Engineering Commons^™

Cfd/Fea Of A Steam Methane Reforming Tube, Matthew Wegener

Research Opportunities for Engineering Undergraduates (ROEU) Program 2017-18

Steam methane reforming is the primary method by which hydrogen is produced; increased efficiency in hydrogen production could enable hydrogen’s usage as an alternative fuel. The objectives of this project are to construct a robust CFD/FEA model of a steam methane reforming tube, and to perform CFD/FEA analysis in both steady and transient operational states, comparing thermal stresses/strains in the tube wall in the two states and relating tube stresses/strains to properties of the process controller.

Coupling Computational Fluid Dynamics Analysis And Optimization Techniques For Scramjet Engine Design, Nathan T. Mcgillivray

Browse all Theses and Dissertations

Various aspects of hypersonic vehicles are being rapidly explored for improved functionality. One of the main areas of consideration is the fueling of a Supersonic Combusting Ramjet (scramjet) engine. Using Computational Fluid Dynamics (CFD), computer simulations can be performed to analyze the flow physics of a scramjet. In this research, an optimization code, Dakota, is integrated with the CFD to optimize a set of parameters to maximum thrust. In this study, the fuel injection and combustion is replaced with heat sources. This simplification greatly reduces the computational requirements. Additionally, the 3D geometry is reduced to an axisymmetric 2D geometry because …

An Experimental And Computational Study Of Fuel Spray Interaction: Fundamentals And Engine Applications, Le Zhao

Dissertations, Master's Theses and Master's Reports

An efficient spray injection results in better vaporization and air-fuel mixing, leading to combustion stability and reduction of emissions in the internal combustion (IC) engines. The impingement of liquid fuels on chamber wall or piston surface in IC engines is a common phenomenon and fuel film formed in the spray-piston or cylinder wall impingement plays a critical role in engine performance and emissions. Therefore, the study of the spray impingement on the chamber wall or position surface is necessary.

To understand the spray-wall interaction, a single droplet impingement on a solid surface with different conditions was first examined. The droplet-wall …

Hydrodynamics Related Performance Evaluation Of Upflow Moving Bed Hydrotreater Reactor (Mbr) Using Developed Experimental Methods And Cfd Simulation, Vineet Alexander

Doctoral Dissertations

"Upflow Moving Bed Hydrotreater (MBR) reactor is used for hydrotreating resid crude oil. It is a two-phase upflow reactor having a catalyst bed with conical bottom, and plena. At industrial conditions the reactor is not performing at its best and encountering issues such as hot spots, catalyst agglomeration inside the catalyst bed leading to frequent shutdown of the reactor. The root cause of these problems are linked to the improper hydrodynamics inside the catalyst bed. To investigate this, the industrial scale MBR is scaled down to a pilot scale and indicative and key hydrodynamic parameters are investigated using developed experimental …

Multiphase Flow Modeling For Design And Optimization Of A Novel Down-Flow Bubble Column, Mutharasu Lalitha Chockalingam

LSU Doctoral Dissertations

The application of the Euler-Euler framework based Computational Fluid Dynamics (CFD) models for simulating the two-phase gas-liquid bubbly flow in down-flow bubble columns is discussed in detail. Emphasis is given towards the modelling and design optimization of a novel down-flow bubble column. The design features of this novel down-flow bubble column and its advantages over a conventional Plunging Jet down-flow bubble column are discussed briefly. Then, some of the present challenges in simulating a conventional Plunging Jet down-flow bubble column in the Euler-Euler framework is highlighted, and a sigmoid function based drag modification function is implemented to overcome those challenges. …

Multiphase Flow Modeling And Analysis Of Phased Filling Process For Pulsed Detonation Engine, Nirmal Kumar Umapathy

Mechanical and Aerospace Engineering Theses - Archive

Filling of reactants into a pulsed detonation engine (PDE) should be carried out quickly because any lengthening of the fill time will lead to an increased cycle time. The fill process and, the purge process constitutes a large proportion of time in a cycle. The purpose of this research was to improve the time of fill by implementing various injection geometries in two injection schemes with five different premixed stoichiometric fuel-air mixture injected at wide range of velocity. The different configurations examined were end wall injection, side wall injection with ports angled and normal to the flow direction and staggered …

A Comparison Of Mean Age Theory And Residence Time Distributions In Mixed Systems., Nolan Theaker

Electronic Theses and Dissertations

A comparison between mean age theory and conventional residence time distributions over a range of quantified mixing levels was conducted using computational fluid dynamics (CFD). The system was a stirred tubular reactor. The model was validated by comparing computationally derived RTD curves with experimentally obtained RTD curves, with quantified differences less than 3%. Mixing was quantified using the Tanks-in-Series model. Mixing levels were set by varying flow rate and impeller rpm. Mean age distributions at the outlet, where experimental RTD’s were measured, were very narrow for all levels of mixing studied. RTD’s showed expected characteristics; a wider distribution and long …

The Effects Of Exhaust Vent Location On Thermal Comfort Inside The Residential Buildings Equipped With An Evaporative Cooling System, Armin Saraei

UNLV Theses, Dissertations, Professional Papers, and Capstones

Inlet and outlet conditions, Including size and location, have significant effects on the air distribution, temperature, humidity and thermal comfort in the buildings. In the current study, various strategies are presented for exhaust air vents and the effects of inlet and outlet vents locations are evaluated on providing thermal comfort in the residential and industrial buildings. To provide thermal comfort, three key factors need to be investigated based on ASHRAE standard 55- 2013 as follows: Comfort Zone, Thermal Sensation and Draft Rate. Flow distribution is studied as well in order to investigate the strategies, which make more vorticity in the …

Numerical Characterization Of The Flow Field And Heat Transfer Inside The Receiver Of A Parabolic Trough Solar Collector Carrying Supercritical Co2, Samad Gharehdaghimollahajloo

UNLV Theses, Dissertations, Professional Papers, and Capstones

The aim of this research is to provide a detailed numerical analysis of flow field and heat transfer inside the heat collecting element of a parabolic trough collector. The parabolic trough collector is used as the boiler in a direct Super Critical Carbon Dioxide (S-CO2) Brayton cycle.

A single collector is modeled and analyzed with different inlet conditions. The working fluid is supercritical since its pressure is increased to above critical pressure in the compressor while its temperature reaches 300 °C after passing through the recuperators and before entering the solar field. For the first time, this research considers both …

A High Quality, Eulerian 3d Fluid Solver In C++, Lejon Anthony Mcgowan

Computer Science and Software Engineering

Fluids are a part of everyday life, yet are one of the hardest elements to properly render in computer graphics. Water is the most obvious entity when thinking of what a fluid simulation can achieve (and it is indeed the focus of this project), but many other aspects of nature, like fog, clouds, and particle effects. Real-time graphics like video games employ many heuristics to approximate these effects, but large-scale renderers aim to simulate these effects as closely as possible.

In this project, I wish to achieve effects of the latter nature. Using the Eulerian technique of discrete grids, I …

Aerosol Transport By Coughing In A Depressurized And Air-Conditioned Chamber, Bo Zhang

Dissertations

Expiratory droplets from human coughing in an air-conditioned environment have always been considered to be potential carriers of pathogens, responsible for respiratory disease transmission. The air movement/circulation and ambient conditions such as pressure and temperature are all key factors of aerosol transport. To study the transmission of disease by human coughing in a depressurized air-conditioned chamber, there are many technical challenges, including the following: 1) the study of simulating human coughing; 2) the collection of aerosol generated by coughing; 3) the CFD simulation of coughing-induced aerosol transport in an air-conditioned chamber; 4) the validation of such a CFD simulation by …

Dpm Dispersion Inside A Single Straight Entry Using Dynamic Mesh Model, Yi Zheng, Ying Li, Magesh Thiruvengadam, Hai Lan, Jerry C. Tien

Mining Engineering Faculty Research & Creative Works

Three-dimensional simulations of diesel particulate matter (DPM) distribution inside a single straight entry for the Load-Haul-Dump loader (LHD)-truck loading and truck hauling operations were conducted by using ANSYS FLUENT computational fluid dynamics software. The loading operation was performed for a fixed period of 3 min. The dynamic mesh technique in FLUENT was used to study the impact of truck motion on DPM distribution. The resultant DPM distributions are presented for the cases when the truck was driving upstream and downstream of the loading face. Interesting phenomena were revealed in the study including the piston effect, layering of DPM in the …

Applications Of Cfd Simulations On Chemical Processing Equipment Designs, Gongqiang He

LSU Doctoral Dissertations

The objective of this work is to achieve process intensification by seeking optimal equipment design with CFD investigations. In this work, two projects on chemical equipment design have been discussed.

The first project is on design and optimization of fractal distributor in a novel ion-exchanger. Flow distributors are adopted extensively by chemical industry to distribute an incoming process stream uniformly to the downstream equipment. Currently, the performance of chemical equipment installed with conventional distributor is severely undermined due to poor flow distribution. For conventional distributors such as spray nozzle distributors, their design concept is based on maintaining very high pressure …

Design And Validation Of Pressure Based Flow Rate Soft Sensor For Freeze-Drying, Pasita Pibulchinda, Tong Zhu, Vaibhav Kshirsagar, Alina A. Alexeenko

The Summer Undergraduate Research Fellowship (SURF) Symposium

Lyophilization or freeze drying is a process of removing water by sublimation. It is commonly used to extend the shelf life of drugs in the pharmaceutical industry. Because the process is costly and time consuming, precise and efficient pressure, temperature control and drying time estimation are required. It is the goal of freeze-drying to run at maximum capacity while staying within the safe zone by carefully controlling the sublimation rate. Currently, real time estimation of sublimation rate is still challenging. The technique available called Tunable diode laser absorption spectroscopy (TDLAS) is invasive, and requires major modifications. The current study focuses …

Cfd Performance Of Turbulence Models For Flow From Supersonic Nozzle Exhausts, Han Ju Lee

McKelvey School of Engineering Graduate Student Theses & Dissertations

The goal of this thesis is to compare the performance of several eddy-viscosity turbulence models for computing supersonic nozzle exhaust flows. These flows are of relevance in the development of future supersonic transport airplane. Flow simulations of exhaust flows from three supersonic nozzles are computed using ANSYS Fluent. Simulation results are compared to experimental data to assess the performance of various one- and two-equation turbulence models for accurately predicting the supersonic plume flow. One particular turbulence model of interest is the Wray-Agarwal (WA) turbulence model. This is a neat model which has demonstrated promising results mimicking the strength of two …

Cfd Simulations Of Chemical Looping Combustion In A Packed Bed And A Bubbling Bed Fuel Reactor, Guanglei Ma

McKelvey School of Engineering Graduate Student Theses & Dissertations

Chemical-looping combustion (CLC) is a next generation combustion technology that has shown great promise in addressing the need for high-efficiency low-cost carbon capture from fossil fueled power plants to address the rising carbon emissions. Although there have been a number of experimental studies on CLC in recent years, CFD simulations have been limited in the literature on CLC. The development and confidence in high-fidelity simulations of the CLC process is a necessary step towards facilitating the transition from laboratory-scale experiments to deployment of this technology on an industrial scale. In this research, first the CFD simulations of a CLC packed …

Numerical Drag Prediction Of Nasa Common Research Models Using Different Turbulence Models, Pan Du

McKelvey School of Engineering Graduate Student Theses & Dissertations

The goal of this research is to perform 3D turbulence flow simulations to predict the drag of Wing-body-tail (WBT) and Wing-body-nacelle-Pylon (WBNP) aircraft configurations from NASA Common Research Models. These configurations are also part of the 4th and 6th AIAA Drag Prediction Workshops in which CFD modelers have participated worldwide. The computations are performed using CFD solver ANSYS FLUENT. The compressible Reynolds-Averaged Navier-Stokes (RANS) equations are solved using two turbulence models – the Spalart-Allmaras (SA) and SST k-ω. Drag polar and drag rise curves are obtained by performing computations at different angles of attack at a constant Mach number. Pressure …

Numerical Study Of The Aerodynamics Of Dlr-F6 Wing-Body In Unbounded Flow Field And In Ground Effect, Ning Deng

McKelvey School of Engineering Graduate Student Theses & Dissertations

The main focus of this thesis is on the simulation of flow past a three-dimensional wing-body configuration (DLR-F6) in ground effect; a complex 3D wing-body configuration in ground effect has never been analyzed in the aerodynamics literature to date. For the purpose of validation of the simulation approach, computations are performed for the DLR-F6 wing-body in unbounded flow and are compared with the experimental data. The commercial CFD solver ANSYS FLUENT is employed for computations. Compressible Reynolds-Averaged Navier-Stokes (RANS) equations in conjunction with Spalart-Allmaras (SA) and - Shear Stress Transport (SST) turbulence models are solved. The validated code is employed …

Performance Investigation Of Three Combined Airfoils Bladed Small Scale Horizontal Axis Wind Turbine By Bem And Cfd Analysis, Md Mehedi Hasan, Adel El-Shahat, Mosfequr Rahman

Electrical & Computer Engineering: Faculty Publications

The present work is based on the comparative study between “Blade-Element- Momentum” (BEM) analysis and “Computational-Fluid-Dynamics” (CFD) analysis of small-scale horizontal axis wind turbine blade. In this study, the pitch is considered as fixed and rotor speed is variable. Firstly, the aerodynamic characteristics of three different specialized airfoils were analyzed to get optimum design parameters of wind turbine blade. Then BEM was performed with the application of the open source wind turbine design and performance computation software Q-Blade v0.6. After that, CFD simulation was done by Ansys CFX software. Here, k-ω “Shear-Stress-Transport” (SST) model was conducted for three-dimensional visualization of …

Evaluation Of Flux Correction On Three-Dimensional Strand Grids With An Overset Cartesian Grid, Dalon G. Work

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Simulations of fluid flows over complex geometries are typically solved using a solution technique known as the overset meshing method. The geometry is meshed using grid types appropriate to the local geometry in a patchwork fashion, rather than meshing the entire geometry with one type of mesh. The strand-Cartesian approach is a simplification of this process. While high-order accurate solvers on Cartesian grids are simple to implement, strand grids are usually restricted to second-order accuracy, resulting in poor quality solutions. Flux correction is a high-order accurate solution method, specifically designed for use on strand grids. The flux correction method on …

Effect Of Design Parameters On Thermal Performance Of A Vane Type Disc Brake Rotor, Yogesh Satish Dalal

Masters Theses

The ever-increasing need of effective transportation puts automobile manufacturers in a situation of continuous improvement and innovate the safety systems. The brake system of an automobile has always been considered as one of the most critical active safety systems. Thermal characteristics of the brake are an important aspect to consider for brake disc durability and performance. The convective cooling of a brake disc is an important factor since design changes in the brake rotor can significantly improve cooling characteristics. The focus of this research is to study and optimize the disc brake rotor for a given heat dissipation rate and …

Development Of An Analysis And Design Optimization Framework For Marine Propellers, Ashish C. Tamhane

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, a framework for the analysis and design optimization of ship propellers is developed. This framework can be utilized as an efficient synthesis tool in order to determine the main geometric characteristics of the propeller but also to provide the designer with the capability to optimize the shape of the blade sections based on their specific criteria.

A hybrid lifting-line method with lifting-surface corrections to account for the three-dimensional flow effects has been developed. The prediction of the correction factors is achieved using Artificial Neural Networks and Support Vector Regression. This approach results in increased approximation accuracy compared …

Formula Sae Intake System, Esa Mahmood, Arman Sarwar, Michael R. Smith

Capstone Design Expo Posters

The Formula SAE Intake System is intended to optimize the airflow into a restricted 600cc engine. The intake system is designed, fabricated, and installed in accordance with the FSAE rule book with a focus on maximizing the vehicle’s acceleration. It is directly responsible for determining the drivability of the car and how much horsepower the flow restricted engine produces.

Design of the intake was conceptualized based on researching a number of factors including venturi diffusion angles, plenum volumes, and runner lengths. Initial tests were performed utilizing computational fluid dynamics for a total of 367 flow simulations and 261 running hours …

Computational Modeling Of A Williams Cross Flow Turbine, Sajjan Pokhrel

Browse all Theses and Dissertations

Hydropower is not only the most used renewable energy source in the United States, but in the world. While it is well known that large hydropower facilities, like the Hoover Dam, provide large amounts of electrical power, there is also a tremendous opportunity for hydroelectric power generation from small scale facilities that has largely been overlooked. The work being presented here studies a new cross flow turbine called the Williams Cross Flow Turbine (WCFT), which was designed to extract electric energy from low head, run-of-the-river, small hydropower sites. To spur the implementation of the WCFT in small hydropower applications, and …

Assessment Of Varying Model Representations In Cfd Simulations, Caitlin R. Gerdes

Electronic Theses and Dissertations

This thesis investigates the effects of varying model refinement and representation of computational fluid dynamics (CFD) simulations in two case studies. Product and process realization in engineering design requires substantial resources (time and money) in order to test novel designs for effectiveness. In recent decades, engineering has been relying more heavily on simulation-based analysis in the design process with computer models to help reduce the demands for real-life testing. The first case study analyzed in this thesis is a photobioreactor, which is used to grow microalgae for biofuel and require a balance of nutrients, light, and mixing for growth. The …

A Physics-Based Approach To Modeling Wildland Fire Spread Through Porous Fuel Beds, Tingting Tang

Theses and Dissertations--Mechanical and Aerospace Engineering

Wildfires are becoming increasingly erratic nowadays at least in part because of climate change. CFD (computational fluid dynamics)-based models with the potential of simulating extreme behaviors are gaining increasing attention as a means to predict such behavior in order to aid firefighting efforts. This dissertation describes a wildfire model based on the current understanding of wildfire physics. The model includes physics of turbulence, inhomogeneous porous fuel beds, heat release, ignition, and firebrands. A discrete dynamical system for flow in porous media is derived and incorporated into the subgrid-scale model for synthetic-velocity large-eddy simulation (LES), and a general porosity-permeability model is …

Development Of An Evaporation Sub-Model And Simulation Of Multiple Droplet Impingement In Volume Of Fluid Method, Sathya Prasad Potham

Dissertations, Master's Theses and Master's Reports

Droplet collision and impingement on a substrate are widely observed phenomenon in many applications like spray injection of Internal Combustion Engines. Existing Lagrangian models do not provide a comprehensive picture of the outcome of these events and may involve model constants requiring experimental data for validation. Physics based models like Volume of Fluid (VOF) method involve no parametric tuning and are more accurate. The aim of this thesis is to extend the basic VOF method with an evaporation sub-model including an additional vapor phase and implement this model in an open source Computational Fluid Dynamics (CFD) software, OpenFOAM. The new …

Last Two Surface Range Detector For Direct Detection Multisurface Flash Lidar In 90nm Cmos Technology, Douglas Preston

Browse all Theses and Dissertations

This thesis explores a novel detection architecture for use in a Direct-Detect Flash LIDAR system. The proposed architecture implements detection of the last two surfaces within single pixels of a target scene. The novel, focal plane integrated detector design allows for detection of objects behind sparse and/or partially reflective covering such as forest canopy. The proposed detector would be duplicated and manufactured on-chip behind each avalanche photodiode within a focal plane array. Analog outputs are used to minimize interference from digital components on the analog input signal. The proposed architecture is a low-footprint solution which requires low computational post-processing. Additionally, …

Design And Performance Analysis Of Small Scale Horizontal Axis Wind Turbine For Nano Grid Application, Md Mehedi Hasan

College of Graduate Studies: Theses & Dissertations

Wind energy, being easily accessible, environmentally friendly, and being cost effective, has become one of the world’s popular growing renewable energy sources of electricity generation. To spread this technology to mankind it is necessary to develop turbines in this way that people can use it individually and comfortably. This kind of thinking accelerates the advancement of integration of wind turbine with Nano grid concept. Although significant progress has been achieved in the wind technology, there is still scope to reduce the cost and improve the performance of small-scale wind turbines. Moreover, low wind velocity should also need to be utilized …

Experimental And Numerical Study Of Dysphagia, Yash G. Potdar

Masters Theses

Dysphagia, meaning difficulty in swallowing, is a symptom of disease that occurs in young children and elderly people. It occurs particularly due to two reasons, weak neural network and/or deformities in oral section/s. The Helen DeVos Children’s Hospital’s Intensive Feeding Program takes care of children suffering from Dysphagia. In order to make the swallowing process easier and in some cases safer, thickener is added to the liquids. Depending on the requirement of thickness, the amount of thickener is varied. Although the directions to prepare the mixtures are given by the thickener product company, the required thickness is not achieved when …