Aerospace Engineering Commons^™

Small Satellite Earth-To-Moon Direct Transfer Trajectories Using The Cr3bp, Garrett Levi Mcmillan

Masters Theses

"The CubeSat/small satellite field is one of the fastest growing means of space exploration, with applications continuing to expand for component development, communication, and scientific research. This thesis study focuses on establishing suitable small satellite Earth-to-Moon direct-transfer trajectories, providing a baseline understanding of their propulsive demands, determining currently available off-the-shelf propulsive technology capable of meeting these demands, as well as demonstrating the effectiveness of the Circular Restricted Three Body Problem (CR3BP) for preliminary mission design. Using the CR3BP and derived requirements from NASA's Cube Quest Challenge, five different trajectory scenarios were analyzed for their propulsive requirements. Results indicate that the …

Landing-Gear Impact Response: A Non-Linear Finite Element Approach, Tuan H. Tran

UNF Graduate Theses and Dissertations

The primary objective of this research is to formulate a methodology of assessing the maximum impact loading condition that will incur onto an aircraft’s landing gear system via Finite Element Analysis (FEA) and appropriately determining its corresponding structural and impact responses to minimize potential design failures during hard landing (abnormal impact) and shock absorption testing. Both static and dynamic loading condition were closely analyzed, compared, and derived through the Federal Aviation Administration’s (FAA) airworthiness regulations and empirical testing data.

In this research, a nonlinear transient dynamic analysis is developed and established via NASTRAN advanced nonlinear finite element model (FEM) to …

Laser Machining Countersinks In Carbon Fiber Reinforced Polymer, Leon James Neely Hill

Masters Theses

“Laser machining countersinks with a frequency doubled Q-switched diode pumped Nd:YAG laser is demonstrated. Tests were conducted in 0.100" thick IM7 prepreg CFRP with [0,90]3S orientation. The HAZ is minimized to avoid stress concentrations in the epoxy matrix. A chamber and filtration system was designed and built to contain the byproducts produced in the machining process. The variables investigated are the number of repetitions in the offset path, the plunge rate, and the line energy. The research was performed over one baseline study, one parameter space exercise, two full factorial experiments, and one repeatability study. Assessment was done under an …

A Systems And Cost Analysis Of Human Rated Mars Entry, Descent, And Landing Vehicles, Paul Daniel Friz

Doctoral Dissertations

"Cost is one of the biggest obstacles to sending humans to Mars. However, spacecraft costs are typically not taken into consideration until after the preliminary vehicle and mission concepts have been designed. Once costs have been estimated, managers and project teams often lack confidence that the final cost of the mission will match the preliminary estimates. The present work provides a robust methodology for using cost as a valid metric early in the design phase of future human Mars Entry, Descent, and Landing (EDL) vehicles. This is done in three parts. First, state of the art parametric costing methods are …

Study Of Optical Propulsion Concepts And Techniques For Small-Satellites, Jaykob Neil Maser

Doctoral Dissertations

"The first objective of this research is to manufacture and investigate the characteristics and use of asymmetric, metallic, nanostructures for plasmonic force propulsion, a developing method of nano-/picosatellite thrust generation. This project developed a higher-fidelity model of a recently envisioned small spacecraft propulsion system for precision pointing and proximity control. Plasmonic force propulsion harnesses solar light focused onto plasmon reactive sub-wavelength nanostructures to generate polarized oscillations of electrons on the surface of metallic nanostructures which accelerate and expel nanoparticle propellant via strong optical forces. This research also explores how material selection affects the electromagnetic response of the closely positioned asymmetric …

Atomistic Simulations Of Nanoindentation Response Of Irradiation Defects In Iron, M. Mustafa Azeem, Qingyu Wang, Muhammad Zubair

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Radiation response of a material is a consequence of defects' evolution in any radiation damage event. The radiation-induced defects can significantly alter the mechanical properties of a material. Radiation damage initiates from incident neutron by bombardment on solid material causing production and evolution of Frenkel defects. Since voids are formed due to aggregation of a large number of vacancies that cause dimensional changes and hence irradiation-induced swelling. In order to characterize the effect of irradiation defects, we have performed molecular dynamics (MD) simulations to investigate nanoindentation response of point defects and voids in Fe and their effects on mechanical parameters. …

Uas Flight Operations In Complex Terrain: Assessing The Agricultural Impact From Hurricane Maria In The Central Mountainous Region Of Puerto Rico, Kevin Adkins

Publications

Hurricane Maria struck Puerto Rico in September 2017 as a Category 4 storm causing major damage to infrastructure, agriculture and natural ecosystems, as well as the loss of many lives. Among the crops hardest hit was coffee, one of the most important crops in Puerto Rico. As a perennial system, coffee takes various production forms along a gradient from high shade/biodiversity coffee farms to low shade coffee monocultures and therefore offers an ideal means for the study of resistance and resilience of an agroecosystem to weather and climate disturbance. During the summer of 2018, 14 impacted farms across the production …

Traditional Vs Gesture Based Uav Control, Sam J. Holley, Brian Sanders, Dennis Vincenzi, Yuzhong Shen

Publications

Abstract. The purpose of this investigation was to assess user preferences for controlling an autonomous system. A comparison using a virtual environment (VE) was made between a joystick based, game controller and a gesture-based system using the leap motion controller. Command functions included basic flight maneuvers and switching between the operator and drone view. Comparisons were made between the control approaches using a representative quadcopter drone. The VE was designed to minimize the cognitive loading and focus on the flight control. It is a physics-based flight simulator built in Unity3D. Participants first spend time familiarizing themselves with the basic controls …