Engineering Commons^™

Photocatalytic Reactor Using Tio2 Thin Film On Quartz Tubes, Ram Mahipal Kouda

Graduate Theses and Dissertations

Photocatalysis process, as an environmental application is an advanced oxidation process with tremendous potential in the near future. Previously many researchers, have conducted photocatalysis in different reactor configuration using TiO2 slurry and thin film, using a UV light source, the constraints for these reactors are the need for the removal of TiO2 particles at the outlet stream in a slurry reactor and poor environment for the efficient use of TiO2 film using UV light, as the UV light penetration depth in water is about an inch.

Taking all this into consideration, we propose a design for reactor with efficient contact …

Design Of An Rf Cmos Power Amplifier For Wireless Sensor Networks, Hua Pan

Graduate Theses and Dissertations

The Power Amplifier (PA) is the last Radio Frequency (RF) building block in a transmitter, directly driving an antenna. The low power RF input signal of the PA is amplified to a significant power RF output signal by converting DC power into RF power. Since the PA consumes a majority of the power, efficiency plays one of the most important roles in a PA design. Designing an efficient, fully integrated RF PA that can operate at low supply voltage (1.2V), low power, and low RF frequency (433MHz) is a major challenge. The class E Power Amplifier, which is one type …

Implementation Of Orthogonal Frequency Division Multiplexing With Fpga, Qi Hao Yang

Graduate Theses and Dissertations

In recent years, there have been dramatic shifts in cellular and telecommunication industries. As smartphones are dominating on the cellphone market, more and more people use these mobile devices to access internet either through third generation network or IEEE802.11 wireless local area network. Orthogonal frequency division multiplexing (OFDM) has been widely used in IEEE802.11 wireless local area network and fourth generation network. This paper will focus on the design and implementation of an Orthogonal Frequency Division Multiplexing system on field-programmable gate array (FPGA). The major components of an OFDM system include a modulator, an N-input inverse Fast Fourier Transform (IFFT), …

Use Of Ultra High Vacuum Plasma Enhanced Chemical Vapor Deposition For Graphene Fabrication, Shannen Adcock

Graduate Theses and Dissertations

Graphene, what some are terming the "new silicon", has the possibility of revolutionizing technology through nanoscale design processes. Fabrication of graphene for device processing is limited largely by the temperatures used in conventional deposition. High temperatures are detrimental to device design where many different materials may be present. For this reason, graphene synthesis at low temperatures using plasma-enhanced chemical vapor deposition is the subject of much research. In this thesis, a tool for ultra-high vacuum plasma-enhanced chemical vapor deposition (UHV-PECVD) and accompanying subsystems, such as control systems and alarms, are designed and implemented to be used in future graphene growths. …

High Frequency Characterization Of Carbon Nanotube Networks For Device Applications, Emmanuel Decrossas

Graduate Theses and Dissertations

This work includes the microwave characterization of carbon nanotubes (CNTs) to design new CNTs-based high frequency components. A novel developed method to extract the electrical properties over a broad microwave frequency band from 10 MHz to 50 GHz of carbon nanotubes (CNTs) in a powder form is performed. The measured scattering parameters (S-parameters) with a performance network analyzer are compared to the simulated one obtained from an in-house computed mode matching technique (MMT). An optimized first order gradient method iteratively changes the unknown complex permittivity parameters to map the simulated S-parameters with the measured one until convergence criteria are satisfied. …

Ultra-Low Power And Radiation Hardened Asynchronous Circuit Design, Liang Zhou

Graduate Theses and Dissertations

This dissertation proposes an ultra-low power design methodology called bit-wise MTNCL for bit-wise pipelined asynchronous circuits, which combines multi-threshold CMOS (MTCMOS) with bit-wise pipelined NULL Convention Logic (NCL) systems. It provides the leakage power advantages of an all high-Vt implementation with a reasonable speed penalty compared to the all low-Vt implementation, and has negligible area overhead. It was enhanced to handle indeterminate standby states. The original MTNCL concept was enhanced significantly by sleeping Registers and Completion Logic as well as Combinational circuits to reduce area, leakage power, and energy per operation.

This dissertation also develops an architecture that allows NCL …

The Marked Tree Site: Evaluation Of Geosynthetic Reinforcements In Flexible Pavements, Taylor Mitchell Goldman

Graduate Theses and Dissertations

This document presents findings from a three-year, full-scale, field research project aimed at determining the benefits of using geosynthetic reinforcements to improve the performance of flexible pavements constructed over poor subgrade soils. The test site, known as the Marked Tree site, is an 850-ft (258-m) long segment of low-volume frontage road along Highway 63 in the town of Marked Tree, Arkansas. The site, constructed in 2005, consists of seventeen 50-ft (15.2-m) long flexible pavement test sections with various types of geosynthetic reinforcements (woven and nonwoven geotextiles, and geogrids), which were all positioned at the base-subgrade interface, and two different nominal …

Surface Wetting And Friction Studies Of Nano-Engineered Surfaces On Copper Substrate, Julius Sheldon Morehead

Graduate Theses and Dissertations

Nano-engineered-textures on a material surface can dramatically improve the wetting and non-wetting properties of a surface, and they also show promise to address friction issues that affect surfaces in contact. In this work, aluminum-induced crystallization (AIC) of amorphous silicon (a-Si) was used to produce nano-textures on copper (Cu) substrates. A study was performed to examine the effects of changing the annealing conditions and a-Si thickness on nano-texture formation. The creation of various nano-topographies and chemically modifying them using octafluorocyclobutane (C4F8) was performed to control hydrophilicity, hydrophobicity, and oil affinity of nano-textured surfaces. A video-based contact angle measurement system was used …

Influence Of Recycled Asphalt Shingles On Asphalt Binder Content, Mixture Stiffness, And Laboratory Rutting Performance, Joshua David King

Graduate Theses and Dissertations

Recycled asphalt shingles (RAS) is a technology in which pavement costs can be reduced significantly and pavement properties may be enhanced. Also, incorporating shingles into pavements reduces the impacts of waste shingles in landfills, preserving our environment. However, for this new technology to be practical for implementation, a better understanding of how the ground shingles affect the properties of the asphalt is necessary. The purpose of this research was to examine the effects of recycled asphalt shingles on asphalt binder content, mixture stiffness, and laboratory rutting performance. For this project, shingles were added to hot mix asphalt mixtures at 2.5, …

Development Of A Structured Concrete Thermocline Thermal Energy Storage System, Bradley M. Brown

Graduate Theses and Dissertations

The past couple of decades have shown a concern when considering the way the world obtains its power. The focus has been switching from fossil fuels that have been used for hundreds of years to renewable energy sources, such as the sun. Solar energy is readily and infinitely available for harnessing. One problem with solar energy, though, is its inability to be used during the night time and during cloud covered weather. A solution to this problem is the use of energy storage mechanisms. For solar plants that use solar thermal energy (concentrating solar power plants), thermal energy storage (TES) …

Removal Of Disinfection By-Product Precursors Using Magnetic Ion Exchange (Miex(R)): The Effects Of Ph And Source Water Variability, Sarah Cousins

Graduate Theses and Dissertations

Disinfection by-products (DBPs) form as an unintended result of drinking water disinfection, from chemical reactions between disinfectants (e.g., free chlorine) and naturally occurring dissolved organic matter (DOM). At present, 11 DBPs are regulated in treated drinking waters due to potential adverse health effects, including four trihalomethanes (THMs). Despite nearly 40 years of DBP research, compliance with DBP regulations remains a challenge for many drinking water treatment plants (DWTPs), including the four DWTPs located on the Beaver Lake Reservoir in Northwest Arkansas. Due to the high net negative surface charge on DOM, anion exchange is one potentially viable method for removing …

An Investigation Into Temperature Trending In Railroad Tapered Roller Bearings Through Vibration Monitoring Techniques, Rafael Kristian Maldonado

Theses and Dissertations - UTB/UTPA

A series of laboratory experiments have been conducted at The University of Texas-Pan American to investigate the cause of bearing “temperature trending.” A combination of theoretical and experimental studies has identified potential sources for the abrupt changes in temperature often seen in railroad bearings. Previous studies suggest the possibility of vibration induced roller misalignment as the root cause for temperature trending. Subsequent research conducted by the UTPA team was designed to provide evidence through vibration monitoring techniques for the proposed hypothesis. To that end, a dynamic bearing tester was used to run four bearings at various speeds and loads experienced …

Application Of The Empirical Mode Decomposition On The Characterization And Forecasting Of The Arrival Data Of An Enterprise Cluster, Linh Bao Ngo

Graduate Theses and Dissertations

Characterization and forecasting are two important processes in capacity planning. While they are closely related, their approaches have been different. In this research, a decomposition method called Empirical Mode Decomposition (EMD) has been applied as a preprocessing tool in order to bridge the input of both characterization and forecasting processes of the job arrivals of an enterprise cluster. Based on the facts that an enterprise cluster follows a standard preset working schedule and that EMD has the capability to extract hidden patterns within a data stream, we have developed a set of procedures that can preprocess the data for characterization …

Fabrication Of Composite Nanomaterials For Thin Film Amorphous Silicon Solar Cells, Benjamin Seth Newton

Graduate Theses and Dissertations

A material with the precise combination of amorphous silicon and polycrystalline silicon would be able to take advantage of the high absorption capabilities of amorphous silicon and the electron transport capabilities of polycrystalline silicon. Polycrystalline nanostructures in the form of wires can also take advantage of other properties of light absorption, trapping and scattering inherent in nanowire structures. These properties of high absorption and electron transport in one device would lead to advances in the search for highly efficient low cost solar cells and sensors. In this work a thin film material composed of an array of polycrystalline silicon nanostructures …

Location-Aware Traffic Management On Mobile Phones, Sarath Krishna Mandava

Graduate Theses and Dissertations

The growing number of mobile phone users is a primary cause of congestion in cellular networks. Therefore, cellular network providers have turned to expensive and differentiated data plans. Unfortunately, as the number of smartphone users keeps increasing, changing data plans only provides a temporary solution. A more permanent solution is offloading 3G traffic to networks in orthogonal frequency bands. One such plausible network is open Wi-Fi, which is free by definition. As Wi-Fi networks become ubiquitous, there are several areas where there is simultaneous Wi-Fi and 3G coverage. In this thesis, we study the feasibility of offloading 3G traffic to …

Effects Of High-Impedance-Contrast Boundary Upon Multi-Modal Seismic Surface Wave Data, Prajwol Tamrakar

UNLV Theses, Dissertations, Professional Papers, and Capstones

Synthetic studies and analyses of an experimental dataset were conducted to address the use of Rayleigh-type surface waves for estimation of shear wave velocity (VS) profiles of shallow bedrock sites. The shallow bedrock presents a high impedance contrast boundary which causes surface wave energy to be partitioned to higher modes. Idealized studies of hypothetical datasets and root-mean-squared calculations of error surfaces showed that if reliable dispersion data are available over a broad frequency spectrum, the VS profile can be recovered using the fundamental mode alone. However, when dispersion data are limited to a relatively narrow frequency band representing what might …

Sensing And Transmission Strategies In Wireless Cognitive Radio Systems, Babak Abbasi Bastami

UNLV Theses, Dissertations, Professional Papers, and Capstones

The main challenge in any cognitive radio system is to maximize secondary users throughput while limiting interference imposed on licensed users. In this regard, finding the optimal sensing and transmission timing strategies and accurate sensing techniques are of great importance in a cognitive radio network.

In this thesis, we study a sensing-transmission scheme for secondary user in a cognitive radio system where the secondary user senses every primary channel independently and transmits a signal for a fixed duration if it finds the channel empty and stays idle for another fixed duration if it senses the channel busy. We obtain optimal …

Energy-Based Analysis Of Utility Scale Hybrid Power Systems, Kwame Agyenim-Boateng

UNLV Theses, Dissertations, Professional Papers, and Capstones

The promise of large-scale use of renewables such as wind and solar for supplying electrical power is tempered by the sources' transient behavior and the impact this would have on the operation of the grid. Among the methods cited for addressing some of those concerns are exploring the complementary nature of solar and wind power generation, and through the use of supplemental energy storage. While the technology for the latter has not been proven to be economical on a large scale at the present time, some assessments of what magnitude is required can be made. An energy-based analysis of utility …

Subthreshold 3 Phase Mixers, Jesus Angel Torres

Theses and Dissertations - UTB/UTPA

This thesis will discuss subthreshold FET mixers with a focus on conversion loss derivations. To begin understanding the mixers, a look into the FET model is first taken in Chapter II. Then in Chapter III, a single FET device mixer is studied and its conversion loss is found from its small-signal model. The chapter will then include a two FET device mixer and a four device FET mixer. Finally a new type of mixer will be discussed in Chapter IV. The new type of mixer is a 3 phase mixer with the phase angles being 0°, 120°, and 240°. The …

The Role Of Thermally-Induced Geometrical Changes In Temperature Trending Of Railroad Tapered Roller Bearings, Andrei G. Vaipan

Theses and Dissertations - UTB/UTPA

The understanding of the phenomenon of temperature trending of railroad tapered roller bearings is of paramount importance to the railroad industry. The problem that this poses to the industry is that it leads to false alarms triggered by wayside detectors, which forces the premature removal of defect-free bearings. This thesis provides more insight into this phenomenon and answers questions regarding the importance of key tapered roller bearing components geometry and geometrical changes during temperature trending events. In this study, dynamic experiments conducted in the laboratory have represented the primary method of testing bearing temperature trending. The experimental results are brought …

Analysis And Design Of An Anisotropic, Compliant Suspension Component, Samantha Jean Salinas

Theses and Dissertations - UTB/UTPA

A steering pad on a train is meant to reduce the force on the wheel while moving along a curve in the rail. A new steering pad was desired with properties tuned for a new suspension system design. An anisotropic, compliant pad was designed for a specific stiffness anisotropy, 20:1. Finite element analysis was performed on various models as a guide to designing a pin with the desired stiffness ratio. A design was chosen for a prototype made of thermoset polyurethane, a similar material to that currently used. Experiments were performed on the prototype pad model to determine vertical and …

Spectroscopic Methods Of Process Monitoring For Safeguards Of Used Nuclear Fuel Separations, Jamie Lee Warburton

UNLV Theses, Dissertations, Professional Papers, and Capstones

To support the demonstration of a more proliferation-resistant nuclear fuel processing plant, techniques and instrumentation to allow the real-time, online determination of special nuclear material concentrations in-process must be developed. An ideal materials accountability technique for proliferation resistance should provide nondestructive, realtime, on-line information of metal and ligand concentrations in separations streams without perturbing the process. UV-Visible spectroscopy can be adapted for this precise purpose in solvent extraction-based separations.

The primary goal of this project is to understand fundamental URanium EXtraction (UREX) and Plutonium-URanium EXtraction (PUREX) reprocessing chemistry and corresponding UV-Visible spectroscopy for application in process monitoring for safeguards. By …

The Evaluation And Analysis Of The Impact Of Variability On The Twelve Workstation Factory, Hernando Garrido

Theses and Dissertations - UTB/UTPA

Presently, there is theory and work examples about factory performance presented in the book ―Optimizing factory Performance‖ by James Ignizio, Ph.D. The theory explains how to determine performance using three fundamental equations by considering the impact and propagation of variability through a 12-Workstation Factory Model, and a number of its variations. The objective of developing a simulation model was to serve as a tool for instructors to illustrate the impact and propagation of variability in the manufacturing industry and to investigate phenomena (i.e., time to reach steady state, impact of variability) in the three dimensions of manufacturing. The validation of …

Design Of An 866 Mhz On-Chip Frequency Synthesizer, Phaniraj Joshi

Graduate Theses and Dissertations

There is a strong need for stable frequency references with large tuning ranges in today's communication systems. While the crystal oscillators assure good frequency stability, it is not possible to achieve a large frequency range by tuning the passive components attached to them. Frequency synthesizers are usually used for this purpose because of their ability to produce a variety of output frequencies. The Phase Locked Loop (PLL) based frequency synthesizer is the most preferred of all types of synthesizers available because of its additional features like programmability, low noise and low cost as well as high accuracy and stability. The …

Adaptive Intensity Modulated Radiation Therapy Planning Optimization With Changing Tumor Geometry And Biology Enforcing Both Cumulative And Fraction Size Dose Constraints, Behlul Saka

Graduate Theses and Dissertations

Intensity Modulated Radiation Therapy (IMRT) is a modern technique of delivering radiation treatments to cancer patients. In IMRT technology, intensities must be chosen for the many small unit grids into which the beams are divided to produce a desired distribution of dose at points throughout the body with the goal of maximizing dose delivered to the tumor while sparing healthy tissues from excessive radiation and keeping dose homogeneous across the tumor. Although IMRT plans are optimized as a single overall treatment plan, they are delivered over 30-50 treatment sessions (fractions) and both cumulative and per-fraction dose constraints apply. The extended …

Improvements On Just-About-Right (Jar) Scales As Product Optimization Tools Using Kano Modeling Concepts, Bangde Li

Graduate Theses and Dissertations

Attribute Kano characteristics are useful in product design to prioritize development efforts. However, attribute Kano characteristics have not been discussed and applied to product optimization when using Just-About-Right (JAR) scales. Product optimizations without identifying attributes Kano characteristics can be misleading. The two objectives in this research were: 1. Determine attribute Kano categories using a modified classic Kano classification methodology. 2. Propose a method to measure attribute performance and identify attribute Kano characteristics to direct product optimization. Two methodologies of attribute Kano classification were investigated. In experiment one, a modified classic Kano methodology was employed to determine attribute Kano categories through …

Proteome Based Development Of Novel Affinity Tail For Immobilized Metal Affinity Chromatography And Hydrophobic Interaction Chromatography, Neha Tiwari

Graduate Theses and Dissertations

At industrial scale, reducing the step in purification and recovery is desired; this not only decreases the cost but also increases the yield. Hydrophobic Interaction Chromatography (HIC) and Immobilized Metal Affinity Chromatography (IMAC) both are not harsh on biological structure or activity of proteins; also both the techniques are economical and therefore a suitable choice at industrial level. This dissertation comprises of three parts. Purpose for the Part I was to identify and characterize Escherichia coli proteins which display affinity towards both IMAC and Hydrophobic Interaction Chromatography (HIC). Co (II) IMAC was chosen as the primary capture step, followed by …

Inventory Models For Intermittent Highly Variable Demand And Policy Parameter Adjustments To Meet Desired Service Level Requirements, Yasin Unlu

Graduate Theses and Dissertations

This dissertation consists of three assays. The first assay examines the robustness of lead time demand models for the continuous review (r;Q) inventory policy. A number of classic distributions as well as distribution selection rules are examined under a wide variety of demand conditions. First, the models are compared to each other by assuming a known demand process and evaluating the errors associated with using a different model. Then, the models are examined using a large sample of simulated demand conditions. Approximation results of inventory performance measures - ready, rate excepted number of backorders and on-hand inventory levels are reported. …

Fabrication Of Horizontal Silicon Nanowires Using A Thin Aluminum Film As A Catalyst, Khaja Hafeezuddin Mohammed

Graduate Theses and Dissertations

Silicon nanowires have been the topic of research in recent years for their significant attention from the electronics industry to grow even smaller electronic devices. The semiconductor industry is built on silicon. Silicon nanowires can be the building blocks for future nanoelectronic devices. Various techniques have also been reported in fabricating the silicon nanowires. But most of the techniques reported, grow vertical silicon nanowires. In the semiconductor industry, integrated circuits are designed and fabricated in a horizontal architecture i.e. the device layout is flat compared to the substrate. When vertical silicon nanowires are introduced in the semiconductor industry, a whole …

Integrated Planning For Rural Rail Transportation, Jeffrey Cohan Gwaltney

Graduate Theses and Dissertations

Population growth in rural areas has led to new interest in rail transportation. Planning a passenger rail system involves numerous difficult decisions, most representing a trade-off between customer service and cost. In this work, we attempt to integrate many of these planning decisions. We consider strategic decisions such as station location and vehicle procurement, as well as tactical issues that include vehicle scheduling. Our integrated model exploits the linear network structure that best suits many rural American communities, including Northwest Arkansas. Due to the intractability of the integrated rail planning problem, we have developed a customized heuristic approach to solve …