Aerospace Engineering Commons^™

Development Of An Analysis And Design Optimization Framework For Marine Propellers, Ashish C. Tamhane

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, a framework for the analysis and design optimization of ship propellers is developed. This framework can be utilized as an efficient synthesis tool in order to determine the main geometric characteristics of the propeller but also to provide the designer with the capability to optimize the shape of the blade sections based on their specific criteria.

A hybrid lifting-line method with lifting-surface corrections to account for the three-dimensional flow effects has been developed. The prediction of the correction factors is achieved using Artificial Neural Networks and Support Vector Regression. This approach results in increased approximation accuracy compared …

Optimization Of Water And Energy Use In Indirect Evaporative Cooling System By Cfd, Mansi Vijay Prajapati

Mechanical and Aerospace Engineering Theses - Archive

Data center cooling is becoming important to maintain environmental condition for ITE- Information technology equipment. Conventional evaporative wet cooling media lowers the temperature of the dry bulb temperature of incoming air in which heat transfer to water film and sensibly cool the product air by increasing moisture into air. Wet cooling media technique requires large quantity of clean water, which is reducing area where water is very less. Therefore, indirect evaporative cooling is good alternative. Chiller plants/Indirect Evaporative cooling(IEC) are used as a cooling source for larger data centers as they are more efficient in heat transfer without adding moisture …

Computational Fluid Dynamics Is Key To Better Flying Aircraft, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Maximizing Use Of Air-Side Economization, Direct And Indirect Evaporative Cooling For Energy Efficient Data Centers, Betsegaw Kebede Gebrehiwot

Mechanical and Aerospace Engineering Dissertations - Archive

Data centers house information technology (IT) equipment such as servers and network switches which are vital for our networked modern society by providing digital data storage, data processing and connectivity. Data centers house few hundreds to tens of thousands of IT equipment that consume few kilowatt-hours to multi-megawatt-hours of electrical energy that gets dissipated as heat. IT equipment need to be properly cooled so that they operate reliably for their expected lifetime. For air cooled IT equipment, manufacturers provide heat sinks, cold plates, fans, et cetera to remove heat from the vicinity of heat dissipating components and data centers need …

Cfd Modelling Of Wet Cooling Media And Design Optimization Of Heat Sink For Data Center Application, Shivang Yogeshkumar Desai

Mechanical and Aerospace Engineering Theses - Archive

Air cooling is most widely used and economical method of currently available cooling technologies in which heat exchanger plays a vital role in facility designs. Evaporative cooling can be energy efficient than mechanical cooling because it uses water’s enthalpy of vaporization. Wet cooling pads can be used as the direct evaporative cooling system in which pad is made of cellulose fibers those gets wet when water injected. When hot and dry air passes through pad surfaces, water evaporates in the air which cools down air adiabatically increasing humidity. These type of cooling units can be installed in these type of …

Design Consideration And Steady State Study Of Thrust Bearings In High Speed Subsonic Applications, Arvind Prabhakar

Mechanical and Aerospace Engineering Theses - Archive

Thrust bearings are required to perform at high speeds in various turbomachinery applications causing the nature of fluid flow within the bearings to be in high subsonic as well as supersonic regimes. The motivation of this research is to develop a bearing performance prediction model tailored for high subsonic speeds and large Reynolds numbers. The prime fluid characteristics studied in the thin film for predicting the bearing performance has been achieved by carefully considering inertial, viscous as well as compressible effects within the thin film fluid flow. Fluid inertia is a vital physical phenomenon that plays an important role in …

Computational Study And Error Analysis Of An Integrated Sampling-Probe And Gas-Analyzer For Mixing Measurements In Supersonic Flows, Wenbo Zhu

Mechanical and Aerospace Engineering Theses - Archive

Concentration probes are employed in supersonic flow mixing experiments for binary gas mixture composition measurements. These measurements are fundamental for the advancement of the scramjet technology. While non-intrusive laser-based methods (such as planar laser-induced fluorescence and filtered Rayleigh scattering) have been developed greatly over the past few decades, intrusive methods (such as concentration probes) still play an essential role in the measurement of mixture composition due to the fact that, with correct application, they do not require further assumptions on the aerothermodynamic states of the investigated mixture, which are often difficult to corroborate. Conversely, such assumptions are essential to the …

Cfd Analysis Of Vapor Chamber With Micro Pillars As Heat Spreader For High Power Electronic Devices, Yasir Aziz Modak

Mechanical and Aerospace Engineering Theses - Archive

The recent trend in electronic industry shows that there is large power dissipation from the electronic devices and at the same time their sizes are getting smaller. This large power dissipation takes place in the form of releasing heat energy. It is observed that heat dissipation from the electronic devices is high and source size is small. The high device temperatures result in decreased reliability and increased failure rates. This difficulty can be addressed by controlling the temperatures at the source of heat generation. In chip scale package chip is the major source of heat generation. Thus our priority is …

Performance Evaluation Of Plate-Fin And Pin-Fin Heat Sinks For The Application Of Oil Immersion Cooling And Design Optimization Of Dynamic Cold Plate For The Application Of Warm Water Cooling, Parth Jayeshkumar Soni

Mechanical and Aerospace Engineering Theses - Archive

In IT industries, to keep server rooms and data centers cool is a constant challenge for hardware developers and the cooling solution providers. Air cooling is the most widely used approach for thermal management of servers in data centers from many years. However, the scenario is changing gradually as the computational ability of data center is increasing exponentially. Because of increasing computational ability, the heat generated by the servers is increased in such amount that air cooling is not as efficient as it was before. Hence, alternative cooling system is required. In 1970’s the idea of liquid cooling was introduced. …

Development Of A Three-Dimensional High-Order Strand-Grids Approach, Oisin Tong

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The strand-Cartesian grid approach is a unique method of generating and computing fluid dynamic simulations. The strand-Cartesian approach provides highly desirable qualities of fully-automatic grid generation and high accuracy. This work focuses on development of a high-accuracy methodology (high-order scheme) on strand grids for two and three dimensions.

In this work, the high-order scheme is extended to high-Reynolds number computations in both two and three dimensions with the Spalart-Allmaras turbulence model and the Menter SST turbulence model. In addition, a simple limiter is explored to allow the high-order scheme to accurately predict discontinuous flows.

Extensive verification and validation is conducted …

Analysis Of Road Vehicle Aerodynamics With Computational Fluid Dynamics, Christian Armando Mata

Open Access Theses & Dissertations

A road vehicles aerodynamics can be one of the most influential aspects of its performance. With the increased importance on fuel efficiency in recent years, new road vehicles are being developed smaller in size, with smaller displacement engines, as well as with improved aerodynamics. The aerodynamics of a vehicle can have a significant effect on its fuel efficiency, as well as other important aspects of the vehicles performance such as the top speed, acceleration, and handling. A study focusing on analyzing aerodynamic effects due to vehicle geometries such as wheels covered by the vehicles body in comparison to open wheels …

Parametric Study Of An Igbt Cold Plate And Affect Of Device Level Modelling On System Level Thermal Predictions, Abhishek Raj Urs Kadaba Nagaraja Urs

Mechanical and Aerospace Engineering Theses - Archive

In power electronics, as there is continuous increase in performance of the electronic devices, simultaneously the size of the components used in these devices keep on decreasing. This has resulted in increased power densities and the requirements for excellent cooling as well in order to avoid the failure of those devices. Traditionally, while designing a cooling system for a device, uniform heat flux is assumed throughout the components. In many cases this method may not be accurate for a particular model design. There are chances that the heat flux distribution around the components are non-uniform and requires a more accurate …

The Effects Of Simplifications On Isolated Wheel Aerodynamics, Sammy Diasinos, Tracie Barber, Graham Doig

Aerospace Engineering

In order to study the aerodynamic forces and flow features of rotating wheels, compromises and simplifications are often made in wind tunnel testing, and more frequently so in numerical modelling. A CFD approach similar to that commonly used in industry was utilised to investigate common assumptions involving; the influence of geometric fidelity in wheel hub regions, ground representation, the modelling of the contact patch, and the effects of rotation on separation. It was found that the separation and wake characteristics were strongly influenced by the rotation of the wheel; the separation point changed by as much as 90% compared to …

Development Of Cpanel, An Unstructured Panel Code, Using A Modified Tls Velocity Formulation, Christopher R. Satterwhite

Master's Theses

The use of panel codes in the aerospace industry dates back many decades. Recent advances in computer capability have allowed them to evolve, both in speed and complexity, to provide very quick solutions to complex flow fields. By only requiring surface discretization, panel codes offer a faster alternative to volume based methods, delivering a solution in minutes, as opposed to hours or days. Despite their utility, the availability of these codes is very limited due to either cost, or rights restrictions.

This work incorporates modern software development practices, such as unit level testing and version control, into the development of …

Application Of Wray-Agarwal Model To Turbulent Flow In A 2d Lid-Driven Cavity And A 3d Lid-Driven Box, Hakop J. Nagapetyan

McKelvey School of Engineering Graduate Student Theses & Dissertations

In this thesis, various turbulence models are used for simulating internal vortical flow, both turbulent and laminar, with large recirculation by considering the flow in a 2-D lid-driven square cavity and a 3-D lid driven cubic box. The accuracy of the newly developed Wray-Agarwal (WA) one equation turbulence model is compared against two well-known industry standard turbulence models; the Spalart-Allmaras (SA) and the Shear-Stress-Transport (SST) k-ω models. The simulations are performed by numerically solving the Reynolds-Averaged Navier-Stokes (RANS) equations in conjunction with WA, SA and SST k-ω models and comparing the results with the available experimental data and Large Eddy …

Similarity Analysis Of A Swirling Counter-Flow, Jitesh Rane

Doctoral Dissertations and Master's Theses

Swirling counter-flows are used in numerous engineering applications, like combustion, heat exchangers, cyclonic separation and mixing, etc. These swirling counter-flows produce complex flow fields. It is important to study these types of flows in order to use them properly in many applications.

The present work provides insight into the flowfield inside a swirling counter-flow when the fluid is injected tangentially in a cylindrical container. A semi-analytical solution is developed by starting with the full Navier-Stokes equation and using a similarity analysis. A decaying swirl along the axis of the cylinder is assumed, which reduces the Navier-Stokes equations to first order …

Validation Of A Cfd Approach For Gas Turbine Internal Cooling Passage Heat Transfer Prediction, Daniel G. Wilde

Master's Theses

This report describes the development and application of a validated Computational Fluid Dynamics (CFD) modelling approach for internal cooling passages in rotating turbomachinery. A CFD Modelling approach and accompanying assumptions are tuned and validated against academically available experimental results for various serpentine passages. Criteria of the CFD modelling approach selected for investigation into advanced internal cooling flows include accuracy, robustness, industry familiarity, and computational cost.

Experimental data from NASA HOST (HOt Section Technology), Texas A&M, and University of Manchester tests are compared to RANS CFD results generated using Fluent v14.5 in order to benchmark a CFD modelling approach.

Capability of …

Design Of A High Intensity Turbulent Combustion System, Mohammad Arif Hossain

Open Access Theses & Dissertations

In order to design next generation gas turbine combustor and rocket engines, a systematic study of flame structure at high intensity turbulent flow is necessary. The fundamental study of turbulent premixed combustion has been a major research concern for decades. The work is focused on the design and development of a high intensity turbulent combustion system which can be operated at compressible (0.3 < M < 0.5), preheated (T0=500K) and premixed conditions in order to investigate the 'Thickened Flame' regime. An air-methane mixture has been used as the fuel for this study. An optically accessible backward-facing step stabilized combustor has been designed for a maximum operating pressure of 6 bar. A grid has been introduced with different blockage ratios (BR = 54%, 61% & 67%) in order to generate turbulence inside the combustor for the experiment. Optical access is provided via quartz windows on three sides of the combustion chamber. Finite Element Analysis (FEA) is done in order to verify the structural integrity of the combustor at rated conditions. In order to increase the inlet temperature of the air, a heating section was designed to use commercially available in-line heaters. Separate cooling subsystems have been designed for chamber cooling and exhaust cooling. The LabVIEW software interface has been selected as the control mechanism for the experimental setup. A 10 kHz Time Resolved Particle Image Velocimetry (TR-PIV) system and a 3 kHz Planer Laser Induced Fluorescence (PLIF) system have been integrated with the system in order to diagnose the flow field and the flame respectively. The primary understanding of the flow field inside the combustor was achieved through the use of Detached Eddy Simulation (DES) by using commercially available software package ANSYS FLUENT. Preliminary validation is done by 10 kHz TR-PIV technique. Both qualitative and quantitative analysis have been done for CFD and experiment. Major flow parameters such as average velocity, fluctuation of velocity, kinetic energy, and turbulent intensity have been calculated for two distinct Reynolds number (Re = 815 & 3500). PIV results are compared with CFD results which show significant agreement with each other.

High Temperature Flow Solver For Aerothermodynamics Problems, Huaibao Zhang

Theses and Dissertations--Mechanical and Aerospace Engineering

A weakly ionized hypersonic flow solver for the simulation of reentry flow is firstly developed at the University of Kentucky. This code is the fluid dynamics module of known as Kentucky Aerothermodynamics and Thermal Response System (KATS). The solver uses a second-order finite volume approach to solve the laminar Navier– Stokes equations, species mass conservation and energy balance equations for flow in chemical and thermal non-equilibrium state, and a fully implicit first-order backward Euler method for the time integration. The hypersonic flow solver is then extended to account for very low Mach number flow using the preconditioning and switch of …

A Cfd Investigation Of The Hydrodynamic Characteristics Of Fluid Flow Through An Impeller And Multi-Objective Design Optimization Of A Centrifugal Pump, Mohammed Khammat Sagban

Doctoral Dissertations and Master's Theses

In this thesis, the first part is conducting an investigation of the hydrodynamic characteristics (pressure and velocity) of fluid flow (water) through an impeller of a centrifugal pump. To illustrate a one-dimensional model is used to identify an impeller of a GDM 10 x 12 HD centrifugal pump using Vista CPD design and BladeGen tool. A three-dimensional model is then built with a commercial software package ANSYS Blade Modeler. The structured mesh of the impeller blade is obtained by using TurboGrid system. The volute of the centrifugal pump is built in ANSYS geometry, and an unstructured mesh is accomplished by …

Evaluation Of The Performance Of Various Turbulence Models For Accurate Numerical Simulation Of A 2d Slot Nozzle Ejector, Colin Graham

McKelvey School of Engineering Graduate Student Theses & Dissertations

With the development over the last several decades, accurate Computational Fluid Dynamics (CFD) modeling has now become an essential part in the analysis and design of various industrial products where the fluid flow plays an important role. The goal of this thesis is to apply the CFD technology to the analysis of a 2D slot nozzle ejector which has application in Short Take-off and Landing (STOL) aircraft and other future aerospace vehicles. In the nozzle-ejector configuration, the high speed air flow from the nozzle entrains the ambient air into a mixing chamber (ejector) as a means to create additional thrust …

Effects Of Crossflow In An Internal-Cooling Channel On Film Cooling Of A Flat Plate Through Compound-Angle Holes, Zachary Taylor Stratton

Open Access Theses

The film-cooling holes in turbine blades are fed from an internal cooling channel. This channel imposes a crossflow at the entrance of the holes that can significantly affect the performance of the cooling jets that emanate from those holes. In this study, CFD simulations based on steady RANS with the shear-stress transport (SST) and the realizable k -ε turbulence models were performed to study film cooling of a flat plate with cooling jets issuing from eight round holes with a compound angle of 45 degrees, where the coolant channel that fed the cooling jets was oriented perpendicular to the direction …

Flight And Stability Of A Laser Inertial Fusion Energy Target In The Drift Region Between Injection And The Reaction Chamber With Computational Fluid Dynamics, Tiffany Leilani Mitori

Master's Theses

A Laser Inertial Fusion Energy (LIFE) target’s flight through a low Reynolds number and high Mach number regime was analyzed with computational fluid dynamics software. This regime consisted of xenon gas at 1,050 K and approximately 6,670 Pa. Simulations with similar flow conditions were performed over a sphere and compared with experimental data and published correlations for validation purposes. Transient considerations of the developing flow around the target were explored. Simulations of the target at different velocities were used to determine correlations for the drag coefficient and Nusselt number as functions of the Reynolds number. Simulations with different target angles …

Characterizing Cryogenic Propellant Flow Behavior Through A Cavitating Venturi In Comparison To Alternative Flow Control Mechanisms, Marjorie Adele Ingle

Open Access Theses & Dissertations

The work detailed is an investigation of the use of a cavitating venturi as both a flow control and metering device. This was achieved through the combination of actual experimentation and numerical modeling of the fluid behavior of both liquid water and liquid methane as it passes through the test article designed, developed, and validated here within this study. The discharge coefficient of the cavitating venturi was determined through weigh flow calibration testing to determine an average mass flow rate. Turbine flow meter flow rate readings were used as a point of comparison and the discharge coefficient was computed. The …

Computational And Experimental Comparison Of A Powered Lift, Upper Surface Blowing Configuration, Jay M. Marcos

Master's Theses

In the past, 2D CFD analysis of Circulation Control technology have shown poor comparison with experimental results. In Circulation Control experiments, typical results show a relationship between lift coefficient, CL, vs blowing momentum coefficient, Cμ. CFD analysis tend to over-predict values of CL due to gridding issues and/or turbulence model selection. This thesis attempted to address both issues by performing Richardson’s Extrpolation method to determine an acceptable mesh size and by using FLUENT’s 2-equation turbulence models. The experimental results and CAD geometry were obtained from Georgia Tech Research Institute for comparison with the CFD analysis.

The study showed that 3D …

Development Of Cfd Models For The Purposes Of Exploring Free Surface Wave Phenomena, Leonard P. Stoehr

Masters Theses

With the push for finding alternative, green energy sources, the harnessing of energy from ocean and lake waves is becoming a more researched field. To fully understand the behavior of wave interactions and optimize designs to extract this energy, it is necessary to develop computer models that can accurately replicate this behavior. A case is presented in which previous work done using the wave tank found in the Western Michigan University fluids lab is examined. The case involves harnessing the energy generated by ocean waves through the usage of plates of different shapes resting horizontally on the water’s surface. The …

Design And Performance Of Circulation Control Geometries, Rory Martin Golden

Master's Theses

With the pursuit of more advanced and environmentally-friendly technologies of today’s society, the airline industry has been pushed further to investigate solutions that will reduce airport noise and congestion, cut down on emissions, and improve the overall performance of aircraft. These items directly influence airport size (runway length), flight patterns in the community surrounding the airport, cruise speed, and many other aircraft design considerations which are setting the requirements for next generation aircraft. Leading the research in this movement is NASA, which has set specific goals for the next generation regional airliners and has categorized the designs that meet the …

Computational Analysis Of A Wing Oscillator, Ryne Derrick Radermacher

Masters Theses

An analysis of a newly proposed wind power extraction device called a wing oscillator was performed using computational fluid dynamics (CFD). A wing oscillator is a device that consists of two airfoils attached to a central pivot by means of a frame or shaft. Oscillatory motion is produced by controlling the angle of attack of the airfoils as a fluid flow is passed over the device. A robust mathematical scheme was developed to investigate the performance of the wing oscillator and was hooked to the CFD software package FLUENT through User Defined Functions (UDFs). Using the dynamic meshing analysis methods …

3d Cfd On An Open Wheel Race Car Front Wing In Ground Effects, Thomas A. Price

Aerospace Engineering

The purpose of the report is to investigate the ability of the Fluent 6.3 k-ε Realizable turbulence model with standard wall functions to model the flow around the front wing of Cal Poly’s 2008 Formula SAE car. The three primary areas of interest are ground effects, the wing wheel interaction, and the wing tip vortices. Fluent was successful at modeling the increase suction from the ground effects, and the upwash due to the wing tip vortices. The results also displayed how the high pressure region in front of the tire propagates forward and interacts with the pressure distribution around the …

Numerical Modeling Of The Cn Spectral Emission Of The Stardust Re-Entry Vehicle, Alexandre Martin, Erin D. Farbar, Iain D. Boyd

Mechanical Engineering Faculty Publications

Re-entry vehicles designed for space exploration are usually equipped with thermal protection systems made of ablative material. In order to properly model and predict the aerothermal environment of the vehicle, it is imperative to account for the gases produced by ablation processes. In the case of charring ablators, where an inner resin is pyrolyzed at a relatively low temperature, the composition of the gas expelled into the boundary layer is complex and may lead to thermal chemical reactions that cannot be captured with simple ow chemistry models. In order to obtain better predictions, an appropriate gas ow chemistry model needs …