Aerospace Engineering Commons^™

Robust Nonlinear Estimation And Control Applications Using Synthetic Jet Actuators, Natalie Ramos Pedroza

Doctoral Dissertations and Master's Theses

Limit cycle oscillations (LCO), also known as utter, cause significant challenges in flight control of small unmanned aerial vehicles (SUAVs), and could potentially lead to structural damage and catastrophic failures. LCO can be described as vibrational motions in the rocking, pitching and plunging displacements of an aircraft wing. To address this, the use of synthetic jet actuators (SJAs) in UAV flight control systems is becoming popular as a practical alternative and to mechanical deflection surfaces.

Synthetic jet actuators are promising tools for LCO suppression systems in small UAVs due to their small size, ease of operation, and low cost. Uncertainties …

Model Predictive Power Management Of A Hybrid Electric Propulsion System For Aircraft, Tyler J. Wall

Masters Theses

This work presents the switched optimal power flow control for an aircraft with a hybrid electric propulsion system. The propulsion system is a switched system that operates in either of two modes: (i) battery discharging and electric motor propelling and (ii) battery charging and electric motor generating. The aircraft model and components that form the hybrid propulsion system are modeled as either an algebraic power source/sink or as a dynamic model with appropriate power and state interconnections. With the system model defined, a model predictive control power management strategy is set fourth which minimizes a performance index that includes altitude …

A Study On The Control, Dynamics, And Hardware Of Micro Aerial Biomimetic Flapping Wing Vehicles, Siara Hunt

Doctoral Dissertations and Master's Theses

Biological flight encapsulates 400 million years of evolutionary ingenuity and thus is the most efficient way to fly. If an engineering pursuit is not adhering to biomimetic inspiration, then it is probably not the most efficient design. An aircraft that is inspired by bird or other biological modes of flight is called an ornithopter and is the original design of the first airplanes. Flapping wings hold much engineering promise with the potential to produce lift and thrust simultaneously. In this research, modeling and simulation of a flapping wing vehicle is generated. The purpose of this research is to develop a …

Cyber-Physical System Characterization And Co-Regulation Of A Quadrotor Uas, Seth E. Doebbeling

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

An Unmanned Aircraft System (UAS) is a Cyber-Physical System (CPS) in which a host of real-time computational tasks contending for shared resources must be cooperatively managed to obtain mission objectives. Traditionally, control of the UAS is designed assuming a fixed, high sampling rate in order to maintain reliable performance and margins of stability. But emerging methods challenge this design by dynamically allocating resources to computational tasks, thereby affecting control and mission performance. To apply these emerging strategies, a characterization and understanding of the effects of timing on control and trajectory following performance is required. Going beyond traditional control evaluation techniques, …

Flight Control And Hardware Design Of Multi-Rotor Systems, Nathan M. Zimmerman

Master's Theses (2009 -)

This thesis overviews crucial concepts involved in achieving quadcopter flight such as orientation estimation and control system implementation. This thesis also presents researchers with comprehensive hardware and software specifications for a quadcopter system. The primary application for this system would be for research with regards to the implementation of advance control techniques as well as data acquisition. Key constructs of this system include hardware software specifications for a flight controller, the radio system, and the sensorless brushless motor controllers. Firstly, the thesis starts by developing a reference frame and a mathematical model for the quadcotper system. Next, flight orientation estimation …

Attitude Determination & Control System Design And Implementation For A 6u Cubesat Proximity Operations Mission, Francisco J. Franquiz

Doctoral Dissertations and Master's Theses

The purpose of this work is to discuss the attitude determination and control system (ADCS) design process and implementation for a 12 kg, 6U (36.6 cm x 23.9 cm x 27.97 cm) CubeSat class nano-satellite. The design is based on the requirements and capabilities of the Application for Resident Space Object Proximity Analysis and IMAging (ARAPAIMA) proximity operations mission. The satellite is equipped with a cold gas propulsion system capable of exerting 2.5 mN m torques in both directions about each body axis. The attitude sensors include an angular rate gyro and star tracker (STR), supplemented by the payload optical …

Discrete-Time Neural Network Based State Observer With Neural Network Based Control Formulation For A Class Of Systems With Unmatched Uncertainties, Jason Michael Stumfoll

Masters Theses

"An observer is a dynamic system that estimates the state variables of another system using noisy measurements, either to estimate unmeasurable states, or to improve the accuracy of the state measurements. The Modified State Observer (MSO) is a technique that uses a standard observer structure modified to include a neural network to estimate system states as well as system uncertainty. It has been used in orbit uncertainty estimation and atmospheric reentry uncertainty estimation problems to correctly estimate unmodeled system dynamics. A form of the MSO has been used to control a nonlinear electrohydraulic system with parameter uncertainty using a simplified …

Modeling, Dynamics And Control Of Spacecraft Relative Motion In A Perturbed Keplerian Orbit, Mohamed Okasha, Brett Newman

Mechanical & Aerospace Engineering Faculty Publications

The dynamics of relative motion in a perturbed orbital environment are exploited based on Gauss' and Cowell's variational equations. The inertial coordinate frame and relative coordinate frame (Hill frame) are used, and a linear high fidelity model is developed to describe the relative motion. This model takes into account the primary gravitational and atmospheric drag perturbations. Then, this model is used in the design of a navigation, guidance, and control system of a chaser vehicle to approach towards and to depart from a target vehicle in proximity operations. Relative navigation uses an extended Kalman filter based on this relative model …

Control Of A Spacecraft Using Mixed Momentum Exchange Devices, Blake J. Currie

Master's Theses

Hardware configurations, a control law, and a steering law are developed for a mixed hardware spacecraft that uses both control moment gyros and reaction wheels. Replacing one or more gyros in a spacecraft with a reaction wheel has potential for cost savings while still achieving much greater performance than using reaction wheels alone. Several simulated tests are run to compare the performance to a traditional all reaction wheel or all control moment gyro spacecraft, including analysis of failure modes and singular configurations. The mixed system performed similarly to all gyro systems, responding within 6% of the gyro system’s time for …

Joint Architecture For Reusable Vehicle-Integrated Software (J.A.R.V.I.S), Anthony Mark Kane

Open Access Theses

An integrated software architecture for development of unmanned research vehicles is developed. It has been created under the premise that all unmanned vehicles require a core set of functionality that is common across platforms and that priority should be to the readability and reusability of the code base. The architecture defines the top-level system interfaces allowing internal algorithms to be manipulated without affecting the rest of the system. A robust aerospace toolbox has been developed that provides a means to rapidly prototype algorithms without the need of recreating commonly used functions or the use of expensive, proprietary software.

Feedback Speed Control Of A Small Two-Stroke Internal Combustion Engine That Propels An Unmanned Aerial Vehicle, Paul D. Fjare

UNLV Theses, Dissertations, Professional Papers, and Capstones

Unmanned aerial vehicles (UAV) require intelligent control of their power source. Small UAV are typically powered by electric motors or small two-stroke internal combustion (IC) engines. Small IC engines allow for longer flight times but are more difficult to control and cause significant ground noise. A hybrid operation that uses the engine at high altitudes and the electric motors at low altitudes is desired. This would allow for extended flight with acceptable ground noise levels. Since the engine can not be restarted in the air it must be able to remain at idle for an extended time without stalling. A …

Modification Of The Cal Poly Spacecraft Simulator System For Robust Control Law Verification, Tomoyuki Kato

Master's Theses

The Cal Poly Spacecraft Dynamics Simulator, also known as the Pyramidal Reaction Wheel Platform (PRWP), is an air-bearing four reaction wheel spacecraft simulator designed to simulate the low-gravity, frictionless condition of the space environment and to test and validate spacecraft attitude control hardware and control laws through real-time motion tests. The PRWP system was modified to the new Mk.III configuration, which adopted the MATLAB xPC kernel for better real-time hardware control. Also the Litton LN-200 IMU was integrated onto the PRWP and replaced the previous attitude sensor. Through the comparison of various control laws through motion tests the Mk.III configuration …

Observability And Confidence Of Stability And Control Derivatives Determined In Real Time, Alfonso Noriega

Doctoral Dissertations and Master's Theses

Stability and control derivatives of an aircraft were estimated from real flight test data in real time. A higher language block diagram library was developed for this purpose. Parameter identification techniques and requirements were used to detect and rate maneuvers present in the data. These ratings were used to blend newly calculated derivatives with previously known values by means of a Kalman filter. The Kalman filter output was used to identify the health of control surfaces actuators. Statistical and measured data were used to predict the probability that an actuator failure has occurred at any given time during the flight. …

Adaptive Nonlinear Control For Autonomous Ground Vehicles, William Spencer Black

Open Access Theses

We present the background and motivation for ground vehicle autonomy, and focus on uses for space-exploration. Using a simple design example of an autonomous ground vehicle we derive the equations of motion. After providing the mathematical background for nonlinear systems and control we present two common methods for exactly linearizing nonlinear systems, feedback linearization and backstepping. We use these in combination with three adaptive control methods: model reference adaptive control, adaptive sliding mode control, and extremum-seeking model reference adaptive control. We show the performances of each combination through several simulation results. We then consider disturbances in the system, and design …

Dynamics And Control Of Higher-Order Nonholonomic Systems, Jaime Rubio HerváS

Doctoral Dissertations and Master's Theses

A theoretical framework is established for the control of higher-order nonholonomic systems, defined as systems that satisfy higher-order nonintegrable constraints. A model for such systems is developed in terms of differential-algebraic equations defined on a higher-order tangent bundle. A number of control-theoretic properties such as nonintegrability, controllability, and stabilizability are presented. Higher-order nonholonomic systems are shown to be strongly accessible and, under certain conditions, small time locally controllable at any equilibrium. There are important examples of higher-order nonholonomic systems that are asymptotically stabilizable via smooth feedback, including space vehicles with multiple slosh modes and Prismatic-Prismatic-Revolute (PPR) robots moving open liquid …

Instrumentation, Control And Torch Ignition Systems Development For Lox/Methane Propulsion Research, Jesus Betancourt-Roque

Open Access Theses & Dissertations

A liquid propulsion research facility has been developed at the Center for Space Exploration Technology Research at The University of Texas at El Paso. This facility has capabilities for producing up to 25 liters of Liquid Methane, feeding LOX/Methane propellants to 100 N class thrusters and conducting automated steady state and pulsing combustion experiments. This work describes the design, development and testing process of the Data Acquisition and Remote Control System developed to integrate an Altitude Simulation System, a Cryogenic Delivery System, and multiple rocket combustors and thrusters. A Torch Ignition System development is detailed as well as the evaluation …

Determination Of Stability And Control Derivatives For A Modern Light Composite Twin Engine Airplane, Monica M. Londono

Master's Theses - Daytona Beach

To develop and compare full envelope stability and control derivatives and their associated errors for a modern light composite twin engine airplane from flight test data and digital DATCOM (Data Compendium). This development is to serve three purposes 1) to provide data for validation of newer analytical techniques such as Computational Fluid Dynamics (CFD), 2) to provide public domain static and dynamic stability and control derivatives for a modern twin engine airplane, 3) to analyze the relationship between test design and error for both output error and equation error methods.

A flight test program was conducted on a Diamond Twin …

Mitigating Crack Propagation In A Highly Maneuverable Flight Vehicle Using Life Extending Control Logic, Mohamed Mostafa Yousef Bassyouny Elshabasy

Mechanical & Aerospace Engineering Theses & Dissertations

In this research, life extending control logic is proposed to reduce the cost of treating the aging problem of military aircraft structures and to avoid catastrophic failures and fatal accidents due to undetected cracks in the airframe components. The life extending control logic is based on load tailoring to facilitate a desired stress sequence that prolongs the structural life of the cracked airframe components by exploiting certain nonlinear crack retardation phenomena. The load is tailored to include infrequent injections of a single-cycle overload or a single-cycle overload and underload. These irregular loadings have an anti-intuitive but beneficial effect, which has …

Robust Control Techniques Enabling Duty Cycle Experiments Utilizing A 6-Dof Crewstation Motion Base, A Full Scale Combat Hybrid Electric Power System, And Long Distance Internet Communications, Marc Compere, Jarrett Goodell, Miguel Simon, Wilford Smith, Mark Brudnak

Publications

The RemoteLink effort supports the U.S. Army's objective for developing and fielding next generation hybrid-electric combat vehicles. It is a distributed soldierin- the-Ioop and hardware-in-the-Ioop environment with a 6-DOF motion base for operator realism, a full-scale combat hybrid electric power system, and an operational context provided by OneSAF. The driver/gunner crewstations rest on one of two 6-DOF motion bases at the U.S. Army TARDEC Simulation Laboratory (TSL). The hybrid power system is located 2,450 miles away at the TARDEC Power and Energy System Integration Laboratory (P&E SIL). The primary technical challenge in the RemoteLink is to operate both laboratories together …

Effect Of Operator Control Configuration On Unmanned Aerial System Trainability, John Neumann

Electronic Theses and Dissertations

Unmanned aerial systems (UAS) carry no pilot on board, yet they still require live operators to handle critical functions such as mission planning and execution. Humans also interpret the sensor information provided by these platforms. This applies to all classes of unmanned aerial vehicles (UAV's), including the smaller portable systems used for gathering real-time reconnaissance during military operations in urban terrain. The need to quickly and reliably train soldiers to control small UAS operations demands that the human-system interface be intuitive and easy to master. In this study, participants completed a series of tests of spatial ability and were then …

Robust Control Techniques For State Tracking In The Presence Of Variable Time Delays, Jarrett Goodell, Marc Compere, Miguel Simon, Wilford Smith, Ronnie Wright, Mark Brudnak

Publications

In this paper, a distributed driver-in-the-Ioop and hardware-in-the-Ioop simulator is described with a driver on a motion simulator at the U.S. Army TARDEC Ground Vehicle Simulation Laboratory (GVSL). Realistic power system response is achieved by linking the driver in the GVSL with a full-sized hybrid electric power system located 2,450 miles away at the TARDEC Power and Energy Systems Integration Laboratory (P&E SIL), which is developed and maintained by Science Applications International Corporation (SAIC). The goal is to close the loop between the GVSL and P&E SIL over the Internet to provide a realistic driving experience in addition to realistic …

Optimization Of Torquer Coil Design For Use With The Small Satellite Attitude Control Simulator, David Deloyd Anderson

Undergraduate Honors Capstone Projects

This paper presents a procedure used to optimize the performance of a ferromagnetic core magnetic torquer coil design for use on the Space Dynamics Laboratory (Logan, UT) Small Satellite Attitude Control Simulator. The items of optimization include the primary goal of maximizing the coil 's magnetic moment while reducing power consumption and system mass within given power, mass, and dimensional constraints. The optimization process makes use of several simple equations to determine a few starting points for design, after which an iterative approach based on experimentation is used to produce the final design. It is found that optimal magnetic moment …

Integrated Control Of Thermally Distorted Large Space Antennas, Robert H. Tolson

Mechanical & Aerospace Engineering Theses & Dissertations

Studies on controlling the thermal distortion of large space antennae have generally investigated a single orbital position and have optimized actuator locations based on minimizing the RMS surface deviation from the original parabolic shape. One study showed the benefits of directly using far zone electric field characteristics as the performance measure; but, this approach resulted in a nonlinear programming problem. The objective of the current study is to develop an approach to designing a control system that (1) recognizes the time dependence of the distortion and (2) controls variables that are directly related to far field performance in a quadratic …