Aerospace Engineering Commons^™

Design And Numerical Simulation Of Two Dimensional Ultra Compact Combustor Model Sections For Experimental Observation Of Cavity-Vane Flow Interactions, David S. Moenter

Theses and Dissertations

An improved computational fluid dynamics (CFD) model was developed for numerical simulation of the Ultra Compact Combustor (UCC) concept to enhance turbulent flow characterization of the circumferentially traveling, centrifugal-force enhanced combustion, cavity flow into the engine main flow passage via a radial cavity in the turbine axial guide vanes. The CFD model uses a dense grid on a 60° periodic, axisymmetric combustor section, with the RNG κ-ε turbulence model to resolve turbulent flow details. An overall analysis and performance evaluation of the experimentally tested UCC configuration and an axially shortened cavity baseline configuration was conducted at various experimentally documented operating …

Particle Image Velocimetry Using A Novel, Non-Intrusive Particle Seeding, Charles J. Delapp Ii

Theses and Dissertations

The purpose of this research effort was to study the use of non-intrusive particle seeding for Particle Image Velocimetry (PIV). Current seeding material and techniques involve the use of either solid particles or liquid mixtures which can contaminate or damage closed circuit wind tunnels, and in some cases can introduce a potential fire or explosive hazard. The proposed method is based on creating seed particles utilizing Carbon Dioxide (CO2). The CO2 would be dispensed into the flow as a liquid, immediately condensing to solid seed particles as they leave the spray nozzle. The advantage of using these particles is that …

Dynamic Nonlinear Bending And Torsion Of A Cantilever Beam, Michael S. Whiting

Theses and Dissertations

This effort sought to measure the dynamic nonlinear bending and torsion response of a cantilever beam. The natural frequencies of a cantilever beam in both chord and flap directions were measured at different static root pitch angles with varying levels of weights attached at the free end. The results were compared with previous experimentation to validate the data and testing procedures while lowering the associated error bands. Additionally, methodology for measuring mode shapes was set forth and mode shapes were measured for a few test cases with zero degrees of root pitch.

Assessing The Potential For Improved Scramjet Performance Through Application Of Electromagnetic Flow Control, Martin F. Lindsey

Theses and Dissertations

Hypersonic flight using scramjet propulsion bridges the gap between turbojets and rockets. Recent efforts focus on magnetogasdynamic (MGD) flow control to mitigate the problems of high thermomechanical loads and low efficiencies associated with scramjets. This research is the first flight-scale, three-dimensional computational analysis of a realistic scramjet to assess how MGD flow control improves scramjet performance. Developing a quasi-one dimensional design tool culminated in the first open source scramjet geometry. This geometry was tested with the Air Force Research Laboratory's electromagnetic computational code. To increase fidelity, an algorithm was developed to incorporate thermochemistry, resulting in the only open-source model of …

Store Separations From A Supersonic Cone, Richard J. Simko

Theses and Dissertations

The purpose of this research was to analyze the environment a store would travel through if ejected from a supersonic cone. This was done using the Beggar Computational Fluid Dynamics (CFD) code from the Air Force SEEK Eagle Office at Eglin Air Force Base, FL. CFD simulations were compared to experimental results from a previous AFIT thesis and conclusions were drawn based on whether or not the current wind tunnel setup at AFIT is capable of performing analyses of supersonic store separations. Also included in this research is a study of supersonic base pressure profiles, near-wake velocity profiles, wind tunnel …

Study Of Magnetogasdynamic Flow Acceleration In A Scramjet Nozzle, Erik K. Ross

Theses and Dissertations

The research project studied the benefits of Magnetogasdynamic (MGD) acceleration on a scramjet nozzle. MGD is a technology that relies on electromagnetic fields to extract and/or add energy to flow fields. The scramjet engine in the "AJAX" concept proposed by D.I. Brichkii et al. (2001) of St. Petersburg, Russia would utilize an MGD power generator in the diffuser user which could potentially provide electrical power for the aircraft support systems and an MGD accelerator in the nozzle of the engine. Using an AFRL/VAAC CFD code that was modified for MGD computations, this project investigated the effect conductivity and load factor …

A Computational Study Of Thermo-Fluid Dynamics Of Pulse Detonation Engines, Alberto Davila Urresti

Master's Theses - Daytona Beach

The purpose of this thesis is to use a transient Computational Fluid Dynamics computer code written in FORTRAN 90 for full reaction kinetics, to perform an analysis of the physical processes and chemical phenomena occurring on a single cycle of an ideal Pulse Detonation Engine (PDE) using a stoichiometric mixture of H₂ and O₂. A small zone of high pressure and temperature is used to initiate the detonation wave in the PDE. A simple case with no chemical reactions and the same PDE geometry and “computational spark” is also tested. The speed of the wave relative to …

Development Of A Higher-Order Upwind Algorithm For Compressible Fluid Flow, Barry A. Croker

Theses and Dissertations

A global fourth-order solution method that incorporates compact differencing with Roe's approximate Riemann solver was investigated. This method was incorporated into a one-dimensional numerical simulation of the compressible Euler equations, and applied to a one-dimensional shock tube problem. The method was also extended to two dimensions, and applied to a two-dimensional shock tube problem and an advecting vortical structure problem on both rectilinear and curvilinear meshes. The results were compared to a third-order Roe scheme and a fourth-order compact difference scheme. An order of accuracy determination showed that it has an order of accuracy somewhere near fourth order, with absolute …

Boundary Layer Flow Control Using Plasma Induced Velocity, Brian E. Balcer

Theses and Dissertations

An examination of the effects of plasma induced velocity on boundary layer flow was conducted. A pair of thin copper film electrodes spanned the test section, oriented at thirty degrees from normal to the free stream flow. An adverse pressure gradient was imposed over the electrode configuration using a pressure coefficient profile similar to that associated with suction side of a Pac-B low pressure turbine blade. In addition, suction was applied to keep flow attached on the upper wall, inducing separation over the electrode. The electrode is supplied by an AC source at three different power levels with the free …

Numerical Analysis And Optimization Of The Ultra Compact Combustors, Roger T. Greenwood

Theses and Dissertations

In an effort to increase thrust per weight ratio and decrease pollutant emissions of aero-turbine jet engines, a circumferentially burning Ultra Compact Combustor (UCC) with a Cavity-in-a-Cavity design has been developed. A numerical analysis of this design has been conducted and compared with experimental results. The CFD model has been validated through a wide range of conditions and four alternative physical configurations of the UCC have been modeled. Emissions, combustor efficiencies, temperature and velocity profiles, and pressure drop values were used as comparison parameters. Numerical results indicate that increasing the outflow area will increase the pressure drop over the combustor …

Validation Of Turbulence Models In The Beggar Code For Unsteady Flow, Kevin G. Storm

Theses and Dissertations

Validation of the turbulence models in the CFD code Beggar for unsteady turbulent flow are discussed. Six validation cases of the code are considered, three cases with the intent of validating the code without the turbulence model and three cases to validate the turbulence model itself. Finally, a more realistic simulation of a simplified store is examined. The turbulence models considered are the Baldwin-Lomax, Spalart-Allmaras, and a DES model. The conclusions made deal with necessary prerequisites to properly simulating unsteady turbulent flow and model selection. The prerequisites necessary in the Beggar code are a second order temporal discretization and the …

Desktop Computer Programs For Preliminary Design Of Transonic Compressor Rotors, Brian C. Mcdonald

Theses and Dissertations

A need exist for correlation-based desktop computer programs that predict the flow through transonic compressor rotors with nominal computational time and cost. Modified versions of two desktop computer programs, BOWSHOCK and TRANSROTOR, were used to perform a parametric study on a modem compressor rotor. BOWSHOCK calculates the exit flow properties of a supersonic streamtube through a user-defined compressor rotor. TRANSROTOR calculates flow properties at three stations in a user-defined compressor stage. Modifications to TRANSROTOR included the incorporation of a recently published rotor loss model. Baseline and modified TRANSROTOR versions were run with two modern transonic compressor blades. Results were compared …

Analysis Of The Application Of A Triggered Isomer Heat Exchanger As A Replacement For The Combustion Chamber In An Off-The-Shelf Turbojet, Carl R. Hartsfield

Theses and Dissertations

The objective of this research was to evaluate the feasibility of using the triggered decay of a radioactive isomer in a solid-state heat exchanger to power a gas turbine engine. Primary performance measures were stagnation temperature increase and stagnation pressure drop across the heat exchanger. Analysis was performed using commercial software, and explored three types of heat exchanger: concentric tubes, radial fins with constant spacing, and radial fins with constant thickness. All met or exceeded performance of the baseline J-57 turbojet engine at static sea level conditions. A single configuration of heat exchanger, using concentric tubes, was evaluated at typical …

Simulation And Analysis Of Wing Rock Physics For A Generic Fighter Model With Three Degrees-Of-Freedom, Ahmed Saad

Theses and Dissertations

Modern fighter designs have been associated with lateral self-excited oscillations own as "Wing Rock". Simulations of wing rock by flow visualization utilities have been encouraged to develop a complete understanding of the fluid mechanism that drives the motion as well as for prediction purposes. Previous wind/water tunnel simulations have been limited to a single degree-of freedom (DoF) in roll. In this study, for the first time, wing rock is computationally simulated in three DoF: roll, sideslip, and vertical motion to study the effect of adding file sideslip and vertical motion. The results are for a generic fighter model consisting of …

A Study Of The Volume Of Fluid Method For Moving Boundary Problems, Marianne Francois

Master's Theses - Daytona Beach

Moving boundary problems are often encountered in engineering and science. One of the methods to solve such problems numerically is the volume of fluid (VOF) method. The VOF method uses an additional field variable/to track the interface using the Eulerian fixed grid. In this work, the VOF method is combined with the Continuum surface force model. The governing flow equations for Newtonian fluids in incompressible flow in two dimensions are solved using the pressure-based algorithm. A linear interface reconstruction algorithm is developed and improved by interpolations. In order to validate the code, the problem of the convection of a two-fluid …

The Effectiveness Of Film Cooling In A Hypersonic Flowfield With Favorable Pressure Gradients, Julie A. Young

Mechanical & Aerospace Engineering Theses & Dissertations

The impetus of this technical document is to report results of aerothermodynamic cooling of a scramjet nozzle under favorable pressure gradients. The goals of film cooling are to protect the nozzle skin from the high enthalpy combustor flow, reduce regenerative cooling requirements, and decrease nozzle skin friction. A hypersonic nozzle configuration for which experimental data exists was selected as the basis of this numerical study. As a first step, the numerical results of film cooling along a flat plate are compared to previous literature to validate the numerical model. Subsequently, computations are performed to study the effects of varying the …

Dynamic Unstructured Method For Prescribed And Aerodynamically Determined Relative Moving Boundary Problems, Kamakhya Prasad Singh

Mechanical & Aerospace Engineering Theses & Dissertations

A new methodology is developed to simulate unsteady flows about prescribed and aerodynamically determined moving boundary problems. The method couples the fluid dynamics and rigid-body dynamics equations to capture the time-dependent interference between stationary and moving boundaries. The unsteady, compressible, inviscid (Euler) equations are solved on dynamic, unstructured grids by an explicit, finite-volume, upwind method. For efficiency, the grid adaptation is performed within a window around the moving object. The Eulerian equations of the rigid-body dynamics are solved by a Runge-Kutta method in a non-inertial frame of reference. The two-dimensional flow solver is validated by computing the flow past a …

Computation Of The Aerodynamic Characteristics Of A Subsonic Transport Aircraft Using A Panel Method, Lillianne Plaster Whitelock Troeger

Mechanical & Aerospace Engineering Theses & Dissertations

An advanced low-order panel method, VSAERO, is applied to a full-configuration transport aircraft. Wing pressure distributions as well as lift, drag, and pitching moment coefficients calculated for the full computational configuration are compared with experimental data. In addition, partial configurations are evaluated computationally to determine the relevance of certain complex aircraft components to the computations. It is shown that the wing-surface pressure distributions and pitching moment coefficient are well predicted by VSAERO. The lift coefficient is consistently overpredicted by the code.

Simulation Of Vertical Tail Buffet In Internal Vortex Breakdown Flows, Mark William Flanagan

Mechanical & Aerospace Engineering Theses & Dissertations

Computational simulation of vertical tail buffet in an internal vortex breakdown flow is considered. The fiuid-flow problem is formulated using the full, compressible, unsteady Navier-Stokes equations which are solved using an implicit, flux-difference splitting, finite volume scheme. The fluid-flow problem is solved in a configured circular duct using quasi-axisymmetric assumptions to simplify the flow equations. A plate is placed transverse to the incoming flow. Solution of the flow in the duct is performed with and without a rigid plate, and with and without an elastic plate. The elastic response of the plate is calculated assuming that it is a cantilever …

Application Of Sensitivity Analysis To The Euler Equations, Vamshi Mohan Korivi

Mechanical & Aerospace Engineering Theses & Dissertations

An approximation method is presented for efficiently predicting the changes which occur in a steady-state numerical solution of the Euler equations as a consequence of a small change in the geometric shape of the domain. The method is extended to develop a general procedure for calculating aerodynamic sensitivity derivatives with respect to variations of geometric shape. The techniques are implemented using an upwind cell centered finite volume formulation, and are applied to two test cases, (1) a subsonic nozzle (M_∞ = 0.85), and (2) a supersonic inlet (M_∞ = 2.0). Conventional numerical solutions are first obtained for flow …

Navier-Stokes Analysis Of Cold Gas Scramjet Nozzle-Afterbody Flowfields, Walter C. Engelund

Mechanical & Aerospace Engineering Theses & Dissertations

The recent renewal of interest in hypersonic aerodynamics, brought about largely in part due to the development of the National Aerospace Plane (NASP), is resulting in an increased reliance on computational fluid dynamics for flowfield data in this flight regime. The design of the nozzle-afterbody section for a hypersonic transport such as the NASP is currently underway, and is being conducted using both computational fluid dynamics and cold, non-reacting, simulant gas experimental models. In this study, a computational analysis is conducted for the flow through a scramjet nozzle-afterbody test section.

Computations have been performed for a cold gas simulation of …

Domain Decomposition For Multigrid, Finite Volume Flow Solvers, Victor Robert Lessard

Mechanical & Aerospace Engineering Theses & Dissertations

Computing the flow fields about three-dimensional complex configurations accurately becomes a difficult task, if it is attempted to generate a single, body fitted grid with proper clustering. The domain decomposition methods, which divide the computational domain into less complex subdomains, are extensively used to decrease the grid generation workload. A domain decomposition technique also allows the use of different solution methods for different subdomains. The objective of this work is to develop a domain decomposition method via overlapping/embedding the component grids, which is to be used by upwind, multigrid, finite volume solution algorithms. A computer code, given the name MaGGiE, …

An Adaptive Remeshing Finite Element Method For High-Speed Compressible Flows Using Quadrilateral And Triangular Elements, Gururaja R. Vemaganti

Mechanical & Aerospace Engineering Theses & Dissertations

In this study a new adaptive remeshing method for high speed compressible flow analysis is presented. The method uses quadrilateral elements where possible, and triangles are introduced as needed. The primary goal of this study is to develop a remeshing method which uses both the concepts of unstructured and structured meshes for the finite element analysis to predict accurate aerodynamic heating in problems related to high speed viscous flows. The remeshing method uses a solution based on an old mesh to create a new mesh based on an advancing front technique. In the present implementation, a structured mesh of quadrilaterals …