Engineering Commons^™

Just In Time Assembly (Jita) - A Run Time Interpretation Approach For Achieving Productivity Of Creating Custom Accelerators In Fpgas, Sen Ma

Graduate Theses and Dissertations

The reconfigurable computing community has yet to be successful in allowing programmers to access FPGAs through traditional software development flows. Existing barriers that prevent programmers from using FPGAs include: 1) knowledge of hardware programming models, 2) the need to work within the vendor specific CAD tools and hardware synthesis. This thesis presents a series of published papers that explore different aspects of a new approach being developed to remove the barriers and enable programmers to compile accelerators on next generation reconfigurable manycore architectures. The approach is entitled Just In Time Assembly (JITA) of hardware accelerators. The approach has been defined …

Design, Fabrication And Measurement Of A Plasmonic Enhanced Terahertz Photoconductive Antenna, Nathan Matthias Burford

Graduate Theses and Dissertations

Generation of broadband terahertz (THz) pulses from ultrafast photoconductive antennas (PCAs) is an attractive method for THz spectroscopy and imaging. This provides a wide frequency bandwidth (0.1-4 THz) as well as the straightforward recovery of both the magnitude and phase of the transmitted and/or reflected signals. The achieved output THz power is low, approximately a few microwatts. This is due to the poor conversion of the femtosecond laser used as the optical pump to useable current inside the antenna semiconducting material. The majority of THz power comes from the photocarriers generated within ~ 100 nm distance from the antenna electrodes. …

Optimal Sensing And Transmission In Energy Harvesting Sensor Networks, Xianwen Wu

Graduate Theses and Dissertations

Sensor networks equipped with energy harvesting (EH) devices have attracted great attentions recently. Compared with conventional sensor networks powered by batteries, the energy harvesting abilities of the sensor nodes make sustainable and environment-friendly sensor networks possible. However, the random, scarce and non-uniform energy supply features also necessitate a completely different approach to energy management.

A typical EH wireless sensor node consists of an EH module that converts ambient energy to electrical energy, which is stored in a rechargeable battery, and will be used to power the sensing and transmission operations of the sensor. Therefore, both sensing and transmission are subject …

Interactive Physics And Characteristics Of Photons And Photoelectrons In Hyperbranched Zinc Oxide Nanostructures, Garrett Edward Torix

Graduate Theses and Dissertations

As is commonly known, the world is full of technological wonders, where a multitude of electronic devices and instruments continuously help push the boundaries of scientific knowledge and discovery. These new devices and instruments of science must be utilized at peak efficiency in order to benefit humanity with the most advanced scientific knowledge. In order to attain this level of efficiency, the materials which make up these electronics, or possibly more important, the fundamental characteristics of these materials, must be fully understood. The following research attempted to uncover the properties and characteristics of a selected family of materials. Herein, zinc …

Sugarcane Bagasse Hydrolysis Enhancement Using Bsa, Antonio Carlos Freitas Dos Santos

Open Access Theses

Lignocellulose is composed of polysaccharides linked to lignin and other aromatic compounds, making the sugars not readily available to fermentation. This entails that biomass must go through the unit operations of pretreatment and enzyme hydrolysis. Pretreatment opens the structure to allow the enzymes to act on and hydrolyze cellulose and hemicellulose to glucose and/or xylose which in turn are fermented to ethanol. Concomitantly, the enzymes interact with soluble phenols and insoluble solids derived from lignin that inhibit hydrolysis. This leads to high enzyme loadings and higher production costs. Soluble phenols can be eliminated through washing. Insoluble lignin, however, demands another …

Assessing Fuel Burn Inefficiencies In Oceanic Airspace, Stephen Builta

Open Access Theses

Increasing the efficiency of aircraft operations offers a shorter term solution to decreasing aircraft fuel burn than fleet replacement. By estimating the current airspace inefficiency, we can get an idea of the upper limit of savings. Oceanic airspace presents a unique opportunity for savings due to increased separation differences vs. overland flight.

We assess fuel burn inefficiency by comparing estimated fuel burn for real world flights with the estimated optimal fuel burn. For computing fuel burn, we use the Base of Aircraft Data (BADA) with corrections based on research by Yoder (2005). Our fuel burn results show general agreement with …

Multimedia Techniques For Construction Education And Training, Wayne A. Bunnell

Open Access Theses

The current profession of civil engineering often focuses education and training on code compliance rather than constructability and construction techniques. Also, it is well accepted that it takes a decade or more for engineers to develop a high-level project construction understanding and many state departments of transportation rely on in-field training for entry-level inspectors, with little or no education provisions for contractors. This research investigated the use of time-lapse photography to develop training and education material that will improve the understanding of project construction and crucial quality control specifications of an entry-level engineer, contractor, or inspector. Overall, the project team …

Size Scaling Of Strength And Toughness For 3d Printed Polymer Specimens, Darren Thomas Bell

Open Access Theses

To find material systems that offer low density and high strength, stiffness or toughness, hierarchically designed material systems have provided a promising research area. This thesis lays the groundwork for designing efficient micro-architectured material systems by characterizing size effects for 3d printed polymer parts. Two methods were used to analyze data from 3-point bend tests for specimens of varying size: the load-separation method was used for finding the point of crack growth initiation and Bazant’s method was used to find shape independent strength at failure. The strength values were used as inputs for finding size independent material constants within a …

Mechanism Of Shot Peening Enhancement For The Fatigue Performance Of Aa7050-T7451, Daniel James Chadwick

Open Access Theses

Shot peening is a dynamic cold working process involving the impingement of peening media onto a substrate surface. Shot peening is commonly employed as a surface treatment technique within the aerospace industry during manufacturing, in order to improve fatigue performance of structural components. The compressive residual stress induced during shot peening is understood to result in fatigue crack growth retardation, improving the performance of shot peened components. However, shot peening is a compromise between the benefit of inducing a compressive residual stress and causing detrimental surface damage. Due to the relatively soft nature of AA7050-T7451, shot peening can result in …

Printing 3d Lithium-Ion Microbattery Using Stereolithography, Qiming Chen

Open Access Theses

Microbatteries have been gained a lot of importance since the development of micro- and nanotechnologies. Integrating the microbattery system will enable a variety of applications, such as implantable biomedical devices and wireless sensor networks. In this paper, we demonstrated a new method to fabricate three dimensional lithium-ion microbattery using stereolithiography. A UV-curable gel polymer electrolyte resin is first synthesized and characterized. The electrolyte resin is then applied to build into 3D architecture by stereolithography. The gel electrolyte structure is designed into a zigzag shape in order to improve the contact area between electrode and electrolyte. Battery's active material, LiFePO4 (LFP) …

Tangible Interaction As An Aid For Object Navigation In 3d Modeling, Sanmathi Dangeti

Open Access Theses

This study introduced an interaction technique that used tangible interaction for 3D modeling. A hybrid interaction technique using a Kinect camera and a smartphone with a gyroscope was developed for the navigating objects in a 3D modeling software. It was then tested on 20 participants categorized as amateurs who had basic 3D/ CAD modeling experience and 20 participants categorized as the experts who had extensive experience working with the modeling software. This research study presents the need for existence of such interaction technique, gaps from the related previous studies, statistical findings from the current study and possible reasons for the …

Taming Tail Latency For Erasure-Coded, Distributed Storage Systems, Jingxian Fan

Open Access Theses

Nowadays, in distributed storage systems, long tails of responsible time are of particular concern. Modern large companies like Bing, Facebook and Amazon Web Service show that 99.9th percentile response times being orders of magnitude worse than the mean. With the advantages of maintaining high data reliability and ensur- ing enough space eciency, erasure code has become a popular storage method in distributed storage systems. However, due to the lack of mathematical models for analyzing erasure-coded based distributed storage systems, taming tail latency is still an open problem.

In this research, we quantify tail latency in such systems by deriving a …

An Investigation Of Composite Failure Analyses And Damage Evolution In Finite Element Models, Ann M. Frappier

Open Access Theses

This paper presents a composite conical structure used commonly in flight-qualification testing. This structure’s overall load-displacement behavioral response is characterized. Mixed-mode multidelamination in a layered composite specimen is considered in Abaqus/Explicit through both the Virtual Crack Closure Technique and Cohesive Elements. The Virtual Crack Closure Technique and Cohesive Elements are compared against experimental test results presented in literature. Further, a thorough comparison in which the effects of failure criteria type, through-thickness mesh density, and finite element type on the progressive failure response of this composite assembly is discussed. Lastly, Abaqus/Standard and Helius PFA are compared in order to gain confidence …

Thermal Transport In Lithium Ion Batteries: An Experimental Investigation Of Interfaces And Granular Materials, Aalok Jaisheela Uday Gaitonde

Open Access Theses

Increasing usage and recent accidents due to lithium-ion (Li-ion) batteries exploding or catching on fire has inspired research on the characterization and thermal management of these batteries. In cylindrical 18650 cells, heat generated during the battery's charge/discharge cycle is poorly dissipated to the surrounding through its metallic case due to the poor thermal conductivity of the jelly roll, which is spirally wound with many interfaces between electrodes and the polymeric separator. This work presents a technique to measure the thermal conduction across the metallic case-plastic separator interface, which ultimately limits heat transfer out of the jelly roll.

The polymeric separator …

Design Of Nitroxide-Based Radical Polymer Materials For Electronic Applications, Martha E. Hay

Open Access Theses

Radical polymers represent a new class of organic electronic materials that rely on an oxidation-reduction (redox) reaction to transport charge. That is, stable radical sites pendant to the polymer backbone communicate electronically through a rapid oxidation-reduction reaction. This redox mechanism has previously been established as effective for charge-storage applications (e.g., secondary batteries). When applied in the solid state, radical polymers demonstrate electrical conductivity on par with that of first-generation conjugated polymer electronic materials. This initial success has prompted interest in developing design rules for radical polymers. Specifically, this thesis explores the impact of radical density in a polymer …

Design And Plan Of A Modified Hydroponic Shipping Container For Research, John A. Houtman

Open Access Theses

As the world’s population continues to increase, food production will need to increase in order to meet the predicted rise in food demand. However, with increased pressure on cropland available from environmental effects and urbanization, new innovative methods of crop production need to be researched in order to increase agricultural production with limited land. This research focuses on the design of a single form of urban agriculture that is considered Zfarming and has the potential to produce quality urban agricultural produce through ground-based measures. This project produced detailed step-by-step analysis of the design process, develop variability within the modified hydroponic …

Improvement Of A Biomechanical Telemetry System Hardware Platform, Soon Ho Kwon

Open Access Theses

Traumatic brain injuries (TBI) while playing sports are a major concern for the general public today. Recently, studies have shown that repetitive subconcussive hits can lead to neurological disorders. In order to prevent the athletes from suffering traumatic brain injuries, many organizations related to contact based sports and the military employ commercialized head impact telemetry systems. However, a majority of the commercialized systems is event based which only collects the linear acceleration that exceeds a certain threshold. To accurately record and utilize the data from the impact telemetry system, it is necessary to record all the linear and angular acceleration …

Video Annotation By Crowd Workers With Privacy-Preserving Local Disclosure, Apeksha Dipak Kumavat

Open Access Theses

Advancements in computer vision are still not reliable enough for detecting video content including humans and their actions. Microtask crowdsourcing on task markets such as Amazon Mechnical Turk and Upwork can bring humans into the loop. However, engaging crowd workers to annotate non-public video footage risks revealing the identities of people in the video who may have a right to anonymity.

This thesis demonstrates how we can engage untrusted crowd workers to detect behaviors and objects, while robustly concealing the identities of all faces. We developed a web-based system that presents obfuscated videos to crowd workers, and provides them with …

Flammability Limits Of Alternative Aviation Fuels, Ang Li

Open Access Theses

Alternative aviation fuels are being developed recently to partially replace the limited resources of traditional liquid fuels in the aviation industry. The fire-safety properties of these fuels, however, are unknown. Especially, the flammability limit of a fuel is a crucial parameter. The present work focuses on measurements of concentration and temperature flammability limits of four pure hydrocarbon fuels, as well as traditional and alternative aviation fuels, including Jet-A, HEFA, SIP, and FT-S8. The lower and upper concentration flammability limits of these selected fuels were determined under specific temperatures and pressures. An experiment including a customized power supply system to generate …

Degradation Of High Performance Polymeric Fibers: Effects Of Sonication, Humidity And Temperature On Poly (P-Phenylene Terephthalamide) Fibers, Nelyan Lopez-Perez

Open Access Theses

High performance fibers are characterized by properties such as high strength and resistance to chemicals and heat. Due to their outstanding properties, they are used on applications under harsh environments that can degrade and decrease their performance. Fiber degradation due to different chemical and mechanical factors, is a process that begins at a microstructural level. Changes in the polymer’s chemical or physical structure can alter their mechanical properties. Knowledge of the structure-properties relationship and the effects of environmental chemical and physical factors over time, is crucial for the improvement and development of high performance fibers.

In this study ballistic fibers …

Mathematical Analysis Of Feedback Targets Of Bmp Signaling In Drosophila Embryonic Development, Yan Luo

Open Access Theses

Bone morphogenetic proteins (BMPs) drive a range of cellular processes especially in the early stages of embryonic development. This family of proteins acts as one of the most important extracellular signals in development pattern formation across the animal kingdom. Cells in embryos differentiate into different cell types in response to the concentration level of BMP. This complex process is regulated by multiple regulators that serve to tune the signal response.

Extensive experimental and computational research has been performed to analyze BMP regulation in Drosophila, a widely studied model organism, and has advanced our understanding of animal development. Because of …

New Screening Method For Overweight Vehicles, Goran Veljko Milutinovic

Open Access Theses

Throughout the U.S., state agencies are issuing an increasingly large number of permits for overweight vehicles every year. There are various methods used by state agencies to process permit requests; the Indiana Department of Transportation employs a screening process that consists of the Tennessee Formula (allowable weight is determined and checked, for every axle group) in combination with the Gross Vehicle Weight limit. If a permit truck satisfies these two screening criteria, it is permitted; otherwise, it is further processed with refined analyses. The Tennessee Formula is based on Allowable Stress Design. However, most design and evaluation conducted today is …

Quantifying Asphalt Emulsion-Based Chip Seal Curing Times Using Electrical Resistance Measurements, Miguel A. Montoya Rodriguez

Open Access Theses

Chip seals are among the most cost-effective surface treatments available for asphalt pavement preventive maintenance. Chip sealing typically consists of covering a pavement surface with asphalt emulsion into which aggregate chips are embedded. The asphalt emulsion cures through the evaporation of water, which helps to provide mechanical strength for the chip seal. Ultimately, the curing process enables the emulsion to adhere to the pavement while keeping the aggregate chips in place. The curing time for the chip seal depends on many factors, such as the asphalt emulsion and aggregate types, aggregate moisture content, emulsion and aggregate application rates, and environmental …

In-Situ Particle Sizing Of Agglomerates In Aluminized Solid Composite Propellants Using Digital Inline Holography (Dih), Michael S. Powell

Open Access Theses

Aluminized ammonium perchlorate composite propellants (APCP) form large molten agglomerated particles that can result in poor combustion performance and increased two-phase flow losses. Quantifying agglomerate size distributions is important for assessing these losses for different types of aluminum fuels that can help improve rocket performance. It is highly desirable to measure particle sizes in-situ using non-intrusive optical methods, rather than conventional particle collection, which can have large uncertainties. Regular high-speed microscopic imaging suffers from a limited depth of field. Digital inline holography (DIH) is an alternative approach that results in 3D information through numerical reconstruction. In this paper, DIH approach …

Reaction Tuning Of Selectively Deposited Nano-Thermite Inks For Thrust And Heat Deposition, Raghav Ramachandran

Open Access Theses

Currently there is very little systematic work that quantifies the performance of energetic materials in terms of thrust or heat deposition applied to electronic circuits. A better understanding of the interactions between nano-scale energetic materials and electronic systems, as a function of stoichiometry is needed for enhanced defeat. Both of these needs are addressed in this research. Formulations of Al-CuO and Al-Bi2O3 nano-thermites were prepared at different equivalence ratios and selectively deposited onto silicon substrates and thrust and heat deposition of these materials was quantified. Both nano-thermite systems produced maximum thrust near stoichiometric ratios, and more fuel-rich mixtures led to …

Liquid Metal Particle Popping: Nanoscale To Macroscale, Trevor R. Lear

Open Access Theses

Liquid metal nanoparticles can be used to produce stretchable electronic devices. Understanding the mechanical properties of liquid metal nanoparticles is crucial to optimizing their use in various applications, especially printing of flexible, stretchable electronics. Smaller nanoparticles are desired for high-resolution printing and compatibility with existing scalable manufacturing methods; however, they contain less liquid metal and are more difficult to rupture than larger particles, making them less desirable for post-processing functionality. This study investigates the mechanics of liquid metal particle rupture as a function of particle size. We employ compression of particle films to characterize the composition of the particle core …

Linking Nanoscale Mechanical Behavior To Bulk Physical Properties And Phenomena Of Energetic Materials, Matthew R. Taw

Open Access Theses

The hardness and reduced modulus of aspirin, RDX, HMX, TATB, FOX-7, ADAAF, and TNT/CL-20 were experimentally measured with nanoindentation. These values are reported for the first time using as-received micron sized crystals of energetic materials with no additional mechanical processing. The results for TATB, ADAAF, and TNT/CL-20 are the first of their kind, while comparisons to previous nanoindentation studies on large, carefully grown single crystals of the other energetic materials show that mechanical properties of the larger crystals are comparable to crystals in the condition they are practically used. Measurements on aspirin demonstrate the variation that can occur between nanoindentation …

The Influence Of Alkalinity Of Portland Cement On The Absorption Characteristics Of Superabsorbent Polymers (Sap) For Use In Internally Cured Concrete, Juan D. Tabares Tamayo

Open Access Theses

The concrete industry increasingly emphasizes advances in novel materials that promote construction of more resilient infrastructure. Due to its potential to improve concrete durability, internal curing (IC) of concrete by means of superabsorbent polymers (SAP) has been identified as one of the most promising technologies of the 21st century. The addition of superabsorbent polymers into a cementitious system promotes further hydration of cement by providing internal moisture during the hardening and strength development periods, and thus limits self-desiccation, shrinkage, and cracking.

This thesis presents the work performed on the series of cement pastes with varying alkalinity of their pore solutions …

Characterization Of A Hypersonic Quiet Wind Tunnel Nozzle, Cameron J. Sweeney

Open Access Theses

The Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University has been able to achieve low-disturbance flows at high Reynolds numbers for approximately ten years. The flow in the nozzle was last characterized in 2010. However, researchers have noted that the performance of the nozzle has changed in the intervening years. Understand ing the tunnel characteristics is critical for the hypersonic boundary-layer transition research performed at the facility and any change in performance could have signif icant effects on research performed at the facility. Pitot probe measurements were made using Kulite and PCB pressure transducers to quantify the performance changes since characterization …

Helical Strakes On High Mast Lighting Towers And Their Effect On Vortex Shedding Lock-In, Ayah Zahour

Open Access Theses

An experimental study on the effect of helical strakes on vortex induced vibrations and the lock-in phenomenon in High Mast Lighting Towers (HMLTs) is investigated. Two multi-sided tapered scaled models are clamped in place in a subsonic wind tunnel that is equipped with a hot-wire sensor and a traverse mechanism. The shedding frequency data is collected for the models with and without helically patterned strakes with the use of two different ropes. The responses of the tower models, for a Reynolds number of 44, 000, are compared and discussed under different configurations including: two directions of the model with respect …