Aerospace Engineering Commons^™

The Modeling Of Structural-Acoustic Interaction Using Coupled Fe/Be Method And Control Of Interior Acoustic Pressure Using Piezoelectric Actuators, Yucheng Shi

Mechanical & Aerospace Engineering Theses & Dissertations

A coupled finite element (FE) and boundary element (BE) approach is presented to model full coupled structural/acoustic/piezoelectric systems. The dual reciprocity boundary element method is used so that the natural frequencies and mode shapes of the coupled system can be obtained, and to extend this approach to time dependent problems. The boundary element method is applied to interior acoustic domains, and the results are very accurate when compared with limited exact solutions. Structural--acoustic problems are then analyzed with the coupled finite element/boundary element method, where the finite element method models the structural domain and the boundary element method models the …

Numerical Simulation Of Complex, Three-Dimensional, Turbulent-Free Jets, Robert V. Wilson

Mechanical & Aerospace Engineering Theses & Dissertations

Three-dimensional, incompressible turbulent jets with rectangular and elliptical cross-section are simulated with a finite-difference numerical method. The full Navier-Stokes equations are solved at low Reynoids numbers, whereas at high Reynolds numbers filtered forms of the equations are solved along with a sub-grid scale model to approximate the effects of the unresolved scales. A 2-N storage, third-order Runge-Kutta scheme is used for temporal discretization and a fourth-order compact scheme is used for spatial discretization. Although such methods are widely used in the simulation of compressible flows, the lack of an evolution equation for pressure or density presents particular difficulty in incompressible …

Dynamic Pulse Buckling Of Columns With Viscous Damping, Murli Kadandale

Masters Theses

This is a study of dynamic pulse buckling of columns with viscous damping. The differential equations of motion were obtained using the Bemoulli-Navier hypothesis. The effects of axial and rotary inertia were included in the analysis. The Voigt-Kelvin model for a viscoelastic material is used. The Finite Difference Method was employed to solve the differential equations of motion. First columns without geometrical imperfections were studied, and a correlation between the damping modulus and the more familiar damping ratio was obtained. Then beams with initial geometrical imperfection were studied. A suitable dynamic buckling criterion was defined. It was observed that viscous …

An Experimental Investigation Of Wall Cooling Effects On Hypersonic Boundary Layer Stability In A Quiet Wind Tunnel, Alan E. Blanchard

Mechanical & Aerospace Engineering Theses & Dissertations

One of the primary reasons for developing quiet tunnels is for the investigation of high-speed boundary-layer stability and transition phenomena without the transition-promoting effects of acoustic radiation from tunnel walls. In this experiment, a flared-cone model under adiabatic- and cooled-wall conditions was placed in a calibrated, 'quiet' Mach 6 flow and the stability of the boundary layer was investigated using a prototype constant-voltage anemometer. The results were compared with linear-stability theory predictions and good agreement was found in the prediction of second-mode frequencies and growth. In addition, the same 'N=10' criterion used to predict boundary-layer transition in subsonic, transonic, and …

Experimental Investigation Of The Inlet Deflector Configuration Variation In The Flow Field At Mach 1.9, Kyu C. Hwang

Mechanical & Aerospace Engineering Theses & Dissertations

In recent years, active research has been conducted to study the technological feasibility of supersonic laminar flow control on the wing of the High Speed Civil Transport (HSCT). For this study, the F-16XL has been chosen due to its highly swept crank wing planform that closely resembles the HSCT configurations. During flights, it is discovered that the shock wave generated from the aircraft inlet introduces disturbances on the wing where the data acquisition is conducted. The flow field about a supersonic inlet is characterized by a complex three-dimensional pattern of shock waves generated by the geometrical configuration of a deflector …

Buckling Analysis And Optimum Design Of Multidirectionally Stiffened Composite Curved Panel, Navin R. R. Jaunky

Mechanical & Aerospace Engineering Theses & Dissertations

Continuous filament grid-stiffened structure is a stiffening concept that combines structural efficiency and damage tolerance. However, buckle resistant design optimization of such structures using a finite element method is expensive and time consuming due to the number of design parameters that can be varied. An analytical optimization procedure which is simple, efficient and supports the preliminary design of grid-stiffened structures for application to combined loading cases is needed.

An analytical model for a general grid-stiffened curved panel is developed using an improved smeared theory with a first-order, shear-deformation theory to account for transverse shear flexibilities and local skin-stiffener interaction effects. …

Dynamic Unstructured Method For Prescribed And Aerodynamically Determined Relative Moving Boundary Problems, Kamakhya Prasad Singh

Mechanical & Aerospace Engineering Theses & Dissertations

A new methodology is developed to simulate unsteady flows about prescribed and aerodynamically determined moving boundary problems. The method couples the fluid dynamics and rigid-body dynamics equations to capture the time-dependent interference between stationary and moving boundaries. The unsteady, compressible, inviscid (Euler) equations are solved on dynamic, unstructured grids by an explicit, finite-volume, upwind method. For efficiency, the grid adaptation is performed within a window around the moving object. The Eulerian equations of the rigid-body dynamics are solved by a Runge-Kutta method in a non-inertial frame of reference. The two-dimensional flow solver is validated by computing the flow past a …

Numerical Investigation Of Shock-Induced Combustion Past Blunt Projectiles, Jagjit K. Ahuja

Mechanical & Aerospace Engineering Theses & Dissertations

A numerical study is conducted to simulate shock-induced combustion in premixed hydrogen-air mixtures at various free-stream conditions and parameters. Two-dimensional axisymmetric, reacting viscous flow over blunt projectiles is computed to study shock-induced combustion at Mach 5.11 and Mach 6.46 in hydrogen-air mixture. A seven-species, seven reactions finite rate hydrogen-air chemical reaction mechanism is used combined with a finite-difference, shock-fitting method to solve the complete set of Navier-Stokes and species conservation equations. In this approach, the bow shock represents a boundary of the computational domain and is treated as a discontinuity across which Rankine-Hugoniot conditions are applied. All interior details of …

Effects Of Blowing Ratios On Heat Transfer To The Throat Region Of A Porous-Walled Nozzle, Fu-Jung Chen

Theses and Dissertations

The effects of transpiration cooling on heat transfer in the throat region of a porous-walled nozzle were investigated. The experiments were performed in the AFIT low speed shock tube fitted with a Mach 2 nozzle. A blowing region was limited to the area from 1.3 cm prior to the throat to 1.2 cm downstream of the throat. The blowing ratios from -0.0002 (suction) to 0.0117 (blowing) of the main stream flow were studied. Heat flux data were taken from both sides of the nozzle. One side was transpiration cooled by secondary air injection through a porous wall, while the other …

Advanced Rover Chassis, Eric Alan Poulson, Collin Lewis, Todd Graves

Undergraduate Honors Capstone Projects

Background:

The six wheeled rover vehicle detailed in this design is intended as an upgrade test bed for the sensor array and autonomous navigation algorithms in use by Utah State University's Center for Self-Organizing and Intelligent Systems (CSOIS). The CSOIS's sensor suite can successfully detect and avoid unnavigable obstacles up to five vehicle lengths in front of the vehicle. The center presently uses a modified RC type chassis and only supports two wheel drive. This chassis was adequate to bring the CSOIS's algorithms to a proof-of-principles state, but in order to place the system in any practical application, a full …

Aerodynamic Design Optimization With Consistently Discrete Sensitivity Derivatives Via The Incremental Iterative Method, Vamshi M. Korivi

Mechanical & Aerospace Engineering Theses & Dissertations

In this study which involves advanced fluid-flow codes, an incremental iterative formulation (also known as the "delta" or "correction" form), together with the well-known spatially split approximate-factorization algorithm, is presented for solving the large, sparse systems of linear equations that are associated with aerodynamic sensitivity analysis. For the smaller two dimensional problems, a direct method can be applied to solve these linear equations in either the standard or the incremental form, in which case the two are equivalent. However, iterative methods are needed for larger two-dimensional and three dimensional applications because direct methods require more computer memory than is currently …

Finite Element Nonlinear Random Response Of Composite Panels Of Arbitrary Shape To Acoustic And Thermal Loads Applied Simultaneously, Roger R. Chen

Mechanical & Aerospace Engineering Theses & Dissertations

The nonlinear random response of composite plates to the simultaneously applied, combined acoustic/thermal loads are investigated in this dissertation. A finite element formulation for the nonlinear random response is developed. The three-node Mindlin plate element with improved transverse shear is extended and employed. The extension includes the development of the thermal geometric matrix, the mass matrix, the first- order and second-order nonlinear stiffness matrices, and the thermal and mechanical load vectors. An innovative solution procedure has been created which is believed to be the first attempt to analyze nonlinear random response of complex composite panels subjected to simultaneous acoustic and …

Towards A More Hands-On, Design-Oriented Course On Mechanisms, Burford Furman

Faculty Research, Scholarly, and Creative Activity

No abstract provided.

On The Use Of Students For Developing Engineering Laboratories, Bopaya Bidanda, Richard E. Billo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper describes a unique and innovative approach that solved the dual problem of starting up a new engineering instructional laboratory in a timely manner, and for teaching engineering students advanced skills in Automatic Data Collection. Students enrolled in a special pilot course were used to develop and startup an Automatic Data Collection laboratory. These students were assigned individual Automatic Data Collection technologies of interest and given total responsibility for the successful startup of the laboratory. The organization and structure of the course modeled the typical team oriented project development efforts in industry. Feedback from students showed the course to …

Thermal Contact Conductance Of Ceramic Substrate Junctions, K. C. Chung, H. K. Benson, John W. Sheffield

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Improved Finite Element Modeling Of The Turbofan Engine Inlet Radiation Problem, I. Danda Roy, Walter Eversman

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Improvements have been made in the finite element model of the acoustic radiated field from a turbofan engine inlet in the presence of a mean flow. The problem of acoustic radiation from a turbofan engine inlet is difficult to model numerically because of the large domain and high frequencies involved. A numerical model with conventional finite elements in the near field and wave envelope elements in the far field has been constructed. By employing an irrotational mean flow assumption, both the mean flow and the acoustic perturbation problem have been posed in an axisymmetric formulation in terms of the velocity …

Intercomparison Between Commercial Condensation Nucleus Counters And An Alternating Temperature Gradient Cloud Chamber, Darryl J. Alofs, C. K. Lutrus, Donald E. Hagen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Three Commercial CNC Counters (TSI Models 3010, 3022A, and 3025A) Are Compared with an Alternating Temperature Gradient Cloud Chamber (ALGR). Electrically Size Classified Aerosols of Sodium Chloride and Silver Are Used. Diffusional Losses within the ALGR Are Much Larger Than for the TSI Instruments: Therefore the ALGR Concentrations Are Corrected for Internal Diffusional Losses, But the TSI Instruments Are Not. the Particle Size Range Tested is 4–90 Nm. for Sodium Chloride, the TSI Concentrations Agreed Fairly Well with the Corrected ALGR at Larger Sizes, and Were Below the Corrected ALGR at Smaller Sizes. the Electrical Aerosol Classifier (EAC) Setting at …

Hamiltonian Based Adaptive Critics For Aircraft Control, S. N. Balakrishnan, Jie Shen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Aircraft designs are becoming more complex in order to either operate more efficiently as in the commercial sector or to push the performance envelopes as in the military sector. An interesting outcome of this scenario is that `control'' has come to play an important role in helping realize these objectives. Increasingly, control is becoming an integral part of an aircraft design rather than an afterthought. More effective and efficient control of an aircraft is certain to lead to improved performance at a lower cost

On A Method For Obtaining Approximate Solutions To Sturm-Liouville Problems, Serge Abrate

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A method presented recently to find approximate solutions to a Sturm-Liouville problem is shown to be a special case of a classical weighted residual method. The choice of approximation functions and convergence of the method are also examined. © 1995 American Mathematical Society.

Vibration Of Point-Supported Rectangular Composite Plates, Serge Abrate

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A general approach is presented to study the free vibrations of rectangular symmetrically laminated composite plates with point supports by using the Rayleigh-Ritz method and the Lagrange multiplier technique for enforcing the zero displacement constraints at the support locations. Polynomial approximation functions are used, and the constitutive relationships are written in terms of four lamination parameters. With these lamination parameters, the number of design variables is reduced to a minimum, which is useful for design optimization purposes, while all symmetric lay-ups are considered. This paper illustrates how the lamination parameters can be used for optimal design of vibrating plates. Results …

A New Neural Architecture For Homing Missile Guidance, S. N. Balakrishnan, Victor Biega

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We present a new neural architecture which imbeds dynamic programming solutions to solve optimal target-intercept problems. They provide feedback guidance solutions, which are optimal with any initial conditions and time-to-go, for a 2D scenario. The method discussed in this study determines an optimal control law for a system by successively adapting two networks - an action and a critic network. This method determines the control law for an entire range of initial conditions; it simultaneously determines and adapts the neural networks to the optimal control policy for both linear and nonlinear systems. In addition, it is important to know that …

System Modeling And Control Of Smart Structures, Frank J. Kern, Leslie Robert Koval, K. Chandrashekhara, Vittal S. Rao

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents multidisciplinary research and curriculum efforts at the University of Missouri-Rolla in the smart structures area. The primary objective of our project is to integrate research results with curriculum development for the benefit of students in electrical, and mechanical and aerospace engineering and engineering mechanics. The approach to the accomplishment of curriculum objectives is the development of a two-course sequence in the smart structures area with an integrated laboratory. The research portion of the project addresses structural identification and robust control methods for smart structures. A brief summary of the research results and a description of curriculum development …

Fuzzy Logic In Restructurable Flight Control Systems, S. N. Balakrishnan, H. S. Ho

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In this paper, a fuzzy logic controller (FLC) is proposed for restructurable flight control systems. The role of the FLC is to stabilize the aircraft upon a fault occurrence. The FLC derives pitch/roll/yaw controls from a generic knowledge base characterized by 49 if-then rules. A linearized model representative of a modern jet fighter provides the basis for the numerical simulation. Simulated faults include various degrees of surface loss at the right stabilator, combined with reduced ailerons and rudder control power. The FLC accomplishes the stabilization task under test conditions without any knowledge of the system parameters. The numerical results demonstrate …

Effects Of Blowing Ratio On Heat Transfer To The Throat Region Of A Porous-Walled Nozzle, Joseph L. Lenertz

Theses and Dissertations

This experiment analyzed the effects of blowing ratio on heat transfer to the throat region of a porous-walled nozzle, using the AFIT low speed shock tube. Heat flux data were taken from both sides of a two-dimensional Mach 2.0 Re-m=5.2x10⁷ nozzle using thin film resistance thermometers. One side was transpiration-cooled by secondary air injection through a sintered wall, while the other side served as a control. Control results were validated using empirical relations, and cooled side results showed up to a 14% reduction in heat transfer coefficient at blowing ratios of only 0.51%. The linear nature of cooling effectiveness …

An Investigation And Improvement Of Electrorheological (Er) Fluid Technology, Adil F. Dalal

Masters Theses

The purpose of this research was to investigate and overcome the limitations of Electrorheological (ER) fluids and to introduce this advanced technology at WMU. Electrorheological (ER) Fluids are a special class of fluids, which exhibit a reversible, infinitely variable phase transition from a liquid to a solid/semi-plastic state, in the presence of an electric field.

ER fluids can provide a unique solution to the problems of vibration isolation of systems. The applications are currently limited due to the high voltage requirements, electric power related heating and limited research into wear/abrasive characteristics of ER fluids.

A specially designed and constructed "electro-viscosimeter" …

Simulation Of Active Control Of Asymmetric Flows Around Slender Pointed Forebodies, Hazem Sharaf El-Din

Mechanical & Aerospace Engineering Theses & Dissertations

At high angles of attack, the flowfield over slender forebodies becomes asymmetric with substantial side force, which may exceed the available control capability. The unsteady compressible Navier-Stokes equations are used to investigate the effectiveness of different active control methods to alleviate and possibly eliminate the flow asymmetry and the subsequent side force. Although the research work focuses on active control methods, a passive control method has been investigated. The implicit, Roe flux-difference splitting, finite volume scheme is used for the numerical computations. Both locally-conical and three-dimensional solutions of the Navier-Stokes equations are obtained.

The asymmetric flow over five-degree semi-apex angle …

Investigation Of Wall Injectors For Supersonic Mixing Enhancement, Yaacov Haimovitch

Mechanical & Aerospace Engineering Theses & Dissertations

A comparative study of the interaction between wall mounted swept-ramp injectors and injector nozzle shape has been conducted in a constant area duct to explore techniques to enhance mixing in scramjet combustors. The scramjet combustors are currently being developed for propulsion systems applications on the envisioned hypersonic vehicles. Short combustor residence time, a requirement for fuel injection parallel to the main flow in the combustor, and an overall strong sensitivity of the vehicle performance to the propulsion system motivated the investigation. The swept-ramp injector investigated in this study produces vortex shedding and local separation downstream of the injector's nozzle exit, …

Flow Simulations About Steady-Complex And Unsteady Moving Configurations Using Structured-Overlapped And Unstructured Grids, James Charles Newman Iii

Mechanical & Aerospace Engineering Theses & Dissertations

The limiting factor in simulating flows past realistic configurations of interest has been the discretization of the physical domain on which the governing equations of fluid flow may be solved. In an attempt to circumvent this problem, many Computational Fluid Dynamic (CFD) methodologies that are based on different grid generation and domain decomposition techniques have been developed. However, due to the costs involved and expertise required, very few comparative studies between these methods have been performed. In the present work, the two CFD methodologies which show the most promise for treating complex three-dimensional configurations as well as unsteady moving boundary …

Implementation Of A Multiblock Sensitivity Analysis Method In Numerical Aerodynamic Shape Optimization, James Matthew Lacasse

Mechanical & Aerospace Engineering Theses & Dissertations

A multiblock sensitivity analysis method is applied in a numerical aerodynamic shape optimization technique. The Sensitivity Analysis Domain Decomposition (SADD) scheme which is implemented in this study was developed to reduce the computer memory requirements resulting from the aerodynamic sensitivity analysis equations, Discrete sensitivity analysis offers the ability to compute quasi-analytical derivatives in a more efficient manner than traditional finite-difference methods, which tend to be computationally expensive and prone to inaccuracies.

The direct optimization procedure couples CFD analysis based on the two-dimensional thin-layer Navier-Stokes equations with a gradient-based numerical optimization technique. The linking mechanism is the sensitivity equation derived from …

Unsteady Flow Simulations About Moving Boundary Configurations Using Dynamic Domain Decomposition Techniques, Guan-Wei Yen

Mechanical & Aerospace Engineering Theses & Dissertations

A computational method is developed to solve the coupled governing equations of an unsteady flowfield and those of rigid-body dynamics in six degrees-of-freedom (6-DOF). This method is capable of simulating the unsteady flowfields around multiple component configurations with at least one of the components in relative motion with respect to the others. Two of the important phenomena that such analyses can help us to understand are the unsteady aerodynamic interference and the boundary-induced component of such a flowfield. By hybridizing two dynamic domain decomposition techniques, the grid generation task is simplified, the computer memory requirement is reduced, and the governing …