Aerospace Engineering Commons^™

Periodic Orbit Analytic Construction In The Circular Restricted Three-Body Problem, Jay Shriram Suryawanshi

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis investigates an approximate analytic construction of halo-type periodic orbits about the collinear equilibrium points in the circular restricted three-body problem. The research follows a parallel approach to the one used by Ghazy and Newman, but the initial assumptions and utilized functions are unique to this thesis. A suppositional base solution constructed using Jacobi elliptic functions and satisfying Jacobi's integral equation is at the core of the analytic construction framework. The locus of this solution is a circle lying in the plane perpendicular to the line joining the primaries. The base solution elicits a closed-form expression for the period …

Reducing The Noise Impact Of Unmanned Aerial Vehicles By Flight Control System Augmentation, Matthew B. Galles

Mechanical & Aerospace Engineering Theses & Dissertations

The aim of this thesis is to explore methods to reduce the noise impact of unmanned aerial vehicles operating within acoustically sensitive environments by flight control system augmentation. Two methods are investigated and include: (i) reduction of sound generated by vehicle speed control while flying along a nominal path and (ii) reduction of acoustic exposure by vehicle path control while flying at a nominal speed. Both methods require incorporation of an acoustic model into the flight control system as an additional control objective and an acoustic metric to characterize primary noise sources dependent on vehicle state. An acoustic model was …

Design And Manufacture Of An Inertial Cascade Impactor For Industrial Hygiene Purposes, Hector Joel Gortaire

Mechanical & Aerospace Engineering Theses & Dissertations

Inertial cascade impactors are devices commonly used for industrial hygiene and pharmaceutical studies. Their main purpose is to separate particulate matter suspended in aerosols according to their sizes, which can vary from over 10 µm to 0.5 µm. Their versatility and ease of operation make them suitable for on-site sampling; however, designing them requires a careful consideration of the different geometric parameters that characterize them.

In this thesis, a 5-stage inertial cascade impactor was designed, modelled, constructed, and tested. The main design parameter was the volumetric flow rate, 40 l/min, which was provided by a vacuum pump. By continuous iterations, …

Characterization And Optimization Of A Propeller Test Stand, Colin Bruce Leighton Benjamin

Mechanical & Aerospace Engineering Theses & Dissertations

In recent history, there has been a rapid rise in the use of drones, and they are expanding in popularity each year. The widespread use and future capabilities of these unmanned aerial vehicles (UAVs) will call for increased study and classification of propellers to maximize their performance. As a result, it is necessary to have continuity in the development, maximization, and optimization of propeller test stand’s capability to collect accurate and precise measurements. It is of significant advantage to have the capability of accurately characterizing a propeller based on its thrust and torque. In this study, a propeller test stand …

Comparison Of Support Methods For Static Aerodynamic Testing And Validation Of A Magnetic Suspension And Balance System, Cameron K. Neill

Mechanical & Aerospace Engineering Theses & Dissertations

Magnetic suspension wind tunnels offer an alternative to traditional physical support methods. They allow for the collection of support interference free data and broader dynamic test capabilities than existing methods. Determination of dynamic aerodynamic characteristics is a crucial portion of the design of new re-entry capsules. A NASA initiative restored the 6-inch Magnetic Suspension and Balance System to support the design of a new MSBS for a supersonic wind tunnel. Before a new MSBS can be constructed, the characteristics of the current MSBS must be examined.

This thesis discusses the calibration and validation of the 6-inch MSBS. After calibration, three …

Development And Initial Evaluation Of A Reinforced Cue Detection Model To Assess Situation Awareness In Commercial Aircraft Cockpits, Aysen K. Taylor

Engineering Management & Systems Engineering Theses & Dissertations

Commercial transport aircraft of today vary greatly from early aircraft with regards to how the aircraft are controlled and the feedback provided from the machine to the human operator. Over time, as avionics systems became more automated, pilots had less direct control over their aircraft. Much research exists in the literature about automation issues, and several major accidents over the last twenty years spurred interest about how to maintain the benefits of automation while improving the overall human-machine interaction as the pilot is considered the last line of defense.

An important reason for maintaining or even improving overall pilot situation …

An Investigation Of General Criteria For Assessing Space Flight Systems Of Diverse Mission Concept Designs, Cindy L. Daniels

Engineering Management & Systems Engineering Theses & Dissertations

The purpose of this research is to investigate the general criteria for assessing the technical implementation risk factors of proposed space science missions at the mission concept stage. According to the National Aeronautics and Space Administration (NASA) Space Flight Program and Project Management Handbook (NASA, 2012), the mission concept review objectives are “To evaluate the feasibility of the proposed mission concept(s) and its fulfillment of the program's needs and objectives. To determine whether the maturity of the concept and associated planning are sufficient to begin Phase A” (p.33). Experts previously defined two technical risk factors, to assess aspects of the …

Wake Vortex Pair Formation As An Analog For Dust Devil And Tornado Genesis, Robert L. Ash

Mechanical & Aerospace Engineering Faculty Publications

In 1966, meteorologist R.S. Scorer attempted to explain how large-scale oceanic tropical depressions become hurricanes or typhoons. His model was based on the idea that when these large-scale tropical depression structures begin to rotate, mostly due to Coriolis effects, an annular outer portion of that structure changes suddenly to a potential vortex segment, with the same outer radial limit as the low-pressure structure, but with an inner radius that conserves the overall system angular momentum and kinetic energy. By analogy with the "jump" instability describing sudden buckling of a vertical column, this paper shows that his conjecture merits additional consideration. …

Parametric Study Of A Turbofan Engine With An Auxiliary High-Pressure Bypass, Sharanabasaweshwara A. Asundi, Syed Firasat Ali

Mechanical & Aerospace Engineering Faculty Publications

A parametric study of a novel turbofan engine with an auxiliary high-pressure bypass (AHPB) is presented. The underlying motivation for the study was to introduce and explore a configuration of a turbofan engine which could facilitate clean secondary burning of fuel at a higher temperature than conventionally realized. The study was also motivated by the developments in engineering materials for high-temperature applications and the potential utility of these developments. The parametric study is presented in two phases. Phase I presents a schematic of the turbofan engine with AHPB and the mathematics of the performance parameters at various stations. The proposed …

On Hybrid Temporal Basis Functions For Stable Numerical Solution Of Time Domain Boundary Integral Equations, Fang Q. Hu

Mathematics & Statistics Faculty Publications

Problems in unsteady aerodynamics and aeroacoustics can sometimes be formulated as integral equations, such as the boundary integral equations. Numerical discretization of integral equations in the time domain often leads to so-called March-On-in-Time (MOT) schemes. In the literature, the temporal basis functions used in MOT schemes have been largely limited to low-order shifted Lagrange basis functions. In order to evaluate the accuracy and effectiveness of the temporal basis functions, a Fourier analysis of the temporal interpolation schemes is carried out. Based on the Fourier analysis, the spectral resolutions of various temporal basis functions are quantified. It is argued that hybrid …

Bayesian Model Averaging Based Storage Lifetime Assessment Method For Rubber Sealing Rings, Di Liu, Shaoping Wang, Chao Zhang, Mileta M. Tomovic

Engineering Technology Faculty Publications

Rubber sealing ring is one of the most widely used seals. It is always stored for a period of time before put into use, especially in aeronautic and aerospace applications. It is necessary to evaluate the storage lifetime of rubber sealing rings. However, due to the long storage lifetime of rubber sealing rings, two issues need to be handled, including model uncertainty and lack of storage lifetime data. A Bayesian model averaging based storage lifetime assessment method for rubber sealing rings is proposed in this article. The Gamma distribution model and Weibull distribution model are selected as the candidate models …

Effects Of Automated Fiber Placement On High Strain Rate Compressive Response Of Advanced Composites, Alexander Trochez

Mechanical & Aerospace Engineering Theses & Dissertations

Automated Fiber Placement (AFP) technology shows great promise in manufacturing carbon fiber composite structures. However, intermittent defects occur in the process that can affect the overall mechanical performance of the structure. The aim of this work is to investigate the effects of deliberately placed principal defects (Gap, Overlap, and Fold) on the compressive response under quasistatic (strain rate ~10^-3 s^-1) and dynamic (strain rate ~10³ s-1) loading conditions. The controlled defects were placed at the laminate level in different orientations and depths. High strain rate compression experiments were conducted using a split Hopkinson pressure bar (SHPB) …

Aerothermodynamic Analysis Of A Mars Sample Return Earth-Entry Vehicle, Daniel A. Boyd

Mechanical & Aerospace Engineering Theses & Dissertations

Because of the severe quarantine constraints that must be imposed on any returned extraterrestrial samples, the Mars sample return Earth-entry vehicle must remain intact through sample recovery. Vehicles returning on a Mars-Earth trajectory will attain velocities exceeding any that have been experienced by prior space exploration missions, with velocities approaching 14 km/s. Velocities as high as these will encounter significant heating during atmospheric re-entry to Earth.

The purpose of this study has been to systematically investigate the aerothermodynamic challenges that will result from a Mars sample return, Earth-entry vehicle design. The goal was to enable efficient estimation of maximum stagnation …

Design And Implementation Of An Artificial Neural Network Controller For Quadrotor Flight In Confined Environment, Ahmed Mekky

Mechanical & Aerospace Engineering Theses & Dissertations

Quadrotors offer practical solutions for many applications, such as emergency rescue, surveillance, military operations, videography and many more. For this reason, they have recently attracted the attention of research and industry. Even though they have been intensively studied, quadrotors still suffer from some challenges that limit their use, such as trajectory measurement, attitude estimation, obstacle avoidance, safety precautions, and land cybersecurity. One major problem is flying in a confined environment, such as closed buildings and tunnels, where the aerodynamics around the quadrotor are affected by close proximity objects, which result in tracking performance deterioration, and sometimes instability. To address this …

Distributed Sensing And System Identification Of Cantilever Beams And Plates In The Presence Of Weak Nonlinearities, Patrick Sean Heaney

Mechanical & Aerospace Engineering Theses & Dissertations

While the mathematical foundation for modal analysis of continuous systems has long been established, flexible structures have become increasingly widespread and developing tools for understanding their mechanics has become increasingly important. Cantilever beams and plates, in particular, have been extensively studied due to their practical importance as approximations of more complex structures. The focus of this thesis is on understanding the dynamics of vibrating cantilever beams and plates through analytical and experimental investigation. Various models for the mechanics of these structures, of varying physical fidelity, are described and compared. A fiber optic sensing system is utilized to experimentally acquire distributed …

Volterra Series Approximation For Multi-Degree Of Freedom, Multi-Input, Multi-Output, Aircraft Dynamics, Alexander J. Chen

Mechanical & Aerospace Engineering Theses & Dissertations

An analytical model of a second order system is extended from a single-axis framework, to a multi-axis, multi-degree of freedom framework for a multiple input, multiple output system. This mathematical model is built from the variational approach of the Volterra series representation of nonlinear systems. The new representation describes the second order, oscillatory natural modes of a system, and shows how to organize the Volterra terms in intuitive ways. The constructed mathematical model aims to establish an organization of the Volterra kernels to allow for analytical cause and effect type analysis on system behavior.

To demonstrate the accuracy of the …

A Cost Effective Design For A Propeller Thrust/Torque Balance, Nicholas Barrett Sadowski

Mechanical & Aerospace Engineering Theses & Dissertations

Wind tunnel balances are used with aircraft models, propellers, and components to measure applied forces and moments. The design and manufacture of a balance is often for a specific test, test article and conditions. This paper discusses the theory, design, calibration, and testing of a new small propeller balance for use in a low-speed wind tunnel. The new balance is named the ODU15X15.

Theory discussed herein covers how the two measurement components, thrust and torque, affect the balance design. These loads generate strains which are in turn read by strain gages arranged in Wheatstone bridges. The design follows well known …

Learn-To-Fly Control System Design, Alexander Brent Streit

Electrical & Computer Engineering Theses & Dissertations

In order to improve aircraft flight control system development life cycle, new flight control techniques are being explored to allow the system to ``learn-to-fly" with limited a priori information of the aircraft's aerodynamic characteristics. One approach is to have a system identification process operating on-the-fly to generate mathematical models which can be used to update control laws. In this thesis, a wind tunnel experiment was conducted with a model aircraft set up to be free-to-roll, so system identification and control methods could be explored for a one-degree-of-freedom case. In particular this thesis covers the design of a novel control system …

A Constellation Of Cubesats For The Measurement Of Thermospheric Density, Kimberly Wright, James Flynn, Susannah Miller

Undergraduate Research Symposium

The ODU CubeSat is part of a multi-university collaborative project that aims to build a constellation of three small satellites that are shaped in the form of a cube with dimensions of 10 x 10 x 10 cm and will be deployed into Low Earth Orbit (LEO) to study phenomena that influence the varying thermosphere density. Variations in the density of the thermosphere fluctuate due to seasonal differences, changes in solar activity, solar radiation, and geomagnetic variations, along with temperature and altitude. These factors lead to uncertainties in current atmospheric drag models, which are a major source of error in …

Fault Mode Probability Factor Based Fault-Tolerant Control For Dissimilar Redundant Actuation System, Jun Wang, Shaoping Wang, Xingjian Wang, Mileta M. Tomovic, Cun Shi

Engineering Technology Faculty Publications

This paper presents a Fault Mode Probability Factor (FMPF) based Fault-Tolerant Control (FTC) strategy for multiple faults of Dissimilar Redundant Actuation System (DRAS) composed of Hydraulic Actuator (HA) and Electro-Hydrostatic Actuator (EHA). The long-term service and severe working conditions can result in multiple gradual faults which can ultimately degrade the system performance, resulting in the system model drift into the fault state characterized with parameter uncertainty. The paper proposes to address this problem by using the historical statistics of the multiple gradual faults and the proposed FMPF to amend the system model with parameter uncertainty. To balance the system model …

Mechanical Wear Debris Feature, Detection, And Diagnosis: A Review, Wei Hong, Wenjian Cai, Shaoping Wang, Mileta M. Tomovic

Engineering Technology Faculty Publications

Mechanical debris is an important product of friction wear, which is also a crucial approach to know the running status of a machine. Many studies have been conducted on mechanical debris in related fields such as tribology, instrument, and diagnosis. This paper presents a comprehensive review of these studies, which summarizes wear mechanisms (e.g., abrasive wear, fatigue wear, and adhesive wear) and debris features (e.g., concentration (number), size, morphology, and composition), analyzes detection methods principles (e.g., offline: spectrograph and ferrograph, and online: optical method, inductive method, resistive-capacitive method, and acoustic method), reviews developments of online inductive methods, and investigates the …

New Dimensions For A Challenging Security Environment: Growing Exposure To Critical Space Infrastructure Disruption Risk, Adrian V. Gheorghe, Alexandru Georgescu, Olga Bucovetchi, Marilena Lazăr, Cezar Scarlat

Engineering Management & Systems Engineering Faculty Publications

Space systems have become a key enabler for a wide variety of applications that are vital to the functioning of advanced societies. The trend is one of quantitative and qualitative increase of this dependence, so much so that space systems have been described as a new example of critical infrastructure. This article argues that the existence of critical space infrastructures implies the emergence of a new category of disasters related to disruption risks. We inventory those risks and make policy recommendations for what is, ultimately, a resilience governance issue.

A Monolithic Internal Strain-Gage Balance Design Based On Design For Manufacturability, Thomas Ladson Webb Iii

Mechanical & Aerospace Engineering Theses & Dissertations

This paper proposes an alternative approach to internal strain-gage balance design driven by Design for Manufacturability (DFM) principles. The objective of this research was a reduction in fabrication time and, subsequently, cost of a balance by simplifying its design while maintaining basic stiffness and sensitivity. Traditionally, the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) balance designs have relied on Electro-Discharge Machining (EDM), which is a precise but slow and, therefore, expensive process. EDM is chosen due to several factors, including material hardness, surface finish, and complex geometry, including blind cuts. The new balance design objectives require no …

Erosion Degradation Characteristics Of A Linear Electro-Hydrostatic Actuator Under A High-Frequency Turbulent Flow Field, Yuan Li, Shaoping Wang, Mileta M. Tomovic, Chao Zhang

Engineering Technology Faculty Publications

The paper proposes a performance degradation analysis model based on dynamic erosion wear for a novel Linear Electro-Hydrostatic Actuator (LEHA). Rather than the traditional statistical methods based on degradation data, the method proposed in this paper firstly analyzes the dominant progressive failure mode of the LEHA based on the working principle and working conditions of the LEHA. The Computational Fluid Dynamics (CFD) method, combining the turbulent theory and the micro erosion principle, is used to establish an erosion model of the rectification mechanism. The erosion rates for different port openings, under a time-varying flow field, are obtained. The piecewise linearization …

Human-Robot Collaborative Force-Controlled Micro-Drilling For Advanced Manufacturing And Medical Applications, Parimal Mahesh Prajapati

Mechanical & Aerospace Engineering Theses & Dissertations

Robotic drilling finds applications in diverse fields ranging from advanced manufacturing to the medical industry. Recent advances in low-cost, and human-safe, collaborative robots (e.g., Sawyer) are enabling us to rethink the possibilities in which robots can be deployed for such tedious and time-consuming tasks. This thesis presents a robotic drilling methodology with features of force-control enabled micro-drilling and human-robot collaboration to reduce programming efforts and enhance drilling performance. A Sawyer robot from Rethink Robotics, which offers safe physical interactions with a human co-worker, kinesthetic teaching, and force control, is used as the test bed. The robot’s end-effector was equipped with …

Gust Alleviation System For General Aviation Aircraft, Lucas Coleman Mills

Mechanical & Aerospace Engineering Theses & Dissertations

A designed control motion scheme to improve passenger comfort in general aviation aircraft by reducing normal acceleration and pitch rate due to turbulence is investigated. An aerodynamic math model is created for ViGYAN’s Active Ride Improvement System flight article, a one-eighth scale Pilatus Porter PC-6 with conventional forward main wing, aft horizontal and vertical tails, and a single engine with tractor configuration. The test article incorporates a full-span gust flap and forward mounted gust sensor to mechanize the gust alleviation control system, and these features are present in the dynamic model. The model is a two degree of freedom linear …

Computational Methods For Nonlinear Systems Analysis With Applications In Mathematics And Engineering, Geoffrey Kenneth Rose

Mechanical & Aerospace Engineering Theses & Dissertations

An investigation into current methods and new approaches for solving systems of nonlinear equations was performed. Nontraditional methods for implementing arc-length type solvers were developed in search of a more robust capability for solving general systems of nonlinear algebraic equations. Processes for construction of parameterized curves representing the many possible solutions to systems of equations versus finding single or point solutions were established. A procedure based on these methods was then developed to identify static equilibrium states for solutions to multi-body-dynamic systems. This methodology provided for a pictorial of the overall solution to a given system, which demonstrated the possibility …

Development Of A Data Acquisition System For Unmanned Aerial Vehicle (Uav) System Identification, Donald Joseph Lear

Mechanical & Aerospace Engineering Theses & Dissertations

Aircraft system identification techniques are developed for fixed wing Unmanned Aerial Vehicles (UAV). The use of a designed flight experiment with measured system inputs/outputs can be used to derive aircraft stability derivatives. This project set out to develop a methodology to support an experiment to model pitch damping in the longitudinal short-period mode of a UAV. A Central Composite Response Surface Design was formed using angle of attack and power levels as factors to test for the pitching moment coefficient response induced by a multistep pitching maneuver.

Selecting a high-quality data acquisition platform was critical to the success of the …

A Low Cost Inflatable Cubesat Drag Brake Utilizing Sublimation, Adam Charles Horn

Mechanical & Aerospace Engineering Theses & Dissertations

The United Nations Inter-Agency Debris Coordination Committee has adopted a 25-year post-mission lifetime requirement for any satellite orbiting below 2000 km in order to mitigate the growing orbital debris threat. Low-cost CubeSats have become important satellite platforms with startling capabilities, but this guideline restricts them to altitudes below 600 km because they remain in orbit too long. In order to enable CubeSat deployments at higher release altitudes, a low-cost, ultra-reliable deorbit device is needed.

This thesis reports on efforts to develop a deployable and passively inflatable drag brake that can deorbit from higher orbital altitudes, thereby complying with the 25-year …

Development Of The Compact Jet Engine Simulator From Concept To Useful Test Rig, Henry H. Haskin

Mechanical & Aerospace Engineering Theses & Dissertations

NASA had a goal to develop a set of modeling tools for designing next generation civil transport aircraft with reduced noise, emissions and increased fuel efficiency by 2016. To verify the models, a database of aerodynamic and acoustic data was needed for an unconventional flying wing design that was predicted to meet the goals. A Compact Jet Engine Simulator (CJES) was needed as the jet source for the 5.8% scale model. Ultra-Compact Combustor Technology from the Air Force Research Laboratory was used to reduce the conventional burner acoustic test rigs down to the required scale size. The Air Force design …