Aerodynamics and Fluid Mechanics Commons^™

Rayleigh Test Apparatus Design Report, Josef Duller, Owen Raybould, James Nicovich

Mechanical Engineering

The Rayleigh Test Apparatus is a device that will be used to test the thermodynamic properties of Nitrous Oxide to assess the feasibility of using this fluid as a coolant for a hybrid rocket aero spike. The aero spike is intended to redirect the propulsion flow as it leaves the engine to create a more efficient flow pattern at low and high altitudes. However, there are issues of overheating which leads to melting of the aero spike. For this reason, the use of nitrous oxide (N2O) as a coolant is being explored. N20 is being considered because it is already …

Port Flow Test System, Daniel Chairez, Chelsea E. Crawford, Daniel S. Welch

Mechanical Engineering

Solar Turbines Gas Compressor Engineering Division of San Diego, California called upon the Mechanical Engineering students of California Polytechnic University, San Luis Obispo to provide recommendations for optimization of compressor end cap port design. Various sizes of compressors have end caps with numerous ports that exchange fluids between the inside and outside of the working fluid pressure vessel. Because so many ports must exist on the end caps, unusual flow paths are created to supply the appropriate location within the compressor. These flow paths commonly consist of a drilled inlet hole which intersects with a sudden expansion. The sudden expansion …

Airplane Landing Flare-The Last 5 Seconds, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Multidisciplinary Design Optimization Of Transonic Airfoil Sections Using Multiobjective Optimization And Computational Intelligence Tools, Amit A. Kulkarni

Mechanical & Aerospace Engineering Theses & Dissertations

The design of transonic airfoils for civil aviation applications has been a major engineering challenge in the last fifty years. This design problem arises due to the need to limit shock wave drag at a given transonic speed. In recent years, the requirement to reduce the levels of aircraft noise has started to affect the airfoil design process. The multidisciplinary aerodynamic shape optimization problem is treated in this thesis using a multi-objective approach. The objectives correspond to the design of transonic airfoil sections with low drag during cruise and low trailing edge noise levels during the approach condition. The optimization …

Perch Landing Maneuvers And Control For A Rotating-Wing Mav, Jonathan Louis Lubbers

University of Kentucky Master's Theses

This thesis addresses flight control of the perch landing maneuver for micro-aerial vehicles. A longitudinal flight model is constructed for a pigeon-sized aircraft. In addition to a standard elevator control surface, wing-rotation also considered as a non-standard actuator for increasing low-speed aerodynamic braking. Optimal state and control trajectories for the perch landing maneuver are computed using commercial software. A neighboring optimal control law is then developed and implemented in a set of flight simulations. Simulations are run with both a quasisteady and an unsteady aerodynamic model. The effectiveness of wing rotation and of the neighboring optimal control law is discussed, …

A Shock Tube Technique For Blast Wave Simulation And Studies Of Flow Structure Interactions In Shock Tube Blast Experiments, Nicholas N. Kleinschmit

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Improvised explosive devices (IED’s) are widely used against US and allied forces fighting in Iraq and Afghanistan. Exposure to IED blast may cause blast-induced traumatic brain injury (bTBI). The injury mechanisms are however not well understood. A critical need in bTBI-related research is the ability to replicate the loading conditions of IED blast waves in a laboratory environment. In this work, experimental studies have been carried out to explore the use of the shock tube technique for generating air shock waves that mimic the temporal and spatial characteristics of free-field blast waves and to investigate the blast wave-test sample interactions …

Implementation Of A Conrad Probe On A Boundary Layer Measurement System, Charles Rocky Ulk

Master's Theses

This thesis presents the design, calibration, and performance evaluation of a type of two-hole pressure probe anemometer known as a Conrad probe, as well as its subsequent implementation on an autonomous, compact boundary layer measurement device and its first application for subsonic in-flight measurements of a swept wing boundary layer. Calibration of the Conrad probe was accomplished using two calibration functions and a non-nulling method for resolving in-plane flow velocity direction and magnitude over a range of ±30 degrees. This approach to calibration and application offered the advantages of rapid data acquisition with lower energy consumption than alternative methods for …

Analysis Of Wake Vortices Of A Medium Range Twin-Propeller Military Cargo Aircraft Using Statistically Designed Experiments, Burhan Sahin

Mechanical & Aerospace Engineering Theses & Dissertations

An experimental study was initiated to analyze the trajectories of the streamwise vortices behind the wing tip and flap of a medium range and propeller driven twin-engine military cargo aircraft. The model used for the experimental study was a generic, high wing and half model of a propeller driven aircraft and mounted within Old Dominion University's Low Speed Wind Tunnel where the wind tunnel flow speed was set to constant value of 9 m/sec. The main purpose of the study was to reach regression models for the motion and vorticity strength of both vortices under varying factors such as angle …

Thermal Modeling Of Lithium-Ion Energy Storage Systems For Hybrid Electric Vehicles Using Computational Fluid Dynamics With Conjugate Heat Transfer, Craig R. Czlapinski

Master's Theses - Daytona Beach

The success and performance of a Hybrid Electric Vehicle (HEV) relies largely on its Energy Storage System (ESS). High temperatures and thermal variations can significantly affect a battery's performance and lifecycle. An effective thermal management system is vital to the health and safe operation of the ESS's batteries. A well designed thermal management system begins with the accurate prediction of the battery's thermal conditions. In hot climates, HEVs may be required to operate within ten degrees Celsius of the maximum safe operating temperature of their batteries. This study aims to evaluate the thermal management system of a lithium-ion based energy …

Rayleigh Flow Of Two-Phase Nitrous Oxide As A Hybrid Rocket Nozzle Coolant, Lauren May Nelson

Master's Theses

The Mechanical Engineering Department at California Polytechnic State University in San Luis Obispo currently maintains a lab-scale hybrid rocket motor for which nitrous oxide is utilized as the oxidizer in the combustion system. Because of its availability, the same two-phase (gas and liquid) nitrous oxide that is used in the combustion system is also routed around the throat of the hybrid rocket’s converging-diverging nozzle as a coolant. While this coolant system has proven effective empirically in previous tests, the physics behind the flow of the two-phase mixture is largely unexplained. This thesis provides a method for predicting some of its …

A System For Measuring The Lift And Drag Forces Of A Spinning Golf Ball Held Fixed Within A Wind Tunnel, Ryan R. Miller

Master's Theses

A system was designed, built and tested in order to test the aerodynamic properties of a standard golf ball in a wind tunnel manufactured by ELD, Inc. model 406(B). The system consists of a rotating shaft, on which the golf ball is attached, connected to a two-axis force transducer. Additionally, an automated data acquisition system was built for enhanced precision of measurements. Data for wind speeds up to 160 ft/s and rotational speeds up to 8,600 rpm were obtained and analyzed. The purpose of the designed apparatus was to allow for studies to better understand the lift and drag coefficients …

Computational And Experimental Investigation Of The Flow Structure And Vortex Dynamics In The Wake Of A Formula 1 Tire, John Axerio, Gianluca Iaccarino, Emin Issakhanian, Chris Elkins, John Eaton

Mechanical Engineering Faculty Works

The flowfield around a 60% scale stationary Formula 1 tire in contact with the ground in a closed wind tunnel was examined experimentally in order to assess the accuracy of different turbulence modeling techniques. The results of steady RANS and Large Eddy Simulation (LES) were compared with PIV data, which was obtained within the same project. The far wake structure behind the wheel was dominated by two strong counter-rotating vortices. The locations of the vortex cores, extracted from the LES and PIV data as well as computed using different RANS models, showed that the LES predictions are closest to the …

Experimental Investigation Of Active Control Of Bluff Body Vortex Shedding, Ilteris Koc

Mechanical & Aerospace Engineering Theses & Dissertations

Mean and fluctuating forces acting on a body are strongly related to vortex shedding generated behind it. Therefore, it is possible to obtain substantial reductions of at least the unsteady forces if vortex shedding is controlled or its regularity is reduced. While conventional active flow control methods are mainly concerned with direct interaction with, and alteration of, the mean flow about a body, modern techniques involve altering existing flow instabilities using relatively small inputs to obtain large-scale changes of mean flows. Aerodynamic flow control may be intended to delay or suppress boundary layer separation through creation of a boundary layer …

Modeling Redox-Based Magnetohydrodynamics In Three-Dimensional Microfluidic Channels, Hussameddine S. Kabbani, Aihua Wang, Xiaobing Luo, Shizhi Qian

Mechanical Engineering Faculty Research

RedOx-based magnetohydrodynamic MHD[1] flows in three-dimensional microfluidic channels are investigated theoretically with a coupled mathematical model consisting of the Nernst-Planck equations for the concentrations of ionic species, the local electroneutrality condition for the electric potential, and the Navier-Stokes equations for the flow field. A potential difference is externally applied across two planar electrodes positioned along the opposing walls of a microchannel that is filled with a dilute RedOx electrolyte solution, and a Faradaic current transmitted through the solution results. The entire device is positioned under a magnetic field which can be provided by either a permanent magnet or an electromagnet. …

Adaptive Control Of A Projectile Fin Using Piezoelectric Elastic Beam, Smitha Mani, Sahjendra N. Singh, Surya Kiran Parimi, Woosoon Yim, Mohamed B. Trabia

Mechanical Engineering Faculty Research

No abstract provided.

Numerical Study Of Combustion Of Hydrogen And Ethylene In A Two-Dimensional Dual-Mode Scramjet Combustor, Robert A. Carson

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis presents computational fluid dynamics results for two-dimensional flow geometries utilizing two fuels, hydrogen (H2) and ethylene (C2H4). Upstream interaction was evident with the use of both fuels due in part to recirculation in the combustor, the inlet pressures and the combustion process. Results were obtained for hydrogen using a reduced chemical kinetic model while results obtained for ethylene employed a reduced chemical kinetic model as well as an expanded chemical kinetic model.

Initially, an examination of grid composition was conducted in order to select the most numerically efficient and accurate grid for reacting flow in the current combustor …

External Aerodynamics Of Heavy Ground Vehicles: Computations And Wind Tunnel Testing, Ilhan Bayraktar

Mechanical & Aerospace Engineering Theses & Dissertations

Aerodynamic characteristics of a ground vehicle affect vehicle operation in many ways. Aerodynamic drag, lift and side forces have influence on fuel efficiency, vehicle top speed and acceleration performance. In addition, engine cooling, air conditioning, wind noise, visibility, stability and crosswind sensitivity are some other tasks for vehicle aerodynamics. All of these areas benefit from drag reduction and changing the lift force in favor of the operating conditions. This can be achieved by optimization of external body geometry and flow modification devices. Considering the latter, a thorough understanding of the airflow is a prerequisite.

The present study aims to simulate …

Suppression Of Post-Buckling Deflection And Panel-Flutter Using Shape Memory Alloy, Mohammad Tawfik Abo El So-Oud

Mechanical & Aerospace Engineering Theses & Dissertations

A novel concept proposed is the use of Shape Memory Alloy (SMA) to reduce the panel thermal deflection and flutter responses. SMA has unique ability to recover large prestrains completely when the alloy is heated (by aerodynamic heating in the present case) above the austenite start temperature A_s. During the recovery process, a large tensile recovery stress occurs if the SMA is restrained.

In this thesis, a panel subject to the combined aerodynamic and thermal loading is investigated. A nonlinear finite element model based on von Karman strain displacement relation is utilized to study the effectiveness of SMA …

Design Methodology For Low Speed High Altitude Long Endurance Unmanned Aerial Vehicles, Aaron Altman

Mechanical and Aerospace Engineering Faculty Publications

High Altitude Long Endurance (HALE) Unmanned Aerial Vehicles (UAV's) are increasingly being considered to perform a wide range of tasks. Recent years have seen greater value of UAV's in the military reconnaissance arena, first in the Persian Gulf war, with the use of small UAV's, and more recently over Bosnia with medium sized UAV's.

The NASA ERAST program uses HALE UAV's for environmental sensing and monitoring. The military has investigated using HALE UAV's for Theater Ballistic Missile defense, as well as general battlefield reconnaissance. Proposals have been made to use HALE UAV's for communications relay, long term surveillance (with a …

Vortex Wake And Exhaust Plume Interaction, Including Ground Effect, Ihab Gaber Adam

Mechanical & Aerospace Engineering Theses & Dissertations

Computational modeling and studies of the near-field wake-vortex turbulent flows, far-field turbulent wake-vortex/exhaust-plume interaction for subsonic and High Speed Civil Transport (HSCT) airplane, and wake-vortex/exhaust-plume interaction with the ground are carried out. The three-dimensional, compressible Reynolds-Averaged Navier-Stokes (RANS) equations are solved using the implicit, upwind, Roe-flux-differencing, finite-volume scheme. The turbulence models of Baldwin and Lomax, one-equation model of Spalart and Allmaras and two-equation shear stress transport model of Menter are implemented with the RANS solver for turbulent-flow modeling.

For the near-field study, computations are carried out on a fine grid for a rectangular wing with a NACA-0012 airfoil section and …

Three-Dimensional Aerodynamic Design Optimization Using Discrete Sensitivity Analysis And Parallel Computing, Amidu Olawale Oloso

Mechanical & Aerospace Engineering Theses & Dissertations

A hybrid automatic differentiation/incremental iterative method was implemented in the general purpose advanced computational fluid dynamics code (CFL3D Version 4.1) to yield a new code (CFL3D.ADII) that is capable of computing consistently discrete first order sensitivity derivatives for complex geometries. With the exception of unsteady problems, the new code retains all the useful features and capabilities of the original CFL3D flow analysis code. The superiority of the new code over a carefully applied method of finite-differences is demonstrated.

A coarse grain, scalable, distributed-memory, parallel version of CFL3D.ADII was developed based on "derivative stripmining". In this data-parallel approach, an identical copy …

A Feasibility Study Of Fuel Cell Cogeneration In Industry, Scott B. Phelps, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

Up until now, most of the literature on fuel cell cogeneration describes cogeneration at commercial sites. In this study, a PC25C phosphoric acid fuel cell cogeneration system was designed for an industrial facility and an economic analysis was performed. The US DOE Industrial Assessment Center (IAC) database was examined to determine what industry considers a good investment for energy saving measures. Finally, the results of the cogeneration analysis and database investigation were used to project the conditions in which the PC25C might be accepted by industry.

Analysis of IAC database revealed that energy conservation recommendations with simple paybacks as high …

The Effectiveness Of Film Cooling In A Hypersonic Flowfield With Favorable Pressure Gradients, Julie A. Young

Mechanical & Aerospace Engineering Theses & Dissertations

The impetus of this technical document is to report results of aerothermodynamic cooling of a scramjet nozzle under favorable pressure gradients. The goals of film cooling are to protect the nozzle skin from the high enthalpy combustor flow, reduce regenerative cooling requirements, and decrease nozzle skin friction. A hypersonic nozzle configuration for which experimental data exists was selected as the basis of this numerical study. As a first step, the numerical results of film cooling along a flat plate are compared to previous literature to validate the numerical model. Subsequently, computations are performed to study the effects of varying the …

Sensitivity Analysis And Optimization Of Aerodynamic Configurations With Blend Surfaces, Almuttil Mathew Thomas

Mechanical & Aerospace Engineering Theses & Dissertations

A novel (geometrical) parametrization procedure using solutions to a suitably chosen fourth order partial differential equation is used to define a class of airplane configurations. Inclusive in this definition are surface grids, volume grids, and grid sensitivity. The general airplane configuration has wing, fuselage, vertical tail and horizontal tail. The design variables are incorporated into the boundary conditions, and the solution is expressed as a Fourier series. The fuselage has circular cross section, and the radius is an algebraic function of four design parameters and an independent computational variable. Volume grids are obtained through an application of the Control Point …

Implementation Of A Multiblock Sensitivity Analysis Method In Numerical Aerodynamic Shape Optimization, James Matthew Lacasse

Mechanical & Aerospace Engineering Theses & Dissertations

A multiblock sensitivity analysis method is applied in a numerical aerodynamic shape optimization technique. The Sensitivity Analysis Domain Decomposition (SADD) scheme which is implemented in this study was developed to reduce the computer memory requirements resulting from the aerodynamic sensitivity analysis equations, Discrete sensitivity analysis offers the ability to compute quasi-analytical derivatives in a more efficient manner than traditional finite-difference methods, which tend to be computationally expensive and prone to inaccuracies.

The direct optimization procedure couples CFD analysis based on the two-dimensional thin-layer Navier-Stokes equations with a gradient-based numerical optimization technique. The linking mechanism is the sensitivity equation derived from …

Computation Of The Aerodynamic Characteristics Of A Subsonic Transport Aircraft Using A Panel Method, Lillianne Plaster Whitelock Troeger

Mechanical & Aerospace Engineering Theses & Dissertations

An advanced low-order panel method, VSAERO, is applied to a full-configuration transport aircraft. Wing pressure distributions as well as lift, drag, and pitching moment coefficients calculated for the full computational configuration are compared with experimental data. In addition, partial configurations are evaluated computationally to determine the relevance of certain complex aircraft components to the computations. It is shown that the wing-surface pressure distributions and pitching moment coefficient are well predicted by VSAERO. The lift coefficient is consistently overpredicted by the code.

Simultaneous Aerodynamic Analysis And Design Optimization, Satish Venkatasubra Mani

Mechanical & Aerospace Engineering Theses & Dissertations

An efficient approach for simultaneous aerodynamic analysis and design optimization is presented. Using this approach, the expensive procedure of performing complete steady— state flow analyses at every design-optimization step is avoided, thus addressing the challenge of incorporating computational fluid dynamics software into efficient gradient—based optimization techniques for aerodynamic design. An adjoint—variable method is introduced to nullify the effect of an increased number of design variables in this problem formulation. This approach is successfully tested on two quasi—one—dimensional nozzle—flow problems: a fully supersonic flow, and also a transonic flow with a normal shock. The algorithm is implemented using the direct Newton—iteration …

An Experimental And Analytical Investigation Of Wing Flutter On A Trial Rotor V/Stol Aircraft, David L. Soistmann

Mechanical & Aerospace Engineering Theses & Dissertations

A wind tunnel model based on a trail rotor vehicle concept was tested for wing flutter in the subsonic flow regime. The wind tunnel model was flutter tested in the forward flight mode only. From this test it was determined that this conceptual vehicle may be susceptible to wing flutter. However, the flutter encountered was not catastrophic but was of the limited amplitude type. The trailing rotor blades were found to have a positive aerodynamic damping effect on flutter. The flutter mechanism for each flutter point was due to a coupling of the first wing bending and first wing torsion …

Domain Decomposition For Multigrid, Finite Volume Flow Solvers, Victor Robert Lessard

Mechanical & Aerospace Engineering Theses & Dissertations

Computing the flow fields about three-dimensional complex configurations accurately becomes a difficult task, if it is attempted to generate a single, body fitted grid with proper clustering. The domain decomposition methods, which divide the computational domain into less complex subdomains, are extensively used to decrease the grid generation workload. A domain decomposition technique also allows the use of different solution methods for different subdomains. The objective of this work is to develop a domain decomposition method via overlapping/embedding the component grids, which is to be used by upwind, multigrid, finite volume solution algorithms. A computer code, given the name MaGGiE, …

Calculations Of Three-Dimensional Transonic Flows Using The Implicit Formulation Of The Isenthalpic Euler Equations With Flux Vector Splitting, Frank E. Cannizzaro

Mechanical & Aerospace Engineering Theses & Dissertations

A numerical method for solving three-dimensional transonic flows using the isenthalpic formulation of the Euler equations is developed. The method uses van Leer's flux vector splitting to solve the implicit formulation of the governing equations, which are applied to a cell centered finite-volume scheme. A three factor spatial approximate factorization is implemented in solving the implicit part of the governing equations. Time marching to a steady state solution requires short computational times due to the relative efficiency of the basic method. Computational times are further reduced by the implementation of the multigrid acceleration technique, which provided converged solutions in approximately …