Aerospace Engineering Commons^™

Sensors Location Effect On The Dynamic Behaviour Of The Composite Structure With Flaw Detection, Eltahry Elghandour, Faysal Kolkailah, Abdel- Hamid I. Mourad

Aerospace Engineering

In this paper presents an experimental and numerical investigation ofthe natural frequency of composite material cantilever plates. The stacking sequence of tbe composite plate is Quasi-isotropic laminated plate is [2(0j/±45°/2(90°)]" The plate was subjected to incremental cuts and tests to determine changes in new modal properties. The study included white noise and sinusoidal dynamic testing techniques and a virtual instrument dynamic analyzer. In this study also, determining the resonant frequencies of the undamaged and damaged plate, and evaluating the capabilities of piezoelectric ceramics (PZT's) for fault detection based on their sensitivity and accuracy changes in modal parameters. Numerical results are …

Mixed Mode Stable Crack Extensions Through Stiffened Specimens, Abdel-Hamid I. Mourad, Eltahry Elghandour, Faysal A. Kolkailah

Aerospace Engineering

This study presents an experimental investigation of fracture mechanics for isotropic material, aluminum alloy D16AT. The problem of stable crack growth (SCG) has been addressed in this paper. Experimental results are presented for symmetrically stiffened and unstiffened three point bend specimens subjected to different modes, mode I and mixed mode. The stiffeners are doubly bonded to the fatigue pre-cracked specimens parallel to the length at a certain distance behind the crack tip using an adhesive Redux 410 NA. Results concerning load displacement variation, growth of plastic zones, instantaneous crack edge profiles, and tunneling are presented. There is evidence that the …

Emerald & Orion Formation Flying Experiment, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "Emerald & Orion Formation Flying Experiment" from May 5, 1999.

Solving An Inverse Control Problem Using Predictive Methods, Chad J. Davis

Theses and Dissertations

Model Predictive Control is the class of control methods that optimizes a specified performance index in order to minimize the weighted future output deviations from a setpoint trajectory. This thesis applies MPC in the inverse sense -- known aircraft outputs are applied in the performance index as setpoints in an attempt to determine what control histories caused those outputs. Using this method, aircraft mishap investigators could then have a means of determining what the control surface deflections were throughout an incident since Flight Data Recorder data does not include control surface deflections. The actual Flight Data Recorder data from aircraft …

Close Formation Flight Control, Andrew W. Proud

Theses and Dissertations

In this research the close formation flight control problem is addressed. The formation consists of a lead and wing aircraft, where the wing flies in close formation with the lead, such that the lead's vortices produce aerodynamic coupling effects, and a reduction in the formation's drag is achieved. A controller, i.e., a formation-hold autopilot for the wing aircraft, is designed such that the formation's geometry is maintained in the face of lead aircraft maneuvers. In the formation flight control system, the wing and lead aircraft dynamics are coupled due to kinematic effects, and, in the case of close formations, additional …

Variable Area Inlet For Vehicle Thermal Control, Thomas R. Layne, Milton E. Franke, Darrell B. Ridgedly

AFIT Patents

A variable area inlet structure for a vehicle utilizing ram air for coolant is described which comprises a variable area inlet device in the ram air inlet in the form of a butterfly valve, damper, shutter, or similar structure, a temperature sensor in thermal contact with a component within the vehicle to be cooled by ram air flow, a controller and actuator, responsive to the temperature sensor and operatively connected to the variable area device, for controlling the inlet area in response to the component temperature.

Student Micro/Nano Space Applications, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "Student Micro/Nano Space Applications" from April 15, 1999.

Orion Pdr: Ssdl Program Overview, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "Orion PDR SSDL Program Overview" from April 9, 1999.

Portfolio Assessment In Aerodynamics, Nikos J. Mourtos

Faculty Publications

A new way of assessing student learning in an aerodynamics course through the use of portfolios is presented. The approach is portable to any engineering course, with a few modifications depending on content. The main idea is to allow students more responsibility for their own learning. Instead of having everyone in the class perform identical activities (homework, experiments, projects, tests, etc.), a cadre of assignments is made available to them. Students choose and perform (within reason) the ones that suit them better in terms of their own strengths and learning styles. The ultimate goal is for each student to demonstrate …

The Airline Quality Rating 1999, Brent D. Bowen, Dean Headley, Uno Aviation Institute

Faculty Books and Monographs

UNOAI Report 99-3

he Airline Quality Rating (AQR) was developed and first announced in early 1991 as an objective method of comparing airline performance on combined multiple criteria. This current report, Airline Quality Rating 1999, contains monthly Airline Quality Rating scores for 1998. Additional copies are available by contacting Wichita State University or the University of Nebraska at Omaha.

The Airline Quality Rating 1999 is a summary of month-by-month quality ratings for the ten major domestic U.S. airlines operating during 1998. Using the Airline Quality Rating system of weighted averages and montly performance data in the areas of on-time arrivals, …

Optimization Of A Vortex Generator Configuration For A 1/4-Scale Piper Cherokee Wing, Kerri A. Raykowski

Master's Theses - Daytona Beach

Several sets of wind tunnel tests were performed to determine an optimum vortex generator configuration for a 1/4-scale model of the Piper Cherokee wing. Several variables were incorporated into this experiment in an effort to determine their influence on vortex generator performance enhancement (or degradation). Vane type vortex generators were used with 3 different leading edge sweeps: zero (rectangular planform), 20, and 45 degrees. Three different vortex generator heights were tested (0.05”, 0.1”, and 0.2”) to find the optimal vortex generator height relative to the local boundary layer thickness. The vortex generator angle of incidence relative to the freestream was …

Reduction Of Helmet Buffeting In Open Cockpit, Single Seat Race Cars, Mark Vallon

Master's Theses - Daytona Beach

At speeds approaching 240 mph, drivers of open cockpit race cars frequently experience large aerodynamic forces which act on the helmet. These forces, specifically the aerodynamic buffeting of the helmet, reach levels which are very fatiguing and distracting to the driver, and are therefore unacceptable. Little investigation has been done in this area, because normal wind tunnel tests do not isolate the helmet from the rest of the car. During this project, measurements of aerodynamic forces acting on a helmet inside a race car cockpit were made to determine the cause of the buffeting, and to determine possible improvements.

Tests …

Assessment Of A Higher Harmonic Control System For Minimizing Vibrations On A Dynamically Scaled Tiltrotor Model, David J. Piatak

Mechanical & Aerospace Engineering Theses & Dissertations

The performance of a higher harmonic control system called the Multipoint Adaptive Vibration Suppression System (MA VSS) at reducing 3/rev wing vibratory loads and fuselage vibrations on a dynamically-scaled tiltrotor model is presented. Previous wind tunnel tests on a semispan aeroelastic tiltrotor model have demonstrated the effectiveness of MAVSS for reducing wing vibratory loads using both an active flaperon and swashplate. The primary goal, however, of such a vibration suppression system is to reduce tiltrotor fuselage vibrations in order to improve passenger comfort. The present study addresses the reduction of both wing and fuselage vibrations using MA VSS active flaperons …

Stability Of Three-Dimensional Compressible Boundary-Layers, Samarasingham Jeyasingham

Mechanical & Aerospace Engineering Theses & Dissertations

The failure repair process of a continuously operating device is studied in this research. Different cases that incorporate modeling of equipment deterioration, inspection, and maintenance for optimal maintenance policy are proposed. Markov processes are used to determine state probabilities, and the optimal value of the mean time to preventive maintenance is determined by maximizing the availability of the equipment with respect to the meantime preventive maintenance. The approach uses models that assume that equipment can fail due to both deterioration and random failures. Preventive maintenance can be performed from each working state to avoid deterioration failure. Economic effects are integrated …

Aeroelastic Load Alleviation Using Shunted Piezolectrics, Anna-Maria Rivas Mcgowan

Mechanical & Aerospace Engineering Theses & Dissertations

Several analytical and experimental studies clearly demonstrate that piezoelectric materials (piezoelectrics) can be used as actuators to actively control vibratory response including aeroelastic response. However, two important issues in using piezoelectrics as actuators for active control are: 1) the potentially large amount of power required to operate the actuators, and 2) the complexities involved with active control (added hardware, control law design and implementation). Active or passive damping augmentation using shunted piezoelectrics may provide a viable alternative. This approach requires only simple electrical circuitry and very little or no electrical power. Shunted piezoelectrics have been shown to provide an efficient …

A Nonlinear Pre-Filter To Prevent Departure And/Or Pilot-Induced Oscillations (Pio) Due To Actuator Rate Limiting, Michael J. Chapa

Theses and Dissertations

Closed loop instability caused by excess phase lag induced by actuator rate limiting has been suspected in many aircraft departures from controlled flight and pilot-induced oscillations (PIO). As part of the joint Air Force Institute of Technology Test Pilot School (AFITITPS) program, a nonlinear rate limiter pre-filter (RLPF) was developed to minimize the phase lag induced by rate limiting. RLFF performance was evaluated inside the feedback path, but primary emphasis was on the pilot command path. Closed loop computer and motion-based flight simulation were conducted to prepare for the flight test. The HAVE FILTER flight test project was flown using …

Fatigue Response Of Repaired Thick Aluminum Panels With Bondline Flaws, David S. Conley

Theses and Dissertations

his research investigated the fatigue response of precracked 558 x 177.8 x 6.35 mm (22.0 x 7.0 x 0.25 in) 2024-T351 aluminum panels repaired with single-sided partially bonded, unidirectional, eighteen ply boron/epoxy reinforcements. Disbonds were introduced into the bondline of each repair during the adhesion process using teflon inserts. Five different disbond configurations, with varying disbond locations and sizes, were tested. Each repaired panel was subjected to constant amplitude cyclic fatigue loading with a maximum stress of 120MPa. Results from the different configurations were compared against one another and against repaired panels with no debonds to assess the effect of …

Simsat: A Satellite System Simulator And Experimental Test Bed For Air Force Research, James E. Colebank, R. Dan Jones, Randall D. Pollak, Donald M. Mannebach, George R. Nagy

Theses and Dissertations

SIMSAT (the SIMulation SATellite) is an AFIT-sponsored program to develop a laboratory-based physical satellite simulator. SIMSAT supports experimentation in areas of attitude control, precision pointing, and vibration suppression. SIMSAT development began with the purchase of a three-axis gas bearing which simulates a torque-free space environment. SIMSAT subsystems provide power, attitude control, telemetry, and structural support to experimental payloads. Project challenges included integration of attitude control software/hardware, high-output power storage devices, remote communications, high-frequency data collection, structural design, and computer display outputs.

A Statistical Analysis Of Space Structure Mode Localization, Amy M. Cox

Theses and Dissertations

Cyclic structures, such as antenna arrays, multi-bay trusses, and compressor blades, are significantly impacted by slight changes to system periodicity. Manufacturing errors of 5% or less can result in drastic changes to a structure's modal behavior. This change in modal behavior is significant, since it may result in the focusing of modal energy to individual substructures of the system. Poor modal identification can result in poorly designed control systems, resulting in shape control and pointing issues for space antennae. Additionally, modal energy localization may damage individual system components due to unanticipated levels of cyclic loading, leading to high cycle fatigue.

Space Launch Operations And The Lean Aerospace Initiative, Troy L. Endicott

Theses and Dissertations

This study analyzes current expendable launch procedures and identifies truly lean, value-added steps in launch operation enterprises as they relate to the Lean Aerospace Initiative (LAI). LAI and the concepts of lean thinning are discussed and followed by a review of current and future launch system requirements and their opportunities for lean practices. The study also discusses in detail current Delta II expendable launch processing operations and presents results in a case study that show how lean principles have helped the Delta II launch team drastically reduce on-pad time, restructure its testing philosophy, and streamline its operations flow. Many of …

Effects Of Pressure Gradients On Turbulent Boundary Layer Flow Over A Flat Plate With Riblets, Franklin L. Dement Jr.

Theses and Dissertations

The Air Force Institute of Technology Boundary Layer Research Facility test section was modified to create controlled non-zero streamwise pressure gradients. The capability of the modified facility to reproduce theoretical laminar boundary layer velocity profiles and to create a self-preserving flow with an adverse streamwise pressure gradient was verified with three-dimensional laser Doppler anemometry. The effects of streamwise adverse and favorable pressure gradients on turbulent boundary layer flow characteristics (velocity profiles, turbulence and skin friction) and vortex formation over a flat plate with riblets at low speed (U = 5 mIs) were studied. Normal and spanwise velocity profiles for both …

East Coast Abort Modeling With Rtls Elimination For The Space Shuttle-Liquid Fly Back Booster Launch System, Thomas L. Miller Jr.

Theses and Dissertations

This study investigates the ability of the proposed Liquid Fly Back Booster, a replacement for the Space Shuttle's Solid Rocket Boosters (SRBs), to eliminate the need for the Return to Launch Site (RTLS) abort mode. A Fortran model of a nominal launch trajectory was perturbed to simulate a single Space Shuttle Main Engine-out (SSME-out) abort scenario at different times in the launch with the goal being to abort to the southern most landing site possible. The model accounts for vehicle lift, drag, dynamic pressure, throttling times and includes atmospheric effects to enhance fidelity. Results show the RTLS abort mode can …

Design And Analysis Of On-Orbit Servicing Architectures For The Global Positioning System Constellation, Gregg A. Leisman, Adam D. Wallen

Theses and Dissertations

Satellites are the only major Air Force systems with no maintenance, routine repair, or upgrade capability. The result is expensive satellites and a heavy reliance on access to space. At the same time, satellite design is maturing and reducing the cost to produce satellites with longer design lives. This works against the ability to keep the technology on satellites current without frequent replacement of those satellites. The Global Positioning System Joint Program Office realizes that it must change its mode of operations to quickly meet new requirements while minimizing cost. The possibility of using robotic servicing architectures to solve these …

A Comparative Analysis Of The Iridium® And Globalstar® Satellite Transmission Paths, Kenneth E. Crowe

Theses and Dissertations

Globalstar and Iridium will provide valuable global communications assets for business, humanitarian aid and military operations. However, the level of coverage and the quality of the transmission path of these systems are strongly dependent on the latitude of the user and, due to their orbital characteristics, both systems provide reduced levels of coverage at low latitudes. Additionally, the L- and S-Band frequencies utilized by these systems are prone to ionospheric interference at low latitudes. The results of extensive simulation analysis indicate that the Globalstar constellation architecture provides a considerably better transmission path than Iridium's in several important areas, including path …

Heat Transfer To The Inclined Trailing Wall Of An Open Cavity, Orval A. Powell

Theses and Dissertations

Experimental and computational heat transfer investigations were performed on a cavity with an inclined trailing wall (20-degrees to the horizontal), simulating one under investigation for use in a scramjet engine. Heat transfer data are reported in the form of Stanton number obtained using a curve fit to the recorded transient surface temperature history under cold flow conditions. Ascending from the reattachment point, the Stanton number increased by nearly 50% due to flow compression. This effect of flow compression was also evident at the junction of the cavity floor and inclined trailing wall, where the Stanton number also increased by 50%. …

Electro-Hydrodynamic Pumped Hydraulic Actuation With Application To Active Vibration Control, Ahmad Reza Kashani, Sung Kang, Kevin P. Hallinan

Mechanical and Aerospace Engineering Faculty Publications

A new type of actuation device has been conceptualized that meets the needs of both large displacement, force and bandwidth within a package more compact than currently available magnetostrictive and stack-type piezoelectric actuators of similar rating. This concept relies on micro-scale electrohydrodynamic (EHD) pumping of a dielectric liquid within small channels. Configured as an actuator, the EHD pump(s) would be used to move fluid between two reservoirs—each having a compliant membrane that interfaces to the world to provide the means to achieve vibration cancellation or micro actuation.

Ordinarily limited to generating flow in macroscale applications, the EHD pump, when operating …

Anti-Ballistic Missile Laser Predictive Avoidance Of Satellites: Theory And Software For Real-Time Processing And Deconfliction Of Satellite Ephemerides With A Moving Platform Laser, David J. Vloedman

Theses and Dissertations

The Anti-Ballistic missile Laser (ABL) Project is committed to defense against attack from enemy-launched Theater Ballistic Missiles using an airborne laser platform to disable an enemy missile in the boost phase of launch. Wielding a laser of this power and scope requires that no collateral damage be caused by laser energy which may escape from the theater of engagement. The most likely track of such a laser would pose a significant threat to space-based assets. The Predictive Avoidance algorithm is designed to predict the path of a given laser firing sequence, and perform real-time forecasting of, and deconfliction with, the …

Robust Eigenstructure Assignment Using Positive Definite Output Feedback Control, Adam G. Harris

Theses and Dissertations

This research investigates a method of eigenstructure assignment for the classes of controllers known as positive definite output feedback control. The research began with a closed loop system with output feedback control that utilizes a collocated actuator-sensor pair. It is shown that this system is robust because it is globally stable for positive definite feedback. Analytical analysis is then completed to determine gains that minimize a cost function that is the error between the desired and achievable (assuming positive definite output feedback) eigenstructure. Examples are given at the end of the thesis to validate the computer code and theory results.

Space Maneuver Vehicle Orbital Mission Planner: Development Of Application And Analysis Of On-Demand Maneuvering Ability, Shon P. Williams

Theses and Dissertations

The USAF has developed the Space Maneuver Vehicle (SMV) to fulfill the requirement for flexibility, rapid response, and on-demand maneuverability of space assets. This reusable satellite merges the efficiency and readiness of aircraft-like operations with the capability of global coverage from space. Designed to provide over 10,500 fps of velocity change (or delta-v) while in orbit, the SMV out-maneuvers existing satellites by up to 100 times. This thesis helps transition the SMV to the operational area by demonstrating their responsiveness to varied mission taskings. The SMV Orbital Mission Planner allows the operator to place any number of SMVs in orbit …

Whole Spacecraft Vibration Isolation, Gregory G. Karahalis

Theses and Dissertations

The Department of Defense identified launch vibration isolation as a major research interest. Reducing the loads a satellite experiences during launch will greatly enhance the reliability, lifetime, and payload to structure ratio. DoD satellite programs stand to benefit significantly from advances in vibration isolation technology.