Aerospace Engineering Commons^™

Fully Coupled Internal Radiative Heat Transfer For The 3d Material Response Of Heat Shield, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The radiative transfer equation (RTE) is strongly coupled to the material response code KATS. A P-1 approximation model of RTE is used to account for radiation heat transfer within the material. First, the verification of the RTE model is performed by comparing the numerical and analytical solutions. Next, the coupling scheme is validated by comparing the temperature profiles of pure conduction and conduction coupled with radiative emission. The validation study is conducted on Marschall et al. cases (radiant heating, arc-jet heating, and space shuttle entry), 3D Block, 2D IsoQ sample, and Stardust Return Capsule. The validation results agree well for …

Scale Model Test To Estimate Thermal Damage By Fire In Aircraft Cargo, Jian Gao, Tsuneyoshi Matsuoka, Yuji Nakamura

Progress in Scale Modeling, an International Journal

The Federal Aviation Administration (FAA) requires fire detectors to alarm within one minute of the start of a fire in cargo compartments of airplanes. To determine whether such alarm timing works, investigations of the thermal damage to ceilings and other structures during the early stage of a fire were accomplished to demonstrate compliance with these FAA regulations. The objective was to test the feasibility of predicting convective heat transfer in early stage of a cargo compartment fire by conducting reduced scale (lab scale) experiments. First, the scaling laws was derived and validated. Then, full-scale and half-scale experiments were performed with …

Data-Driven Tools Guided By First-Principles For Scale Modeling, Sadegh Poozesh

Progress in Scale Modeling, an International Journal

For decades, traditional scale-modeling techniques have been relying on first-principles models (FPMs). FPMs have been used to find non-dimensional numbers (PIs) and identify normalized underlying forces and energies behind the phenomenon in focus. The two main challenges with FPM-based PIs extraction are finding the relevant PIs and proper correlations between PIs. The emergence and surge of data-driven modeling (DDM) provide a new opportunity to leverage experimental data in model development across scales/plants. In this paper, first, the two mentioned issues in PIs development will be elaborated to reveal the gap, and second, a new insight into scale modeling and similarity …

Numerical Reconstruction Of Spalled Particle Trajectories In An Arc-Jet Environment, Raghava S. C. Davuluri, Sean C. C. Bailey, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

To evaluate the effects of spallation on ablative material, it is necessary to evaluate the mass loss. To do so, a Lagrangian particle trajectory code is used to reconstruct trajectories that match the experimental data for all kinematic parameters. The results from spallation experiments conducted at the NASA HYMETS facility over a wedge sample were used. A data-driven adaptive methodology was used to adapts the ejection parameters until the numerical trajectory matches the experimental data. The preliminary reconstruction results show that the size of the particles seemed to be correlated with the location of the ejection event. The size of …

The Kentucky Re-Entry Universal Payload System (Krups): Orbital Flight, James Tyler Nichols

Theses and Dissertations--Mechanical and Aerospace Engineering

Due to the uniqueness of atmospheric entry environments, ground facilities cannot accurately replicate re-entry conditions. Consequently, scientists primarily rely on numerical models to predict these conditions and inform Thermal Protection System (TPS) designs. These models often lack flight validation, which is necessary for increasing their fidelity. Thus, there is a substantial need to obtain such data to advance modeling capabilities.

The Kentucky Re-entry Universal Payload System (KRUPS) is an adaptable test-bed for scientific experimentation with initial application to TPS. This vehicle was designed at the University of Kentucky to serve as an inexpensive means of obtaining validation data to enhance …

Measurements Of Wind Turbine Wake Evolution And Trajectory During Morning Boundary Layer Transition And Under Wake Steering Conditions Via Unmanned Aerial Vehicles, Stewart Nelson

Theses and Dissertations--Mechanical and Aerospace Engineering

In July of 2019, a flight campaign was conducted using semi-autonomous Unmanned Aerial Vehicles (UAVs) at the Port Alma Kruger Energy wind farm in Ontario, Canada, to study various aspects of wind turbine wake evolution. Horizontal transects across the wakes were measured using modified fixed-wing aircraft fitted with a five-hole probe to measure the wind velocity vector. Reference boundary layer conditions were measured by an octocopter with an assortment of mounted sensors flying vertical profiles upstream of the turbines. Three experiments were conducted during the campaign, which consisted of a study on wake behavior during the morning boundary layer transition, …

Turbulence Suppression In An Axially Rotating Pipe, Alyn J. Smith

Theses and Dissertations--Mechanical and Aerospace Engineering

The phenomenon of turbulence suppression in a rotating pipe flow system has been well documented by past research and experimentation. Despite this, the methods that drive this phenomenon have not yet been effectively characterized, especially at higher Reynolds numbers. While many experiments have been performed to better understand swirling turbulent pipe flow, a difficulty that arises is how to test for high levels of rotation without reducing the Reynolds number. This thesis documents the design and construction of a new pressurized pipe flow system at the University of Kentucky aimed at achieving high Reynolds numbers without causing a reduction in …

Attitude Control And Consensus On So(3) Using Sinusoids: Theory And Application To Small Satellites, Roshan Anandrao Chavan

Theses and Dissertations--Mechanical and Aerospace Engineering

We present and analyze kinematic-level and dynamic-level feedback control algorithms for single agent attitude control and multi-agent attitude consensus on SO(3). The kinematic-level algorithms yield attitude feedback controls that are piecewise-continuous sinusoidal angular velocities. The dynamic-level algorithms yield attitude feedback controls that are relative angles of rotational-mass actuators, which are continuous but only piecewise continuously differentiable sinusoids. Furthermore, the dynamic-level algorithms are designed to accommodate actuator stroke constraint. We present application of the dynamic-level control algorithms to attitude control and consensus of small-satellites.

Modeling Thin Layers In Material Response Solvers, Christen Setters

Theses and Dissertations--Mechanical and Aerospace Engineering

Thermal Protection Systems (TPS) are a necessary component for atmospheric entry. Most TPS contain thin layers of various materials such as ceramic coatings, pore sealers and bonding agents. When modeling TPS, these thin layers are often neglected due to the difference in scale between the TPS (centimeters) and the thin layers (micrometers). In this study, a volume-averaging flux-conservation method is implemented in the governing equations of a finite volume material response code. The model proposes the addition of a volume and area fraction coefficient which utilizes a weighted-averaging between the amount of thin layer and heat shield material in a …

A Computational Fluid-Structure Interaction Method For Simulating Supersonic Parachute Inflation, Jonathan Boustani

Theses and Dissertations--Mechanical and Aerospace Engineering

Following the successful landing of the Curiosity rover on the Martian surface in 2012, NASA/JPL conducted the low-density supersonic decelerator (LDSD) missions to develop large diameter parachutes to land the increasingly heavier payloads being sent to the Martian surface. Unexpectedly, both of the tested parachutes failed far below their design loads. It became clear that there was an inability to model and predict loads that occur during supersonic parachute inflation. In this dissertation, a new computational method that was developed to provide NASA with the capability to simulate supersonic parachute inflation is presented and validated. The method considers the loose …

Structural Optimization Of Space Transit Vehicle Concept, Hercules, James Philip Rogers

Theses and Dissertations--Mechanical and Aerospace Engineering

STRUCTURAL OPTIMIZATION OF SPACE TRANSIT VEHICLE CONCEPT, HERCULES:

A COMPARATIVE STUDY OF STRUCTURAL OPTIONS

Hercules is a vehicle concept developed by NASA Langley's Vehicle Analysis Branch to satisfy the need for sustainable transit between Earth, the moon, and Mars. Hercules features unprecedented abort capabilities and mission flexibility to aid in NASA's Mars campaign. By utilizing modern software to perform structural analysis and optimization for a large selection of stiffened panel concepts, beam concepts, and materials trends in the structural optimization emerge. These trends will be invaluable for the design of future spacecraft needed to fulfill similar roles.

The structural optimization …

Electromagnetic Formation Control Using Frequency Multiplexing, Zahra Abbasi

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation addresses control of relative positions and orientations of formation flying satellites using magnetic interactions. Electromagnetic formation flight (EMFF) is implemented, in which each satellite is equipped with a set of electromagnetic coils to generate an electromagnetic field. Traditional EMFF technique applies DC magnetic fields which lead to a nonlinear and highly coupled formation dynamics that allow for only position or orientation control of the satellites. We present a new frequency multiplexing method, which is a technique that uses multi-frequency sinusoidal controls, to approximately decouple the formation dynamics and to provide enough controls for both position and orientation control. …

Electric Power Systems And Components For Electric Aircraft, Damien Lawhorn

Theses and Dissertations--Electrical and Computer Engineering

Electric aircraft have gained increasing attention in recent years due to their potential for environmental and economic benefits over conventional airplanes. In order to offer competitive flight times and payload capabilities, electric aircraft power systems (EAPS) must exhibit extremely high efficiencies and power densities. While advancements in enabling technologies have progressed the development of high performance EAPS, further research is required.

One challenge in the design of EAPS is determining the best topology to be employed. This work proposes a new graph theory based method for the optimal design of EAPS. This method takes into account data surveyed from a …

Atv Dynamics And Pediatric Rider Safety, James T. Auxier Ii

Theses and Dissertations--Biomedical Engineering

It has been observed through numerous academic and governmental agency studies that pediatric all-terrain vehicle ridership carries significant risk of injury and death. While no doubt valuable to safety, the post-hoc approach employed in these studies does little to explain the why and how behind the risk factors. Furthermore, there has been no prolonged, widespread, organized, and concerted effort to reconstruct and catalog the details and causes of the large (20,000+) number of ATV-related injuries that occur each year as has been done for road-based motor vehicle accidents. This dissertation takes the opposite approach from a meta-analysis and instead examines …

Influence Of Size Effects On Surface Generation During Finish Machining And Surface Integrity In Ti-6al-4v, Ian S. Brown

Theses and Dissertations--Mechanical and Aerospace Engineering

Finish machining is an essential manufacturing process that is used to enhance the mechanical characteristics of critical components. The deformation that occurs at the tool and workpiece interface in finish machining significantly affects a host of component properties, commonly referred to as “surface integrity” properties. Surface roughness is a machining deformation-affected characteristic that is of high relevance in contemporary manufacturing. However, over recent decades it has been made clear that the material properties of the deformed surface layers are relevant to component performance as well. Predicting the overall surface quality of a machined component is of great relevance to the …

Flame Stabilization Of A Premixed Jet In Vitiated Coflow, Tyler Owens

Theses and Dissertations--Mechanical and Aerospace Engineering

Premixed staged combustion in gas turbine engines can reduce emissions by lowering peak flame temperatures but can also lead to different stability characteristics when compared to traditional combustors. High pressure ratio and subsequently high temperatures can lead to conditions suitable for both autoignition and premixed flame propagation in an environment where spatial fuel/air variations are present.

An experimental facility which issues a premixed jet into a coflowing vitiated mixture was studied to examine the stability behavior, resulting in a lifted flame. The effective ignition delay observed flame was much greater than homogeneous ignition delay calculations for the same conditions. It …

Development Of Universal Solver For High Enthalpy Flows Through Ablative Materials, Umran Duzel

Theses and Dissertations--Mechanical and Aerospace Engineering

Atmospheric entry occurs at very high speeds which produces high temperature around the vehicle. Entry vehicles are thus equipped with Thermal Protection Systems which are usually made of ablative materials. This dissertation presents a new solver that models the atmospheric entry environment and the thermal protection systems. In this approach, both the external flow and the porous heat shield are solved using the same computational domain. The new solver uses the Volume Averaged Navier-Stokes Equations adapted for hypersonic non-equilibrium flow, and is thus valid for both domains. The code is verified using analytical problems, set of benchmarks and also a …

Carbon Oxidation At The Atomic Level: A Computational Study On Oxidative Graphene Etching And Pitting Of Graphitic Carbon Surfaces, Simon Schmitt

Theses and Dissertations--Mechanical and Aerospace Engineering

In order to understand the oxidation of solid carbon materials by oxygen-containing gases, carbon oxidation has to be studied on the atomic level where the surface reactions occur. Graphene and graphite are etched by oxygen to form characteristic pits that are scattered across the material surface, and pitting in turn leads to microstructural changes that determine the macroscopic oxidation behavior. While this is a well-documented phenomenon, it is heretofore poorly understood due to the notorious difficulty of experiments and a lack of comprehensive computational studies. The main objective of the present work is the development of a computational framework from …

Applications Of Drones In Atmospheric Chemistry, Travis J. Schuyler

Theses and Dissertations--Chemistry

The emission of greenhouse gases (GHGs) has changed the composition of the atmosphere during the Anthropocene. A major technical and scientific challenge is quantifying the resulting fugitive trace gas fluxes under variable meteorological conditions. Accurately documenting the sources and magnitude of GHGs emission is an important undertaking for discriminating contributions of different processes to radiative forcing. Therefore, the adverse environmental and health effects of undetected gas leaks motivates new methods of detecting, characterizing, and quantifying plumes of fugitive trace gases. Currently, there is no mobile platform able to quantify trace gases at altitudes(UASs), or drones, can be deployed on-site in …

Using A Balloon-Launched Unmanned Glider To Validate Real-Time Wrf Modeling, Travis J. Schuyler, S. M. Iman Gohari, Gary Pundsack, Donald Berchoff, Marcelo I. Guzman

Chemistry Faculty Publications

The use of small unmanned aerial systems (sUAS) for meteorological measurements has expanded significantly in recent years. SUAS are efficient platforms for collecting data with high resolution in both space and time, providing opportunities for enhanced atmospheric sampling. Furthermore, advances in mesoscale weather research and forecasting (WRF) modeling and graphical processing unit (GPU) computing have enabled high resolution weather modeling. In this manuscript, a balloon-launched unmanned glider, complete with a suite of sensors to measure atmospheric temperature, pressure, and relative humidity, is deployed for validation of real-time weather models. This work demonstrates the usefulness of sUAS for validating and improving …

Design And Testing Of A Wind Energy Harnessing System For Forced Convective Drying Of Grain In Low Wind Speed, Warm And Humid Climates, Francis Akumabi Agbali

Theses and Dissertations--Biosystems and Agricultural Engineering

Forced convective drying using a wind turbine mechanically connected to a ventilation fan was hypothesized for low cost and rapid grain drying in developing countries. The idea was tested using an expandable wind turbine blade system with variable pitch, at low wind speeds in a wind tunnel. The design was based on empirical and theoretical models embedded in a graphical user interface (GUI) created to estimate airflow-power requirements for drying ear corn. Output airflow (0.0016 - 0.0052 m³kg^-1s^-1) increased within the study wind speed range (2.0 - 5.5 m/s). System efficiency peak (8.6%) was …

Enhanced Surface Integrity With Thermally Stable Residual Stress Fields And Nanostructures In Cryogenic Processing Of Titanium Alloy Ti-6al-4v, James R. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

Burnishing is a chipless finishing process used to improve surface integrity by severe plastic deformation (SPD) of surface asperities. As surface integrity in large measure defines the functional performance and fatigue life of aerospace alloys, burnishing is thus a means of increasing the fatigue life of critical components, such as turbine and compressor blades in gas turbine engines. Therefore, the primary objective of this dissertation is to characterize the burnishing-induced surface integrity of Ti-6Al-4V alloy in terms of the implemented processing parameters. As the impact of cooling mechanisms on surface integrity from SPD processing is largely unexplored, a particular emphasis …

Single-Degree-Of-Freedom Experiments Demonstrating Electromagnetic Formation Flying For Small Satellite Swarms Using Piecewise-Sinusoidal Controls, Ajin Sunny

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis presents a decentralized electromagnetic formation flying (EMFF) control method using frequency-multiplexed sinusoidal control signals. We demonstrate the EMFF control approach in open-loop and closed-loop control experiments using a single-degree-of-freedom testbed with an electromagnetic actuation system (EAS). The EAS sense the relative position and velocity between satellites and implement a frequency-multiplexed sinusoidal control signal. We use a laser-rangefinder device to capture the relative position and an ARM-based microcontroller to implement the closed-loop control algorithm. We custom-design and build the EAS that implements the formation control in one dimension. The experimental results in this thesis demonstrate the feasibility of the …

Design Process For The Containment And Manipulation Of Liquids In Microgravity, Chris Meek

Theses and Dissertations--Mechanical and Aerospace Engineering

In order to enhance accessibility to microgravity research, the design process for experiments on the ISS must be streamlined and accessible to all scientific disciplines, not just aerospace engineers. Thus, a general design and analysis toolbox with accompanying best practices manual for microgravity liquid containment is proposed. The work presented in this thesis improves the design process by introducing a modular liquid tank design which can be filled, drained, or act as a passive liquid-gas separation device. It can also be pressurized, and used for aerosol spray. This tank can be modified to meet the design requirements of various experimental …

Mathematical Programming Approach For The Design Of Satellite Power Systems, Allen Flath Iii

Theses and Dissertations--Electrical and Computer Engineering

Satellite power systems can be understood as islanded dc microgrids supplied by specialized and coordinated solar cell arrays augmented by electrochemical battery systems to handle high-power loads and periods of eclipse. The periodic availability of power, the limited capacity of batteries, and the dependence of all mission service on power consumption create a unique situation in which temporal power and energy scarcity exist. A multi-period model of an orbital satellite power system’s performance over a mission’s duration can be constructed. A modular power system architecture is used to characterize the system’s constraints. Using mathematical programming, an optimization problem can be …

Considerations For Atmospheric Measurements With Small Unmanned Aircraft Systems, Jamey D. Jacob, Phillip B. Chilson, Adam L. Houston, Suzanne Weaver Smith

Mechanical Engineering Faculty Publications

This paper discusses results of the CLOUD-MAP (Collaboration Leading Operational UAS Development for Meteorology and Atmospheric Physics) project dedicated to developing, fielding, and evaluating integrated small unmanned aircraft systems (sUAS) for enhanced atmospheric physics measurements. The project team includes atmospheric scientists, meteorologists, engineers, computer scientists, geographers, and chemists necessary to evaluate the needs and develop the advanced sensing and imaging, robust autonomous navigation, enhanced data communication, and data management capabilities required to use sUAS in atmospheric physics. Annual integrated evaluation of the systems in coordinated field tests are being used to validate sensor performance while integrated into various sUAS platforms. …

Fracture Initiation In A Transversely Isotropic Solid: Transient Three Dimensional Analysis, Louis Milton Brock

Mechanical Engineering Faculty Publications

A transversely isotropic solid is at rest, and contains a semi-infinite, plane crack. The axis of rotational material symmetry lies in the crack plane. Application of normal point forces to each face of the crack causes transient 3D growth. The related problem of discontinuities in displacement and traction that exist on regions that exhibit dynamic similarity is first considered. Analytic results are obtained in integral transform space. These lead to equations of the Wiener–Hopf type for the fracture problem. Analytic solutions are again obtained and, upon inversion, subjected to a dynamic energy release rate criterion that includes kinetic energy. A …

Dust Control Examination Using Computational Fluid Dynamics Modeling And Laboratory Testing Of Vortecone And Impingement Screen Filters, Ashish R. Kumar

Theses and Dissertations--Mining Engineering

Heavy industries, such as mining, generate dust in quantities that present an occupational health hazard. Prolonged exposure to the respirable dust has been found to result in many irreversible occupational ailments in thousands of miners. In underground mining applications, a variety of scrubbing systems are used to remove dust near the zones of generation. However, the wire-mesh type fibrous screens in the flooded-bed dust scrubbers used on continuous miners, are prone to clogging due to the accumulation of dust particles. This clogging results in a reduced capture efficiency and a higher exposure to the personnel. This research establishes the Vortecone, …

Thermo-Mechanical Coupling For Ablation, Rui Fu

Theses and Dissertations--Mechanical and Aerospace Engineering

In order to investigate the thermal stress and expansion as well as the associated strain effect on material properties caused by high temperature and large temperature gradient, a two-way thermo-mechanical coupling solver is developed. This solver integrates a new structural response module to the Kentucky Aerothermodynamics and Thermal response System (KATS) framework. The structural solver uses a finite volume approach to solve either hyperbolic equations for transient solid mechanics, or elliptic equations for static solid mechanics. Then, based on the same framework, a quasi-static approach is used to couple the structural response and thermal response to estimate the thermal expansion …

Wing-Tip Vortex Evolution In Turbulence, Hari Charan Ghimire

Theses and Dissertations--Mechanical and Aerospace Engineering

Planar and stereo particle image velocimetry measurements were conducted of a wing-tip vortex decaying in free-stream turbulence in order to understand the evolution of a vortex and its decay mechanism. The vortex decayed faster in the presence of turbulence. The decay of the circulation was found to be almost entirely due to a decrease in circulation of the vortex core, caused by the relative decrease in peak tangential velocity without a corresponding increase in core radius. These events were found to be connected with the stripping of core fluid from the vortex core. The increased rate of decay of the …