Engineering Commons^™

End-Of-Life Analysis Of Nanotechnology Products, Sun Olapiriyakul

Dissertations

Previous research has shown that thermodynamic properties including melting point and specific heat capacity of nanomaterials may be higher than that of their corresponding bulk materials. The melting point elevation and specific heat capacity enhancement of nanomaterials may result in increased energy consumption and waste gases emission at the end-of-life (EOL) stage where the products containing nanomaterials are recycled by high temperature metal recovery (HTMR) process.

In this dissertation, the effect of physical characteristics of nanomaterials, referred to as physicochemical parameters, on their melting temperature and specific heat capacity was investigated. In addition, physical, chemical, and thermodynamic properties of nanomaterials …

Synthesis And Characterization Of Metal Oxide Semiconductors For Photoelectrochemical Hydrogen Production, Sudhakar Shet

Dissertations

The goal of this thesis is to investigate the properties of metal-oxide thin films on fluorine-doped tin oxide (FTO)-coated glass substrates, prepared by using radio- frequency (RF) reactive magnetron sputtering for photoelectrochemical (PEC) applications. Metal-oxide thin films as a photoelectrode are of special interest for PEC systems to produce hydrogen in an aqueous solution by solar energy due to their low cost and potential stability.

The following list represents some of the accomplishments and results of this work:

• Narrowing of N-incorporated ZnO (ZnO:N) was achieved by reactive sputtering in a O₂/N₂ mixture ambient, and ZnO:N films with …

Double Quantum Dot Photoluminescence Mediated By Incoherent Reversible Energy Transport, S. Yu Kruchinin, A. V. Federov, A. V. Baranov, T. S. Perova, Kevin Berwick

Articles

We present a theoretical study of the stationary photoluminescence of two, direct-gap, semiconductor nanocrystals, taking into account electronic excitation energy-transfer processes due to electrostatic interaction. The results obtained here allow for the incoherent reversible energy transport that occurs when the intraband relaxation rate in a quantum dot acceptor is comparable to, or less than, the energy-transfer rate. We investigate the secondary emission of two different electronic level schemes that can be realized experimentally, obtain analytical expressions for the luminescence differential cross section, and perform an analysis of its spectrum. It is shown that when excitation is not in resonance with …

Determination Of The Effects Of University Building Usage On Energy Efficiency And Recommendations For Improvement, Dana Aaron Lackey

All ETDs from UAB

Energy costs are increasing at an alarming rate, and electricity use can contribute to carbon emissions and, therefore, to global warming. With this in mind and under direction of the University of Alabama at Birmingham (UAB) Facilities Management Department, researchers conducted building occupancy surveys of UAB buildings after working hours and on weekends to evaluate occupancy by day and time and by lighting condition of unoccupied rooms. The goals of this research consisted of identifying situations in which measures such as motion sensor installation or heating and/or air conditioning shutdown or setback could result in energy and cost savings and …

Renewable Energy Integration: An Approach For Micro-Grid Optimization., Nicolas Lopez

Open Access Theses & Dissertations

This thesis explores the Renewable Energy Integration Problem beginning with a literature review on the different sources of electrical energy classified as Non-Renewable and Renewable, stating that the integration of renewable sources within the pre-existing Power-Grids is a current worldwide problem that is being addressed with different approaches.

The impossibility to exactly model the different equations relating the electric output of the renewable energy sources as they relate with meteorological factors, makes the renewable sector a stochastic component of the overall mathematical model, where it can be concluded that most of the problem is in the area of the forecast. …

Channeling University-Based Sponsored Research Into Classroom Education, Badrul H. Chowdhury

Electrical and Computer Engineering Faculty Research & Creative Works

An important mission of university-Based research that often gets overlooked is the education component. based on the 2005-2006 Electric Power Engineering Education Resources report produced by PES, tens of millions of dollars' worth of research is being conducted annually by university faculty throughout North America. While such sponsored research almost always produces master's and Ph.D. dissertations, how much of that is channeled into creating a broader impact of educating undergraduate and graduate students is of concern to many sponsoring agencies. This paper presents a summary of panel presentations that describe and discuss examples of how some faculty members have brought …

Energy Dissipation Caused By Asphalt Roadway Gouges For Use In Accident Reconstruction, Charles L. Crosby

Theses and Dissertations

In reconstruction of on-roadway vehicle accidents, roadway surface gouges and the forces and energy attributed to the related vehicle components become important keys to resolving an accurate accident reconstruction. These roadway gouge forces vary depending upon such factors as surface temperature and the velocity and geometry of the gouging mechanism. Accounting for the forces applied to vehicle components and the energy dissipated from such forces can be helpful in accident reconstruction where supporting data exists. This research documents the force necessary to create a given roadway gouge geometry. Controlled pavement gouging tests were performed using roadway surface temperature and gouging …

Pump Sequencing Optimization, John S. Allan, Kyle J. Nekimken, Spencer B. Weills

Mechanical Engineering

The purpose of this document is to demonstrate the design, production, and testing of optimum pump sequencing logic for variable frequency drive (VFD) pumps in commercial heating ventilating and air conditioning (HVAC) systems. The product will be developed by Pump Efficiency Solutions (PES), which is a group of Cal Poly students working on their senior project. The product is being developed for Trane, an industry leader in large scale HVAC systems. MATLAB™, Microsoft Excel, Pump System Improvement Modeling Tool™ (PSIM), and fluid mechanics hand calculations were used during software development. Next, we converted the program into Trane’s graphical programming language …

Agenda: Best Practices For Community And Environmental Protection, University Of Colorado Boulder. Natural Resources Law Center. Intermountain Oil And Gas Bmp Project, Colorado. Oil And Gas Conservation Commission

Best Practices for Community and Environmental Protection (October 14)

The first Intermountain BMP Project workshop, sponsored by the Natural Resources Law Center and the Colorado Oil and Gas Conservation Commission, was held in Rifle, Colorado on October 14, 2009 at the Garfield County Fairground for over 170 participants.

Speakers from Federal, state and local governments, the community, industry and environmental consultants, and conservation groups focused presentations and discussion on a greater understanding of what Best Management Practices (BMPs) are appropriate to the western slope of Colorado and how they are integrated into developments.

Composite Manufacturing Of Small Wind Turbine Blades- Utility Scale Methods Applied To Small Wind, Bryan Kyle Edwards

Master's Theses

Cal Poly, San Luis Obispo’s first wind turbine explores the methods and processes that are employed to manufacture utility scale wind turbines, and applies them to small scale wind turbines. The primary objective is to promote the development of small scale wind turbine blades in ways that resemble, as closely as possible, the construction and methods of utility scale turbine blade manufacturing. Vacuum infusion is employed to create a hollow, multi piece, lightweight design using carbon fiber and fiberglass with an epoxy based resin. A “rapid prototyping” method is developed using high density foam molds that allows short cycle time …

The Very Basics Of Sustainability - An Alternative Viewpoint, Jim Mcgovern

Other resources

This paper examines the context and meaning of the term ‘sustainability’, the factors that determine and govern climate on Earth, the population of the Earth and its trends and influencers, the requirements for sustaining life and the options that are available to humankind. Some viewpoints are presented that are alternative to ‘conventional alternative’ thinking. The author advocates keeping an open mind on all available options, including the use of oil, gas, coal, tar sands, carbon capture and sequestration, nuclear power etc., as well as the technologies that are more widely considered ‘green’ and also argues that humankind needs to face …

The Very Basics Of Sustainability - An Alternative Viewpoint (Slides With Audio) (Large File! To Speed Up Download, Right-Click On "Download" Link To Save To Own Pc.), Jim Mcgovern

Other resources

This presentation sets out the very basics of ‘sustainability’, although a definition of sustainability is not attempted. Some of the very basics are the context in which the Earth and humankind exist in space and time, the Earth’s climate, the Earth’s population and humankind’s options and choices. The author advocates keeping an open mind on all available options, including the use of oil, gas, coal, tar sands, carbon capture and sequestration, nuclear power etc., as well as the technologies that are more widely considered ‘green’. The author also argues that, in addressing the challenges that humankind faces, globally concerted effort …

Agenda: Western Water Law, Policy And Management: Ripples, Currents, And New Channels For Inquiry, University Of Colorado Boulder. Natural Resources Law Center, Western Water Policy Program

Western Water Law, Policy and Management: Ripples, Currents, and New Channels for Inquiry (Martz Summer Conference, June 3-5)

In many pockets of the American West, stresses and demands on water resources are overwhelming our capacity to effectively manage change and accommodate the diversity of interests and values associated with our limited water resources.

This event will offer an opportunity for lawyers, policymakers, and water professionals to engage the experts on the challenges and emerging solutions to the most pressing water policy and management issues of the day.

Actual And Reference Evaporative Losses And Surface Coefficients Of A Maize Field During Nongrowing (Dormant) Periods, Christopher H. Hay, Suat Irmak

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Effective water resources planning, allocation, management, and use in agroecosystems require accurate quantification of actual evapotranspiration (ET_c) during growing and nongrowing (dormant) periods. Prediction of ET_c for a variety of vegetation surfaces during the growing season has been researched extensively, but relatively little information exists on evaporative losses during nongrowing periods for different surfaces. The objectives of this research were to evaluate ET_c in relation to available energy, precipitation, and grass and alfalfa-reference ET (ET_o and ET_r) for a maize (Zea mays L.) field and to analyze the dynamics of surface coefficients …

Energy Sector For The Integrated System Dynamics Model For Analyzing Behaviour Of The Social-Economic-Climatic Model, Evan G. R. Davies, Slobodan P. Simonovic

Water Resources Research Report

The system dynamics-based energy sector described here adds a representation of energy supply and demand dynamics, and their associated carbon emissions, to a larger society-biosphere-climate model previously described in Davies and Simonovic (2008). The inclusion of an energy sector expands the earlier model considerably, and provides new avenues for its application to policy development.

Five interconnected components constitute the full energy sector: demand, resources, economics, production, and emissions. The energy demand component calculates changes over time in heatenergy and electric-energy demand as a result of economic activity, price-induced efficiency measures, and technological change. Energy resources models changes in the amounts …

Study Of Film Cooling Effectiveness: Conical, Trenched And Asymmetrical Shaped Holes, Humberto Zuniga

Electronic Theses and Dissertations

Film cooling is a technique whereby air from the compressor stage of a gas turbine engine is diverted for cooling purposes to parts, such as the turbine stage, that operate at very high temperatures. Cooling arrangements include impingement jets, finned, ribbed and turbulated channels, and rows of film cooling holes, all of which over the years have become progressively more complex. This costly, but necessary complexity is a result of the industry's push to run engines at increasingly higher turbine inlet temperatures. Higher temperatures mean higher efficiency, but they also mean that the turbine first stage operates hundreds of degrees …

Harvesting Human Exercise Power At The Cal Poly Rec Center: Exercise Bike Power Generator Ii, Jared Rounsevell, Claire M. Shubert, Matthew Snitowsky, Andrew Wong

Mechanical Engineering

The overall goal of this project is to create a workable system to harvest the power generated on exercise bikes at the Cal Poly Rec Center so that the electricity produced can eventually be sent to the power grid. Our part of the project will focus on the mechanical harvesting of this power with the goal of using the product to run the Morningstar ProStar 12V 30 amp charge controller available from the 2007 project. Eventually, the power produced could be fed to the grid in the appropriate form. The finished result of this project should be marketable to exercise …

Optimal Energy-Delay Routing Protocol With Trust Levels For Wireless Ad Hoc Networks, Eyad Taqieddin, Ann K. Miller, Jagannathan Sarangapani

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents the Trust Level Routing (TLR) pro- tocol, an extension of the optimized energy-delay rout- ing (OEDR) protocol, focusing on the integrity, reliability and survivability of the wireless network. TLR is similar to OEDR in that they both are link state routing proto- cols that run in a proactive mode and adopt the concept of multi-point relay (MPR) nodes. However, TLR aims at incorporating trust levels into routing by frequently changing the MPR nodes as well as authenticating the source node and contents of control packets. TLR calcu- lates the link costs based on a composite metric (delay …

Investigation Of Dynamic And Steady State Calculation Methodologies For Determination Of Building Energy Performance In The Context Of The Epbd, Mervin Dean Doyle

Masters

The aim of this thesis was to investigate the ability of a dynamic and a quasi-steady state calculation methodology to capture the heating and cooling aspects of a buildings energy performance in the context of the requirements of the EU Energy Performance of Buildings Directive (EPBD). Chapters 1 and 2 provide a general background review and description of the implementation of the directive’s requirements in Ireland. Chapter 3 established the usefulness and relevance of building energy benchmarks, traditional approaches to building energy performance calculation methodologies. Chapter 4 established the ability of a sample of simplified and dynamic calculation tools to …

Substrates Preparation From Woody Tropical Waste Biomass For Biohydrogen Production, Dwi Susilaningsih, Theresia Umi Harwati, Khairul Anam, Yopi Yopi

Makara Journal of Technology

Substrates Preparation from Woody Tropical Waste Biomass for Biohydrogen Production. Addressing to the global warming problem, energy crisis and pollution, hydrogen production by micro-organisms using biotechnological approach should be considered, since it fulfils the recent society requirement to safely produce, renewable and environmental friendly energy. Hydrogen is one of the most promising green energy sources, because it is easily converted to electricity and cleanly combustible. There are three types of micro-organisms for hydrogen production, the first is cyanobacteria through the photosynthesis process, the second is anaerobic bacteria, which use organic substances as electron donor and energy and convert them to …

Irrigation District Energy Survey, Charles M. Burt, Daniel J. Howes

BioResource and Agricultural Engineering

This survey was completed by ITRC on behalf of the California Energy Commission Public Interest Energy Research (PIER) Program. The purpose of the survey was to establish a benchmark for the present status of the pumping systems used by agricultural water districts in California and to determine the districts' needs. The needs discussed involve technical assistance, research grant and low-interest loan funding, and district-related policy issues. Thirty agricultural water districts were selected for the survey. These districts were selected based on energy use per acre of irrigated area, size, geographic location, and distribution infrastructure.

Mathematical Analysis Of A Geothermal System, Ivan P. Erceg

ETD Archive

The issue being examined is to design a more economical and efficient therefore superior geothermal system than currently in use in industry. Current geothermal systems are designed and built 300 feet into the ground. After researching ground temperature gradients for Ohio we found out that below 10 feet of depth, the temperature varies by 1 degree Fahrenheit per 100 feet depth. Our goal is to utilize the heat as close to the surface as possible and greatly reduce the need to dig so deeply into the ground. The procedure used to go about designing a superior geothermal system is to …

Soft Surface Roll Mechanics Parameters For Light Vehicle Rollover Accident Reconstruction, Kevin Claude Henry

Theses and Dissertations

Light vehicle rollover accidents on soft surfaces can be modeled assuming constant drag with linear motion equations and other engineering principles. The concept of using segment average results to evaluate roll mechanics parameters throughout a roll sequence, and specifically, segment duration to evaluate vehicle trajectory between ground impacts is developed. The trajectory model is presented, explained and compared to values obtained by analyzing digital video of rollover crash tests. Detailed film analysis procedures are developed to obtain data from rollover crash tests that are not otherwise documented. Elevation of the center of gravity of vehicles is obtained where instrumentation does …

Performance Characteristics Of An Innovative Wind Power System, David James Kerze

ETD Archive

This project entails a study of a wind energy recovery system that utilizes a unique three-dimensional spiral structure to amplify wind speed and direct it toward pluralities of turbines. The system is comprised of an outer spiral shell, internal support structure, turbines, and mechanisms for positioning the turbines to face the prevailing wind. Computational Fluid Dynamics (CFD) analyses were conducted to determine the wind speed amplification factors as a result of a simulated wind flow around the spiral structure. To ensure accuracy of the results, state of the art CFD techniques were applied using Gambit 2.2.30 and Fluent 6.2.16. Specifically, …

Active Minimization Of Acoustic Energy Density To Attenuate Radiated Noise From A Diesel Generator, Andrew J. Boone

Theses and Dissertations

The focus of this thesis was to use active noise control (ANC) to globally minimize the tonal and broadband noise radiating from a diesel generator enclosure. The major goal of this research was to show that minimizing the noise within the enclosure can lead to an overall sound pressure level (SPL) reduction of radiated noise. The target levels for overall SPL reduction were at least 2 dBA. The control algorithms used in this research were based on a filtered-x LMS adaptive algorithm, which minimizes energy density (ED). Both feedforward and feedback control approaches were investigated. The noise spectrum produced by …

Payback Information: It's Effect On Home Buyers Regarding Energy Efficiency, Steven E. Sparti

Theses and Dissertations

This study was conducted to find out how payback analysis would affect consumer decision making with regards to home energy efficient upgrade packages. Three different home plans were obtained from a local builder and seven different energy efficient packages were created. Using Hot2000 the heating and cooling loads were calculated for each building, with each energy efficient package, in each of the four major cardinal directions. The averages were taken and the payback information was calculated. The payback information included the increased cost of the package, the increase in the mortgage payment, the annual savings from heating and cooling bills, …

Biodiesel Basics, Czarena L. Crofcheck, Timothy S. Stombaugh, Michael D. Montross

Agricultural Engineering Extension Publications

Biodiesel is a renewable fuel for diesel engines. Biodiesel, defined by ASTM International (D6751), consists of longchain fatty acid alkyl esters and is made from renewable vegetable oils, recycled cooking oils, or animal fats. It can be used at full strength, but it is typically blended with petroleum diesel. A blend of 2 percent biodiesel and 98 percent diesel is referred to as B2. Other typical blends include B5, B10, and B20; pure biodiesel is sometimes referred to as B100. Biodiesel is safer for the environment and produces significantly less air pollution compared to petroleum diesel. Biodiesel can be produced …

Biodiesel Faq, Timothy S. Stombaugh, Czarena L. Crofcheck, Michael D. Montross

Agricultural Engineering Extension Publications

Biodiesel and other alternative fuels continue to gain popularity as petroleum fuel prices rise and we become more concerned about our environment. Introduction of these fuels raises many questions about actually using them in current equipment. The purpose of this factsheet is to address some of the common questions asked by those considering the use of biodiesel in existing diesel equipment.

Synthesis Of High-Temperature Stable Anatase Tio2 Photocatalyst, Suresh Pillai, Declan Mccormack, Michael Seery, Pradeepan Periyat, Steven Hinder, John Colreavy, Reenamol George, Hugh Hayden

Articles

In the absence of a dopant or precursor odification, anatase to rutile transformation in synthetic TiO2 sually ccurs at a temperature of 600 700 °C. Conventionally, metal oxide dopants (e.g., Al2O3 nd SiO2 are used o tune the anatase to rutile transformation. A simple methodology is reported here to extend the anatase utile transformation by employing various concentrations of urea. XRD and Raman spectroscopy were used uring thermal treatment. A significantly higher anatase phase (97%) as been obtained at 800 C with use of a 1:1 Ti(OPr)4 urea composition and 11% anatase composition is etained even after calcining …

Grain Boundary Property Determination Through Measurement Of Triple Junction Geometry And Crystallography, Brent L. Adams, D. Casasent, M. Demirel, Bassem S. El-Dasher, D. Kinderlehrer, C. Liu, I. Livshits, F. Manolache, D. Mason, A. Morawiec, W. W. Mullins, S. Ozdemir, Gregory S. Rohrer, Anthony D. Rollett, David M. Saylor, Shlomo Ta'asan, A. Talukder, Chialin T. Wu, C. C. Yang, W. Yang

Faculty Publications

This work was supported primarily by the MRSEC program of the National Science Foundation under Award Number DMR-0079996. Microstructure controls the properties of most useful materials. Thus an ability to control microstructure through the processing of materials is a key to optimization of materials performance. Most materials are polycrystalline and their grain structure is a very important aspect of their microstructure. Thanks to their complexity there is a great variety of grain boundary types even in relatively isotropic materials such as the cubic metals. Simply describing the crystallography requires five (macroscopic) parameters (e.g. disorientation and inclination). Evidently, acquiring a knowledge …