Engineering Commons^™

Strength Analysis Of An Aircraft Sandwich Structure With A Honeycomb Core: Theoretical And Experimental Approaches, Sadiq E. Sadiq, Muhsin J. Jweeg, Sadeq H. Bakhy

Engineering and Technology Journal

In this paper, the strength of aircraft sandwich structure with honeycombcore under bending load was evaluated theoretically and experimentallybased on failure mode maps. A failure mode map for the loading underthree-point bending was constructed theoretically to specify the failuremodes and corresponding load. Three point bending test for aluminumhoneycomb sandwich beam has been achieved to measure the peak loadand maximum deflection. The obtained results elucidated a goodagreement between the theoretical solutions and experimental tests, wherethe error ratio was not exceeded 12%. The core height, the cell size andthe cell wall thickness were selected to explore the effect of honeycombparameters on the …

Assessing The Performance Of The Evacuated Tube Solar Collector Using Smart Curtain Through (Pso Based Pid) Controller And Nano Fluids, Hosham S.Anead, Khalid F. Sultan, Sura Abdul Jabbar

Engineering and Technology Journal

This research revealed control on Nano fluid temperature in the evacuated tube solar collector system, where Nano fluids used in ETSC as working fluid to increase heating system thermal efficiency. Smart curtain was used to shadow the evacuated tube solar collector and to control the temperature of the Nano fluid in heating or cooling condition which is moved by the stepper motor which is programmed to move through the Arduino board using an artificial intelligence method such as (PSO based PID) controller method . Where the curtain's main idea is to control the polarization of the sun's radiation, the work …

Treatment Of Iraqi Municipal Wastewater By Up-Flow Anaerobic Sludge Blanket Reactor Uasb, Khairi R. Kalash, Majid A. Dixon, Hussein Ir. Sultan, Raad A. Ali

Engineering and Technology Journal

In this work, the Upflow Anaerobic Sludge Blanket “UASB” reactor treated effluent wastewater to investigate the process performance on a pilot plant scale. Municipal wastewater at high and medium strength with different organic load rate OLR (0.6-9) kg COD m-3day-1 with the flow of 20 l/h, up-flow velocity 0.4 m/h, hydraulic retention time HRT 9 h at a temperature of (20-30 ºC) was evaluated. The wastewater concentration, including TSS, COD was measured, and the removal efficiencies of chemical oxygen demand (COD) and total suspended solid TSS were calculated and summarized as 45-85% and 70-75%, respectively, depending on organic load rate …

A Brief Survey On Modern Iris Feature Extraction Methods, Hanaa M. Ahmed, Mohammed A. Taha

Engineering and Technology Journal

This paper presents a survey of some of the most recent research work on the extraction phase of the Iris recognition system. Iris biometric system has been used for person recognition in wide applications where person identity authentication required for its stability and uniqueness as compared to other biometric systems. Iris based recognition systems consist of stages are Iris localization, normalization, feature extraction, and matching. The extraction of features influences the precision and reliability of the biometric system, so several methods have been used.

Effect Of Pulse Electric Field On Water Characteristics As A Disinfection Function In Filtration Unit, Ghassan Abukhanafer, Alaa H. Al-Fatlawi, Hassan H. Joni

Engineering and Technology Journal

This paper studied the impact of the addition of pulse electric-filed low voltage (PEF-LV) in the filtration process by designing, constructing, and operating a pilot-scale. The Disinfectant process (DP) demonstrated several benefits in terms of efficiency and ease of application, without the use of any chemical additive. This system contains two pairs of silver mesh electrodes inside the filtration column test with a low pulse voltage for killing microorganisms. The parametric effects of DP performance, such as alternating current pulse frequency and the voltage applied were investigated. The effect of PEF-LV on the biological, physical, and chemical characteristic of water …

Influence Of Microfibers Additive On The Self-Healing Performance Of Mass Concrete, Alaa Z. Dahesh, Farhad M. Othman, Alaa A. Abdul-Hamead

Engineering and Technology Journal

Because cracks are the main problem of mass concrete, this paper investigates an experimental study on the effect of polypropylene microfiber (PPMFs) on self -repair behavior of mass concrete, through study the microstructure, workability, physical, and mechanical properties of mass concrete. PPMFs with a diameter of 18 μm add in different percentages (0, 0.5, 1 and 1.5) % of cement weight. Where the prepared mixture ratio was (1:2:4.8) and the water-cement ratio (W/C) was 0.4. Also, 0.6% of Superplasticizer (SP) % of cement weight to all concrete mixtures was added. In this study, an SEM analysis used to observe the …

Parametric Study On Buckling Behavior Of Aluminum Alloy Thin-Walled Lipped Channel Beam With Perforations Subjected To Combined Loading, Dalya S. Khazaal, Hussein M. Al-Khafaji, Imad A. Abdulsahib

Engineering and Technology Journal

The objective of the research presented in this paper is to investigate the buckling behavior of a perforated thin-walled lipped channel beam subjected to combined load. A nonlinear finite element method was used to analyze the buckling behavior of the beam. Experimental tests were made to validate the finite element simulation. Three factors with three levels for each factor were chosen to examine their influence on the buckling behavior of the beam and these factors are: the shape of holes, opening ratio and the spacing ratio of . The finite elements outcome was analyzed by using Taguchi method to identify …

Thermal Investigations Of Double Pass Solar Air Heater With Two Types Of Porous Media Of Different Thermal Conductivity, Jalal M. Jalil, Shrooq J. Ali

Engineering and Technology Journal

This study describes an experimental investigation of the thermal efficiency of stainless steel mesh and steel wool as a porous medium in the lower channel of a double pass solar air heater. An experimental setup was planned and developed. Various types of porous media with high thermal conductivity and with different porosities have been tested. The effects of the porosity of wire mesh, the thermal conductivity of porous media, mass flow rate, and the intensity of radiation have been studied. Experimental results show that thermal efficiency with using porous media is greater than without using porous media. When used steel …

Evaluation Of The Hydrodynamic Pressure Effect Of Cylindrical Liquid Storage Tank On The Granular Soil Behavior Under Seismic Excitation, Ahmed A. Hussein, Mohammed A. Al-Neami, Falah H. Rahil

Engineering and Technology Journal

Many liquid storage tanks around the world have been affected by earthquakes, and the seismic analysis of such tanks is much more complicated due to the Fluid-Structure Interaction. Besides, when the soil properties are taken into the consideration, the analysis with the Fluid-Soil-Structure Interaction becomes very complicated. In this paper, a series of shaking table tests are conducted on a model of the cylindrical water tank rested on dry granular soil and the equivalent load is considered to study the effect of hydrodynamic pressure generated in the storage water tank on the soil behavior. An experimental investigation of (1:100) scale …

Chemical Extraction Process For Producing High Purity Nanosilica From Iraqi Rice Husk, Sami A. Ajeel, Khalid A. Sukkar, Naser K. Zedin

Engineering and Technology Journal

Rice husk is considered a main agricultural waste in Iraq. High purity SiO2 NPs were produced from rice husk by enhanced precipitation and developed leaching processes for the preparation of silica from RH. In this study, pre-treatment for rice husk was with 3N HCl, and calcination at 700°C was achieved, then followed with a leaching process with (1.5, 2, 2.5, 3) N NaOH concentrations. The characterizations of the prepared SiO2 NPs were studied by X-ray fluorescence (XRF), X-ray diffraction (XRD), and atomic force microscopy (AFM). The results show that the prepared SiO2 NPs have an amorphous structure with a high …

Experimental Investigation Of Thermosyphon Thermal Performance Using Different Filling Ratio, Talib Z. Farge, Samar J. Ismael, Rawad M.Thyab

Engineering and Technology Journal

The present work investigated the thermal performance of thermosyphon by using distilled water as a working fluid at different filling ratios (50%, 60%, and 70 %). The thermosyphon was manufactured from a copper tube with outer and inner diameters (26 and 24) mm, respectively. The thermosyphon was tested experimentally at different input power (100, 200 and 300) Watt. The operating temperature of the oil was chosen below 85°C. Experimental results revealed that the filling ratio of 60% exhibited the best heat dissipation at the highest operating temperature. While the low operating temperature and 50 % filling ratio show better heat …

Effects Of Evaporator And Condenser Temperatures On The Performance Of A Chiller System With A Variable Speed Compressor, Ahmed H. Al-Hassani, Alaa R. Al-Badri

Engineering and Technology Journal

The operation and performance of heat-pump systems are affected by indoor and outdoor operating conditions. Power consumption and system efficiency are related to evaporator and condenser working pressures. Intelligent controllers such as a proportional integral (PI) controller improve the performance of variable speed refrigeration systems (VSRs) with electronic expansion valve (EEV). Evaporator and condenser pressures affect the system power consumption and efficiency. In this study, the influence of evaporator and condenser temperatures on the performance of a variable speed refrigeration system with an EEV was experimentally investigated at constant cooling load. The experimental system comprises of a rotary compressor, shell-and-coil …

Direct Shear Strength Of Rpc Member, Shahad Q. Madhlom, Hussein A. Aziz, Ammar A. Ali

Engineering and Technology Journal

In this research paper, results are obtained from Reactive Powder Concrete (RPC) push-off specimens - double L shape subjected to direct shear loading. Different parameters considered are compressive strength, percentages of steel fiber, presence of aggregate and shear reinforcement. The results show that increasing in steel fiber content starting from 0.0% and ending with 1.5% leads to increases in the shear strength by (261%) and attempt to decrease its brittleness. The presence of steel fiber content enhances and improves the tensile strength and the shear strength. Using RPC in constructing the specimens enhances the shear strength by 29.6% compared with …

Performance Evaluation Of Photovoltaic Panels By A Proposed Automated System Based On Microcontrollers, Mustafa Q. Ali, Monaf S. Tapoub, Hayder A. Dhahadc

Engineering and Technology Journal

In this paper, an automated test setup for PV panels using LabVIEW and several microcontrollers (μCs) based embedded systems has been designed, tested, and implemented. This PV testing system has been characterized as fully automated and the only human intervention required is to install the PV panel and to set the required testing conditions. Several PV panels were evaluated and tested, the obtained results showed a high degree of accuracy and conformity with several testing schemes that have been carried out numerically, manually and manufacturer specifications. The designed system is characterized by a high-performance standard with accuracy, precision, and resolution …

A Review On Microbial Fuel Cells, Baidaa A. Kitafa, Afaf J. Obaid Al-Saned

Engineering and Technology Journal

The Microbial Fuel Cell (MFC) is a bioreactor with which the chemical energy in chemical bonds of organic compounds are converted to electricity under anaerobic conditions through catalytic reactions of micro-organisms. It has been familiar for a long time that electricity can be generated directly through using bacteria to break organic matter. A microbial fuel cell can also serve in different wastewater treatment to destroy organic matter. The development of MFC technology requires a greater understanding of the microbial processes for MFCs, and their components, limitations, factors and design this system, to be simpler and large scale system developed; so …

Cosmetic Clamper, Daniel Peter Gates, Bruno Roberto Martinez, Samantha Remy, Zachary Joseph Roeber

Mechanical Engineering

Cosmetic Clamper Mechanical Engineering Senior Project was a senior project at California Polytechnic State University, San Luis Obispo in the College of Engineering, Mechanical Engineering Department. The project ran from September 2025 to June 2026. The project developed the Cosmetic Clamper device, an accessibility product designed to help individuals with unilateral upper extremity motor deficits open, use, and close cosmetic containers independently.

Buell Motorcycle Extended Swing Arm, Joseph Camuccio, Riley Clark, Vincent Sclimenti, Tristan Turcios

Mechanical Engineering

Buell motorcycle riders, including our sponsor Rick Lasko, need a way to easily and affordably manufacture and replace their swing arms with extended versions (4”, 8”, 12”, and 16”) that maintain the stock Buell aesthetic while also meeting the safety standards required for performance-intensive applications, such as drag racing. Each extended swing arm must be just as safe, strong, and rigid as the original swing arm. Currently, there is no convenient and affordable solution to this problem, which is why our sponsor, Rick Lasko, wanted a validated, repeatable manufacturing process and design that would allow riders to safely and consistently …

Capstone Review: Warn Winch Proximity Sensor, Leana Girton

University Honors Theses

This thesis reviews the mechanical engineering capstone project that designed a winch proximity sensor for WARN Industries. WARN is very interested in developing this product for market as a safety and ease-of-use accessory, and working with Portland State University was the first step in this process. A group of four mechanical engineering and four electrical engineering capstone students collaborated to research sensor types, test the selected methods, and design and build a prototype. The final design implements an inductive ring, a mechanical button, and bluetooth signaling. The project succeeded in prototyping a proximity sensor for WARN, who will have access …

A Faith And Technology Resource Hub: Building The Christian Engineer’S Bookshelf, Gayle Ermer, Derek Schuurman

University Faculty Publications and Creative Works

A wealth of material related to the interactions between faith and technology has been generated over time to help Christian engineers reflect on and evaluate their work and technology development more generally. However, there is currently no central location where this large variety of resources can easily be accessed. This paper will describe the process of developing a faith and technology resource hub. The vision for the hub is that it will include a comprehensive searchable directory of resources addressing faith and technology, as well as a browsable, organized, curated, and annotated set of webpages containing links to particularly important …

Development Of A Putting Green Manufacturing Process, Jose Andres Cepeda Santiago

Honors Theses

Our Capstone project investigates the end-to-end design, development, and production of a 6‑foot long portable putting green marketed for individuals seeking a high quality, competitively priced golf product for home or office use. The capstone project examines the full lifecycle of product creation applying manufacturing principles learned through the center of manufacturing’s coursework. From the initial concept through engineering design, market research, prototyping, manufacturing optimization, and final production the project emphasizes cross‑functional collaboration across engineering, business, and accountancy majors. Methods used to gather data included marketing surveys, CAD drawings, time studies during production runs, value stream mapping, and controlled documentation …

Challenging Stem Learning Spaces: The Paradigm Of Contemplative Traditions As The Bedrock Of Creativity And Healing, Raaghav Pandya, Christopher Emdin

Journal of Contemplative and Holistic Education

As the post-pandemic classroom and pedagogy evolve to remedy oppressive norms, young people’s mental health and alienation has taken front stage (Rahmani & Zitouni, 2022). Traditional STEM learning spaces often teach inquiry as a linear, non-deviated approach to problems about self and nature (Hrisa & Psillos, 2022). Furthermore, because our classrooms often strip students and educators of their inherent creative abilities through constant assessments, improvement scales, and market-driven expectations, classrooms cease to become places of healing (Pandya, 2021). Eastern wisdom traditions and their associated philosophies provide a unique pedagogical lens that emphasizes a deep inquiry into self, empathy, and creativity …

Portable Humidity Chamber, Calvin Wright, Ian Heilers, Sam Taylor

Honors Capstones

This engineering project, sponsored by Crandall Stats and Sensors, focuses on improving the ability to test product performance under controlled environmental conditions by designing a portable humidity chamber capable of maintaining a stable relative humidity between 20 and 80 percent with a tolerance of ±0.5 percent. Consistent humidity is crucial for evaluating how moisture influences material properties, product reliability, and long-term durability in real production environments. Because Crandall conducts testing across multiple facility locations, the chamber must also be lightweight, transportable, and easy for operators to use without specialized training. Developing such a system provides the company with a valuable …

Retrospective Analysis Of Implemented Project Management Within A Small-Scale Student Engineering Project: Beng Fountain Wars Team Case Study, Holli E. Jenkins

Biological and Agricultural Engineering Undergraduate Honors Theses

This honors thesis provides a retrospective analysis of how the 2025 inaugural University of Arkansas’s ASABE Fountain Wars Student Team could be improved through project management. Project commitment, early stakeholder influence, rich communication, and a detailed project plan are all attributes of successful projects, and the team’s strengths and weaknesses within these categories were determined through a team poll. After the poll was conducted, three methodologies, Agile, Hybrid, and Waterfall, were assessed to determine how they would effectively address the team’s weaknesses. A weighted objectives table was created to compare each methodology’s effectiveness across the management categories. The analysis revealed …

Developing Transparent Sustainability Data Systems In A Poultry And Pet Food Company: An Internship Case Study, Catherine L. Warren

Biological and Agricultural Engineering Undergraduate Honors Theses

My honors thesis examined my internship experiences and its implications on sustainability data gathering and reporting in poultry and pet food companies. It highlighted my internship projects, the skills I developed, and the connections to sustainability data transparency and reliability in a corporate environment.

In my thesis, I shared details about my internship. I described what projects I worked on, the places I visited, the hands-on experience I gained, and the different teams I worked with throughout the internship duration. I discussed the analytic and professional skills I developed through conducting a waste audit, developing Tableau dashboards, and helping to …

Enhancing Food Security In Stann Creek, Belize Using Meat Rabbits: Engineering Perspective, Lindsey Garretson

Biological and Agricultural Engineering Undergraduate Honors Theses

The purpose of this paper is to discuss the engineering perspective within the overall project of using meat rabbits to enhance food security and nutrition within Stann Creek, Belize. From the engineering perspective, the overarching goals were like the overarching project goals including the construction and materials required guide within the manual, designing potential upgrades to the design including a solar and battery system and an automatic watering system, and to design the system to be “practically sustainable” where possible. The constraints for this project included cost, the size of land dedicated for the rabbitry, and the operational and environmental …

The Developing Role Of Ai In Modern Engineering Research, Rianna Pais

The Cardinal Edge

No abstract provided.

A Transcendental Phenomenological Study Of Cognitive Overload In Manufacturing Engineers During Online Training In An Industrial Environment, Sarah J. May

Doctoral Dissertations and Projects

The purpose of this transcendental phenomenological study was to explore experiences of cognitive overload among engineers in manufacturing during digital training in industrial environments. Engineers in manufacturing manage substantial physical and cognitive demands in order to maintain safe and efficient industrial environments. In addition to these responsibilities, engineers are often expected to engage in digital training within active work settings, frequently without physical or cognitive separation from job-related tasks. A qualitative research design was employed, with data collected from 10 participants and analyzed through triangulation and thematic coding. Data collection methods included a qualitative questionnaire, individual interviews, and a letter-writing …

Enhancing Engineering Education For Students With Intellectual Disabilities Through Universal Design For Learning, Bree Jimenez, Ginevra Courtade

Journal of Science Education for Students with Disabilities

This study explores the impact of a Universal Design for Learning (UDL) aligned engineering curriculum on teacher confidence and student engagement in special education classrooms, specifically focusing on students with intellectual and developmental disabilities (IDD). The research investigates how the curriculum, combined with targeted professional development (PD), supports teachers in delivering high-quality engineering instruction. Through a mixed methods approach, including surveys, interviews, focus groups, and classroom observations, data revealed significant improvements in teacher self-efficacy, particularly in areas such as scaffolding, differentiation, and accessibility. Teachers reported increased confidence in their ability to implement engineering lessons and foster engineering mindsets in their …

Globalizing The Engineering Job Market: Optimizing Engineering Career Expos To Serve International Students, Hailey A. Hesseltine

Journal of Global Education and Research

As the United States hosts approximately one million international students annually, it becomes imperative that on-campus resources are tailored to meet the needs of this diverse student population. One on-campus resource that is crucial to student success is career services, especially considering the aspirations of many international students to secure employment post-graduation. To address this, this study aimed to understand the satisfaction levels of international engineering students with an engineering career expo in Hawaiʻi. Utilizing a combination of surveys and interviews using a neo-racism framework, international students shared their experiences from the career expo through discussion and assessment. Information given …

Can I Be An Engineer? Factors Influencing Women’S Decisions To Pursue Undergraduate Engineering Studies In The Middle East And North Africa, Rasha Malaeb, Elsa Maalouf, Aya Mouallem, Jana Sabra

Journal of Pre-College Engineering Education Research (J-PEER)

In the Middle East and North Africa (MENA), different institutional and cultural factors seemingly play a significant role in influencing women’s decisions to enroll in undergraduate engineering programs. In this work, we aim to uncover key influences that affect young women’s decisions to pursue undergraduate engineering studies in Lebanon, an Arab country in the MENA region. First, we conducted a survey during a student-led engineering summer program in 2024 at the Maroun Semaan Faculty of Engineering and Architecture at the American University of Beirut. The survey participants were 47 high school female students from diverse regions and backgrounds in Lebanon. …