Aerospace Engineering Commons^™

Design And Preliminary Analysis Of A Morphing Flap, Ethan Wiggins

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Generator Design: A Study Of Optimized Airflow, Rachel Wattleworth

Williams Honors College, Honors Research Projects

The core goal of this project was to prototype, test, and evaluate a new type of fan for the Safran Electrical & Power air-cooled generators. The idea of a new fan being made for these two generators arose when they were not adhering to design requirements. A base mixed-flow fan was created to test on multiple generators. Upon creating a prototype, it will be tested to prove if it can increase the air flow, decrease temperatures, and increase power and life of the machines. They all proved to be successful and achieve the main objectives for this project. Data such …

Steady Flows In Annular Wedge Lid-Driven Cavities, Anandan Ganapathy

Graduate Research Theses & Dissertations

The lid-driven cavity is a well-known canonical problem in the field of analytical and computational fluid dynamics. It is comprised of a square domain of an incompressible fluid with its upper lid has a specified velocity and the remaining wall boundaries are subjected to fixed, no-slip, zero-velocity constraints. There are numerous examples found in the literature that address the well-known, stable behavior of this system, which includes a primary recirculating vortex, secondary corner vortices, and a velocity profile through the center midpoint y-axis that is shown to be dependent on the Reynolds number. In this investigation, the shape of the …

A Computational Fluid Dynamics Analysis Of The Aerodynamic Performance Of Wind Turbine, Ashkan Ostovari

Graduate Research Theses & Dissertations

Renewable energy resources are likely to be a future energy solution. Among them, the wind has gained a lot of interest. Despite the theoretical limitation in wind energy harnessing efficiency, it is, still, one of the most promising renewable resources with utilizing turbines to extract this energy. Wind turbines, based on their axis of rotation are categorized into vertical axis wind turbine (VAWT) and horizontal axis wind turbine (HAWT), which HAWT’s have shown relatively higher efficiency than VAWT’s. The aim of this thesis is first to develop a scaled-down model of a wind turbine in Computational Fluid Dynamics (CFD) environment …

Computational Study Of Flow Interactions Over A Close Coupled Canard-Wing On Fighter, Setyawan Bekti Wibowo, Sutrisno Sutrisno, Tri Agung Rohmat

International Journal of Aviation, Aeronautics, and Aerospace

There have been many attempts to improve the flying performance of a fighter. By modifying the flow that occurs along the fuselage is expected to improve the performance of the aircraft. One of the indicators of combat aircraft performance is the ability to perform maneuver movement. Adding a canard as forewing on the fighter wing configuration is considered capable of raising the ability in maneuver movement. The use of canard-delta pairs will affect the performance and aerodynamic characteristics of the plane. Wings and canards with delta configuration will make the rolled-up vortex as a lifting force producer on the aircraft. …

Urban Flow And Small Unmanned Aerial System Operations In The Built Environment, Kevin A. Adkins

International Journal of Aviation, Aeronautics, and Aerospace

The Federal Aviation Administration (FAA) has put forth a set of regulations (Part 107) that govern small unmanned aerial system (sUAS) operations. These regulations restrict unmanned aircraft (UA) from flying over people and their operation to within visual line of sight (VLOS). However, as new applications for unmanned aerial systems (UAS) are discovered, their capabilities improve, and regulations evolve, there is an increasing desire to undertake urban operations, such as urban air mobility, package delivery, infrastructure inspection, and surveillance. This built environment poses new weather hazards that include enhanced wind shear and turbulence. The smaller physical dimensions, lower mass and …

Aerodynamic Design And Exploration Of A Blended Wing Body Aircraft At Subsonic Speed, Sam Dakka Dr, Oliver Johnson

International Journal of Aviation, Aeronautics, and Aerospace

Blended Wing Body (BWB) is a novel aircraft concept which provides many different aerodynamic benefits over conventional aircrafts design. This research investigated the BWB design, L/D characteristics, surface pressure distribution and span-wise lift distribution of a BWB aircraft at low to medium subsonic speeds. A BWB model was designed, manufactured and tested in a subsonic wind tunnel to validate the CFD simulation. The results gained from the investigation proved that BWB has a L/D improvement of 9.4% than conventional aircrafts and 21% increase at medium subsonic speeds (Mach 0.6) compared to lower subsonic speeds of 25 m/sec. It was found …

A New Method For The Prediction Of The Downwash Angle Gradient, Mondher Yahyaoui Dr.

International Journal of Aviation, Aeronautics, and Aerospace

A new method for the prediction of the downwash angle gradient due to aircraft wings across the span of an aft horizontal tail in the incompressible regime is presented. The approach is quite general and accounts for all practical wing geometric parameters except for wing twist where it is shown that this parameter has very little effect on the downwash angle gradient. The method consists of an empirical law which requires the prior knowledge of three constants. These have been computed either based on experimental data when available or using numerical data obtained using the vortex-lattice method. These constants are …

Uas Flight Operations In Complex Terrain: Assessing The Agricultural Impact From Hurricane Maria In The Central Mountainous Region Of Puerto Rico, Kevin Adkins

Publications

Hurricane Maria struck Puerto Rico in September 2017 as a Category 4 storm causing major damage to infrastructure, agriculture and natural ecosystems, as well as the loss of many lives. Among the crops hardest hit was coffee, one of the most important crops in Puerto Rico. As a perennial system, coffee takes various production forms along a gradient from high shade/biodiversity coffee farms to low shade coffee monocultures and therefore offers an ideal means for the study of resistance and resilience of an agroecosystem to weather and climate disturbance. During the summer of 2018, 14 impacted farms across the production …

Dynamic Response Of A Hingeless Helicopter Rotor Blade At Hovering And Forward Flights, Pratik Sarker

LSU New Orleans Theses and Dissertations

The helicopter possesses the unrivaled capacity for vertical takeoff and landing which has made the helicopter suitable for numerous tasks such as carrying passengers and equipment, providing air medical services, firefighting, and other military and civil tasks. The nature of the aerodynamic environment surrounding the helicopter gives rise to a significant amount of vibration to its whole body. Among different sources of vibrations, the main rotor blade is the major contributor. The dynamic characteristics of the hingeless rotor consisting of elastic blades are of particular interest because of the strongly coupled equations of motion. The elastic rotor blades are subjected …

Cfd Modeling Of Smoke Movement In An Atrium, Robin Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

The purpose of this paper is to better understand the behavior of smoke movement in an atrium. Thus gives first responders and civilians in and out of building a better understanding

With the advancements of modern technology, computers and softwares make simulation models possible such as fire models to simulate fire and smoke movements. In this paper, a computational fluid dynamic (CFD) software Fire Dynamic Simulator (FDS) is used to conduct a series of atrium tests to investigate the effectiveness of smoke exhaust systems. FDS solves the Navier-Stokes equations appropriate for low speed flows (Ma < 0.3) with an emphasis on smoke, heat transport and CO2 concentrations from fires. The default turbulence model used in FDS simulation is the Large Eddy Simulation (LES), which is the solution of Navier-Stokes equations at low speed.

The compartment tested was 9 …

Rotating Mount For Complex Fluid Flow Research, Kirsten Murphy

Honors Theses

Fluid flow around rotating objects is mathematically complex and there is currently limited experimental data on the subject. To make Western Michigan University capable of this research, a rotating wind tunnel mount was developed. The mount design was integrated into the existing setup at the Applied Aerodynamics Laboratory (AAL) to allow seamless transitions between different research projects. Non-rotating and rotating disk prototypes were created from 3D-printed materials to test the mount’s capabilities. Experimental data gathered from utilizing this rotating mount was analyzed to understand the aerodynamic effects on rotating disks in a fluid stream. From testing the rotating disk prototype …

Investigating The Effect Of An Upstream Spheroid On Tandem Hydrofoils, Joel Tynan Guerra

Master's Theses

This thesis documents a series of three dimensional unsteady Reynolds Averaged Navier-Stokes CFD simulations used to investigate the influence of an upstream prolate spheroid body on tandem pitching hydrofoils. The model is validated by performing separate CFD simulations on the body and pitching hydrofoils and comparing results to existing experimental data. The simulations were run for a range of Strouhal numbers (0.2-0.5) and phase differences (0-π). Results were compared to identical simulations without an upstream body to determine how the body affects thrust generation and the unsteady flow field.

The combined time-averaged thrust increases with Strouhal number, and is highest …

A Computational Fluid Dynamics (Cfd) Analysis Of The Aerodynamic Effects Of The Seams On A Two-Dimensional Representation Of A Soccer Ball, Allen R. Rohr

Master's Theses

Most major sports today use a dedicated ball or projectile with specific shape, size, and surface geometry, except for soccer. Over the history of the sport, the surface geometry and design stayed relatively unchanged, sewn together using 32 pentagonal and hexagonal panels. However, recent innovations in panel designs differ substantially from the traditional 32 panel ball. The effects these new designs have on the aerodynamic characteristics of the ball have remained largely unknown, even with the influx of experimental research completed in the past decade. Experimental studies have been broad in scope, analyzing an entire ball in wind tunnels or …

Bi-Stability In The Wakes Of Platooning Ahmed Bodies, Daniel M. Stalters

Master's Theses

Autonomous heavy vehicles will enable the promise of decreased energy consumption through the ability to platoon in closer formation than is currently safe or legal. It is therefore increasingly important to understand the complex and dynamic wake interactions between vehicles operating in close proximity for aerodynamic gains. In recent years, a growing body of research has documented a bi-stable, shifting wake generated behind the Ahmed reference bluff body. At the same time, studies of platooning Ahmed bodies have focused on changes to the body forces and moments at different following distances or lateral offsets, typically based around time-averaged measurements or …

Control Driven Scaling Effects Of Motor And Rotors For Urban Air Mobility Design, Agustin A. Giovagnoli

Doctoral Dissertations and Master's Theses

Through this thesis research the problem of controllability and propulsion associated with scaling-up consumer drones to vehicles that may carry significantly larger payloads, including passenger will be analyzed and tested. Controllability is mainly compromised due to the increasing response time of a larger rpm controlled rotor. This requires a more powerful motor, which translates into heavier and larger devices compromising the thrust-to-weight ratio. Collective pitch control at constant rpm is proposed as a first approach to mitigate the controllability problem, and it is tested in a MATLAB Simulink environment. This solution, linked to a Non-linear Dynamic Inversion controller, is simulated …

Air Temperatures Tutorial, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

A Numerical And Experimental Evaluation Of The Turbulent Heat Flux In A Heated Jet In Crossflow, Michael R. Borghi Jr.

Doctoral Dissertations and Master's Theses

The injection of fully-developed turbulent heated air from a tube into a cooler turbulent duct flow is examined, as an analogy to film cooled turbine blades. Scale Resolving Simulations (SRS) are used to examine the flow numerically. A Detached Eddy Simulation (DES) methodology is examined but found to be ineffective at correctly capturing the physics of the flow. A Large Eddy Simulation (LES) numerical model is developed and applied in which tube and duct turbulence inflow effects are emulated using a divergence-free synthetic eddy method (SEM). The LES sensitivity to the synthetic inflow turbulence is examined with a series of …

Liquid Jet Penetration And Breakup In A Free Supersonic Gas Jet, Hansen Jones

LSU Master's Theses

In the testing of today’s rocket engines, both on large scale vertical test stands and smaller subscale horizontal component testing stands, it is extremely important to be able to accurately quantify and mitigate the thermal and acoustic loads the engines will generate on test stand infrastructure. Due to the large number of parameters that must be considered for many cases, development of a multi-phase computational code is under way to properly analyze and design water spray cooling systems used at NASA’s Stennis Space Center (SSC) and across other NASA centers. As such, a small-scale experiment has been conducted at Louisiana …

Computational Aerodynamics And Anatomical Characterization Of Laryngotracheal Stenosis In Children, William Poynot

LSU Master's Theses

Laryngotracheal stenosis (LTS) is a health condition in which an obstruction in the upper trachea can cause breathing difficulties and increased incidence of infection, among other symptoms. Occurring most commonly due to intubation in infants, LTS often requires corrective surgery. Currently, clinical methods of assessing the blockage region are simplistic and subjective, and it is challenging to determine the most effective surgical strategy for any given patient. In the present work, a comprehensive methodology is proposed for characterizing the stenosis region both in terms of its anatomical parameters and its corresponding aerodynamic properties. The combination of computational fluid dynamics (CFD) …

Design Of A Heavy Lift Rc Aircraft - Society Of Automotive Engineers (Sae) Aero Design® West Competition Team, Jiyoung Hwang, Phillip Nielsen

Undergraduate Research Symposium - Prescott

The SAE Aero West design competition challenges undergraduate students to design and build an RC aircraft that will fly with the maximum number of passengers and luggage possible. The ERAU SAE team focuses on simulation-based research and project methods such as Computational Fluid Dynamics (CFD), aircraft optimization, and Finite Element Analysis (FEA). Designing and manufacturing a well-designed heavy lift aircraft and competing with other groups will give experience in solving engineering problems. The Aerodynamics team is currently focusing on score optimization, aircraft performance and configuration. The propulsion team is constructing a test rig to test various propellers and motors to …

Thermochemical Non-Equilibrium Models For Weakly Ionized Hypersonic Flows With Application To Slender-Body Wakes, Matthew P. Clarey

Theses and Dissertations

The current resurgence of interest in hypersonic technologies has warranted an inquiry into the commonly employed thermochemical non-equilibrium models within computational fluid dynamic (CFD) simulations. Additionally, research has historically focused on forebody flowfields, while studies of the complex wake structure have remained elusive. Although the forebody is of significance for vehicle analysis, the wake presents many exploitative characteristics. This dissertation aimed to address these two deficits. First, two three-temperature non-equilibrium models were developed, increasing the fidelity of hypersonic solutions above that of the legacy two-temperature model. The models were then investigated via zero-dimensional simulations, to detail the non-equilibrium processes, and …

An Analysis Of Harmonic Airloads Acting On Helicopter Rotor Blades, Iftekhar A. Riyad

LSU New Orleans Theses and Dissertations

Rotary wing aircrafts in any flight conditions suffer from excessive vibration which makes the passengers feel uncomfortable and causes fatigue failure in the structure. The main sources of vibration are the rotor harmonic airloads which originate primarily from the rapid variation of flow around the blade due to the vortex wake. In this thesis, a mathematical model is developed for rotor blades to compute the harmonic airloads at rotor blades for two flight conditions vertical takeoff and landing, and forward flight. The sectional lift, drag, and pitching moment are computed at a radial blade station for both flight conditions. The …

Design Of Selectively Compliant Morphing Wind Turbine Blade Section Using Bistable Laminate For Passive Load Alleviation, Abhishek Chopra, Dr. Andres Arrieta, Janav Udani, Jose Rivas Padilla

The Summer Undergraduate Research Fellowship (SURF) Symposium

The design of passively controlled compliant morphing structures for large scale wind turbine blades has been of interest due to the inherent advantages of lower mass and reduced complexity over their active counterparts. Previous studies have indicated that embedding a locally bi-stable element within the turbine blade section successfully allows for achieving passive load alleviation. The embedded bi-stable member switches from one stable state to another at a critical aerodynamic load. This local structural change results in a global shift in the aeroelastic response of the blade section. Building on these preliminary results, this research investigates a two- dimensional wind …

Flow Measurement Using Electron Beam Flourescence, Richard Brookes, Andrew Strongrich, Anthony G Cofer, Alina Alexeenko

The Summer Undergraduate Research Fellowship (SURF) Symposium

Low density, high-speed flows are of interest to many research areas including, spacecraft thrusters, hypersonic vehicle control, and atmospheric re-entry studies. Measurement of low-density gas flows by traditional methods such as Schlieren Photography or Particle Image Velocimetry is often not possible. In order to yield new information about gas behavior at low densities the technique of electron beam fluorescence is being re-evaluated. By recreating previous electron beam fluorescence setups used to measure density, the experiment operating parameters including beam strength and density ranges are assessed and a foundation can be built for further experimentation. Comparing intensity plots of imaged flows …

Parametric Study Of Aerodynamic Performance Of An Airfoil With Active Circulation Control Using Leading Edge Embedded Cross-Flow Fan, M.A. Qayyum Mazumder

Doctoral Dissertations and Master's Theses

A concept of a cross-flow fan (CFF) embedded near the leading edge of an airfoil to actively control the boundary layer for lift and thrust enhancement has been proposed. The design places a cross-flow fan near the leading edge of an airfoil and flow is drawn in from the pressure side of the airfoil, energized and expelled out to the suction side near the leading edge. This CFF system simulates the active boundary layer control by blowing commercial computational fluid dynamics (CFD) code ANSYS Fluent is employed to perform 2-D calculations based on various parameters of the CFF and compared …

The Development And Validation Of Sinatra: A Three-Dimensional Direct Simulation Monte Carlo (Dsmc) Code Written In Object-Oriented C++ And Performed On Cartesian Grids, David Matthew Galvez

Master's Theses

The field of Computational Fluid Dynamics (CFD) primarily involves the approximation of the Navier-Stokes equations. However, these equations are only valid when the flow is considered continuous such that molecular interactions are abundant and predictable. The Knudsen number, $Kn$, which is defined as the ratio of the flow's mean free path, $\lambda$, to some characteristic length, $L$, quantifies the continuity of any flow, and when this parameter is large enough, alternative methods must be employed to simulate gases. The Direct Simulation Monte Carlo (DSMC) method is one which simulates rarefied gas flows by directly simulating the particles that compose the …

Experiments Of Propeller-Induced Flow Effects On A Low-Reynolds-Number Wing, Gavin K. Ananda, Robert Deters, Michael S. Selig

Publications

Novel findings are discussed in this paper that will be especially beneficial to designers and modelers of small-scale unmanned air vehicles and high-altitude long-endurance vehicles that both operate at low Reynolds numbers (Re = 50,000-300,000). Propeller-induced Oow effects in both tractor and pusher configurations on a recta ngular wing using the Wortmann FX 63-137 airfoil (a common low-Reynolds-number high-lift airfoil) are presented in this paper . Significant performance benefits can be found for a wing in the tractor configuration. Experiments, including trip tests and upper-surface oil Dow visualization, show and verify that the propeller slipstream induces early transition to turbulent …

Characterization Of A Turbulent Boundary Layer In Open Channel Flow Using Particle Image Velocimetry, Mathew James Stanek

Electronic Theses and Dissertations

Turbulent boundary layers are influential in numerous applications (e.g. naval architecture, ocean engineering, sediment transport, etc.), yet considerable knowledge gaps still exist. Boundary layers are regions where transfer of mass, momentum, energy, and heat occur within the interface between a fluid and a solid, or between two fluids. Utilization of optical flow measurement techniques to measure the velocity field with high spatial resolution enables non-intrusive investigation of the complex fluid dynamics of boundary layers. In this study two-dimensional Particle Image Velocimetry was employed to investigate, primarily, the overlap layer of a turbulent boundary layer developed in the recirculating flume facility …

Fuel Flow Reduction Impact Analysis Of Drag Reducing Film Applied To Aircraft Wings, Damon Resnick, Chris Donlan, Nimish Sakalle, Cody Pinkerman

SMU Data Science Review

In this paper, we present an analysis of flight data in order to determine whether the application of the Edge Aerodynamix Conformal Vortex Generator (CVG), applied to the wings of aircraft, reduces fuel flow during cruising conditions of flight. The CVG is a special treatment and film applied to the wings of an aircraft to protect the wings and reduce the non-laminar flow of air around the wings during flight. It is thought that by reducing the non-laminar flow or vortices around and directly behind the wings that an aircraft will move more smoothly through the air and provide a …