Open Access. Powered by Scholars. Published by Universities.®

Aerospace Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 301 - 330 of 331

Full-Text Articles in Aerospace Engineering

Analysis Of Multi-Layered Materials Under High Velocity Impact Using Cth, Jason K. Lee Mar 2008

Analysis Of Multi-Layered Materials Under High Velocity Impact Using Cth, Jason K. Lee

Theses and Dissertations

Multi-layer armor containing ceramic and metallic layers has become more common in the past two decades. Typically, ceramics have high compressive strength which combined with their low density make them highly desirable for armor applications. This research effort numerically simulates high velocity impact of cylindrical projectiles on multi-layer metallic and ceramic targets of finite thickness. The impact of the projectile occurs normal to the surface of the target. The projectiles used are made of either S7 tool steel or tungsten. The targets consist of either rolled homogeneous armor, 4340 steel and boron carbide ceramic or rolled homogeneous armor and boron …

Go to article

Effects Of Environment On Creep Behavior Of Nextel 720/Alumina-Mullite Ceramic Composite At 1200°C, Christopher L. Genelin Mar 2008

Effects Of Environment On Creep Behavior Of Nextel 720/Alumina-Mullite Ceramic Composite At 1200°C, Christopher L. Genelin

Theses and Dissertations

The creep behavior of an oxide-oxide ceramic matrix composite (CMC) was investigated at 1200°C in laboratory air, in steam and in argon. The composite consisted of a porous alumina-mullite matrix reinforced with laminated, woven mullite/alumina (Nextel/720) fibers. The composite had no fiber coating and relied on its porous alumina/mullite matrix for flaw tolerance. Tensile stress-strain behavior was investigated and the tensile properties were measured at 1200°C in laboratory air. Tensile creep behavior of the CMC was examined for creep stress levels of 73, 91, 114 and 136 MPa. Creep run-out, set to 100 h, was achieved for stress levels ≤ …

Go to article

Effect Of Prior Aging On Fatigue Behavior Of Im7/Bmi 5250-4 Composite At 191°C, Christine G. Ladrido Jun 2007

Effect Of Prior Aging On Fatigue Behavior Of Im7/Bmi 5250-4 Composite At 191°C, Christine G. Ladrido

Theses and Dissertations

IM7/BMI 5250-4 with carbon fiber orientations [± 45] and [0/90] were aged in air at 191 °C for up to 1000 hours. The weight loss was analyzed during the aging process. Tension to failure tests were performed on both the unaged and aged specimens to establish a baseline for the Ultimate Tensile Strengths and Young's Modulus. Tension-tension cyclic load fatigue testing was conducted on the specimen to determine the effect of prior aging on the fatigue response of the composite. Cyclic strain accumulation was not influenced by prior aging, but it was influenced by the stress levels applied. [± 45] …

Go to article

High Temperature Degradation Of 5250-4 Polymer Resin, Patrick E. Link Jun 2007

High Temperature Degradation Of 5250-4 Polymer Resin, Patrick E. Link

Theses and Dissertations

5250-4 bismaleimide resin is used in high performance polymer matrix composites with high temperature aeronautical applications. This thesis investigated the thermal and oxidative degradation of 5250-4 neat resin powder in argon, air, and oxygen environments. The powder was aged at 163 deg. C, 177 deg. C, and 190 deg. C in all environments for at least 250 hours. Isothermal thermo-gravimetric analysis demonstrated that weight loss was negligible for aging in the argon environment, indicating weight loss is the result of an oxidative process at these temperatures. The 5250-4 powder exhibited an initial period of weight gain before eventually losing weight …

Go to article

An Exploration Of Several Structural Measurement Techniques For Usage With Functionally Graded Materials, Robert A. Reuter Dec 2006

An Exploration Of Several Structural Measurement Techniques For Usage With Functionally Graded Materials, Robert A. Reuter

Theses and Dissertations

Titanium / titanium boride functionally graded 6"x 1"x1" beams were subjected to a four-point beam test in order to critique the value of several measurement techniques. Also, finite element analysis results were compared with experimental values and general observations about the experiment were recorded. Uniform 85% TiB /15% Ti and uniform commercially pure titanium specimens were also subjected to the same loading conditions as a control. Techniques used include digital image correlation, fiber optic strain gauging, strain gauging, and differential infrared thermography techniques. The strain data results were compared with one another and to linear finite element models. It was …

Go to article

Capillary-Driven Flows Along Rounded Interior Corners, Yongkang Chen, Mark M. Weislogel, Cory L. Nardin Nov 2006

Capillary-Driven Flows Along Rounded Interior Corners, Yongkang Chen, Mark M. Weislogel, Cory L. Nardin

Mechanical and Materials Engineering Faculty Publications and Presentations

The problem of low-gravity isothermal capillary flow along interior corners that are rounded is revisited analytically in this work. By careful selection of geometric length scales and through the introduction of a new geometric scaling parameter Tc, the Navier–Stokes equation is reduced to a convenient∼O(1) form for both analytic and numeric solutions for all values of corner half-angle α and corner roundedness ratio λ for perfectly wetting fluids. The scaling and analysis of the problem captures much of the intricate geometric dependence of the viscous resistance and significantly reduces the reliance on numerical data compared with several previous solution methods …

Go to article

Modeling Fracture In Z-Pinned Composite Co-Cured Laminates Using Smeared Properties And Cohesive Elements In Dyna3d, Jason K. Freels Sep 2006

Modeling Fracture In Z-Pinned Composite Co-Cured Laminates Using Smeared Properties And Cohesive Elements In Dyna3d, Jason K. Freels

Theses and Dissertations

The purpose of the present research was three-fold: 1) gain a more sophisticated understanding of the response of co-cured composite joints with and without through-thickness reinforcement (TTR), 2) compare the behavior of specimens reinforced with various sizes and densities of reinforcement, and 3) use experimental data to verify the existing DYNA3D smeared property model. Double cantilever beam, end-notch flexure and T-section specimens reinforced with 0.011" diameter z-pins at 2% and 4% volume densities were tested to determine the mode I, mode II and mixed mode (I and II) behavior. Results were added to preliminary research in which tests were conducted …

Go to article

Freeform Extrusion Of High Solids Loading Ceramic Slurries, Part Ii: Extrusion Process Control, Michael S. Mason, Tieshu Huang, Robert G. Landers, Ming-Chuan Leu, Greg Hilmas Aug 2006

Freeform Extrusion Of High Solids Loading Ceramic Slurries, Part Ii: Extrusion Process Control, Michael S. Mason, Tieshu Huang, Robert G. Landers, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Part I of this paper provided a detailed description of a novel fabrication machine for high solids loading ceramic slurry extrusion processes and presented an empirical model of the ceramic extrusion process, viewing ram velocity as the input and extrusion force as the output. A constant extrusion force is desirable as it correlates with a constant material deposition rate and, thus, good part quality. The experimental results used to construct the model demonstrated that a constant ram velocity will not necessarily produce a constant extrusion force. In some instances the extrusion force increased until ram motor skipping occurred, and process …

Go to article

2nd Annual Undergraduate Research Conference Abstract Book, University Of Missouri--Rolla Apr 2006

2nd Annual Undergraduate Research Conference Abstract Book, University Of Missouri--Rolla

Undergraduate Research Conference at Missouri S&T

No abstract provided.

Go to article

Characterization Of Functionally Graded Materials, Benjamin D. Chapman Mar 2006

Characterization Of Functionally Graded Materials, Benjamin D. Chapman

Theses and Dissertations

The purpose of this study was to characterize the behavior of a functionally graded material through experimentation and analytical modeling. Functionally graded materials are a ceramic metal composite which transitions from metal on one face to ceramic on the opposite face. Creating reliable models required verifying the material properties. This was accomplished through the use of a static modulus of elasticity test as well as a dynamic ping test. The natural frequencies from the dynamic test were compared with finite element models to determine which material properties most accurately represented the functionally graded material. It was found that the material …

Go to article

Fretting Fatigue Behavior Of Shot-Peened In 100, Jonathan L. Ng Mar 2006

Fretting Fatigue Behavior Of Shot-Peened In 100, Jonathan L. Ng

Theses and Dissertations

The fretting fatigue behavior of shot-peened of IN 100 was investigated in this study. S-N curves were obtained for two different shot-peened intensities (7A and 12A) and were compared to those of unpeened specimens. Stress relaxation behavior under fretting fatigue was also investigated after their measurements were obtained using the X-ray diffraction method. The crack initiation location and the crack angle orientation along the surface were determined using optical and scanning electron microscopy (SEM). Cracks initiated near the trailing edge and on the contact surface for both 7A and 12A shot-peened specimens. Finite element analysis was performed using commercially available …

Go to article

Creep-Rupture Behavior Of A Woven Ceramic Matrix Composite At Elevated Temperatures In A Humid Environment, Jennifer L. Ryba Mar 2006

Creep-Rupture Behavior Of A Woven Ceramic Matrix Composite At Elevated Temperatures In A Humid Environment, Jennifer L. Ryba

Theses and Dissertations

This study focused on moisture and temperature effects on the embrittlement and stress-rupture life of the SiC/SiC CMC Syl-iBN/BN/SiC. The Syl-iBN/BN/SiC is composed of Sylramic fibers with an in-situ layer of boron nitride (Syl-iBN), boron nitride interphase (BN), and SiC matrix. Stress rupture tests and monotonic tests were performed on the specimens. Tests were conducted under 100% humidity and laboratory air environments at three temperatures, 450°C, 750°C, and 950°C. These temperatures were chosen because they fall below the intermediate range, within the range, and above the range, respectively. This study found that while this CMC does experience embrittlement at intermediate …

Go to article

Experimental And Computational Analysis Of Modes In A Partially Constrained Plate, Robert M. Vandawaker Mar 2004

Experimental And Computational Analysis Of Modes In A Partially Constrained Plate, Robert M. Vandawaker

Theses and Dissertations

The field of structural health monitoring (SHM) attempts to reduce labor and cost by allowing technicians to monitor selected properties of an aircraft's structure to detect impending failure. This research examines methods to detect damage to a thermal protection system (TPS) tile using representative 2024-T3 aluminum plates. Plates are subjected to modal analysis in single and joined conditions in an attempt to provide the capability of sensing damage to a tile on the surface of a vehicle while the sensors remain on the superstructure of the airframe. Jointly, the development of a means to model the system using finite element …

Go to article

Characterization And Modeling Of Local Electromechanical Response In Stress-Biased Piezoelectric Actuators, N. Navapan-Traiphol, Robert W. Schwartz, Daniel S. Stutts, J. Wood Jan 2004

Characterization And Modeling Of Local Electromechanical Response In Stress-Biased Piezoelectric Actuators, N. Navapan-Traiphol, Robert W. Schwartz, Daniel S. Stutts, J. Wood

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Numerous investigators have explored the factors that contribute to the high electromechanical performance of stress-biased actuators with particular attention being given to the importance of the extrinsic (domain wall translation) response mechanism. Based on the variation in lateral stress through the thickness of the piezoelectric layer within these devices, it has been suggested that the piezoelectric coefficient varies as a function of position within the layer, though no direct evidence has been previously presented. In this study, the results of Moire interferometry investigations of local strains within these devices are reviewed. The technique permits effective depth-profiling of local deformations at …

Go to article

Effect Of Polymer-Surface Mobility On Adhesion In Poly(Methyl Methacrylate)-Tape System, Bhavesh C. Gandhi, Frank D. Blum, Lokeswarappa R. Dharani Jan 2002

Effect Of Polymer-Surface Mobility On Adhesion In Poly(Methyl Methacrylate)-Tape System, Bhavesh C. Gandhi, Frank D. Blum, Lokeswarappa R. Dharani

Chemistry Faculty Research & Creative Works

The interaction between two polymer layers, especially adhesion between them, plays an important role in polymer processing and other applications. Detailed knowledge of the molecular structure and dynamics of polymer interfaces, and how they relate to macroscopic mechanical properties, should help designers construct more functional systems. Unfortunately, there have been few studies where both molecular and macroscopic studies have been performed on similar systems. In previous studies from our group, we have probed the dynamics of poly(methyl acrylate) (PMA) and thermal behavior of poly(methyl methacrylate) (PMMA) on silica. These studies helped us paint a picture for strongly bound molecules on …

Go to article

Effects Of Foreign Object Damage From Small Hard Particles On The High-Cycle Fatigue Life Of Ti-6a1-4v, Joseph L. Hamrick Ii Dec 1999

Effects Of Foreign Object Damage From Small Hard Particles On The High-Cycle Fatigue Life Of Ti-6a1-4v, Joseph L. Hamrick Ii

Theses and Dissertations

Thin rectangular samples of Ti-6Al-4V were damaged by four methods to represent foreign object damage found in turbine engine blades: 1) impact with 2 mm and 5 mm diameter glass spheres at 305 m/s, 2) impact with 2 mm and 4 mm diameter steel spheres at 305 m/s, 3) quasi-static displacement controlled indentation using steel chisels with 1 mm, 2 mm and 5 mm diameter tips and 4) shearing notches with a 2 mm diameter chisel point under a quasi-static loading condition. Finite element analysis was used to study the relationship between the stress state created by the plastic damage …

Go to article

Effect Of Interfacial Mobility On Flexural Strength And Fracture Toughness Of Glass/Epoxy Laminates, T. W. H. Wang, Frank D. Blum, Lokeswarappa R. Dharani Oct 1999

Effect Of Interfacial Mobility On Flexural Strength And Fracture Toughness Of Glass/Epoxy Laminates, T. W. H. Wang, Frank D. Blum, Lokeswarappa R. Dharani

Chemistry Faculty Research & Creative Works

Mechanical testing and surface fractography were used to characterize the fracture of E-glass fiber reinforced epoxy composites as a function of the silane coupling agent used. gamma-Aminopropyltriethoxysilane (APS) and delta-aminobutyltriethoxysilane (ABS) were used because these have been shown to have different interfacial mobilities at multilayer coverage. The values of the properties studied generally increased from untreated c, as determined from a Mode I translaminar fracture toughness tests, for the untreated composites (10.5 ± 0.4 kJ/m2) was lower than that for the ABS-treated composites (14.3 ± 2.1 kJ/m2) which was lower than that for the APS-treated composites (17.1 ± 2.4 kJ/m2). …

Go to article

Residual Strength And Fatigue Characterization Of Scs-6/Ti-6-4, Sang-Myung Lee Dec 1996

Residual Strength And Fatigue Characterization Of Scs-6/Ti-6-4, Sang-Myung Lee

Theses and Dissertations

Metal matrix composite have potential in a variety of aerospace applications, but they should be better understood before they can be employed. Despite the many studies that have contributed to characterizing the fatigue response of titanium alloy MMCs, few have researched the residual strength. The purpose of this study was to investigate the residual strength and the frequency effects on the residual strength of an unidirectional laminate of SCS-6/Ti-6-4, a titanium alloy matrix based composite under tension-tension, load-controlled conditions at elevated temperatures and different frequencies. Specimens were fatigued at frequencies of 1 and 0.01Hz, and at maximum stress of 900MPa …

Go to article

Low-Velocity Impact On Composite Sandwich Plates, Eric J. Herup Jul 1996

Low-Velocity Impact On Composite Sandwich Plates, Eric J. Herup

Theses and Dissertations

The objective of the research is to analytically model the response of composite sandwich plates to low velocity impact. A displacement based, plane stress, finite element code is modified for this purpose. Major new algorithms include 5th order Hermitian interpolation, three dimensional equilibrium integration for transverse stress calculations, sandwich core modeling as an elastic plastic foundation, loading by simulated contact with a spherical indentor, adaptive mesh, damage prediction, damage progression via stiffness reduction, and local-global analysis for displacement. An experimental effort is also included in which composite sandwich plates with graphite epoxy facesheets and Nomex honeycomb core are subjected to …

Go to article

Structural Damage Identification From Limited Measurement Data, Richard G. Cobb Mar 1996

Structural Damage Identification From Limited Measurement Data, Richard G. Cobb

Theses and Dissertations

The research focused on the development of a new method to identify damaged structural elements from a large flexible space structure on-orbit, using limited measured modal data. Limited measured modal data is loosely defined as measured data containing only a few modal frequencies and less than 10% of the total structural degrees-of-freedom. This effort was decomposed into four specific tasks. The first is the identification of partial modal properties from measured data of the nominal space structure. Second, the finite element model must be adjusted to match the measured nominal partial data. The third task is an analysis of the …

Go to article

Investigation Into The Behavior Of Geometrically Nonlinear Composite Arches, John C. Bailey Dec 1994

Investigation Into The Behavior Of Geometrically Nonlinear Composite Arches, John C. Bailey

Theses and Dissertations

This research modifies the existing finite element formulation of a potential energy based large deformation and moderate rotation theory. Hermitian shape functions replace the existing linear bending angle interpolations. Negligible differences between the two formulations indicate the underlying kinematics limit the accuracy, not the finite element interpolations. Using the new program, numerous nonlinear arch geometries are modeled to investigate the effects of arc length and thickness variations. Local and global snapping phenomena are captured as well as through the thickness shear driven nonlinearities.

Go to article

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite Subjected To Tension-Tension Cycling With Hold Time, Scott A. Grant Dec 1994

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite Subjected To Tension-Tension Cycling With Hold Time, Scott A. Grant

Theses and Dissertations

This study was carried out to investigate the elevated temperature behavior of the SiC-MAS5 cross- ply [0-90]4S ceramic matrix composite manufactured by Corning Inc. to fatigue with loading waveforms that combine the characteristics of stress rupture and high cycle fatigue. The test results were compiled in the form of S-N (cycles to failure), S-T (exposure time versus cycles to failure), S-S (energy exposure versus cycles to failure), normalized modulus degradation, strain progression, and hysteresis loop progression. From the mechanical behavior demonstrated by these curves, relationships between the effect of the environment and loading waveform were developed. In addition, a …

Go to article

Characterization Of Fatigue Behavior Of 2-D Woven Fabric Reinforced Ceramic Matrix Composite At Elevated Temperature, Daniel J. Groner Dec 1994

Characterization Of Fatigue Behavior Of 2-D Woven Fabric Reinforced Ceramic Matrix Composite At Elevated Temperature, Daniel J. Groner

Theses and Dissertations

This study investigated the fatigue behavior and associated damage mechanisms in notched and unnotched enhanced Sic-SiC ceramic matrix composite specimens at 1100°C. Stiffness degradation, strain variation, and hysteresis were evaluated to characterize material behavior. Microscopic examination was performed to characterize damage mechanisms. During high cycle-low stress fatigue tests, far less fiber-matrix interface debond was evident than in low cycle-high stress fatigue tests. Notched specimens exhibited minimal stress concentration during monotonic tensile testing and minimal notch sensitivity during fatigue testing. Damage mechanisms were also similar to unnotched.

Go to article

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite At Elevated Temperature Under Tension-Tension Loading, Craig D. Steiner Dec 1994

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite At Elevated Temperature Under Tension-Tension Loading, Craig D. Steiner

Theses and Dissertations

This study investigated the fatigue behavior and damage mechanisms of a [0-90]4s SiC-MAS ceramic matrix composite under tension-tension loading at two elevated temperatures and two frequencies. Stress and strain hystereses, maximum and minimum strain, and modulus of elasticity were evaluated to characterize the material behavior. Microscopy and fractography were used to evaluate damage progression and mechanisms. Fatigue life was independent of frequency at both temperatures.

Go to article

Fiber Enhanced Viscoelastic Damping Polymers And Their Application To Passive Vibration Control, Houchun Xia Jul 1993

Fiber Enhanced Viscoelastic Damping Polymers And Their Application To Passive Vibration Control, Houchun Xia

Mechanical & Aerospace Engineering Theses & Dissertations

A new composite damping material is investigated, which consists of a viscoelastic matrix and high elastic modulus fiber inclusions. This fiber enhanced viscoelastic damping polymer is intended to be applied to light-weight flexible structures as surface treatment for passive vibration control. A desirable packing geometry for the composite material is proposed, which is expected to produce maximum shear strain in the viscoelastic damping matrix. Subsequently, a micromechanical model is established in which the effect of fiber segment length and relative motion between neighboring fibers are taken into account. Based on this model, closed form expressions for the effective storage and …

Go to article

Failure Characterization Of A Fiber Reinforced Ceramic Matrix Composite With Circular Holes, Daniel E. Bullock Dec 1991

Failure Characterization Of A Fiber Reinforced Ceramic Matrix Composite With Circular Holes, Daniel E. Bullock

Theses and Dissertations

The purpose of this study was to investigate the performance of a fiber reinforced ceramic matrix composite with circular holes. The specific objectives were to (1) determine the relationship between tensile failure stress and the ratio of hole diameter to specimen width, and (2) to examine the initiation and progression of damage. The ceramic matrix composite used was SiC/ 1723, composed of continuous silicon titanium carbide fibers in an aluminosilicate glass ceramic matrix. Uniaxial tensile tests were performed at room temperature on two different layups; unidirectional [0]8, and [0/90]2s symmetric. Each layup was tested at three diameter-to-width …

Go to article

Investigation Of Damage Mechanisms In A Cross-Ply Metal Matrix Composite Under Thermo-Mechanical Loading, Joel J. Schubbe Dec 1990

Investigation Of Damage Mechanisms In A Cross-Ply Metal Matrix Composite Under Thermo-Mechanical Loading, Joel J. Schubbe

Theses and Dissertations

Metal matrix composites (MMCs) are rapidly becoming strong candidates for high temperature and high stiffness structural applications such as the Advanced Tactical Fighter (ATF). This study systematically investigated the failure modes and associated damage in a cross-ply, [0/90]2s SCS6/Ti-15-3 metal matrix composite under in-phase and out-of-phase thermomechanic fatigue. Initiation and progression of fatigue damage were recorded and correlated to changes in Young's Modulus of the composite material. Experimental results show an internal stabilization of reaction zone size but degradation and separation from constituent materials under extended cyclic thermal loading. Critical to damage were transverse cracks initiating in the 90° …

Go to article

Elasto-Composition Waves In Inhomogeneous Solids, R. C. Batra, Manfred Wuttig Jan 1986

Elasto-Composition Waves In Inhomogeneous Solids, R. C. Batra, Manfred Wuttig

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Go to article

Structural Self-Shadowing And Its Effects On The Thermal-Structural Behavior Of Orbiting Trusses, Jack Mahaney Apr 1985

Structural Self-Shadowing And Its Effects On The Thermal-Structural Behavior Of Orbiting Trusses, Jack Mahaney

Mechanical & Aerospace Engineering Theses & Dissertations

The determination of structural shadowing is described. The computation of environmental heat loads for slender structural members in earth orbit is described, and two methods for finite element thermal analysis are described . The effects of self-shadowing on the thermal structural behavior of single truss members and two different trusses are presented. In each case the shadowing produces a noticeable effect on the temperature distributions on truss members, and on the deformations of the trusses.

Go to article

Curing And Flow Of Thermosetting Resins For Composite Materials Pultrusion, Howard L. Price Jr. Apr 1979

Curing And Flow Of Thermosetting Resins For Composite Materials Pultrusion, Howard L. Price Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

Fibrous composite materials for mechanical and structural applications often are expensive due to high labor costs. One economical way of making composites is pultrusion, a manufacturing process in which resin-impregnated fibers are pulled at a constant speed through a heated die which shapes the resin-fiber mass and cures the resin. Most of the work which has been done on the process has been of an empirical nature, with limited understanding of the process principles. Most of the experience with pultrusion has been gained with polyester resins and glass fibers. Very little experience has been gained with higher performance, more costly …

Go to article

First Prev Next Last