Aerospace Engineering Commons^™

A Study Of Mixing In A Magnetohydrodynamic (Mhd) Microfluidic Cell By Numerical Simulations, Fangping Yuan, Kakkattukuzhy M. Isaac

Collaborative Research: Actively Controllable Microfluidics with Film-Confined Redox-Magnetohydrodynamics -- Video and Data

No abstract provided.

Performance Characteristics Of Fluidic-Based Thrust Augmentation Using A Slot Jet For Unmanned Aerial Vehicle Propulsion, Brendan A. Wiedow

Mechanical & Aerospace Engineering Theses & Dissertations

Currently most small vertical takeoff and landing Unmanned Aerial Vehicles (UA V's) use a quadcopter design by utilizing four exposed blades rotating at high RPMs around a central array of components. The research performed in this thesis is focused on understanding the underlying fluid dynamics of a slot jet through the use of flow entrainment for thrust augmentation with the application to be integrated into a novel UAV system with no external moving parts. Current publicly available quadcopter rotor design type aircraft were used as a basis for the design target weight and power to estimate the amount of thrust …

Efficient General Computational Method For Estimation Of Standard Atmosphere Parameters, Nihad E. Daidzic Ph.D., Sc.D.

International Journal of Aviation, Aeronautics, and Aerospace

Knowledge of standard air temperature, pressure, density, speed of sound, and viscosity as a function of altitude is essential information in aircraft design, performance testing, pressure altimeter calibration, and several other aeronautical engineering and aviation science applications. A new efficient computational method for rapid calculations of standard atmospheric parameters up to 86 orthometric km is presented. Additionally, mass and weight of each standard atmospheric layer were calculated using a numerical integration method. The sum of all fractional masses and weights represents the total mass and weight of Earth’s atmosphere. The results obtained here agree well with measurements and models of …

A Contribution Toward Better Understanding Of Overbanking Tendency In Fixed-Wing Aircraft, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

The phenomenon of overbanking tendency for a rigid-body, fixed-wing aircraft is investigated. Overbanking tendency is defined as a spontaneous, unbalanced rolling moment that keeps increasing an airplane’s bank angle in steep turns and must be arrested by opposite aileron action. As stated by the Federal Aviation Administration, the overbanking tendency may lead to a loss of control, especially in instrument meteorological conditions. It was found in this study that the speed differential over wing halves in horizontal turns indeed creates a rolling moment that achieves maximum values for bank angles between 45 and 55 degrees. However, this induced rolling moment …

Pulsed Inductive Plasma Studies By Spectroscopy And Internal Probe Methods, Warner C. Meeks

Doctoral Dissertations

The broad effort of the Missouri Plasmoid Experiment is to elucidate the energy conversion processes in a pulsed inductive discharge due to the presence of plasma. The test article is a 440 to 490 kHz theta-pinch (or solenoidal) geometry coil with a stored energy of around 80 joules. In this work experimental hydrogen, helium, argon and xenon data at back-fill pressures of 10 to 100 mTorr (1.3 to 133.3 Pa) are obtained and interpreted. Spectral and internal probe studies were performed on MPX Mk.I and Mk.II devices, respectively. IR spectra were acquired in the Mk.I device for argon and xenon. …

Mitigation Of Moving Shocks In An Expanding Duct, Veraun Chipman

UNLV Theses, Dissertations, Professional Papers, and Capstones

Inviscid flow theory governs the bulk motion of a gas at some distance away from the walls (i.e. outside the boundary layer). That is to say, there are no viscous forces in the bulk flow, which is modeled using the Euler equations. The Euler equations are simply the Navier-Stokes equations with zero viscosity terms. An ideal inviscid fluid, when brought into contact with a surface or wall, would naturally slip right past it since the fluid has no viscosity. In real life, however, a thin boundary layer forms between the wall or surface and the bulk flow. Shock wave boundary …

Development Of An Optically-Actuated Carbon Nanotube (Cnt) Laminated Composite, John Alcorn

Von Braun Symposium Student Posters

No abstract provided.

Applications Of Femtosecond Coherent Anti-Stokes Raman Scattering In Combustion, Claresta Nicole Dennis

Open Access Dissertations

The dissertation deals with the further development of chirped-probe-pulse femtosecond coherent anti-Stokes Raman spectroscopy (CPP fs-CARS) for applications of gas phase thermometry and extension to methane concentration measurements. The main effort has been to assess the usefulness and robustness of the technique in turbulent combustors of practical interest. A primary aim has been to evaluate the use of CPP fs-CARS for vibrational N₂ thermometry in a highly turbulent environment. It has been suggested that due to the laser beam temporal overlap required for fs-CARS signal generation, the technique would be unsuccessful due to beam propagation retardation effects from density …

Particle Image Velocimetry Of Transverse Jets In Crossflow, Jesse K. Tsai, Kayla Kuzmich, David Forliti, Kriss Vanderhyde, Nils Sedano

STAR Program Research Presentations

The jet in crossflow (JICF) has been an ongoing study for the past several decades with applications in the field of fluid mechanics. This particular flow field produces vortical structures tied to the entrainment and mixing of two separate fluids. Research of the JICF seeks to determine a model and trajectory scaling law for future designs. This will help future designers to optimize the mixing and homogeneity of the two fluids to decrease emissions from pollutants, make ignition easier, and improve combustion efficiency of rockets.

Our experiment will employ Particle Image Velocimetry (PIV) to determine the fluid motion of the …

Lightweight Uav Launcher, Ben Miller, Christian Valoria, Corinne Warnock, Jake Coutlee

Mechanical Engineering

This report discusses the design, construction, and testing of a lightweight, portable UAV launcher. There is a current need for a small team of soldiers to launch a US Marine Tier II UAV in a remote location without transport. Research was conducted into existing UAV launcher designs and the pros and cons of each were recorded. This research served as a basis for concept generation during the initial design development stage. It was required that the design weigh less than 110 lbs, occupy a smaller volume than 48" x 24" 18" in its collapsed state, be portable by a single …

Feasibility Analysis Of Large Length-Scale Thermocapillary Flow Experiment For The International Space Station, Samantha Jean Alberts

Open Access Theses

The investigation of microgravity fluid dynamics emerged out of necessity with the advent of space exploration. In particular, capillary research took a leap forward in the 1960s with regards to liquid settling and interfacial dynamics. Due to inherent temperature variations in large spacecraft liquid systems, such as fuel tanks, forces develop on gas-liquid interfaces which induce thermocapillary flows. To date, thermocapillary flows have been studied in small, idealized research geometries usually under terrestrial conditions. The 1 to 3m lengths in current and future large tanks and hardware are designed based on hardware rather than research, which leaves spaceflight systems designers …

Investigation Of The Potential For Ftir As A Nondestructive Inspection Technique For Aircraft Coating Degradation, Hans G. Korth

Theses and Dissertations

Polyurethane-based aircraft coating degradation was examined using Diffuse Reflectance Infrared Fourier Transform spectroscopy (DRIFTs). Two sample sets were aged in an autoclave; each containing four samples. Sample set A contained two as-cured samples and two samples treated to a level of visual degradation. Sample set B contained one sample left as-cured and three samples of differing degradation. DRIFTs spectra were collected on sample set B and singular value decomposition (SVD) was used to reveal trends between the degradation levels. Linear discriminant analysis (LDA) was then applied to the SVD coefficients to determine the most accurate spectral band for classification of …

On The Growth Rate Of Turbulent Mixing Layers: A New Parametric Model, Jeffrey L. Freeman

Master's Theses

A new parametric model for the growth rate of turbulent mixing layers is proposed. A database of experimental and numerical mixing layer studies was extracted from the literature to support this effort. The domain of the model was limited to planar, spatial, nonreacting, free shear layers that were not affected by artificial mixing enhancement techniques. The model is split into two parts which were each tuned to optimally fit the database; equations for an incompressible growth rate were derived from the error function velocity profile, and a function for a compressibility factor was generalized from existing theory on the convective …

Evolution Of Perturbations In Flow Field Mechanics, Samantha R. Bell, David Forliti, Nils Sedano, Kriss Vanderhyde

STAR Program Research Presentations

This project explores the stability analysis of a given flow field. Specifically, where the peak disturbance occurs in a flow as this is the disturbance that is most likely to occur. In rocket combustion, it is important to understand where the maximum disturbance occurs so that the mixing of fuel can be stabilized. The instabilities are the results of frequencies in the area surrounding the flow field. The linear stability governing equations are employed to better understand the disturbance. The governing equations for continuity and momentum in the x and y directions are used to form an equation for the …

Rocket Flight Path, Jamie Waters

Undergraduate Journal of Mathematical Modeling: One + Two

This project uses Newton’s Second Law of Motion, Euler’s method, basic physics, and basic calculus to model the flight path of a rocket. From this, one can find the height and velocity at any point from launch to the maximum altitude, or apogee. This can then be compared to the actual values to see if the method of estimation is a plausible. The rocket used for this project is modeled after Bullistic-1 which was launched by the Society of Aeronautics and Rocketry at the University of South Florida.

Robust And Adaptive Nonlinear Control Of Limit Cycle Oscillations In Uavs Using Synthetic Jet Actuators, Natalie Ramos Pedroza

Doctoral Dissertations and Master's Theses

Limit cycle oscillations (LCO), also known as utter, cause significant challenges in fight control of unmanned aerial vehicles (UAVs), and could potentially lead to structural damage and catastrophic failures. LCO can be described as vibrational motions in the pitching and plunging displacements of an aircraft wing. Even in low Reynolds number (low-Re) fight regimes, LCO can exceed the limiting boundary for safe UAV fight. Further, as practical considerations motivate the design of smaller, lighter weight UAVs, there is a growing need for UAV systems that do not require heavy mechanical actuators (e.g., ailerons). To address this, the use of synthetic …

Molecular Dynamics Model Of Carbon Nanotubes In Epon 862/Detda Polymer, Guttormur Arnar Ingvason

Doctoral Dissertations and Master's Theses

The aerospace industry is interested in increasing the strength while reducing the weight of carbon fiber composite materials. Adding single walled carbon nanotubes (SWCNT) to a polymer matrix can achieve that goal by improving delamination properties of the composite. Due to the complexity of polymer molecules and the curing process, few 3-D Molecular Dynamics simulations of a polymer-SWCNT composite have been run. Our model runs on the Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS), with a COMPASS (Condensed phase Optimized Molecular Potential for Atomistic Simulations Studies) potential to represent the interactions between the atoms of the polymer and the SWCNT. This …

Applicability Of Continuum Fracture Mechanics In Atomistic Systems, Shao-Huan Cheng

Open Access Dissertations

By quantitating the amplitude of the unbounded stress, the continuum fracture mechanics defines the stress intensity factor K to characterize the stress and displacement fields in the vicinity of the crack tip, thereby developing the relation between the stress singularity and surface energy (energy release rate G). This G-K relation, assigning physical meaning to the stress intensity factor, makes these two fracture parameters widely used in predicting the onset of crack propagation. However, due to the discrete nature of the atomistic structures without stress singularity, there might be discrepancy between the failure prediction and the reality of nanostructured materials. Defining …

Ramjet Combustion Chamber, Paul Cameron Stone

Aerospace Engineering

A ramjet combustion chamber is designed and some initial assembly fabrication and test completed as a component of a ramjet graduate project for California Polytechnic State University, San Luis Obispo Supersonic Wind Tunnel. The combustor design is driven by a theoretical model created by a Cal Poly graduate student, Harrison Sykes. Temperature, pressure, and fuel flow will be measured.

Characterization Of A Spiral Microfluidic Focusing Device For Continuous Single Cell Impedance-Based Cytometry Applications, Daniel Riley

Mechanical & Aerospace Engineering Theses & Dissertations

A major focus in the field of cell characterization is the quantification of cell dielectric properties in order to develop low-cost, portable microfluidic devices that can, among other things, perform point-of-care detection of rare diseases and complete blood counts. Impedance-based cytometry has become an advantageous tool to ascertain these properties, wherein it is important that cells pass through the same point in a channel cross-section one at a time to ensure accurate and repeatable readings. This study documents the assessment of an 8-loop 160 μm (W) x 80 μm (H) spiral microchannel used to focus 10 μm polystyrene particles. In …

Guided Wave-Based J-Integral Estimation For Dynamic Stress Intensity Factors Using 3d Scanning Laser Doppler Vibrometry, J. Ayers, Christopher Todd Owen, Eric D. Swenson, Anindya Ghoshal, V. Weiss

Faculty Publications

The application of guided waves to interrogate remote areas of structural components has been researched extensively in characterizing damage. However, there exists a sparsity of work in using piezoelectric transducer-generated guided waves as a method of assessing stress intensity factors (SIF). This quantitative information enables accurate estimation of the remaining life of metallic structures exhibiting cracks, such as military and commercial transport vehicles. The proposed full wavefield approach, based on 3D laser vibrometry and piezoelectric transducer-generated guided waves, provides a practical means for estimation of dynamic stress intensity factors (DSIF) through local strain energy mapping via the J-integral. Strain energies …

Non-Equilibrium Pressure Control Of The Height Of A Large-Scale, Ground-Coupled, Rotating Fluid Column, R. L. Ash, I. R. Zardadhkan

Mechanical & Aerospace Engineering Faculty Publications

When a ground-coupled, rotating fluid column is modeled incorporating non-equilibrium pressure forces in the Navier-Stokes equations, a new exact solution results. The solution has been obtained in a similar manner to the classical equilibrium solution. Unlike the infinite-height, classical solution, the non-equilibrium pressure solution yields a ground-coupled rotating fluid column of finite height. A viscous, non-equilibrium Rankine vortex velocity distribution, developed previously, was used to demonstrate how the viscous and non-equilibrium pressure gradient forces, arising in the vicinity of the velocity gradient discontinuity that is present in the classical Rankine vortex model, effectively isolate the rotating central fluid column from …

Robust Control Methods For Nonlinear Systems With Uncertain Dynamics And Unknown Control Direction, Chau T. Ton

Doctoral Dissertations and Master's Theses

Robust nonlinear control design strategies using sliding mode control (SMC) and integral SMC (ISMC) are developed, which are capable of achieving reliable and accurate tracking control for systems containing dynamic uncertainty, unmodeled disturbances, and actuator anomalies that result in an unknown and time-varying control direction. In order to ease readability of this dissertation, detailed explanations of the relevant mathematical tools is provided, including stability denitions, Lyapunov-based stability analysis methods, SMC and ISMC fundamentals, and other basic nonlinear control tools. The contributions of the dissertation are three novel control algorithms for three different classes of nonlinear systems: single-input multiple output (SIMO) …

Payload Charging Events In The Mesosphere And Their Impact On Langmuir Type Electric Probes, T. A. Bekkeng, Aroh Barjatya, U. P. Hoppe, A. Pedersen, J. I. Moen, M. Friedrich, M. Rapp

Publications

Three sounding rockets were launched from Andøya Rocket Range in the ECOMA campaign in December 2010. The aim was to study the evolution of meteoric smoke particles during a major meteor shower. Of the various instruments onboard the rocket payload, this paper presents the data from a multi-Needle Langmuir Probe (m-NLP) and a charged dust detector. The payload floating potential, as observed using the m-NLP instrument, shows charging events on two of the three flights. These charging events cannot be explained using a simple charging model, and have implications towards the use of fixed bias Langmuir probes on sounding rockets …

Nonlinear Control For Dual Quaternion Systems, William D. Price

Doctoral Dissertations and Master's Theses

The motion of rigid bodies includes three degrees of freedom (DOF) for rotation, generally referred to as roll, pitch and yaw, and 3 DOF for translation, generally described as motion along the x, y and z axis, for a total of 6 DOF. Many complex mechanical systems exhibit this type of motion, with constraints, such as complex humanoid robotic systems, multiple ground vehicles, unmanned aerial vehicles (UAVs), multiple spacecraft vehicles, and even quantum mechanical systems. These motions historically have been analyzed independently, with separate control algorithms being developed for rotation and translation. The goal of this research is to study …

Development Of Tungsten Based Ceramic-Metallic Nuclear Fuel Containing Uranium Oxide For Nuclear Cryogenic Propulsion Stage Project, Jaewon Choi

Von Braun Symposium Student Posters

No abstract provided.

Analysis Of Stacked Linear Transformer Drivers For Application In Nuclear Fusion Propulsion, Patrick Giddens

Von Braun Symposium Student Posters

No abstract provided.

Strain Rate And Orientation Dependencies Of The Strength Of Single Crystalline Copper Under Compression, Virginie Dupont, Timothy C. Germann

Aerospace Engineering - Daytona Beach

Molecular dynamics (MD) simulations are used to model the compression under uniaxial strain of copper single crystals of different orientations at various temperatures and strain rates. Uniaxial strain is used because of the close resemblance of the resulting stress state with the one behind a shock front, while allowing a control of parameters such as strain rate and temperature to better understand the behavior under complex dynamic shock conditions. Our simulations show that for most orientations, the yield strength of the sample is increased with increasing strain rate. This yield strength is also dependent on the orientation of the sample, …

Modeling Martian Planetary Entry Descent And Landing Using Monte Carlo Driven Response Surface Methodology, Narcrisha S. Norman

Mechanical & Aerospace Engineering Theses & Dissertations

Response surface methodology (RSM) is a statistical method that explores the relationships between several descriptive variables and one or more response variables. For over sixty years, among other areas, it has been utilized in quality engineering, process engineering, aircraft engineering, economics, chemical engineering, automotive engineering and design/technique optimization. In this dissertation, RSM is utilized to produce regression models that represent the planetary entry, descent and landing (EDL) process. A complete understanding of EDL process is an essential component of any planetary exploration. Research in this area is ongoing and confidence in the ability to explore known celestial bodies is growing. …

Telescope Assembly Alignment Simulator Performance Optimization, Joshua G. Thompson, Brian Eney, Zaheer Ali, Bob Thompson

STAR Program Research Presentations

The Telescope Assembly Alignment Simulator (TAAS) calibrates scientific instruments (SI’s) that are installed on the Stratospheric Observatory For Infrared Astronomy (SOFIA). An SI’s accuracy is directly dependent on the consistent performance of the TAAS, which has never been fully characterized. After designing various thermal and optical experiments to identify the current unknowns of TAAS, we now have a far better grasp on how the equipment behaves.