Aerospace Engineering Commons^™

A Numerical Study Of High-Speed Missile Configurations Using A Block- Structured Parallel Algorithm, Douglas C. Blake

Theses and Dissertations

A numerical analysis of the aerodynamic phenomena associated with the high-speed flight of a sharp-nosed, four-finned, high-fineness ratio missile using a block-structured, parallel computer algorithm is presented. The algorithm, PANS-3EM, utilizes a second-order-accurate, shock-capturing, Total Variation Diminishing scheme and incorporates a Baldwin-Lomax turbulence model. PANS-3EM allows for extreme flexibility in the choice of computational domain decomposition and computing machine of implementation. Developmental work consists of conceptualization and verification of the algorithm as well as parallel performance and scalability studies conducted on a variety of computing platforms. Using PANS-3EM, the aerodynamic characteristics of the missile are investigated. Drag and pitching moment …

Wake Passage Effects On The Losses In A Linear Turbine Cascade, James A. Braunschneider

Theses and Dissertations

A linear turbine cascade was used to investigate the effects of wake passage due to stator-rotor interaction. The wakes were modeled by passing 1.98 mm (0.078 in) diameter bars upstream of a linear cascade blade row. Total pressure loss coefficients, mass averaged total pressure loss coefficients and velocities were used to characterize the effects of wake passage. Bar passing frequencies of 80, 160, 320 bars/sec were tested. These frequencies were tested, with the bars at 6.35 mm (0.25 in) intervals and at two Reynolds numbers, 341, 000 and 45,5000 Bar spacings of 12.7 mm (0.5 in), and 89 mm (3.5 …

Off-Design Performance Of Crenulated Blades In A Linear Compressor Cascade, Michael J. Costello

Theses and Dissertations

The effects of using compressor blades with a crenulated (notched) trailing edge in a low aspect ratio (AR= 1) linear compressor cascade at four incidence angles (-1.08°, +4.49°, +9.32° and +12.44°) were investigated. Blade performance and wake mixing characteristics for crenulated blades were compared with similar data for blades with a straight trailing edge. A seven-bladed cascade was operated with a flow Mach number of 0.4 and a blade chord Reynolds number of 4.1 (10)⁵. The diffusion factor ranged from 0.22 to 0. 42 and strong three-dimensional flow effects were present. Total pressure losses were measured with a …

Effects Of Crenulations On Three Dimensional Losses In A Linear Compressor Cascade, William L. Spacy Ii

Theses and Dissertations

An experimental investigation into the effect of compressor blade trailing edge geometry on three-dimensional flows in a linear cascade was conducted at the AFIT linear cascade test facility. Hot-wire/hot-film anemometry along with total pressure instrumentation was used to analyze crenulation generated vortices and their interaction with the three-dimensional flows in the cascade. The effects of this interaction on the performance parameters associated with the cascade were quantified. The results-indicate that wake mixing is better for crenulated trailing edges and that the precise geometry of the crenulations is critical to performance. One crenulation geometry was found to increase wake mixing while …

A Numerical Determination Of Bifurcation Points For Low Reynolds Number Conical Flows, Larry K. Waters

Theses and Dissertations

It has long been established that supersonic flow over axisymmetric conical bodies at high angles of attack tend to develop a side force due to vortical asymmetry. One of the proposed reasons for the asymmetry is a bifurcation point in the solution of the Navier-Stokes equations. This study investigated the possible existence of a bifurcation point in the Navier-Stokes equations for subsonic flow. Newton's method, with gauss elimination, was used- to solve the steady-state, viscous, compressible Navier-Stokes equations in spherical coordinates assuming conical similarity.

Rendering Of Three-Dimensional Data Sets Derived From Finite-Difference And Spectral Methods, Paul A. Schubert

Theses and Dissertations

The timely visualization of three-dimensional data sets and the advantages of using a spectral method solution versus a finite-difference method solution in rendering isosurfaces is described. The Beam-Warming numerical algorithm, which uses implicit-approximate-factorization, is used to generate the steady-state solutions for a model diffusion-convection problem. The Chebyshev collocation operator is used to evaluate the right-hand side of the Beam-Warming algorithm for the spectral solution. Comparing the model problem results with the exact solution, the spectral series solution is truncated to the same degree of accuracy as the finite-difference for comparison of rendering times. The rendering algorithm employs octrees to efficiently …

Simulation Of Vertical Tail Buffet In Internal Vortex Breakdown Flows, Mark William Flanagan

Mechanical & Aerospace Engineering Theses & Dissertations

Computational simulation of vertical tail buffet in an internal vortex breakdown flow is considered. The fiuid-flow problem is formulated using the full, compressible, unsteady Navier-Stokes equations which are solved using an implicit, flux-difference splitting, finite volume scheme. The fluid-flow problem is solved in a configured circular duct using quasi-axisymmetric assumptions to simplify the flow equations. A plate is placed transverse to the incoming flow. Solution of the flow in the duct is performed with and without a rigid plate, and with and without an elastic plate. The elastic response of the plate is calculated assuming that it is a cantilever …

Simultaneous Aerodynamic Analysis And Design Optimization, Satish Venkatasubra Mani

Mechanical & Aerospace Engineering Theses & Dissertations

An efficient approach for simultaneous aerodynamic analysis and design optimization is presented. Using this approach, the expensive procedure of performing complete steady— state flow analyses at every design-optimization step is avoided, thus addressing the challenge of incorporating computational fluid dynamics software into efficient gradient—based optimization techniques for aerodynamic design. An adjoint—variable method is introduced to nullify the effect of an increased number of design variables in this problem formulation. This approach is successfully tested on two quasi—one—dimensional nozzle—flow problems: a fully supersonic flow, and also a transonic flow with a normal shock. The algorithm is implemented using the direct Newton—iteration …

Computation Of The Aerodynamic Characteristics Of A Subsonic Transport Aircraft Using A Panel Method, Lillianne Plaster Whitelock Troeger

Mechanical & Aerospace Engineering Theses & Dissertations

An advanced low-order panel method, VSAERO, is applied to a full-configuration transport aircraft. Wing pressure distributions as well as lift, drag, and pitching moment coefficients calculated for the full computational configuration are compared with experimental data. In addition, partial configurations are evaluated computationally to determine the relevance of certain complex aircraft components to the computations. It is shown that the wing-surface pressure distributions and pitching moment coefficient are well predicted by VSAERO. The lift coefficient is consistently overpredicted by the code.

A Comparison Of Computational And Experimental Data For A Subscale High Speed Propulsive Nozzle At Low Mach Numbers, Yonghee Hyun

Theses and Dissertations

This computational study of a hypersonic sub-scale nozzle/cowl configuration compares numerical solutions with experimental data for nozzle performance at off design conditions (subsonic through supersonic Mach numbers. A combination of Van Leer and Roe flux-splitting algorithms was used to solve the flow field. The explicit formulation assumed laminar planar flow and the perfect gas equation of state. A validation for the numerical algorithm was accomplished by comparing with experimental data for a variety of cases. Grid refinement, geometry, and operating conditions all influenced the comparison of the experimental and computational data. Generally, as the Mach number and nozzle pressure ratio …

Hoph Bifurcation In Viscous, Low Speed Flows About An Airfoil With Structural Coupling, Mark J. Lutton

Theses and Dissertations

The locations of Hopf bifurcation points associated with the viscous, incompressible flow about a NACA 0012 airfoil with structural coupling are computed for very low Reynolds numbers (<2000). A semi-implicit, first-order-accurate time integration algorithm is employed to solve the stream function-vorticity form of the Navier-Stokes equations. The formulation models the inclusion of simple structural elements affixed to the airfoil and captures the resulting airfoil motion. The equations describing the airfoil motion are integrated in time using a fourth-order Runge-Kutta algorithm. The dissertation is divided into two parts. In part one, numerical experiments are performed in the laminar regime to determine if the structural model of the airfoil has an effect upon the location of the Hopf bifurcation point when compared with the fixed airfoil. Results are reported for a variety of structural characteristics, including variations of torsional and linear spring constants, inertial properties, structural coupling, and structural damping. The structure of the solution space is explored by means of phase plots. In part two, the Baldwin-Lomax turbulence model is implemented to model turbulent flow. A numerical effort is made to predict the onset of unsteady flow.

Simplified Jet-A Kinetic Mechanism For Combustor Application, Bahman Ghorashi, Chi-Ming Lee, Krishna Kundu

Scholarship Collection

Successful modeling of combustion and emissions in gas turbine engine combustors requires an adequate description of the reaction mechanism. For hydrocarbon oxidation, detailed mechanisms are only available for the simplest types of hydrocarbons such as methane, ethane, acetylene, and propane. These detailed mechanisms contain a large number of chemical species participating simultaneously in many elementary kinetic steps. Current computational fluid dynamic (CFD) models must include fuel vaporization, fuel-air mixing, chemical reactions, and complicated boundary geometries. To simulate these conditions a very sophisticated computer model is required, which requires large computer memory capacity and long run times. Therefore, gas turbine combustion …

Experimental Investigation Of The Aerodynamics Of Independently Rotating Cylindrical Shells, Walter C. Howerton

Theses and Dissertations

The purpose of this thesis was to investigate experimentally the aerodynamic forces on two adjacent, independently rotating cylinders in a cross- flow. This investigation involved a force measurement setup which had the two cylinders mounted on a common support shaft, extending beyond the span of the wind tunnel test section, and supported by spoke rings with strain gages in the vertical and horizontal directions. This setup proved capable of measuring aerodynamic forces. The lift on the independently rotating cylinders was found to increase as one cylinder's angular speed increased while the other's remained constant, and decrease as the relative angular …

The Effects Of Viscosity On A Conically Derived Waverider, James A. Mundy

Theses and Dissertations

This study investigated the effects of the interaction between the viscous boundary layer and the shock wave produced by a Mach 10 inviscid optimized waverider. An implicit, Roe flux-splitting algorithm, developed by WL/FIMM, was used to solve the flow field. A validation for the inviscid version of the CFD algorithm was accomplished by comparing the numerical -data produced by the CFD code to the analytic results derived by Rasmussen, and by comparison to results of the explicit version of the same Roe flux-splitting code. The computational results compared favorably. The inviscid case studied using the implicit code produced results identical, …

A Wind Tunnel Study Of Magnus Effects On A Differentially Rotating Missile, Karen A. Naselius

Theses and Dissertations

This study investigates magnus effects on a non-firmed missile model which had three axially rotating sections that span at different rates. Five spin cases are examined; the mid section spinning only; the front and rear sections spinning only; all section spinning at the same speed; all sections spinning in the same direction with the mid section spinning at an additional ten revolutions per second; and all sections spinning with the mid sections spinning the opposite direction at an additional ten revolutions per second. These five cases are tested at three different spin rates for two different wind tunnel velocities. Since …

Dynamics Of A Split Torque Helicopter Transmission, Majid Rashidi, Timothy Krantz

Scholarship Collection

A high reduction ratio split torque gear train has been proposed as an alternative to a planetary configuration for the final stage of a helicopter transmission. A split torque design allows a high ratio of power-to-weight for the transmission. The design studied in this work includes a pivoting beam that acts to balance thrust loads produced by the helical gear meshes in each of two parallel power paths. When the thrust loads are balanced, the torque is split evenly. A mathematical model was developed to study the dynamics of the system. The effects of time varying gear mesh stiffness, static …

Effect Of Nonuniform Entrance Flow Profile On Hypersonic Nozzle Pitching Moment, Sandra L. Snelling

Theses and Dissertations

The Scramjet Hypersonic Nozzle (SCHNOZ) parabolized Navier-Stokes computer code was used to model turbulent, chemically reacting flow present in a hypersonic nozzle. Two nozzle configurations were considered, an isolated nozzle (no external flow) and a nozzle with a finite length cowl. A single nonuniform entrance flow profile was generated and an equivalent uniform flow profile calculated for input into the nozzle code. Uniform and nonuniform cases for each nozzle were run using both frozen and finite rate chemistry. An increased grid resolution in the computer code was necessary to eliminate numerically induced anomalies in the results of the nonuniform cases …

Investigation Of The Influence Of Rotary Aerodynamics On The Study Of High Angle Of Attack Dynamics Of The F-15b Using Bifurcation Analysis, Ralph D. Fero

Theses and Dissertations

The purpose of this research was to use bifurcation analysis to investigate the effectiveness of rotary balance data in the prediction of aircraft spin behavior as both a stand alone representation of a model's aerodynamic data and in a conventional hybrid model. using the foundation of a previously developed model of the F-15B, the rotary balance aerodynamic force and moment data were implemented as a function of angle of attack, angle of sideslip, non-dimensional rotation steady state rate and the control surface deflections. Bifurcation diagrams were developed as a function of alpha vs. deflection angles of, the rudder, stabilator, and …

High-Resolution Tvd Schemes For The Analysis Of 1. Inviscid Supersonic And Transonic Flows. 2. Viscous Flows With Shock-Induced Separation And Heat Transfer, Mark A. Driver

Theses and Dissertations

Application of TVD schemes to both inviscid and viscous flows is considered. The mathematical and physical bases of TVD schemes are discussed. First and second-order accurate TVD schemes and a second-order accurate Lax- Wendroff scheme are used to compute solutions to the Riemann problem in order to investigate the capability of each to resolve shocks, rarefactions, and contact surfaces. Second-order finite-volume and finite-difference TVD schemes are used to obtain solutions to inviscid supersonic and transonic cascade flow problems. TVD schemes are shown to be superior to the Lax-Wendroff family of schemes for both transient and steady-state computations. TVD methodology is …

Thermal Nonequilibrium Effects On Turbine Cascade Aerodynamics, Jill L. R. Shaw

Theses and Dissertations

The AFIT Total Variation Diminishing Euler Code (ATEC) was modified to include a thermal nonequilibrium model to investigate high temperature effects associated with vibrational relaxation in a transonic turbine cascade. Incorporation of this model into ATEC and creating ANTEC (AFIT Nonequilibrium TVD Euler Code) was accomplished in three steps. Steady-state solutions obtained with ANTEC were compared with those obtained with ATEC for various inlet and exit conditions. The Courant-Friedrichs-Levy criterion was held constant to ATEC; however, it required variation for ANTEC. Blade temperature profiles, temperature difference contours in the vicinity of the trailing edge and the value of the ratio …

A Comparative Study Of Numerical Versus Analytical Waverider Solutions, Gregory O. Stecklein

Theses and Dissertations

The WL/FIMM explicit, Roe flux-splitting Euler algorithm is applied to the inviscid hypersonic flow over a parabolic-top waverider configuration optimized for Mach 10 at zero degrees angle of attack. An on-design grid refinement study is conducted to determine the asymptotic nature of the optimized flight parameter L/D. A parametric study of off-design conditions is conducted to determine flow perturbation effects on HSDT waverider theory. A validation of the Euler code is conducted through a comparison of the numerical data to analytical results derived by Rasmussen. The grid refinement study shows little effect on the inviscid calculation of the optimized parameter …

An Experimental Study Of A Sting-Mounted Circulation Control Wing, Steven J. Lacher

Theses and Dissertations

This wind tunnel study investigated the lift, drag, and pitching moment of a 20% thick, 8.5% camber, partial elliptical cross-section, single blowing slot, 2.325 aspect ratio, rectangular circulation control wing. The AFIT 5-foot wind tunnel was used. Lift and drag were referenced to the wind axis. The Reynolds number was 500,000 for all tests. Angle of attack was varied from -6 to 16 degrees and the effects of pulsed blowing were investigated. Effects of tripping the Coanda jet with a small flow barrier attached spanwise along the Coanda surface were also studied. Results indicate that there is a limit on …

Linearized Dynamics Of Space Structures With Articulated Appendages, Gopichand Koganti

Mechanical & Aerospace Engineering Theses & Dissertations

The inherent difficulties of the conventional spacecraft design, which first considered the optimization with respect to structural variables and then with respect to control variables, have led to the concept of Controls-Structures Interactive Design. The success of the CSI design of Space structures without articulated appendages has prompted the extension of the CSI design to systems with articulated appendages. The presentation is of two parts, the first part deals with the derivations of the equations of motion and the second part deals with the eigenvalue/vector approximations.

Three approaches, namely: the multibody approach, the finite element based approach with hinge joints …

Finite Element Analysis Of Nonlinear Panel Flutter Of Rectangular Composite Plates Under A Uniform Thermal Load, Lain Ross Dixon

Mechanical & Aerospace Engineering Theses & Dissertations

A finite element formulation is developed to analyze large-amplitude panel flutter of arbitrarily laminated composite plates subjected to a uniform temperature change. The plates considered are anisotropic composite, thin rectangular panels. The aerodynamic pressure load is modeled through the use of the first-order piston theory. The equations of motion for the oscillating plate are determined from the principle of virtual work. Two different solution procedures are given to determine the panel motions. The first procedure, which considers only the aerodynamic load, solves the panel limit-cycle motions by employing the linearized updated-mode with a nonlinear time function (LUM/NTF) approximation. The second …

Application Of Sensitivity Analysis To The Euler Equations, Vamshi Mohan Korivi

Mechanical & Aerospace Engineering Theses & Dissertations

An approximation method is presented for efficiently predicting the changes which occur in a steady-state numerical solution of the Euler equations as a consequence of a small change in the geometric shape of the domain. The method is extended to develop a general procedure for calculating aerodynamic sensitivity derivatives with respect to variations of geometric shape. The techniques are implemented using an upwind cell centered finite volume formulation, and are applied to two test cases, (1) a subsonic nozzle (M_∞ = 0.85), and (2) a supersonic inlet (M_∞ = 2.0). Conventional numerical solutions are first obtained for flow …

An Experimental And Analytical Investigation Of Wing Flutter On A Trial Rotor V/Stol Aircraft, David L. Soistmann

Mechanical & Aerospace Engineering Theses & Dissertations

A wind tunnel model based on a trail rotor vehicle concept was tested for wing flutter in the subsonic flow regime. The wind tunnel model was flutter tested in the forward flight mode only. From this test it was determined that this conceptual vehicle may be susceptible to wing flutter. However, the flutter encountered was not catastrophic but was of the limited amplitude type. The trailing rotor blades were found to have a positive aerodynamic damping effect on flutter. The flutter mechanism for each flutter point was due to a coupling of the first wing bending and first wing torsion …

Effect Of Passive Flow-Control Devices On The Drug Of A Tractor-Trailer Model, Jagjit K. Ahuja

Mechanical & Aerospace Engineering Theses & Dissertations

The aerodynamic drag of tractor trailers is responsible for approximately half of the fuel consumption at highway speeds (55m.p.h.). Thus, it is important that vehicle drag be reduced in order to reduce operating costs and to conserve fuel. The purpose of the subject research conducted in the Old Dominion University Low-Speed Wind Tunnel was to determine the effect of various add-on flow-control devices, such as a cab-mounted flow deflector and gap seals between the tractor and the trailer. In addition, the effect of trailer rear-edge shaping has been studied. This was accomplished by contouring the trailer's rear end. It has …

Turbulence Scales In The Passage Of A Linear Turbine Cascade, James L. Acree

Theses and Dissertations

Convective heat transfer in a turbine cascade is examined for turbulence effects. Turbulence in the free stream is varied by injection of air through a jet-grid device upstream of the cascade. Pressure and flow patterns on the blade surface, and flow velocity in two components, are examined to determine the effect of the jet-grid. Velocity and velocity fluctuation in two components are measured. Local turbulence scales through the cascade passage are determined, and local turbulent energy dissipation rate is determined. Results indicate injection of air through the jet-grid changes the angle of incidence, and therefore changes the surface pressures and …

Analysis Of Hypersonic Blunt-Body Flows Using A Total Variation Diminishing Scheme And The Maccormack Scheme, Montgomery C. Hughson

Theses and Dissertations

An explicit second-order accurate, total variation diminishing (TVD) scheme and the MacCormack scheme are applied to the Euler equations in axisymmetric form to study hypersonic blunt body flows. The modified flux approach of Harten, with modification by Yee, for two-dimensional flows is extended to treat axisymmetric flows. Calculated flow properties for the steady state, blunt body problem such as shock standoff distance, bow shock shape, surface pressure distribution and entropy jump conditions are compared to theory, results from the MacCormack scheme, and experimental data for Mach numbers of 3.0, 4.03, 5.06, 6.03 and 8.1. Additionally, the TVD and MacCormack schemes …

Vortex Bursting Over A Unit Area Aspect Ratio Delta Wing Using Vortex Paneling Methods, Donald A. Lorey

Theses and Dissertations

A unit aspect ratio delta wing is analyzes to determine if an unsteady vortex panel method can calculate the vortex bursting of the vortex developed along the leading edge. A two-dimensional vortex panel method is used to investigate wake splitting schemes of the vortex cores that comprise the vortex sheet, or wake. The worthier of the splitting methods is later implemented into the three-dimensional wake. The weighting values of the Kutta equations are investigated for the leading edges, and are determined to be problem specific. An alternative approach to management of the wake data is presented and implemented. The delta …