Engineering Commons^™

The Effects Of Simplifications On Isolated Wheel Aerodynamics, Sammy Diasinos, Tracie Barber, Graham Doig

Aerospace Engineering

In order to study the aerodynamic forces and flow features of rotating wheels, compromises and simplifications are often made in wind tunnel testing, and more frequently so in numerical modelling. A CFD approach similar to that commonly used in industry was utilised to investigate common assumptions involving; the influence of geometric fidelity in wheel hub regions, ground representation, the modelling of the contact patch, and the effects of rotation on separation. It was found that the separation and wake characteristics were strongly influenced by the rotation of the wheel; the separation point changed by as much as 90% compared to …

Development Of Cpanel, An Unstructured Panel Code, Using A Modified Tls Velocity Formulation, Christopher R. Satterwhite

Master's Theses

The use of panel codes in the aerospace industry dates back many decades. Recent advances in computer capability have allowed them to evolve, both in speed and complexity, to provide very quick solutions to complex flow fields. By only requiring surface discretization, panel codes offer a faster alternative to volume based methods, delivering a solution in minutes, as opposed to hours or days. Despite their utility, the availability of these codes is very limited due to either cost, or rights restrictions.

This work incorporates modern software development practices, such as unit level testing and version control, into the development of …

Cfd Simulation And Shape Optimization Of Supersonic Ejectors For Refrigeration And Desalination Applications, Liju Su

McKelvey School of Engineering Graduate Student Theses & Dissertations

The aim of this thesis is to investigate the detailed flow field inside the supersonic ejector using numerical methods and to optimize the ejector’s mixing chamber wall shape to obtain a maximum entrainment ratio (ER) in order to obtain the highest possible efficiency that can be attained by the ejector. A steam ejector applied in the cooling industry is first studied to determine the most accurate turbulence model for its supersonic jet flow field simulation with mixing with the entrained steam in the mixing chamber. A commercial Computational Fluid Dynamics (CFD) package FLUENT 14.5 along with the meshing tool ICEM …

Application Of Wray-Agarwal Model To Turbulent Flow In A 2d Lid-Driven Cavity And A 3d Lid-Driven Box, Hakop J. Nagapetyan

McKelvey School of Engineering Graduate Student Theses & Dissertations

In this thesis, various turbulence models are used for simulating internal vortical flow, both turbulent and laminar, with large recirculation by considering the flow in a 2-D lid-driven square cavity and a 3-D lid driven cubic box. The accuracy of the newly developed Wray-Agarwal (WA) one equation turbulence model is compared against two well-known industry standard turbulence models; the Spalart-Allmaras (SA) and the Shear-Stress-Transport (SST) k-ω models. The simulations are performed by numerically solving the Reynolds-Averaged Navier-Stokes (RANS) equations in conjunction with WA, SA and SST k-ω models and comparing the results with the available experimental data and Large Eddy …

Optimization Of Blalock-Taussig Shunt And Anastomotic Geometry For Vascular Access Fistula Using A Genetic Algorithm, Guangyu Bao

McKelvey School of Engineering Graduate Student Theses & Dissertations

Blalock-Taussig (BT) shunts are used for defects that affect the flow of blood from the right ventricle, through the pulmonary artery, and to the lungs. Arteriovenous (AV) fistula is one type of vascular access which is a surgically created vein used to remove and return blood during hemodialysis. Plastic grafts used in the above two reconstructions may result in areas of non-physiologic flow in the grafts leading to risk of stenosis (blocked area) and thrombosis, which is the single major cause for access morbidity. The focus of this thesis is to study BT shunts and anastomoses models using Computational Fluid …

Study Of Noise Generation Mechanisms In A Turbulent Jet Through Analysis Of Simulation Data, Adam J. Kmiec, Nitin S Dhamankar, Gregory Blaisdell

The Summer Undergraduate Research Fellowship (SURF) Symposium

Computational simulation techniques produce considerably more information about turbulent jets than experimentation and have the potential to be effective research tools for reducing the noise footprint of jet engine exhaust. There is a need to exploit the large amount of data generated by such simulations to gain a better understanding of the noise generation mechanisms in a jet. Such information can be vital to the design of future noise-reducing nozzle geometries. This project uses the simulation data generated by a large eddy simulation (LES) tool to investigate the creation and propagation of upstream moving sound waves in the potential core …

Numerical Solver For Multiphase Flows, Victor C B Sousa, Carlo Scalo

The Summer Undergraduate Research Fellowship (SURF) Symposium

The technological development of micro-scale electronic devices is bounded by the challenge of dissipating their heat output. Latent heat absorbed by a fluid during phase transition offers exceptional cooling capabilities while allowing for the design of compact heat exchangers. The understanding of heat transport dynamics in the context of multiphase flow physics is hampered by the limited access to detailed flow features offered by experimental measurements. Computational Fluid Dynamics (CFD) can overcome such difficulties by providing a complete description of the three-dimensional instantaneous flow field. Unfortunately, the majority of the numerical investigations in this field at Purdue are carried out …

Similarity Analysis Of A Swirling Counter-Flow, Jitesh Rane

Doctoral Dissertations and Master's Theses

Swirling counter-flows are used in numerous engineering applications, like combustion, heat exchangers, cyclonic separation and mixing, etc. These swirling counter-flows produce complex flow fields. It is important to study these types of flows in order to use them properly in many applications.

The present work provides insight into the flowfield inside a swirling counter-flow when the fluid is injected tangentially in a cylindrical container. A semi-analytical solution is developed by starting with the full Navier-Stokes equation and using a similarity analysis. A decaying swirl along the axis of the cylinder is assumed, which reduces the Navier-Stokes equations to first order …

Validation Of A Cfd Approach For Gas Turbine Internal Cooling Passage Heat Transfer Prediction, Daniel G. Wilde

Master's Theses

This report describes the development and application of a validated Computational Fluid Dynamics (CFD) modelling approach for internal cooling passages in rotating turbomachinery. A CFD Modelling approach and accompanying assumptions are tuned and validated against academically available experimental results for various serpentine passages. Criteria of the CFD modelling approach selected for investigation into advanced internal cooling flows include accuracy, robustness, industry familiarity, and computational cost.

Experimental data from NASA HOST (HOt Section Technology), Texas A&M, and University of Manchester tests are compared to RANS CFD results generated using Fluent v14.5 in order to benchmark a CFD modelling approach.

Capability of …

Computational Fluid Dynamics Applied To The Analysis Of Blood Flow Through Central Aortic To Pulmonary Artery Shunts, Carey Celestin Jr

LSU New Orleans Theses and Dissertations

This research utilizes CFD to analyze blood flow through pathways representative of central shunts, commonly used as part of the Fontan procedure to treat cyanotic heart disease. In the first part of this research, a parametric study of steady, Newtonian blood flow through parabolic pathways was performed to demonstrate the effect that flow pathway curvature has on wall shear stress distribution and flow energy losses. In the second part, blood flow through two shunts obtained via biplane angiograms is simulated. Pressure boundary conditions were obtained via catheterization. Results showed that wall shear stresses were of sufficient magnitude to initiate platelet …

Concurrent Engineering Through Parallelization Of The Design-Analysis Process, Eric Joseph Wardell

Theses and Dissertations

The disconnect between the way CAD and analysis applications handle model geometry has long been a hindrance to engineering design. Current industry practices often utilize outdated forms of geometry transfer between these different engineering software applications such as neutral file formats and direct translations. Not only to these current practices slow the engineering design process but they also hinder the integration of design and analysis programs.This thesis proposes a new, multi-user, integrated design-analysis architecture which allows auxiliary functions such as analysis and computer-aided manufacturing to be better connected with the computer-aided design. It is hypothesized that this new architecture will …

An Investigation Of Off-Design Operation In High Suction Performance Inducers, Ryan Collins Cluff

Theses and Dissertations

Three-dimensional two-phase unsteady CFD simulations were run on three and four-blade inducers for the purpose of analyzing differences in cavitation stability at design and off-design flow rates. At design flow rates, there were very small differences between the breakdown curves for the three and four-bladed inducers. However, at lower cavitation numbers, the three-bladed inducer exhibited up to three times the rotor forces than the four-bladed inducer. When moving to off-design flow rates, both inducers experienced multiple modes of cavitation instabilities including rotating cavitation, alternate-blade cavitation, and cavitation surge. The four-bladed inducer began experiencing the formation of these modes of instability …

Experimental Validation Data For Cfd Of Steady And Transient Mixed Convection On A Vertical Flat Plate, Blake W. Lance

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

In this computer age, simulations are becoming common in science and engineering. One category of simulation, Computational Fluid Dynamics (CFD), begins with physical equations but adds approximations and calibrations in order to complete solutions. Translating these equations into computer languages may cause unintended errors. If simulation results are to be used for decision making, their accuracy needs to be assessed. This accuracy assessment is the theory behind the field of Verification & Validation.

Verification involves confirming the translation of physical equations to computer language was per- formed correctly. It also features methods to detect many types of code errors. Validation …

Development Of A Rapid Compression Controlled-Expansion Machine For Chemical Ignition Studies, John Neuman

Master's Theses (2009 -)

The ability to accurately model fuel combustion processes is essential to the development of transportation, power generation, and manufacturing technology. Models describing the kinetics of chemical oxidation are readily available and highly refined for a wide range of test fuels. However, these models still suffer from high levels of uncertainty under engine-relevant conditions, largely due to a lack of consistency between published validation data. An experimental testing apparatus, known as the Rapid Compression Controlled-Expansion Machine (RCCEM) has been designed and fabricated to conduct chemical kinetic studies. The RCCEM features a pneumatically-driven, custom-designed cam, which governs the volumetric compression and expansion …

Experimental Validation Data For Cfd Of Transient Convection From Forced To Natural With Flow Reversal On A Vertical Flat Plate, Blake W. Lance, Barton L. Smith

Engineering Datasets

Transient convection was investigated experimentally for the purpose of providing Computational Fluid Dynamics (CFD) validation data. A specialized facility for validation experiments called the Rotatable Buoyancy Tunnel was used to acquire thermal and velocity measurements of flow over a smooth, vertical heated plate. The initial condition was forced convection downward with subsequent transition to mixed convection, ending with natural convection upward after a flow reversal. Data acquisition through the transient was repeated for ensemble-averaged results. With simple flow geometry, validation data were acquired at the benchmark level. All boundary conditions (BCs) were measured and their uncertainties quantified. Temperature profiles on …

Analytical And Numerical Validation Of Nozzle Spray Measurement Data Obtained From A Newly Developed Production System, Iddrisu Seidu

ETD Archive

A newly developed production test stand for measuring the spray angle of a pressure swirl atomizer was constructed and used to measure a product line of these pressure swirl atomizers -- the macrospray atomizer. This new test stand, utilizing constant temperature hot wire anemometers, captures the spray angle data based on the voltage drop the hot wire probes see as they traverse the spray cone of the atomizer and as fluid droplets impinge upon the wire. Datasets acquired from the experiments are compared and correlated with computational fluid dynamics (CFD) simulation data. In addition, angles obtained from another type of …

High Temperature Flow Solver For Aerothermodynamics Problems, Huaibao Zhang

Theses and Dissertations--Mechanical and Aerospace Engineering

A weakly ionized hypersonic flow solver for the simulation of reentry flow is firstly developed at the University of Kentucky. This code is the fluid dynamics module of known as Kentucky Aerothermodynamics and Thermal Response System (KATS). The solver uses a second-order finite volume approach to solve the laminar Navier– Stokes equations, species mass conservation and energy balance equations for flow in chemical and thermal non-equilibrium state, and a fully implicit first-order backward Euler method for the time integration. The hypersonic flow solver is then extended to account for very low Mach number flow using the preconditioning and switch of …

Application Of Computational Fluid Dynamics To Near-Wellbore Modeling Of A Gas Well, Oscar Mauricio Molina

LSU Master's Theses

Well completion plays a key role in the economically viable production of hydrocarbons from a reservoir. Therefore, it is of high importance for the production engineer to have as many tools available that aid in the successful design of a proper completion scheme, depending on the type of formation rock, reservoir fluid properties and forecasting of production rates. Because well completion jobs are expensive, most of the completed wells are usually expected to produce as much hydrocarbon and as fast as possible, in order to shorten the time of return of the investment. This research study focused on the evaluation …

Bio-Inspired Optimal Fin Shape And Angle For Maximum Surfboard Stability, Megan S. Macneill

Dissertations, Master's Theses and Master's Reports - Open

Wave surfing is a multi-billion dollar industry involving both maneuverability and speed, yet little research has been done regarding optimal fins shape for these competing qualities. The purpose of this master's thesis was to focus on a single fin setup in order to identify a bio-inspired fin shape that maximized lateral stability while minimizing drag forces, in order to increase surfing maneuverability.

The computational fluid dynamic models NX and laboratory experiments performed in a water channel, with lift and drag being directly measured, were used to compare nine fins based on dorsal fins of real fish. To properly compare, fluid …

Specialized Inter-Particle Interaction Lbm For Patterned Superhydrophobic Surfaces, Amal Saeed Yagub

Wayne State University Dissertations

SPECIALIZED INTER-PARTICLE INTERACTION LBM FOR PATTERNED SUPERHYDROPHOBIC SURFACES

by

AMAL S. YAGUB

ABSTRACT:

Superhydrophobic surface characteristics are important in many industrial applications, ranging from the textile to the military. It was observed that surfaces fabricated with nano/micro roughness can manipulate the droplet contact angle, thus providing an opportunity to control the droplet wetting characteristics. The Shan and Chen (SC) lattice Boltzmann model (LBM) is a good numerical tool, which holds strong potentials to qualify for simulating droplets wettability. This is due to its realistic nature of droplet contact angle (CA) prediction on flat smooth surfaces. But SC-LBM was not able …

Design Of A High Intensity Turbulent Combustion System, Mohammad Arif Hossain

Open Access Theses & Dissertations

In order to design next generation gas turbine combustor and rocket engines, a systematic study of flame structure at high intensity turbulent flow is necessary. The fundamental study of turbulent premixed combustion has been a major research concern for decades. The work is focused on the design and development of a high intensity turbulent combustion system which can be operated at compressible (0.3 < M < 0.5), preheated (T0=500K) and premixed conditions in order to investigate the 'Thickened Flame' regime. An air-methane mixture has been used as the fuel for this study. An optically accessible backward-facing step stabilized combustor has been designed for a maximum operating pressure of 6 bar. A grid has been introduced with different blockage ratios (BR = 54%, 61% & 67%) in order to generate turbulence inside the combustor for the experiment. Optical access is provided via quartz windows on three sides of the combustion chamber. Finite Element Analysis (FEA) is done in order to verify the structural integrity of the combustor at rated conditions. In order to increase the inlet temperature of the air, a heating section was designed to use commercially available in-line heaters. Separate cooling subsystems have been designed for chamber cooling and exhaust cooling. The LabVIEW software interface has been selected as the control mechanism for the experimental setup. A 10 kHz Time Resolved Particle Image Velocimetry (TR-PIV) system and a 3 kHz Planer Laser Induced Fluorescence (PLIF) system have been integrated with the system in order to diagnose the flow field and the flame respectively. The primary understanding of the flow field inside the combustor was achieved through the use of Detached Eddy Simulation (DES) by using commercially available software package ANSYS FLUENT. Preliminary validation is done by 10 kHz TR-PIV technique. Both qualitative and quantitative analysis have been done for CFD and experiment. Major flow parameters such as average velocity, fluctuation of velocity, kinetic energy, and turbulent intensity have been calculated for two distinct Reynolds number (Re = 815 & 3500). PIV results are compared with CFD results which show significant agreement with each other.

Modeling And Analysis Of Reactivity Controlled Compression Ignition (Rcci) Combustion, Mohammadreza Nazemi

Dissertations, Master's Theses and Master's Reports - Open

Homogeneous Charge Compression Ignition (HCCI) and Premixed Charge Compression Ignition (PCCI) combustion strategies are promising methods for achieving low engine-out NOx and soot emissions as well as high indicated efficiency. However, these combustion strategies have difficulties with controlling the rate of heat release and lack of an adequate combustion phasing control mechanism. A dual-fuel Reactivity Controlled Compression Ignition (RCCI) combustion strategy will address these issues due to the existence of precise means for controlling the heat release rate and combustion phasing. In the RCCI strategy two fuels with different reactivity (auto-ignition characteristics, e.g., gasoline and diesel) are blended inside the …

Ambit Of Multiphase Cfd In Modelling Transport Processes Related To Oil Spill Scenario And Microfluidics, Abhijit Rao

LSU Doctoral Dissertations

During the ‘Deepwater Horizon’ accident in the deep sea in 2010, about 4.9 million barrels of oil was released into the Gulf of Mexico, making the spill one of the worst ocean spills in recent times. To mitigate the ill effects of the event on the environment, subsea injection of dispersants was carried out. Dispersant addition lowers the interfacial tension at oil/water interface and presence of local turbulence enhances the droplet disintegration process. The oil droplets contain a plethora of hydrocarbons which are soluble in water. In deep spill scenarios, droplets spend large amounts of time in water column; hence, …

Applications Of Cfd Simulations On Fractal Fluid Distributor, Gongqiang He

LSU Master's Theses

Since its emergence in 1970s, process intensification has been attracting extensive research interests from both academic and industrial societies over the years. One good example of process intensification in chemical industry is the optimization of flow distributors. In many chemical processes, the uniformity of flow distributions plays the key role in determining the overall efficiency. Conventional distributors rely on high pressure drop to achieve acceptable flow distribution. With scaling symmetry from fractal, fractal distributors can handle fluid distribution much better than conventional distributors. With the rapid development of computation power and numerical simulation algorithms, Computer Fluid Dynamics (CFD) provides us …

Evaluation Of The Mass Transfer Effect Of The Stalk Contraction–Relaxation Cycle Of Vorticella Convallaria, Jiazhong Zhou

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Vorticella convallaria is a genus of protozoa living in fresh water. It has a bell-shaped zooid equipped with adoral ciliary bands and a contractile stalk tethering the zooid to a substrate. Vorticella is regarded as a biological spring because its contractile stalk can pull the zooid towards the substrate at a remarkably high speed and then relaxes to its extended state much more slowly. However, reasons for Vorticella’s stalk contraction are still unknown. It is presumed that the flow field induced by the contraction-relaxation cycle of Vorticella would augment mass transfer effect near the substrate. We investigated this hypothesis …

Numerical Simulation Of The Heat Leakage At The Gasket Region Of Domestic Refrigerators, Feng Gao

All Theses

Computational Fluid Dynamics (CFD) simulations are performed to investigate the heat loss at the gasket of a standard over/under domestic refrigerator. The study numerically simulates a unique experimental test cell with only the gasket region exposed to the ambient environment and other parts protected by insulation (see picture below). The test cell is cubic with an interior cavity having dimensions 2' x 2' x 2' within which a heating element is placed to create a specified temperature difference. A matching set of door and side panels exposes a 2' width of the gasket region to heat transfer with the surroundings. …

A Cfd Investigation Of The Hydrodynamic Characteristics Of Fluid Flow Through An Impeller And Multi-Objective Design Optimization Of A Centrifugal Pump, Mohammed Khammat Sagban

Doctoral Dissertations and Master's Theses

In this thesis, the first part is conducting an investigation of the hydrodynamic characteristics (pressure and velocity) of fluid flow (water) through an impeller of a centrifugal pump. To illustrate a one-dimensional model is used to identify an impeller of a GDM 10 x 12 HD centrifugal pump using Vista CPD design and BladeGen tool. A three-dimensional model is then built with a commercial software package ANSYS Blade Modeler. The structured mesh of the impeller blade is obtained by using TurboGrid system. The volute of the centrifugal pump is built in ANSYS geometry, and an unstructured mesh is accomplished by …

Computational Fluid Dynamics Analysis Of Freeze Drying Process And Equipment, Nikhil P. Varma

Open Access Theses

Freeze drying is an important, but expensive, inefficient and time consuming process in the pharmaceutical, chemical and food processing industries. Computational techniques could be a very effective tool in predictive design and analysis of both freeze drying process and equipment. This work is an attempt at using Computational Fluid Dynamics(CFD) and numerical simulations as a tool for freeze drying process and equipment design.

Pressure control is critical in freeze dryers, keeping in view the product stability. In industrial freeze dryers, loss of pressure control can lead to loss of an entire batch. Pressure variation within the chamber could also lead …

Extended Formation Flight At Transonic Speeds, Andrew Ning, Ilan Kroo, Michael Aftosmis, Marian Nemec, James Kless

Faculty Publications

Aircraft flown in formation can realize significant reductions in induced drag by flying in regions of wake upwash. However, most transports fly at transonic speeds where the impact of compressibility on formation flight is not well understood. This study utilizes an Euler solver to analyze the inviscid aerodynamic forces and moments of transonic wing/body configurations flying in a two-aircraft formation. Formations with large streamwise separation distances (10-50 wingspans) are considered.

This work indicates that compressibility-related drag penalties in formation flight may be eliminated by slowing 2-3% below the nominal out-of-formation cruise Mach number (either at fixed lift coefficient or fixed …

Evaluation Of The Performance Of Various Turbulence Models For Accurate Numerical Simulation Of A 2d Slot Nozzle Ejector, Colin Graham

McKelvey School of Engineering Graduate Student Theses & Dissertations

With the development over the last several decades, accurate Computational Fluid Dynamics (CFD) modeling has now become an essential part in the analysis and design of various industrial products where the fluid flow plays an important role. The goal of this thesis is to apply the CFD technology to the analysis of a 2D slot nozzle ejector which has application in Short Take-off and Landing (STOL) aircraft and other future aerospace vehicles. In the nozzle-ejector configuration, the high speed air flow from the nozzle entrains the ambient air into a mixing chamber (ejector) as a means to create additional thrust …