order to provide students with exposure to these types of devices and how they work, a test rig was developed with the ability to interchange a variety of flow meters in order to broaden the students’ knowledge of the different types of measuring devices. This report was also written to outline the steps taken to ensure the test rig would match a laboratory and industry setting. Additionally, it was …

Axisymmetric Bi-Propellant Air Augmented Rocket Testing With Annular Cavity Mixing Enhancement, Allen A. C. Capatina

Master's Theses

Performance characterization was undertaken for an air augmented rocket mixing duct with annular cavity configurations intended to produce thrust augmentation. Three mixing duct geometries and a fully annular cavity at the exit of the nozzle were tested to enable thrust comparisons. The rocket engine used liquid ethanol and gaseous oxygen, and was instrumented with sensors to output total thrust, mixing duct thrust, combustion chamber pressure, and propellant differential pressures across Venturi flow measurement tubes.

The rocket engine was tested to thrust maximum, with three different mixing ducts, three major combustion pressure sets, and a nozzle exit plane annular cavity (a …

Development Of Cpanel, An Unstructured Panel Code, Using A Modified Tls Velocity Formulation, Christopher R. Satterwhite

Master's Theses

The use of panel codes in the aerospace industry dates back many decades. Recent advances in computer capability have allowed them to evolve, both in speed and complexity, to provide very quick solutions to complex flow fields. By only requiring surface discretization, panel codes offer a faster alternative to volume based methods, delivering a solution in minutes, as opposed to hours or days. Despite their utility, the availability of these codes is very limited due to either cost, or rights restrictions.

This work incorporates modern software development practices, such as unit level testing and version control, into the development of …

Inlet Shape Considerations For Split-Wing Electric Distributed Propulsion, Kurt Vonderhaar Papathakis

Master's Theses

This thesis aims to uncover preliminary design relationships for an inlet of a split-wing electric distributed propulsion regional airliner. Several aspects of the inlet design were investigated, including: the overall thickness of the airfoil section with respect to the chord, inlet throat area, and lip radius. These parameters were investigated using several angles of attack and mass flow rates through the fan. Computational fluid dynamics, with a 2^nd Order turbulence model was used and validated against World War II era data from NACA, as those studies were the most pertinent wind tunnel data available. Additionally, other works by Boeing, …

Validation Of A Cfd Approach For Gas Turbine Internal Cooling Passage Heat Transfer Prediction, Daniel G. Wilde

Master's Theses

This report describes the development and application of a validated Computational Fluid Dynamics (CFD) modelling approach for internal cooling passages in rotating turbomachinery. A CFD Modelling approach and accompanying assumptions are tuned and validated against academically available experimental results for various serpentine passages. Criteria of the CFD modelling approach selected for investigation into advanced internal cooling flows include accuracy, robustness, industry familiarity, and computational cost.

Experimental data from NASA HOST (HOt Section Technology), Texas A&M, and University of Manchester tests are compared to RANS CFD results generated using Fluent v14.5 in order to benchmark a CFD modelling approach.

Capability of …

Experimental Investigation Of Drag Reduction By Trailing Edge Tabs On A Square Based Bluff Body In Ground Effect, Scott R. Sawyer

Master's Theses

This thesis presents an experimental investigation of drag reduction devices on a bluff body in ground effect. It has previously been shown that the addition of end-plate tabs to a rectangular based bluff body with an aspect ratio of 4 is effective in eliminating vortex shedding and reducing drag for low Reynolds number flows. In the present study a square based bluff body, both with and without tabs, will be tested under the same conditions, except this time operating within proximity to a ground plane in order to mimic the properties of bounded aerodynamics that would be present for a …

Cold Flow Performance Of A Ramjet Engine, Harrison G. Sykes

Master's Theses

The design process and construction of the initial modular ramjet attachment to the Cal Poly supersonic wind tunnel is presented. The design of a modular inlet, combustor, and nozzle are studied in depth with the intentions of testing in the modular ramjet. The efforts undertaken to characterize the Cal Poly supersonic wind tunnel and the individual component testing of this attachment are also discussed. The data gathered will be used as a base model for future expansion of the ramjet facility and eventual hot fire testing of the initial components. Modularity of the inlet, combustion chamber, and nozzle will allow …