Aerospace Engineering Commons^™

Modeling Of Rotor Wake Vortex Dynamics And Interactions In Non-Homogenous Vertiport Environments, Garrison P. Shaw

Doctoral Dissertations and Master's Theses

The current research serves to analyze and study the effects ground forces can have on the thrust performance of a propeller in multiple different configurations. The current research utilizes an open source Computational Fluid Dynamics (CFD) software known as OpenFOAM to generate calculate and visualize these runs. The model used for this experiment is a hybrid model that employs both a Unsteady Reynolds-Averaged Navier-Stokes (URANS) and a detached eddy simulation using a hybrid Large Eddy Simulation (LES) via a KomegaSSTDDES model. This model serves to save computational time as well as allow for accurate results. The three cases run are …

Experimental And Numerical Analysis Of Laminar And Transitional Flow Through Annular Corrugated Pipes, Joseph Russell Sargent

Theses and Dissertations

This dissertation presents studies on pressure loss through annular corrugated pipes to determine a friction factor coefficient using nitrogen. Ten different corrugated pipes’ geometries were evaluated via testing and experimentation. The ratio of corrugation height to inner diameter varied from 0.233 to 0.333 and the ratio of corrugation pitch to inner diameter varied from 0.181 to 0.446. Nitrogen flow rates between 0.25 to 94.4 standard liters per minute were used, resulting in Reynolds numbers, based on the corrugated pipe inner diameter, from 100 to 23,000. The experimental set-up was validated using smooth-pipe pressure loss measurements and the derived friction factor …

Starfish: A Compact, Biomimetic, And Adaptive Shape Memory Alloy Orbital Debris Remover, Katelyn Branaman

Doctoral Dissertations and Master's Theses

This thesis aims to turn the tides on the orbital debris issue through the fabrication and demonstration of a compact, biomimetic, and adaptive shape memory alloy actuated orbital debris remover. The design, referred to as Starfish, is discussed in detail along with its fabrication process and object capture ability. A hard skeleton crafted from PETG was combined with shape memory alloy wires and extension springs to create a biomimetic structure that operates similar to the human hand, capable of gripping a wide range of objects. Relevant simulations were performed and discussed, the iterative fabrication process used to create each component …

A Comparison Of Western And Eastern Soft Systems Approaches, John L. Anaya, John L. Anaya, John L. Anaya

Master's Theses

Soft System Approaches have been developed worldwide to help problem-solvers and decision-makers develop solutions to complex problems, such as aerospace systems. Soft System Approaches were designed to help lower the disorder of developing a complex system by increasing understanding of a situation. Four Soft System Approaches were investigated, two from the West and two from the East. Within the context of the paper, the West refers to thought patterns associated with thinkers and scientists in Europe and North America, and the East refers to those from and around China. The two from the West are Peter Checkland’s Soft Systems Methodology …

Your New Astronautics Assignment, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "Your New Astronautics Assignment" from January 31, 2024.

Design And Experimentation Of Novel Human Head Surrogate Models For Sensing Traumatic Brain Injury, Arthur T. Koster

Mechanical and Aerospace Engineering Dissertations - Archive

Brain injury is a significant source of mortality in the US and has been an important area of research over the past century. The need to understand injury thresholds and pathology coupled with the difficulty of measuring relevant injury mechanisms in a living subject logically gives rise to the idea that researchers need to create head models for use in simulation and experimentation. This study focuses on understanding the effects of material properties, size, and shape on the dynamic response of a head model so that head models used in simulations and experiments can more accurately represent the real human …

Numerical Simulation And Optimization Of Fin Configurations For Enhanced Heat Sink Performance In Aluminum And Copper Materials, Rimpy Singh

Mechanical and Aerospace Engineering Theses - Archive

The constant evolution of data centers and high-power electronic systems has raised critical challenges in heat dissipation and thermal management. Single-phase immersion cooling, where electronic components are submerged in a thermally conductive but non-electrically conductive liquid (dielectric liquid), offers improved heat dissipation capabilities and emerges as a promising alternative to traditional air-cooling methods, which often fail to meet the thermal demands of densely packed, high-power systems. This study investigates and compares the thermal performance of aluminum and copper heat sinks with fin thicknesses of 0.33 mm and 0.54 mm, respectively, using finite element analysis based on computational fluid dynamics (CFD) …

Characterization Of The Spallation Phenomenon In Ablative Thermal Protection System Materials Resulting From Arc-Jet Experiments, Kristen Price

Theses and Dissertations--Mechanical and Aerospace Engineering

Thermal protection systems are critical for protecting spacecraft from the large amounts of heating incurred during atmospheric entry. Ablative thermal protection systems in particular often consist of a carbon fiber matrix impregnated with a polymer resin and use thermal and chemical reactions to decompose the material. Weakening of these carbon fibers by oxidation, along with the impact of shear forces, results in the mechanical failure of these materials in a process known as spallation. Being able to quantify and characterize this process is important for modeling and designing heat shield materials that account for the additional spalled mass loss.

Two …

Interpersonal Skills In A Sociotechnical System: A Training Gap In Flight Decks, Kimberly Perkins, Sourojit Ghosh, Crystal Hall

Journal of Aviation/Aerospace Education & Research

This research analyzed the perceptions of interpersonal skills on established aviation safety models, Crew Resource Management (CRM), and Threat and Error Management (TEM) using feedback from industry pilots. The flight deck is a sociotechnical system where much research has focused on the technical aspect, whereas we spotlight its socio aspect. The aviation industry must invest in training pilots on interpersonal skills to enhance safety through increased efficacy of safety models integrated throughout existing training programs. A 34-question survey was disseminated across both commercial and business aviation pilots (N=822). We explored three research questions regarding pilots’ perceived training on interpersonal skills …

Cellular Level Changes Induced In Cancer Cells Due To Microgravity, Sai Deepika Reddy Yaram

Graduate Theses, Dissertations, and Problem Reports (ETD)

The increase in human activity in space has revealed several kinds of physiological challenges brought on by the absence of Earth's gravitational pull. NASA observed that during spaceflight, astronauts experience a 1-1.5% monthly loss in the mineral density of weight-bearing bones, with rehabilitation efforts on Earth often proving ineffective. This issue extends to muscles, the neuro vestibular system, the cardiovascular system, and vision. Cancer has emerged as a significant cause of mortality among astronauts, with studies up to 2017 showing that 41.3% of natural cause deaths among U.S. astronauts were due to cancer, primarily due to space radiation exposure. Cancer …

Materials Testing For Large Format 3d Printing, William Jenkins

Williams Honors College, Honors Research Projects

An ABS Carbon Fiber blend was printed into single walled hexagons at a variety of settings on a Cincinnati BAAM large format 3D printer. These hexagons were then cut down into sheets and had tensile and flexural test samples cut out of them, in order for materials testing to be performed. Tensile strength, tensile strain, young’s modulus, flexural strength, deflection and elastic modulus were all determined. A desktop CNC machine and a planer were purchased for the manufacturing of these samples, and an efficient cutting procedure was designed and optimized. After all data collection concluded, this data was thoroughly analyzed, …

Short Strand Carbon Fiber Reinforced Polylactic Acid Filament For Additive Manufacturing, Dale Chenoweth, Lukas Seggi, Luke Phillips

Williams Honors College, Honors Research Projects

In this design project, the additive manufacturing filament of short strand carbon fiber (SSCF) reinforced polylactic acid (PLA) composite was developed. The micro-size, precision cut SSCFs were mixed with the PLA pellets through a melting homogenization process. Through this process the composite material block is cut and divided into pieces for ease of pelletizing. The material block pieces are then pelletized to be fed through the single screw extruder to develop the SSCF-PLA composite filament. The SSCF-PLA filaments were manufactured with a varying amount of SSCF ranging from 0.5% to 10% of the material block's weight. Development of a 1% …

Comprehensive Review And Development Of A High-Pressure Hydraulic Impedance Tube For Vibroacoustic Attenuator Characterization, Matthew D. Beals

Dissertations, Master's Theses and Master's Reports

This research establishes a versatile test bench for characterizing hydraulic vibroacoustic attenuators. The primary evaluation metric is the transfer matrix, determined experimentally, with an emphasis on key properties such as transmission loss. To ensure accuracy and broad applicability, the methodology is based on industry-standard techniques for determining the transfer matrix. A comprehensive literature review consolidates existing approaches for hydraulic attenuator characterization. The test bench features a hydraulic impedance tube equipped with eight dynamic pressure transducer (DPT) taps strategically positioned before and after the sample interface. This setup accommodates arbitrary samples terminated with standard hydraulic fittings. Using ASTM E2611, the transfer …

Development Of Load Measurement Technique For Arbitrary Shapes, Quintin J. Cockrell

Master's Theses

Obtaining aerodynamic forces and moments about all three orthogonal axes for arbitrary shapes at arbitrary orientations in a fast manner via a measurement technique specific to Cal Poly’s low-speed wind tunnel to continually obtain the forces and moments under quasi-steady conditions is explored. A Continuous Rotation Technique (CR) uses a 6-DOF load cell and stepper motor to rotate an object about an axis for a complete rotation. The forces and moments acting upon the object pass through the stepper motor and interface plates and recorded by the load cell as the object is rotated continuously a finite number of rotations. …

Cubesats For Education, Not Any More #3, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "CubeSats for Education, Not Any More" from November 22, 2023.

Cubesats For Education, Not Any More #2, Robert J. Twiggs, Aaron Zuckerman

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs and Aaron Zuckerman titled "CubeSats for Education, Not Any More" from November 21, 2023.

Orbital Debris Mitigation: Exploring Cubesat Drag Sail Technology, Robinson Raphael

Student Works

In an era marked by remarkable advancements in space exploration and research, the advent of satellite technology has contributed accordingly to the lives of people here on Earth. Through applications that tie into broadband connectivity, weather forecasting, disaster management, etc., the occupancy in orbital domains like Low-Earth Orbit (LEO) only continues to grow. However, the presence of orbital debris emerges as a significant concern, posing threats to both operational satellites and future space missions. Resulting as a consequence due to decades of activities since the launch of Sputnik 1 in 1957, as more countries ventured into space so did the …

How Education Sats Started & A Youth Amsat-Na Program Proposal, Robert J. Twiggs, Nick Pugh

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "How Education Sats Started & A Youth Amsat-NA Program Proposal" from October 21, 2023.

Development Of User Interface And Testing Harness, Jacob Amezquita, William Albertini

College of Engineering Summer Undergraduate Research Program

No abstract provided.

Skyqube V2, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "SkyQube V2" from August 19, 2023.

Neural Network Models For Generating Synthetic Flight Data, Nathaniel Sisson

Doctoral Dissertations and Master's Theses

Flight test data is a valuable resource used in many aerospace applications. However, procuring a sufficiently large database of flight test data poses several challenges. Nominal flight tests can be expensive and time-consuming and require much post-processing depending on the availability of sensors and the quality of the sensor output. Flight test performed outside of nominal flight conditions, or flight tests in which failures are introduced, add to the inherent risk and danger associated with flight tests. The most popular alternative to flight test, numerical simulations, may fail to fully capture all non-linear behavior. While flight tests will always be …

Design And Analysis Of Asymmetric “String-Of-Pearls” Common Repeating-Ground-Track Satellite Constellations For Missions Requiring Regional Coverage, Nathaniel Choo

Theses and Dissertations

Satellite constellation design must balance many factors that emerge from multiple sources, including environmental hazards and competing mission objectives. The dynamic nature of space systems makes the problem of ‘optimal’ satellite constellation design even more challenging. Restricting satellite constellation designs to predefined geometric frameworks can alleviate many challenges associated with the design problem; however, it raises an important question: which geometric framework performs best for each mission set? This research leverages simulations, metaheuristics, and mathematical programming techniques to address this question for missions focusing on Earth-observation of one or more regions.

First, this research captures the current state of satellite …

Disc Golf Throwing Robot, Nevada S. Schultz, Sydney M. Lewis, Erick Edmundo Daza, Rachel Alysse Greenberg, Peter M. Kean

Mechanical Engineering

Disc golf companies need better methods to test disc flight. The scope of this project is to create a disc throwing robot that can throw a disc golf driver 450-500 feet, with control over the speed, spin, and release angle. Research shows that multiple disc-throwing products exist; however, none meet the full requirements of this project. The Cal Poly senior project design team created a proof-of-concept machine. This prototype started as a two-wheel mechanism. Eventually, a third wheel was added, allowing for complete control over disc spin. The three-wheel prototype reached 62 mph when perfectly calibrated. The prototype is accurate, …

Utilizing The System Engineering Trade Study Analysis Method To Analyze Patient Aeromedical Evacuation, Sara Shaghaghi, Jeremy M. Slagley, Michael E. Miller, Gaiven Varshney

Faculty Publications

The US Air Force has gone through many aeromedical patient isolation transport system designs. The first designs were developed in response to the Ebola outbreak in 2014 and, more recently, the COVID-19 pandemic. The trade study analysis part of the system engineering design method was used to analyze the historic and current aeromedical patient contamination control transport systems. A trade study is a process that evaluates alternatives based upon various “-ilities”, such as reconfigurability, flexibility, durability, cost, and more, and performs a systematic analysis to aid designers in producing a ‘good’ design alternative given the large set of possible solutions. …

Nonlinear Dynamics Analysis And Control Of Space Vehicles With Flexible Structures, Marco Fagetti

Doctoral Dissertations and Master's Theses

Space vehicles that implement hardware such as antennas, solar panels, and other extended appendages necessary for their respective missions must consider the nonlinear rotational and vibrational dynamics of these flexible structures. Formulation and analysis of these flexible structures must account for the rigid-flexible coupling present in the system dynamics for stability analysis and control design. The system model is represented by a flexible appendage attached to a central rigid body, where the flexible appendage is modeled as a cantilevered Euler-Bernoulli beam. Discretization techniques, such as the assumed modes method and the finite element method, are used to model the coupled …

Understanding The Structure Of Wing Tip Vortices Of Bio-Inspired Winglets, Greeshma C. Daniel

Doctoral Dissertations and Master's Theses

Bio-inspired wing tip devices were investigated with the goal of improving the fuel efficiency of subsonic aircraft. Particularly, the structure of a bio-inspired winglet design based on bird feathers were tested in a low-speed wind tunnel. Particle image velocimetry (PIV), was used to study the flow field at two planes aft of the wing as the wing tip vortices developed downstream. These were time-dependent, stereoscopic particle image velocimetry (sPIV) measurements carried out at two planes located at 0.7 and 2 chord distances downstream from the wing. The structure of the wingtip vortices was compared and contrasted with that formed over …

Spray Characterization Of An Unmanned Aerial Vehicle For Agricultural Spraying, Eray Önler, Hasan Berk Özyurt, Mehmet Şener, Sezen Arat, Bülent Eker, İlker Hüseyin Çelen

The Philippine Agricultural Scientist

Sustainability and higher efficiency in crop production are possible with the use of new technologies. The use of unmanned aerial vehicles (UAVs) brings many advantages, both in terms of monitoring agricultural areas and pesticide applications, and allows for early disease and damage detection as well as its application in areas without access to conventional sprayers. This study established parameters for spraying with clean water using a DJI Agras 14 MG-1P (RTK) UAV. Droplet distribution and droplet analyses were examined in the experiments carried out at different heights (1.5, 2.0, and 2.5 m) and flow rates (10, 15, 20, 25, and …

Skyqube: Developing Tools For Stem Education Focusing On Space System Engineering, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "SkyQube: Developing Tools for STEM Education Focusing on Space System Engineering" from January 11, 2023.

Precision Meteorological Prediction Employing A Data-Driven, Adaptive, Real-Time (Dart) Approach, Sujit Sinha

Theses and Dissertations--Mechanical and Aerospace Engineering

The objective of this research is to improve precision meteorological prediction, benefiting both uncrewed aerial vehicle (UAV) operations by avoiding hazardous flight conditions and tracking contaminant or toxic clouds caused by incidents, accidents, or fires. The operational concept is to collect meteorological observations from instruments mounted on a swarm of UAVs, telemeter the data to a weather simulation model, revise the predicted solution by adapting the flow field to the observations, and then transmit the updated forecast to appropriate personnel as well as to the guidance system of UAVs for repositioning to the next set of most beneficial measurements. While …

Alternatives To Reducing Aviation Fuel-Burn With Technology: Fully Electric Autonomous Taxibot, Denzil Neo

Student Works

Aircraft taxiing operations in the aerodrome were identified to consume the most jet fuel apart from the cruise phase of the flight. This was also well supported by various research associating taxi operations at large, congested airports, with high jet fuel consumption, high carbon emissions, and noise pollution. Existing literature recognised the potential to address the environmental issues of aerodrome taxi operations by operating External or Onboard Aircraft Ground Propulsion Systems (AGPS). Designed to power aircraft with sources other than their main engines, external Aircraft Ground Power Systems (AGPS) have shown the potential to significantly cut jet fuel consumption and …