Aerospace Engineering Commons^™

Investigation And Comparison Of Proportional Navigation Guidance And Beam Rider Guidance, Ertac Olgun

Electrical & Computer Engineering Theses & Dissertations

Air defense has an increasing importance in today's wars. To gain the advantage in air combat, pursuit interceptor aircraft, which use Air-to-Air Missiles (AAMs), have become more and more significant. However, these are not sufficient alone. The importance of Surface-to-Air Missiles (SAMs) also can not be ignored in air defense.

SAMs can use different tactical navigation guidance methods. Of these, two of the more important guidance methods are Proportional Navigation Guidance and Beam Rider Guidance, which are investigated in this thesis. To understand the idea better, a brief description and discussion of missiles are provided. Parts of the guided missiles …

The Influence Of Pressure Relaxation On The Structure Of An Axial Vortex, Robert L. Ash, Irfan Zardadkhan, Allan J. Zuckerwar

Mechanical & Aerospace Engineering Faculty Publications

Governing equations including the effects of pressure relaxation have been utilized to study an incompressible, steady-state viscous axial vortex with specified far-field circulation. When sound generation is attributed to a velocity gradient tensor-pressure gradient product, the modified conservation of momentum equations that result yield an exact solution for a steady, incompressible axial vortex. The vortex velocity profile has been shown to closely approximate experimental vortex measurements in air and water over a wide range of circulation-based Reynolds numbers. The influence of temperature and humidity on the pressure relaxation coefficient in air has been examined using theoretical and empirical approaches, and …

Drag Reduction Of A Modern Straight Truck, Drew Landman, Matthew Cragun, Mike Mccormick, Richard Wood

Mechanical & Aerospace Engineering Faculty Publications

A wind tunnel test program was conducted at the Langley Full Scale Tunnel (LFST) to evaluate the performance of five passive drag reduction configurations on a modern straight truck at full scale. Configurations were tested in a build-up fashion with results representing a cumulative effect. Tested configurations include a front valance, a front box fairing, a boat-tail, an ideal side-skirt, and a practical side-skirt. Configurations were evaluated over a nominal 9 degree yaw sweep to establish wind averaged drag coefficients using SAE J1252. Genuine replicate yaw sweeps were used in an uncertainty analysis. Results show up to 28% improvement in …

Enhancement Technique For Aerial Images, Sertan Erkanli, Ahmet Gungor Pakfiliz, Jiang Li

Electrical & Computer Engineering Faculty Publications

Recently, we proposed an enhancement technique for uniformly and non-uniformly illuminated dark images that provides high color accuracy and better balance between the luminance and the contrast in images to improve the visual representations of digital images. In this paper we define an improved version of the proposed algorithm to enhance aerial images in order to reduce the gap between direct observation of a scene and its recorded image.

Balloon Borne Mars Research Platforms, Sean Michael Hancock

Mechanical & Aerospace Engineering Theses & Dissertations

Aerial platforms can fill a measurement gap between orbiters and rovers, providing planetary scale high resolution in situ measurements, access to scientifically interesting terrain that is either inaccessible or hazardous to rovers, and serve as a planet-wide delivery platforms to deploy surface probes and rovers to areas inaccessible given existing entry, descent, and landing systems. A permanent robotic outpost on the Martian surface can utilize locally-derived hydrogen as a lifting gas for balloon systems deployed from Mars. That approach can simplify the inflation and launch of aerial vehicles while allowing for a long duration deployment campaign that is not constrained …

Fault-Injection Experiment For The Statistical Characterization Of Faults In Avionics Communication System, Amy M. Yates

Electrical & Computer Engineering Theses & Dissertations

Since flight control systems perform safety-critical functions, it is important to understand the possible effects on the closed-loop dynamical system's performance caused by these faults. The purpose of this project is to design the software and hardware needed to add fault-injection and monitoring capabilities to ROBUS-2, a flight communication system. ROBUS-2 is the current version of the fault-tolerant computer communication system used by the Scalable Processor-Independent Design for Enhanced Reliability (SPIDER), a general-purpose fault-tolerant integrated modular architecture (IMA) developed at the NASA Langley Research Center. The major components of SPIDER include processing elements (PEs) to perform calculations, bus interface units …

Optimization And Oscillation Of A Two-Dimensional Bump To Enhance Airfoil Performance, Dinesh Atchala

Mechanical & Aerospace Engineering Theses & Dissertations

The objective of this project is to improve the aerodynamic performance of an aircraft in transonic speed using a two dimensional contour bump. A natural laminar flow airfoil, RAE5243, has been chosen for the validation case to demonstrate the adequacy of the flow solver used in this study. 2D contour bump is parameterized as the bump position via airfoil, the crest position via bump, maximum height and length of the bump for the parametric study. After these studies, one of the gradient based optimization techniques is utilized to optimize the 2D bump parameters to achieve an augmentation in lift-to-drag …

Analytic Construction Of Periodic Orbits In The Restricted Three-Body Problem, Mohammed A. Ghazy

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation explores the analytical solution properties surrounding a nominal periodic orbit in two different planes, the plane of motion of the two primaries and a plane perpendicular to the line joining the two primaries, in the circular restricted three-body problem. Assuming motion can be maintained in the plane and motion of the third body is circular, Jacobi's integral equation can be analytically integrated, yielding a closed-form expression for the period and path expressed with elliptic integral and elliptic function theory. In this case, the third body traverses a circular path with nonuniform speed. In a strict sense, the in-plane …

The Effect Of Systematic Error In Forced Oscillation Wind Tunnel Test Apparatuses On Determining Nonlinear Unsteady Aerodynamic Stability Derivatives, Brianne Y. Williams

Mechanical & Aerospace Engineering Theses & Dissertations

One of the basic problems of flight dynamics is the formulation of aerodynamic forces and moments acting on an aircraft in arbitrary motion. Classically conventional stability derivatives are used for the representation of aerodynamic loads in the aircraft equations of motion. However, for modern aircraft with highly nonlinear and unsteady aerodynamic characteristics undergoing maneuvers at high angle of attack and/or angular rates the conventional stability derivative model is no longer valid. Attempts to formulate aerodynamic model equations with unsteady terms are based on several different wind tunnel techniques: for example, captive, wind tunnel single degree-of-freedom, and wind tunnel free-flying techniques. …

Repeating Ground Track Design For Low Earth Orbit Satellite, Gurkan Gurdal

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, conditions and design requirements for a repeating ground track for a low Earth orbit satellite have been examined and several repeating ground tracks have been designed for a single area on the Earth. In order to construct and validate desired orbital results, the study has two phases which also help to investigate repeating ground track conditions: the fist one is the design phase, and second one is the simulation phase. The common objective of all the case studies is to present a closed ground track on the target by using the design parameters. In order to design …

Modified Sequential Kriging Optimization For Multidisciplinary Complex Product Simulation, Wang Hao, Wang Shaoping, Mileta M. Tomovic

Engineering Technology Faculty Publications

Directing to the high cost of computer simulation optimization problem, Kriging surrogate model is widely used to decrease the computation time. Since the sequential Kriging optimization is time consuming, this article extends the expected improvement and put forwards a modified sequential Kriging optimization (MSKO). This method changes the twice optimization problem into once by adding more than one point at the same time. Before re-fitting the Kriging model, the new sample points are verified to ensure that they do not overlap the previous one and the distance between two sample points is not too small. This article presents the double …

Section Abstracts: Aeronautical And Aerospace Sciences

Virginia Journal of Science

Abstracts of the Aeronautical and Aerospace Science Section for the 88th Annual Meeting of the Virginia Academy of Science, May 20-21, 2010, James Madison University, Harrisonburg, VA.

Optimization Of The Odu Maglev System Ridership Performance, Eric Salvador M. De Leon

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of this research is to optimize the ODU People Mover project (Maglev vehicle) by providing a valid estimate of system "ridership" performance via modeling and simulation. The results considered both service parameters and cost of system operation. The system studied three stations on a line with no closed loop which was evidently unique, but the methods and approaches used for the problem can be applied to any transportation system or layout.

To achieve this objective -- design constraints and other relevant system inputs were identified that impacted the design parameters of the transportation system and permitted assessment of …

Hybrid Intelligent Optimization Methods For Engineering Problems, Yasin Volkan Pehlivanoglu

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of optimization is to obtain the best solution under certain conditions. There are numerous optimization methods because different problems need different solution methodologies; therefore, it is difficult to construct patterns. Also mathematical modeling of a natural phenomenon is almost based on differentials. Differential equations are constructed with relative increments among the factors related to yield. Therefore, the gradients of these increments are essential to search the yield space. However, the landscape of yield is not a simple one and mostly multi-modal. Another issue is differentiability. Engineering design problems are usually nonlinear and they sometimes exhibit discontinuous derivatives for …

Estimation And Management Of Observation Time For Low Earth Orbit Satellite, Serdar Cagirdar

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, time to observation for a generic low Earth orbit satellite after being tasked for reconnaissance of a particular surface target is investigated. A closed-form Keplerian propagation of the nominal orbit is used as the process for computing a solution to the time to observation for both scanning and staring sensors. Orbital maneuvers to reach the target sooner than the nominal trajectory are also considered. In this way time to observation is managed. Lambert's problem, which is used to determine an orbit of a satellite from two position vectors and the time of flight between them, is used …

An Experimental Study Of The Near Wake Field Behind A Propeller Aircraft, Hasan Ozgur Yavas

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis presents an experimental study of the wake behind a generic, high wing, half model of a propeller driven aircraft. Wake surveys are performed at a free stream velocity of 9m/s in the Old Dominion University Low-Speed Wind Tunnel. The objective of the study is understanding the general characteristics of development and interaction of tip vortices, flap vortices, and propeller vortices in the wake of a two propeller aircraft. The measurements in the wake were obtained by using hot-wire anemometry. Measurements were made both using single wire and X-wire probes mounted on a traverse mechanism on three planes behind …

Analysis Of Helicopter Downwash/Frigate Airwake Interaction Using Statistically Designed Experiments, Yavuz Nacakli

Mechanical & Aerospace Engineering Theses & Dissertations

A research program to investigate helicopter downwash/frigate airwake interaction has been initiated using a statistically robust experimental program featuring Design of Experiments. Engineering analysis of the helicopter/frigate interface is complicated by the fact that two flowfields become inherently coupled as separation distance decreases. The final objective of this work is to develop experimental methods to determine when computer simulations need to include the effects of a coupled flowfield versus using a simplified representation by superposing the velocity fields of the individual flowfields. The work presented was performed in the Old Dominion University Low Speed Wind Tunnel using a simplified 1/50 …

Modeling And Analysis Of Low Earth Orbit Satellite And Ground Station Data Exchange Topology, Ersin Kocoglu

Mechanical & Aerospace Engineering Theses & Dissertations

In order to utilize space effectively, the primary function of satellite control in orbit around the Earth must be accomplished. This controlling process includes two main segments, ground stations serving as the controller units and orbiting satellites as the units to be controlled. This thesis explores a topological data exchange model that contains one satellite and multiple ground stations. The model is implemented in digital computer software. This model has multiple purposes and can be used to simulate satellite passes over ground stations and can also be used to predict communication time and the amount of transferred data. The model …

Multi-Element Airfoil Optimization Using Computational Fluid Dynamics, Mustafa Kubilay Ictuzer

Mechanical & Aerospace Engineering Theses & Dissertations

High-lift systems are frequently used on commercial transport aircrafts to obtain low speed performance, in terms of take-off and landing field lengths and approach speed. To maximize the take-off and landing performance within the critical restrictions required by the new generation transport wing designs, enhanced high-lift technologies are needed. Moreover, the economic realities faced by the airlines require a design that is mechanically simple and effective. These facts lead us to the optimization of the high lift systems.

Optimizing a high-lift system improves an aircraft's take-off and landing performance. The weight of the system, the advantages and the disadvantages all …

Solution Approximation For Atmospheric Flight Dynamics Using Volterra Theory, Ashraf Mohammed Kandeel Omran

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation introduces a set of novel approaches in order to facilitate and enrich Volterra theory as a nonlinear approximation technique for constructing mathematical solutions from the governing relationships describing aircraft dynamic behavior. These approaches reconnect Volterra theory and flight mechanics research, which has not been addressed in the technical literature for over twenty years. Volterra theory is known to be viable in modeling weak nonlinearities, but is not particularly well suited for directly describing high performance aircraft dynamics. In order to overcome these obstacles and restrictions of Volterra theory, the global Piecewise Volterra Approach has been developed. This new …

Active Control Of Shocks And Sonic Boom Ground Signal, Bedri Yagiz

Mechanical & Aerospace Engineering Theses & Dissertations

The manipulation of a flow field to obtain a desired change is a much heightened subject. Active flow control has been the subject of the major research areas in fluid mechanics for the past two decades. It offers new solutions for mitigation of shock strength, sonic boom alleviation, drag minimization, reducing blade-vortex interaction noise in helicopters, stall control and the performance maximization of existing designs to meet the increasing requirements of the aircraft industries. Despite the wide variety of the potential applications of active flow control, the majority of studies have been performed at subsonic speeds. The active flow control …

Constrained Optimal Orbit Design For Earth Observation, Sharon D. Vtipil

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of this dissertation is to demonstrate use requirements for a satellite observation mission can be used to determine a constrained optimal orbit based on observation site requirements, observation condition restraints, and sensor characteristics. The typical Earth observation satellite is first designed according to an appropriate orbit; then the observation requirements are used to develop a target schedule. The new design process outlines the development of the appropriate orbit by incorporating user requirements at the forefront of mission planning, not after an orbit has been selected. This research shows how to map the user requirements into constraints for the …

Analysis Of Wake Vortices Of A Medium Range Twin-Propeller Military Cargo Aircraft Using Statistically Designed Experiments, Burhan Sahin

Mechanical & Aerospace Engineering Theses & Dissertations

An experimental study was initiated to analyze the trajectories of the streamwise vortices behind the wing tip and flap of a medium range and propeller driven twin-engine military cargo aircraft. The model used for the experimental study was a generic, high wing and half model of a propeller driven aircraft and mounted within Old Dominion University's Low Speed Wind Tunnel where the wind tunnel flow speed was set to constant value of 9 m/sec. The main purpose of the study was to reach regression models for the motion and vorticity strength of both vortices under varying factors such as angle …

Dynamic Interaction Of Elevated Guideway With Uncontrolled Maglev Vehicles, Sumanth Reddy Velma

Mechanical & Aerospace Engineering Theses & Dissertations

A flexible guideway on an elevated foundation is a key to affordable maglev urban transit. The flexible guideway can undergo significant dynamic motion, either when a vehicle solely relies on an open-loop control system or when a vehicle equipped with feedback control system experiences failure, due to fluctuating magnetic forces between the vehicle and the guideway. In an attempt to understand the effect of the uncontrolled vehicle on the structural response of the guideway, its dynamic interaction with maglev vehicles is investigated under various operating conditions. To this end, two vehicle models using Electrodynamic suspension (EDS) and Electromagnetic suspension (EMS) …

Aerodynamic Analysis Of An Urban Magnetic Levitation Vehicle, John Matthew Wells

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis will detail the aerodynamic qualities of a magnetic levitation concept vehicle designed to be installed on Old Dominion University's campus. The vehicle is representative of a class of small, low-speed Maglev systems commonly referred to as Urban Maglev. A 1:12 scale model underwent testing in Old Dominion's low speed wind tunnel. Force and moment coefficients were measured over a wide range of yaw angles. Results give insight into crosswind effects and how these forces affect vehicle dynamics. An analysis of this type is important in understanding the ride quality and safety of the system. Force Coefficients range from …

Development Of A Supersonic Nozzle For A Compressed Carbon Dioxide Propulsion System Intended For Mars Surface Applications, Erin K. Blass

Mechanical & Aerospace Engineering Theses & Dissertations

This work focuses on the development of a reusable rocket nozzle unit for near-term Mars surface applications, utilizing Mars atmosphere as a propellant source. Mars atmosphere is more than 95% carbon dioxide, and its low ambient temperatures facilitate the condensation of dry ice out of the atmosphere. Furthermore, the low critical temperature of carbon dioxide enables . the production of a supercritical fluid by heating dry ice at constant volume to temperatures on the order of 400 K. The goal of this research was to develop a supersonic nozzle for reusable high-thrust propulsion. Due to the complex behavior of supercritical …

Section Abstracts: Aeronautical And Aerospace Sciences

Virginia Journal of Science

Abstracts of the Aeronautical and Aerospace Sciences Section for the 87th Annual Meeting of the Virginia Academy of Science, May 27-29, 2009, Virginia Commonwealth University, Richmond, Virginia.

A Study Of Decision Analysis Methods In Aerospace Technology Assessments, Sharon Monica Jones

Engineering Management & Systems Engineering Theses & Dissertations

Managers of aerospace technology programs and projects are faced with the challenge of making technology portfolio decisions under conditions of limited data, rapidly changing macro level factors and organizational uncertainties. To help make these technology investment decisions, some aerospace managers and analysts have used techniques from the field of decision analysis. In addition, there have been a limited number of research studies of real decision problems.

This dissertation presents the results of a non-experimental examination of the use of decision analysis methods for the assessment of aerospace technology portfolios. A web-based survey instrument was developed based on the results of …

Stability Analysis, Modeling, Simulation And Experimental Testing Of An Ems Maglev System With Structural Flexibility, Aravind M. Hanasoge

Mechanical & Aerospace Engineering Theses & Dissertations

Vehicle-guideway interaction studies of Magnetically Levitated (Maglev) vehicles indicate that structural flexibility can adversely affect the overall stability and performance of such systems. This is one of the reasons why guideways are generally made very rigid. This in turn leads to increased cost of the overall system since guideway construction forms a significant portion of the overall cost. In this dissertation, the influence of structural flexibility on the stability of Electromagnetic Suspension (EMS) Maglev systems is studied. It is shown how inherently unstable and flexible structure EMS Maglev systems can achieve guaranteed stability by using collocated actuators and sensors, along …

Mitigating Crack Propagation In A Highly Maneuverable Flight Vehicle Using Life Extending Control Logic, Mohamed Mostafa Yousef Bassyouny Elshabasy

Mechanical & Aerospace Engineering Theses & Dissertations

In this research, life extending control logic is proposed to reduce the cost of treating the aging problem of military aircraft structures and to avoid catastrophic failures and fatal accidents due to undetected cracks in the airframe components. The life extending control logic is based on load tailoring to facilitate a desired stress sequence that prolongs the structural life of the cracked airframe components by exploiting certain nonlinear crack retardation phenomena. The load is tailored to include infrequent injections of a single-cycle overload or a single-cycle overload and underload. These irregular loadings have an anti-intuitive but beneficial effect, which has …