Engineering Commons^™

Experimental Measurement Demonstration Of Initial And Steady-State Heights Of A Co2 Vertical Jet Fountain In Still Air, Brock Mcrae

Chemical Engineering Undergraduate Honors Theses

Atmospheric releases of heavier-than-air gases pose acute near-field hazards in low wind, yet the near-source behavior of vertical dense-gas jets in still air is sparsely documented. This thesis demonstrates a repeatable laboratory method for measuring the initial and steady-state rise heights of a carbon dioxide (CO₂) jet issued vertically from a floor nozzle in the CHRC ultra-low-speed wind tunnel under still-air conditions. Controlled mixtures (pure CO₂, 50/50 CO₂-air, 25/75 CO₂-air) were released at four flow rates (75, 100, 125, 150 LPM) with five repeats per condition. A fixed camera and tape-measure scale enabled video extraction of jet height using Kinovea …

Adaptive Deep Learning In Physical Layer Applications, Ali Owfi

All Dissertations

Traditionally, signal processing models in communication systems have been designed based on solid foundations in statistics and information theory, often assuming linearity and optimizing for simplified models. However, real-world communication systems exhibit numerous imperfections and non-linearities that traditional linear models struggle to capture accurately. Deep Learning (DL)-based approaches, unconstrained by rigid mathematical models, have shown promise in optimizing system performance by accommodating specific hardware configurations and dynamic channel conditions as an alternative to the traditional methods. Despite all the recent research efforts on DL-based methods for physical layer applications, DL models have still not been widely applied to physical layer …

Friction And Texture Evaluation Of Asphalt-Based Binders As Alternatives To Epoxy-Based High-Friction Surface Treatments, Alireza Roshan, Magdy Abdelrahman

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

High-friction surface treatment (HFST) is a safety-focused pavement treatment that restores and maintains pavement friction to reduce road accidents. Traditional epoxy-based HFSTs, while widely used, face challenges such as high costs, potential compatibility issues with the substrate pavement, and long-term durability under specific conditions. This study investigates asphalt-based alternative HFST, which is compatible with various pavement types and cost-effective and versatile solutions for a wider range of pavement applications. Performance and friction testing, including the British pendulum test, British wheel test, and dynamic friction test, were performed to examine the coefficient of friction (COF) before and after polishing with a …

Using Noninvasive Calibrated Cuff Plethysmography To Observe The Effects Of Lifestyle Habits On Arterial Compliance, Joshua M. Whitaker

Master's Theses

Cardiovascular disease remains as a leading cause of death for both sexes and across all racial backgrounds. Continuing to research causes, early predictors, and preventative actions are paramount to ensuring that cardiovascular disease starts to decrease in its activity. Endothelial dysfunction is the earliest known predictor of cardiovascular disease, therefore investigating early detection methods of endothelial dysfunction can improve health outcomes. This study revolves around a non-invasive calibrated cuff device that uses the principles of segmental plethysmography and oscilliometry to measure arterial compliance of baseline and induced hyperemic conditions in human subjects to determine how well arteries vasodilate in response …

Draft Genome Sequences Of Four Phosphate-Solubilizing Microbes Of The Family Burkholderiaceae Isolated From Tailings From The Former Pea Ridge Mine In Washington County, Mo, Usa, Prince Oppong Amoh, Abiodun E. Idowu, Elizabeth R. Grube, Melanie R. Mormile, Hunter W. Schroer

Biological Sciences Faculty Research & Creative Works

We present draft genome sequences of four Gram-negative phosphate-solubilizing microbes isolated from Pea Ridge Mine tailings in Missouri, USA. Belonging to the family Burkholderiaceae, these isolates exhibit a phosphate-mineral-dissolving phenotype in liquid and solid cultures. Genome sizes span 5.6–9.7 Mb, with GC contents of 61.6%–67.0%.

Mechanics Post-Tavr For Trileaflet Vs Bicuspid Aortic Valves: Insights From Computational Simulation, Breandan B. Yeats, Aniket Venkatesh, Sri Krishna Sivakumar, Hoda Hatoum, Milad Samaee, Venkateshwar Polsani, Et. Al.

Michigan Tech Publications

Background: Bicuspid aortic valve (BAV) disease is the most common congenital heart defect and is associated with elliptical openings and excess calcification. Limited data are available on long-term efficacy of transcatheter aortic valve replacement (TAVR) for BAV patients.

Objectives: The purpose of this study was to compare simulated mechanical metrics post-TAVR between BAV and trileaflet patients with calcific aortic stenosis.

Methods: Pre-TAVR computed tomography scans of trileaflet (n = 22) and BAV (n = 25) were used to segment the aortic valve. Simulated balloon-expandable stent deployment was performed from a previously developed protocol. The bioprosthetic leaflets were then pressurized under …

Evaluating The Preparedness Of Local Zoning Regulations For Flood Risk Reduction In The Most Affected Local Jurisdictions In Nebraska, Md Asaduzzaman Noor

Community and Regional Planning Program: Theses

Flooding has profound social, economic, and environmental impacts on local communities, and zoning plays a critical role in mitigating these risks. The 2019 Nebraska floods, among the most severe in the state’s history, highlighted the urgent need to strengthen local preparedness and mitigation strategies. This study assesses the extent to which local zoning regulations in Nebraska’s most affected jurisdiction, including rural areas, address flood risk reduction. A systematic review of 117 zoning ordinances from counties, cities, towns, and villages, we applied a structured analytical framework encompassing regulatory and permitting policies, voluntary and incentive-based measures, and nature-based solutions. The results show …

Platforming For Circuit Education, Grady Oliver Schneider

Computer Engineering

The purpose of this project was to provide an alternative for students being introduced to resistive circuits. As a freshman in electrical engineering (transferred to computer engineering), I saw the struggles of other freshman to grasp the conceptual basics of circuits. While there’s lots of guides to circuit education, I think many of them fall short of being both engaging and teaching the intuition behind circuits. A lot of the more advanced concepts in circuits depends on the basic intuition of KCL, KVL, and Ohm’s Law. While there’s several basic techniques (such as voltage divider, current divider, and mesh current …

Digital Solutions For Bridging Language Barriers: Designing And Testing An App For Construction Spanish Safety Communication On Construction Jobsites, Adrian Cappella

All Theses

Language barriers between English-speaking supervisors and Spanish-speaking workers create safety risks on U.S. construction jobsites. Hispanic workers face higher injury and fatality rates, with miscommunication being a major contributing factor. Existing translation tools lack the accuracy, cultural context, and jobsite relevance needed for effective safety communication.

In this study a mobile application with construction-specific safety phrases in English and Spanish was designed and field tested. The research included a literature review, phrase collection and validation with industry experts, application development and design with a computer science collaborator, and usability testing with supervisors and workers. Surveys and field trials measured navigation, …

Capillary Imbibition Of Shear-Thinning Xanthan Gum Solutions, Aimee Sayster

All Theses

Capillary rise in confined geometries plays a critical role in numerous natural and industrial processes. While classical models such as the Lucas–Washburn equation accurately describe the dynamics of Newtonian fluids, they fail to capture the complex behavior of shear-thinning, non- Newtonian fluids whose viscosity varies with shear rate. This research investigates the capillary rise dynamics of shear-thinning xanthan gum polymer solutions in capillary tubes. The rheological behavior of each fluid is characterized using the Ellis model, which accounts for shear-thinning effects through three key parameters: zero-shear viscosity μ0, characteristic shear stress τ1/2 and viscosity index α. Experimental data was collected …

Dendrimer Gel Nanoparticles With Dual-Targeting Of Upar And Ribonucleotide Reductase R2 Influence Necrosis, Apoptosis, And Cell Cycle Arrest In Triple-Negative Breast Cancer, Hsin Yin Chuang, Yue-Wern Huang, Hu Yang

Biological Sciences Faculty Research & Creative Works

Triple-negative breast cancer (TNBC) is an aggressive breast cancer subtype with limited treatment options due to the absence of estrogen (ER), progesterone (PR), and human epidermal growth factor receptor 2 (HER2) receptors. We previously developed highly adaptable polyamidoamine (PAMAM) dendrimer-based gel nanoparticles (GDP-uPA/GTI) with dual-targeting capabilities against urokinase-type plasminogen activator receptor (uPAR) and ribonucleotide reductase R2 (R2) to achieve selective antitumor effects. In this study, we investigated the underlying mechanisms of GDP-uPA/GTI-induced tumor inhibition. In vivo, GDP-uPA/GTI significantly downregulated R2 expression and activated caspase 8 and caspase 3, indicating caspase-dependent apoptosis. Histological evaluation of major organs revealed no observable toxicity. …

Elucidating Differences In Constitutionally Isomeric Diamine- And Bisphenol-Based Polybenzoxazine Networks, Benjamin L. G. Morasch

Dissertations

This dissertation aims to expand the fundamental understanding of diamine-based benzoxazine chemistry by examining how synthesis influences the network properties of 4,4’-ddm and phenol-based (P-ddm) benzoxazine, compared to the constitutionally isomeric bisphenol-F and aniline-based (BF-a) benzoxazine. While bisphenol-based benzoxazines such as BF-a have been studied more extensively, diamine-based benzoxazines are still relatively unexplored due to the competition with the formation of 1,3,5-hexahydrotriazine intermediates and the inconsistent thermal and mechanical properties reported in the literature. These inconsistencies stem from factors including synthetic methods, curing conditions, and degradation during polymerization that have been overlooked.

To address these issues, this dissertation is organized …

Upcycling Commodity Polymers To Advanced Materials For Energy And Environmental Sustainability, Anthony Griffin-Espinoza

Dissertations

Synthetic polymers play an essential role in nearly every aspect of our lives. Extending beyond single-use packaging, polymeric material design has progressed to attain tailorable architectures granting exceptional performance across advanced applications, including carbon-fiber reinforced polymer composites for aerospace, conductive materials for soft electronics, and drug carriers for biomedicine. While highly promising, intricately designed polymers needed to achieve excellent performance often have limited processability, complex synthetic methods, and expensive precursors. Furthermore, due to a lack of recyclability, commodity polymer waste streams result in both environmental impacts and a substantial loss of economic value. This dissertation focuses on developing robust strategies …

Privacy Preserving-Based Artificial Intelligence For Precision Agriculture, Partha P. Sengupta

Dissertations

The research work finds a solution to precision agriculture of cotton cultivation using artificial intelligence (AI) models. Two sets of model performance based on the application are selected namely a low resource and a high resource setting. This is because using drone surveys to capture images identifying the classes of stressed and unstressed cotton plantation requires limited model architecture and CPU based computation. Thus, traditional AI models were selected for low resource settings. Again, for high computation intensive models like transfer learning-convolution neural network (CNN) based architectures were grouped into high resource settings. There was another issue of class imbalance …

Understanding Crystallization Behaviors Of Polyethylene-Derived Vitrimers, Sara Valdez

Dissertations

Polyolefins (POs), particularly polyethylene (PE) and polypropylene (PP), are among the most widely utilized polymers globally, valued for their low production costs and favorable mechanical properties stemming from their semicrystalline microstructure. However, their extensive use and improper disposal have raised serious environmental and human health concerns. In response, PO-derived covalent adaptable networks (CANs) have emerged, integrating dynamic chemistries to enable recyclability and sustainable end-of-life strategies. While existing literature has largely focused on novel CAN systems, structure–property relationships, and network rearrangement in relation to thermal transitions (e.g., topological freezing temperature), the influence of network formation on crystallinity and crystallization kinetics remains …

Steel-Concrete Composite Girder Experiments To Isolate Interface Load Transfer Effects On Stud Fatigue Life, Marc Crespi Hromcova

Graduate Theses and Dissertations

Metal fatigue resulting from repeated loading is a primary limit state that affects the quantity of headed shear studs required in the composite design of steel bridge girders. While concrete-deck-to-steel-superstructure load transfer is only considered through stud bearing in the American Association of State Highway Transportation Officials (AASHTO) design standards, friction and interface interlocking effects may also contribute. This study aims to experimentally quantify the effect of interface conditions on the fatigue life of headed studs within composite girders. In this study, two full-scale composite girder specimens having the same geometry and material properties are tested with two interface conditions. …

Optimizing Indigenous Timber Short-Gap Crossing Designs By Minimizing Wood Moisture Content, Robert Greenwood

Graduate Theses and Dissertations

Reducing moisture content increases wood strength and reduces the weight of timber members. An accurate and efficient method for measuring moisture content is important for the design and construction of indigenous timber short-gap crossings. This study evaluates different methods for measuring moisture content in timber, describes a methodology for developing a representative moisture content value for a timber log, and approaches for quickly drying large timber logs. The results of this thesis will support activities in developing a representative moisture content of a log for structural design purposes and reducing weight for constructability purposes. The approaches discussed were developed considering …

Toward A Better Understanding Of Friction, Adhesion, And Stud Bearing Shear Transfer At The Steel-Concrete Interface Of Composite Bridge Girders, Callie Grace James

Graduate Theses and Dissertations

Following curing of the concrete deck, load transfer between the concrete and steel components in a composite bridge girder is possible through three mechanisms: 1) mechanical contact (bearing) between the embedded shear connectors and surrounding cured concrete, 2) adhesion between the cured concrete and steel-section top flange, and 3) friction between the contacting materials Understanding the mechanisms of bearing, adhesion, and friction shear transfer at the steel-concrete interface of composite bridge girders is necessary for efficient proportioning of headed shear connectors (or studs) in design. To better understand the roles that stud bearing, adhesion, and friction play in composite girder …

Optimization Of Energy Management In Malaysian Microgrids Using Fuzzy Logic-Based Ems Scheduling Controller, Mohammad Nur-E-Alam, Tarek Abedin, Nur Aini Samsudin, Jana Petrů, Abdulwasa Bakr Barnawi, Manzoore Elahi M. Soudagar, T. M.Yunus Khan, Muhammad Nasir Bashir, Mohammad Aminul Islam, Boon Kar Yap, Tiong Sieh Kiong

Research outputs 2022 to 2026

The microgrid (MG) faces significant security issues due to the two-way power and information flow. Integrating an Energy Management System (EMS) to balance energy supply and demand in Malaysian microgrids, this study designs a Fuzzy Logic Controller (FLC) that considers intermittent renewable sources and fluctuating demand patterns. FLC offers a flexible solution to energy scheduling effectively assessed by MATLAB/Simulink simulations. The microgrid consists of PV, battery, grid, and load. A Maximum Power Point Tracking (MPPT) controller helps to extract the maximum PV output and manages the power storage by providing or absorbing excess power. System analysis is performed by observing …

Confinement-Dependent Transient Mi For The Hoek-Brown (H-B) Strength Criterion, Hao Li, Leo Pel, Zhenjiang You, David Smeulders

Research outputs 2022 to 2026

The growing global demand for mineral resources necessitates deeper excavation, where increasing in situ stresses pose significant geomechanical challenges. Consequently, an accurate strength assessment of deep-seated rock masses is crucial for ensuring the safety and reliability of underground excavations. The Hoek-Brown (H-B) strength criterion remains a widely applied rock strength criterion. However, its conventional form struggles to characterize the full nonlinear evolution of rock strength from pre-critical to critical conditions across varying confining stresses. To address this limitation, this study proposes a Confinement-dependent Transient mi Model (CTM) as an enhancement to the H-B criterion. By incorporating confinement-sensitive variations of mi, …

Data Center Composite Load Model Parameters’ Tuning, Mohammed Sleiman, Amirreza Sahami, Oluwatimilehin Adeosun, Nathaniel Rice, Katelyn Vance

Electrical and Computer Engineering Faculty Research & Creative Works

The vast expansion of data center campuses has created concentrated and highly dynamic electrical loads that challenge traditional transmission system planning and protection studies. This paper presents a novel approach to model the load of data centers and validate their dynamic performance in a composite-load-model (CMLD) framework.

The data center has three major modules: a static element representing the static devices and busway impedance; an electronic-based element constituting power converters such as rectifiers and inverters, associated power supplies, and a motor-based element encompassing the induction nature of chillers, fans and pumps. Each module represented equivalent algebraic and differential equations depicting …

Bone Void Filler Materials For Augmentation In Comminuted Fractures: A Comprehensive Review, S. Sina Mohammadi, Sunjeev S. Phull, B. Sonny Bal, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Comminuted fractures, characterized by multiple bone fragments, present significant challenges in orthopedic surgery. Effective treatment often requires augmentation techniques to enhance fixation stability and promote bone regeneration. This review explores the application of bone void filler materials, including autografts, allografts, polymethyl methacrylate (PMMA), and synthetic bone substitutes such as calcium phosphate ceramics and bioactive glass, in managing comminuted fractures. Autografts are the gold standard due to their superior osteogenic potential but are limited by donor site morbidity and availability. Allografts mitigate these issues but face concerns regarding immunogenicity and reduced biological activity. PMMA, widely used for structural augmentation, provides immediate …

Local Hydrodynamics And Phase Distribution In Large-Scale Trickle Bed Reactors Using Multi-Detector Γ-Ray Densitometry, Sebastián Uribe, Ahmed Jasim, Saba A. Gheni, Nora Selem, Nouhaila Filali, Tiberiu M. Leib, Sourav Sengupta, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

This study presents a new approach of using gamma ray computed tomography (CT) in a form of arc multi-detector γ-Ray Densitometry (Arc MD-GRD) Technique where it measures the line averaged holdups of the phases which are projected on the diameter of the column to obtain their diameter profiles. This technique then was used to investigate the diameter profiles of the phases' holdups in a 12-inch diameter trickle bed reactor (TBR) using sulfur hexafluoride (SF6) as the gas phase to represent to a certain extent the industrial higher density of the used gas phase due to either the type of the …

Unlocking The Potential Of Copper Sulfide Tailings As A Secondary Source For Tellurium And Precious Metals: A Comprehensive Characterization Study, Fardis Nakhaei, Lana Alagha, Gary Wyss

Mining Engineering Faculty Research & Creative Works

This study investigated historical copper sulfide tailings as an unconventional source of tellurium (Te), gold (Au), and silver (Ag). Advanced analytical studies were conducted to determine the geochemical and mineralogical properties of the tailing samples. The results showed that tetradymite (Bi2Te2S) was the predominant Te-bearing mineral, while hessite (Ag2Te) was a minor Te carrier, both notably occurring within fine-grained (< 8 μm) inclusions in pyrite. Gold was present as native Au, electrum (Au-Ag), and within complex silver tellurides hosted primarily in chalcopyrite and pyrite. Froth flotation studies showed that the 180 to 38 μm size range was the optimum feed size that yielded recoveries of 59 %, 37 %, and 27 % for Te, Au, and Ag, respectively. These findings suggested that froth flotation is a feasible method for concentrating Te-Au-Ag-bearing phases. Given the strong association between Te, Au, Ag, and Cu, the co-extraction of these metals should significantly enhance the economic viability of tailings' processing.

Investigating The Correlation And Synergy Of Artificial Intelligence Techniques, Construction Technologies, And Their Key Benefits, Fareed Salih, Islam H. El-Adaway

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Despite its reputation as one of the least digitized sectors, the construction industry increasingly adopts artificial intelligence (AI) and construction technologies. However, previous research has not adequately explored the benefits of AI techniques and construction technologies nor the correlations between them. This study aims to fill this knowledge gap. To this end, the authors used a multistep research methodology. First, a systematic literature review of studies published between 1985 and 2022 was conducted to identify AI techniques and construction technologies. Second, content and frequency analysis were performed to determine the benefits associated with AI and technology adoption. Finally, a survey …

Computational Fluid Dynamics Based Optimization Method Applied To Hydrokinetic Turbine Devices, Stuart Glenn Fletcher

Graduate Theses and Dissertations

This thesis presents a computational investigation of optimal kinematic operating parameters governing various hydrokinetic turbines (HKT) systems for the use of power generation within river and tidal environments. Two separate studies are performed. The first study investigates optimal cycle parameters for simple and complex kinematic modes governing the motion of oscillating foil energy harvesters (OFEH). An iterative gradient-ascent optimization method is used to search for local efficiency optima based on an initial set of kinematic parameters. To search the operational space for up to eight degrees of freedom (DOF), a maximin space filling condition was implemented to efficiently compute initial …

Validation Studies Of A Dynamic Hybrid Rans-Les Turbulence Modeling Strategy For Cfd Simulation Of Gas Turbine Component Film Cooling, Cole Simmonds

Graduate Theses and Dissertations

Computational prediction of the flow physics associated with gas turbine film cooling is important for ensuring effective heat transfer design. These flow fields are highly turbulent and anisotropic, making the accuracy and efficiency of the chosen turbulence model an important aspect of performing high quality computational fluid dynamics (CFD) based analysis. Current industry standard Reynolds-averaged Navier-Stokes (RANS) turbulence models such as RANS k-ω SST, while computationally efficient, are subject to relatively high levels of uncertainty in their ability to predict these turbulent flow fields. In contrast, high fidelity methods such as Large Eddy Simulation (LES) are computationally very expensive, while …

Optimal Control Of Human Exercise Using An Individualized Physiological Three-Tank Model And Dynamic Programming, Asal Lotfi

All Theses

This thesis develops a physiologically inspired three-tank model of human bioenergetics to describe and optimize fatigue and recovery during exercise. The aerobic, phosphagen, and glycogen systems are modeled as coupled reservoirs whose states constrain instantaneous power output. Building on this representation, dynamic programming is used to compute pacing strategies that respect physiological limits while maximizing task-specific goals such as peak power or total work over a fixed duration, enabling individualized, goal-driven exercise prescriptions. The three-tank dynamics are formulated in continuous time and then discretized under a zero-order-hold assumption for simulation and optimal control. Model parameters are linked to standard field …

Reverse Design Of Solid Rocket Grain Geometry, Yechan Kang

Master's Theses

The reverse design of solid rocket motors remains a challenging process due to the nonlinear relationship between the grain geometry and the internal ballistics. The reverse design process involves obtaining an optimal grain geometry given a target performance curve set by mission requirements, which is the inverse problem of the forward design. The purpose of this study is to assess the validity and implementation of neural network and simulated annealing algorithms to perform the reverse design process. A modified phase field model of the eikonal equation is derived to simulate the evolution of combustion surfaces over time, enabling burn back …

Using Scenario-Based Design Activities To Explore Sociotechnical Thinking In Engineering Professionals, James M. Whealan

Master's Theses

Sociotechnical thinking is the ability to recognize the interconnectedness of both technical and non-technical dimensions such as environmental, economic, social, cultural, and political factors. Although traditional engineering curriculum often emphasizes technical knowledge and skills, research suggests that engineering work is inherently sociotechnical. While sociotechnical thinking is a critical engineering skill, relatively little is understood about the nature of it or the different aspects comprised within it. To that end, this study addresses the following research question: What sociotechnical factors do engineering professionals consider in a collaborative scenario-based design activity? To answer this question, we conducted a qualitative study of engineering …