Aerospace Engineering Commons^™

Scaling Study Of Wave Rotor Turbo-Normalization Of A Small Internal Combustion Engine, Brandon D. Smith

Theses and Dissertations

One issue facing small Remotely Piloted Aircraft engines is their ability to maintain performance at altitude. Since many of these aircraft use commercial off the shelf engines originally designed for radio controlled aircraft and lawn care implements, the reduced pressure environment significantly degrades the operability of the engine as the altitude increases. An option to overcome this difficulty is to supercharge the system; however most superchargers are designed for larger, typically automotive, engines. As a supercharger's size is decreased, there are large efficiency losses. Therefore, there is a need to accomplish this function on a smaller scale without. One option …

Jet Engine Thrust Ratings, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

An Experimental Investigation Of A Goldschmied Propulsor, Joshua Roepke

Master's Theses

A wind tunnel investigation of an axisymmetric bluff body, known as a Goldschmied propulsor, was completed. This model conceptually combines boundary layer control and boundary layer ingestion into a single complementary system that is intended to use energy to reduce the axial force on the body by eliminating separation and increasing the pressure recovery aft of the body’s maximum thickness. The goal of the current project was to design, fabricate, and fully document the performance of a wind tunnel model incorporating the Goldschmied propulsor concept and complete an examination of its aerodynamic performance. The investigation took place at California Polytechnic …

Unsteady Specific Work And Isentropic Efficiency Of A Radial Turbine Driven By Pulsed Detonations, Kurt P. Rouser

Theses and Dissertations

There has been longstanding government and industry interest in pressure-gain combustion for use in Brayton cycle based engines. Theoretically, pressure-gain combustion allows heat addition with reduced entropy loss. The pulsed detonation combustor (PDC) is a device that can provide such pressure-gain combustion and possibly replace typical steady deflagration combustors. The PDC is inherently unsteady, however, and comparisons with conventional steady deflagration combustors must be based upon time-integrated performance variables. In this study, the radial turbine of a Garrett automotive turbocharger was coupled directly to and driven, full admission, by a PDC in experiments fueled by hydrogen or ethylene. Data included …

Electric Aircraft Propulsion System, Austin J. Doupe

Aerospace Engineering

This report specifies the purpose, assembly, operation, and data collection of a testing apparatus to characterize small electric aircraft propulsion systems designed for commercial use. This apparatus was constructed with the goal of determining overall system characteristics and efficiencies. The apparatus was pushed to a safety limit as deemed by advisor John Dunning and the results of the experiment were an output power of 3.2kW (25% of max rated power) and a system efficiency of 58.6%, both of which occurred at 2200 RPM. Currently the apparatus needs improvement. It should have an upgraded structure to mount to (instead of the …

High-Fidelity Low-Thrust Trajectory Determination Research And Analysis, Tyler Hill

Aerospace Engineering

This document discusses a numerical analysis method for low thrust trajectory propagation known as the proximity quotient or Q-Law. The process uses a Lyapunov feedback control law developed by Petropoulos^[1] to propagate trajectories of spacecraft by minimizing the user defined function at the target orbit. A simplified propagator is created from the core mechanics of this method in MATLAB and tested in several user defined cases to demonstrate its capabilities. Several anomalies arose in test cases where variations in eccentricity, inclination, right ascension of the ascending node, and argument of perigee were specified. Solutions to these anomalies are discussed …

De-Orbiting Upper Stage Rocket Bodies Using A Deployable High Altitude Drag Sail, Robert A. Hawkins Jr., Joseph A. Palomares

Aerospace Engineering

This report examines the effectiveness of a drag sail to de-orbit upper stage rocket bodies. Many other perturbations contribute to the de-orbiting of these rocket bodies, and these perturbations will also be discussed briefly. This paper will show the length of time needed to force the altitudes of various launch vehicle stages with varying drag area sizes to less than 100 km. The upper stage of the Delta IV launch vehicle in an orbit with an altitude of 500 km will naturally de-orbit in 720 days but when equipped with a 20 m² drag sail, it will de-orbit in …

Ramjet Fuel System, Kelsey Selin

Aerospace Engineering

No abstract provided.

Preliminary Design Of A Laboratory Cylindrical Hall-Effect Thruster, Scott Mcgrail, Sam Parker

Aerospace Engineering

A 3-cm cylindrical Hall thruster with permanent magnets was designed and modeled. The goal was to design a Hall thruster for Cal Poly’s propulsion laboratory of similar size and performance as Cal Poly’s MiXI thruster. The design process began with an investigation into the physics of Hall thrusters and selection of certain thruster parameters. The selected parameters were the diameter and depth of the channel, the total power input to the system, the discharge supply voltage, the cathode voltage, and the propellant flow rates to the anode and cathode. These parameters were used to determine the operational characteristics of the …

Implementation Of A ¼ Inch Hollow Cathode Into A Miniature Xenon Ion Thruster (Mixi), David Wayne Knapp

Master's Theses

Over the last decade, miniature ion thruster development has remained an active area of research do to its low power, low thrust, and high efficiency, however, due to several technical issues; a flight level miniature ion thruster has proved elusive. This thesis covers the design, fabrication, assembly, and test of an altered version of the Miniature Xenon Ion thruster (MiXI), originally developed by lead engineer Dr. Richard Wirz, at the California Institute of Technology (Caltech). In collaboration with Dr. Wirz, MiXI-CP-V3 was developed at Cal Poly San Luis Obispo with the goal of implementing of a ¼ inch hollow cathode …

Hapss, Hybrid Aircraft Propulsion System Synthesis, Michael W. Green

Master's Theses

Hybrid Aircraft Propulsion System Synthesis (HAPSS) is a computer program that sizes and analyzes pure-series hybrid electric propulsion systems for aircraft. The development of this program began during a NASA SBIR contract, in conjunction with Empirical Systems Aerospace (ESAero), with the creation of a propulsion fan design tool. Since the completion of this contract in July 2010, the HAPSS program has been expanded to combine the many aspects of a hybrid propulsion system such as the propulsive fans, electric motors, generators, and controllers, and the internal combustion engines.

This thesis describes the benefits and drawbacks of aircraft hybrid propulsion systems …

Primary And Secondary Flow Interactions In The Mixing Duct Of A 2-D Planer Air Augmented Rocket, Martin Roy Popish

Master's Theses

Experiments were conducted on the Cal Poly air augmented rocket (AAR) in order to characterize two-dimensional flowfield phenomenon occurring in the mixing duct. The testing utilized a direct connect system where high pressure nitrogen is fed into the combustion chamber, to form a primary flow. The high pressure nitrogen is then expanded through a nozzle, with an area ratio of 22 and an exit area of 0.75 in², up to Mach 4.3. Secondary air is entrained from a plenum chamber which is used to create a lower stagnation pressure for the secondary flow. The two flows mix in …

Cooling Requirements For The Ultra Compact Combuster, Donald D. Johnson

Theses and Dissertations

Over the past several years, AFIT and the Air Force Research Laboratory have collaboratively investigated a novel combustor system that is compact in design and has potential use in an inter-turbine burner system. The ultra-compact combustor (UCC) design wraps the combustion section circumferentially around the axial core flow and exploits the use of high-g combustion. The combustor's volume and weight are reduced by integrating the exit compressor vane and the turbine inlet vane. This creates a new hybrid vane that resides directly below the circumferential combustor. Recently, a computational effort to understand the fundamental aspects of the UCC on a …

Build Up And Operation Of An Axial Turbine Driven By A Rotary Detonation Engine, Jonathan R. Tellefsen

Theses and Dissertations

Detonation combustors provide advantages over current deflagration combustors due to their pressure gain and simplicity of design. Rotary detonation engines (RDEs) offer advantages over pulsed detonation engines (PDEs) due to a steadier exhaust and fewer total system losses. All previous research on turbine integration with detonation combustors has focused on utilizing PDEs to drive axial and centrifugal turbines. The objective of this thesis was the integration and testing of an axial turbine driven by a rotary detonation engine (RDE) to determine turbine operability. In pursuit of this objective, convergent nozzle sections were placed on the RDE to simulate the back-pressurization …

Development And Testing Of A Rotating Detonation Engine Run On Hydrogen And Air, Jason C. Shank

Theses and Dissertations

Rotating detonation engines (RDEs) have the potential for greater efficiencies over conventional engines by utilizing pressure gain combustion. A new modular RDE (6 in diameter) was developed and successfully run on hydrogen and standard air. The RDE allows for variation of injection scheme and detonation channel widths. Tests provided the operational space of the new RDE as well as characterized detonation unsteadiness. It was found that a smaller equivalence ratio than previous was required to obtain continuous detonations. Also discovered was VCJ was reached in the RDE, but not sustained.

Desensitizing Flame Structure And Exhaust Emissions To Flow Parameters In An Ultra-Compact Combuster, Adam K. Parks

Theses and Dissertations

A major thrust of turbine engine research is to improve both efficiency and thrust-to-weight ratio of the engine. A promising solution to this challenge is the Ultra-Compact Combustor (UCC). The UCC shortens the axial length of the combustor by performing combustion circumferentially on the outer diameter of the engine. The reduction in axial length yields significant weight savings and increases the thrust-to-weight ratio. The design also increases combustion efficiency by performing the combustion in a centrifugally loaded environment which allows unreacted particles to remain in the combustor sufficiently long enough to become combustion products. The Air Force Institute of Technology …

Fadec Advances Allow Better Engine Performance, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Investigating Various Propulsion Systems For An External Attachment For A Controlled-Manual De-Orbit Of The Hubble Space Telescope, Nelson De Guia

Aerospace Engineering

This reports explains the results for a proposed senior project. This project concerns the Hubble Space Telescope, and exploring the possibility of having an external propulsion attachment for a manual de-orbit. The Hubble Space Telescope was proposed to return to Earth via the Space Shuttle. Although, through the current U.S. Space Administration, the Space Shuttle has been retired before the Hubble Space Telescope was retrieved. By completing this project, the results could provide insight to what type of propulsion would best de-orbit the Hubble upon its retirement. Different propulsion systems were considered to attempt to determine an optimal attachment, varying …

Feasibility Analysis For Electrically-Powered Hoverboard, Cameron Chan, Jason Cortez, Jay Lopez

Aerospace Engineering

Composite materials are engineered by combining two or more constituent materials with significantly different physical or chemical properties in such a way that the constituents are still distinguishable, and not fully blended. Due to today’s high rising prices of gasoline and aviation fuel costs, many manufacturers have turned to the use of lightweight composites in their designs due to the advantages of the composite material, which include outstanding strength, excellent durability, high heat resistance, and significant weight reduction that the composite material properties hold. The purpose of this project is to design and construct a composite structure for an electrically-powered …

Experimental Investigation Of A 2-D Air Augmented Rocket: High Pressure Ratio And Transient Flow-Fields, Josef S. Sanchez

Master's Theses

A 2-D Air Augmented Rocket, the Cal Poly Air Augmented Rocket (CPAAR) Test Apparatus operating as a mixer-ejector was tested to investigate high stagnation pressure ratio and transient flow fields of an ejector. The primary rocket ejector was supplied with high pressure nitrogen at a maximum chamber pressure of 1758 psia and a maximum mass flow rate of 1.4 lb/s. The secondary flow air was entrained from a fixed volume plenum chamber producing pressures as low as 3.3 psia. The maximum total pressure ratio achieved was 221. The original CPAAR apparatus was rebuilt re-instrumented and capability expanded. A fixed volume …

Design And Analysis Of A Reusable N2o-Cooled Aerospike Nozzle For Labscale Hybrid Rocket Motor Testing, Daniel Joseph Grieb

Master's Theses

A reusable oxidizer-cooled annular aerospike nozzle was designed for testing on a labscale PMMA-N₂0[1] hybrid rocket motor at Cal Poly-SLO.[2] The detailed design was based on the results of previous research involving cold-flow testing of annular aerospike nozzles and hot-flow testing of oxidizer-cooled converging-diverging nozzles. In the design, nitrous oxide is routed to the aerospike through a tube that runs up the middle of the combustion chamber. The solid fuel is arranged in an annular configuration, with a solid cylinder of fuel in the center of the combustion chamber and a hollow cylinder of fuel lining …

Wind Tunnel Modeling Of Small Electric Uav Power System Performance, Nathan R. Phelps

Aerospace Engineering

This report details the design and construction of a testing apparatus for characterization of small electric aircraft power systems designed for use in the California Polytechnic State University San Luis Obispo Aerospace Engineering department’s subsonic wind tunnel. This apparatus was constructed and implemented with the goal of determining system and component efficiencies of an entire power system using RC Aircraft components as an analog for systems currently in use in the current generation of small electric UAV’s in service with the US Armed Forces. The goal of these experiments was to determine where improvements in the system architecture can be …

Experimental Investigation Of A 2-D Air Augmented Rocket: Effects Of Nozzle Lip Thickness On Rocket Mixing And Entrainment, Trevor Allen Montre

Master's Theses

Cold-flow tests were performed using a simulated Air Augmented Rocket (AAR) operating as a mixer-ejector in order to investigate the effects of varied primary nozzle lip thickness on mixing and entrainment. The simulated primary rocket ejector was supplied with nitrogen at a maximum chamber stagnation pressure of 1712 psi, and maximum flow rate of 1.67 lb_m/s. Secondary air was entrained from a plenum, producing pressures as low as 6.8 psi and yielding maximum stagnation pressure ratios as high as 160. The primary ejector nozzles each had an area ratio of approximately 20, yielding average primary exit Mach numbers …

Comet: Constrained Optimization Of Multiple-Dimensions For Efficient Trajectories, Michael Curt Conrad

Master's Theses

The paper describes the background and concepts behind a master’s thesis platform known as COMET (Constrained Optimization of Multiple-dimensions for Efficient Trajectories) created for mission designers to determine and evaluate suitable interplanetary trajectories. This includes an examination of the improvements to the global optimization algorithm, Differential Evolution, through a cascading search space pruning method and decomposition of optimization parameters. Results are compared to those produced by the European Space Agency’s Advanced Concept Team’s Multiple Gravity Assist Program. It was found that while discrepancies in the calculation of ΔV’s for flyby maneuvers exist between the two programs, COMET showed a noticeable …

A Look At Near-Term Nuclear Fission And Fusion Rockets For Human Mars Missions, Douglass W. Casey

Von Braun Symposium Student Posters

No abstract provided.

Analysis Of Plasma Jet Driven Magneto-Inertial Fusion As Potential Primary Propulsion Driver For Project Icarus, Milos Stanic

Von Braun Symposium Student Posters

No abstract provided.

Magnetic Field Mapping In The Plasmoid Thruster Experiment (Ptx), Coby W. Mccolgin

Von Braun Symposium Student Posters

No abstract provided.

A Probabilistic Design Analysis Approach In Reducing The Overall Risk Of A Fusion Propulsion Spacecraft, Natalie Walker

Von Braun Symposium Student Posters

No abstract provided.

Plasma Jet Magneto Inertial Fusion Thruster Concept, Richard Hatcher

Von Braun Symposium Student Posters

No abstract provided.

Beamed Energy For Ablative Propulsion In Near Earth Space, Grant Bergstue

Von Braun Symposium Student Posters

No abstract provided.