Engineering Commons^™

Investigation Of Micronized Rubber Powder As An Alternative To Polymer Modifiers In Asphalt Pavement, Md Torikul Islam

Student Theses and Dissertations

Researchers have increasingly focused on polymer additives to enhance asphalt pavement performance. Crumb rubber (CR), derived from waste vehicle tires, has emerged as a potential modifier. This study investigates Micronized Rubber Powder (MRP), smaller than 75 μm, as an alternative to polymer modifiers. A PG 64-22 binder was modified with 5%, 10%, and 15% MRP (by weight), and the properties were compared with those of an SBS-modified PG 70-22 binder. Physical, mechanical, and chemical properties were assessed. The results indicated that MRP significantly increased viscosity and required higher processing temperatures. MRP-modified binders demonstrated improved rutting resistance, creep recovery, high-temperature performance, …

Designing A Hybrid Renewable Energy System For The College Of Engineering And Computer Science At Arkansas State University, Partho Das Neer

Student Theses and Dissertations

The main objective of this thesis is to design and analyze the performance of a hybrid renewable energy systems (HRES) for the college of engineering and computer science at Arkansas State University. By implementing the framework as a micro-grid to supply the required power to the Lab Science West building of the college. The proposed model ensures energy reliability and cost reduction. The model consists of photovoltaic (PV) panels, wind turbines (WT), and batteries, whereas MATLAB software was used to design the system and the Electrical Transient Analyzer Program (ETAP) Software is utilized to analyze the effectiveness of the operation …

09.22.2025 Ored Connect, Liz Williamson

ORED Newsletter

• Ralph E. Powe Junior Faculty Enhancement Award
• MIG Application Opportunity
• 10th Annual Advancing MS Conference

Designing For Shalom: Deepening Faith Integration In Engineering And Technology, Fred Haan

University Faculty Publications and Creative Works

Presented on 9/22/2025 at the event, Integration of Faith and Learning in the Disciplines at the University Pelita Harapan in Jakarta, Indonesia

Heat Transfer Enhancement In Cold Plate Heat Exchangers With Trapezoidal Vortex Generators, Montgomery Miller

Student Theses and Dissertations

An experimental investigation was carried out to study the effects of trapezoidal vortex generators (VGs) as a method of thermal enhancement within cold plate heat exchangers. Three different cold plates were imbedded with VGs in the bottom of the flow passage of varying sizes (h/H = 0.195, 0.253, 0.36) and quantity, as well as a cold plate with no VGs to be used as a comparative baseline. Testing was conducted under the laminar, transitional, and turbulent flow regime (Re = 1000 to 5500) using distilled water as the coolant. Experimental results indicate that the addition of VGs provide a positive …

Development Of An Instrumented Test System To Evaluate Mechanical Characteristics Of Belted Conveyor Systems, Coleman Emerson Wilson

Student Theses and Dissertations

The use of conveyor systems within industrial and warehouse settings gives the ability for increased productivity and increased speed of moving objects. As in many settings, the use of these conveyor systems requires large amounts of continuous runtime, and the ability to save even small amounts of energy over a large period can create large improvements in the total overhead cost of running the facility. Research into the ability to characterize the components within a conveyor system gives the ability to identify sources of large amounts of wasted energy and quantify these losses. There is a need to quantify the …

Comparative Analysis Of Belt-Slider Pan Configurations On The Power Consumption Of Belted Conveyor Systems, Asib Ridwan

Student Theses and Dissertations

Conveyor systems are widely used in industrial applications for material handling, but their high energy consumption remains a significant challenge. This study investigated the influence of different belt-slider pan configurations on conveyor power consumption, aiming to optimize efficiency while minimizing energy losses. Three types of slider pans; mild steel, galvanized steel, and powder-coated steel, were analyzed under controlled experimental conditions to determine the motor torque and power consumption of a test conveyor system under various loading conditions. Torque and power values were derived, plotted, and comparatively analyzed across all configurations to determine performance differences. Static friction coefficients of each type …

Global Transport Emissions 1850–2020: Historical Drivers And Lessons For Transport Decarbonization, Bernardo Tostes, Sofia T. Henriques, Matthew Kuperus Heun, Paul E. Brockway, Tânia Sousa

University Faculty Publications and Creative Works

This study analyzes global transport CO2 emissions from 1850 to 2020 using the LMDI method, offering, for the first time, a decomposition over such a long timespan and global scope. Emissions are split into technological and demand-related drivers using a new dataset. Transport efficiency is divided into final-to-useful efficiency and useful energy intensity, a novel distinction. Key findings include: (1) efficiency improvements avoided 9067 Gt CO2 by 2019, with peak impacts in 1950–1973 (-1.62 %/yr) and 2008–2020 (-3.63 %/yr), respectively; (2) these gains were insufficient to counter rising demand, which led to 8252 Gt CO2 in cumulative emissions; (3) demand …

Engineering And Technology, Fred Haan

University Faculty Publications and Creative Works

9/21/2025 for the event, Integration of Faith and Learning, at University Pelita Harapan in Jakarta, Indonesia

Comparative Study For Channel Pairing In Noma Ofdm- Cdma System, Hazem H. El-Banna, Nelly M. Shafik

Mansoura Engineering Journal

Orthogonal Multiple Access such as OFDM technique became inadequate scheme since it provides limited spectral efficiency and limited number of users. In addition to Orthogonal Multiple Access (OMA), Non-Orthogonal Multiple Access (NOMA) technique is applied in 5th generation of mobile communications that enhances both spectral efficiency and capacity with high Quality of Service (QoS). In this paper, three techniques were combined NOMA, OFDM, and CDMA in order to have optimal system performance in the presence of worst fading channel situations; fast frequency selective Rayleigh multi-path fading channel. The main contribution of this paper is the novel channel pairing technique introduced …

An Estimation Study Of The Co2 Emissions In Saudi Arabia Using Machine Learning, Mohammed A. Albalawi, M.M. El-Halwany, Mahmoud H. Mahmoud, Mohamed Gar Alalm

Mansoura Engineering Journal

As part of the 2015 Paris Climate Agreement, the Kingdom of Saudi Arabia (KSA) pledged to implement policies aimed at reducing greenhouse gas emissions. The 2030 Vision, which KSA unveiled with the goal of building a more sustainable and diverse economy, led to a number of projects, such as the national renewable energy program, the Saudi green initiative, and the circular carbon economy. Additionally, KSA just revealed a bold plan to achieve net-zero status by 2060. The Kingdom pledged to cut its carbon emissions by 278 million tons of CO2eq (equivalent) yearly by 2030 in its revised nationally determined contribution …

An Improved Method To Calculate Stripping Inflection Point (Sip) And Its Application In Evaluating Moisture Susceptibility Of Asphalt Mixtures, Ping Jiang, Bo Lin, Yizhuang David Wang, Jenny Liu, Seyed Alireza Ghanoon

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Accurately assessing asphalt mixtures' moisture susceptibility is critical because moisture damage can significantly reduce pavement durability, leading to premature failure and structural integrity of the pavement. The stripping inflection point (SIP), a moisture susceptibility index derived from the Hamburg Wheel Track (HWT) test, has practical merits in evaluating moisture susceptibility. However, current methods for determining the SIP showed low accuracy and high variability due to poor regression quality. Hence, this study aims to propose an improved method for calculating the SIP by modifying existing approaches to better capture the characteristics of rutting curves. Typical asphalt mixtures were used to conduct …

Analysis Of Modifications To An Outdoor Field-Scale Rotating Algal Biofilm Reactor With A Focus On Biomass Productivity And Power Usage, Davis R. Haag, Phillip E. Heck, Ronald C. Sims

Biological Engineering Student Research

Filtrate from dewatering anaerobically digested biosolids is a side-stream of wastewater treatment that contains high concentrations of nitrogen and phosphorus compounds that can serve as nutrients for cultivating microalgae biomass as biofilms for bioproduct production at Water Resource Recovery Facilities (WRRFs). One system used to cultivate attached microalgae biofilms is the rotating algal biofilm reactor (RABR). A pilot RABR with 72 m² growth surface area, 11.5 m² footprint area, and a liquid volume of 11,500 L was operated in an outdoor environment at the largest WRRF in Utah, U.S.A, the Central Valley Water Reclamation Facility (CVWRF). The configuration …

Figure Data For "Investigation Of A Stable And Saturated Reference Electrode Using Metal Chlorides And Oxides In Eutectic Licl-Kcl Molten Salts", Carlos Meija, Devin Rappleye

ScholarsArchive Data

This data set provide machine readable .csv files for the figures in the publication entitled "Investigation of a stable and saturated reference electrode using metal chlorides and oxides in eutectic LiCl-KCl molten salts" in Nuclear Engineering and Technology (Volume 58, Issue 1, January 2026, 103875).

An Event-Based Time-Incremented Snn Architecture Supporting Energy-Efficient Device Classification, David L. Weathers, Michael A. Temple, Brett J. Borghetti

Faculty Publications

Recent advances in Radio Frequency (RF)-based device classification have shown promise in enabling secure and efficient wireless communications. However, the energy efficiency and low-latency processing capabilities of neuromorphic computing have yet to be fully leveraged in this domain. This paper is a first step toward enabling an end-to-end neuromorphic system for RF device classification, specifically supporting development of a neuromorphic classifier that enforces temporal causality without requiring non-neuromorphic classifier pre-training. This Spiking Neural Network (SNN) classifier streamlines the development of an end-to-end neuromorphic device classification system, further expanding the energy efficiency gains of neuromorphic processing to the realm of RF …

Advanced Microstructured Batio3-Embedded Pvdf–Hfp/Peo Film For Enhanced Triboelectric Interface In Self-Sufficient Energy Generation And Sensing, Rigobert Ybarra, Diego De Leon, Michael Moreno, Cesar Sanchez, Fernando Viesca, Kevin Alejandro, Shishir Timilsena, Nicholas Dimakis, Joseph H. Dumont, Tommy Rockward, Tarik J. Dickens, Md. Wasikur Rahman, Mohammed Jasim Uddin

Mechanical Engineering Faculty Publications

The global reliance on fossil fuels and natural gas has largely dominated the energy production field, but due to finite resource depletion and escalating greenhouse gas emissions, the immediate exploration of sustainable energy alternatives to mitigate climate change and ensure resource security has been a major concern. There has been extensive research into other more renewable methods of energy production, such as wind and hydropower. Of these current energy generation types, there are many areas of untapped potential from the mechanical movements generated ambiently not only in the large scale of power generation but also on a smaller scale. The …

Unified Study Of The Classical Hall Effect, Carter J. Reed, Javier E. Hasbun, Wyatt E. Ackerman, L Ajith Desilva

Georgia Journal of Science

Germanium (Ge) samples with different doping types, acceptors (p-type) and donors (n-type), were studied to investigate charge carrier behavior. Carrier concentrations were found to be 1.16×10^21 m^(-3) for the p-type sample and 7.337×10^20 m^(-3) for the n-type sample. These experiments were conducted for the standard Hall effect (Hall voltage versus low magnetic field (B) values) as well as conductivity and Hall voltage versus temperature for different B-fields. The measurements versus temperature at zero-field allow us to obtain band gap ( Eg). While we investigate the conductivities for n-type and p-type doped samples, we also study the conductivity of an undoped …

Optimization Of Multi-Target Interception Scheme Based On Performance Simulation Modeling, Hanwen Liu, Zhimin Zhuo, Xue Yang

Journal of System Simulation

Abstract: The air attack scenarios faced by air defense weapons and equipment show the trend of saturation, diversification and intelligence. It is very important to establish multi-target interception efficiency model and optimize interception scheme according to simulation. The current intercepting efficiency index mainly considers the whole operation process, and can not guide the optimization of the intercepting scheme of specific intercepting rounds. The generation of interception schemes mainly relies on experience and simple mathematical model, which is difficult to cope with the increasingly complex and changeable battlefield environment. Therefore, an interception scheme advantage index that comprehensively considers interception probability and …

Design And Prediction Of Deep Fuzzy Neural Network, Chengbiao Wei, Taoyan Zhao, Jiangtao Cao, Ping Li

Journal of System Simulation

Abstract: A deep fuzzy neural network (DFNN) is proposed to solve the problem that the deep neural network has poor interpretability and the correction of the model is not targeted when dealing with the big data regression prediction problem. The proposed deep fuzzy neural network adopts an adaptive fuzzy Cmeans (AFCM) clustering algorithm in structural learning. The structure of the model, namely the number of rules and the antecedent parameters of the rules, is determined by calculating the introduced validity function. The identification of consequent parameters uses an improved grey wolf optimization (IGWO) algorithm. By replacing the linear decreasing strategy …

Kill Chain Efficiency Evaluation Model Based On Gray Dematel-Anp, Zejing Zhao, Junliang Shang, Yanpei Qin

Journal of System Simulation

Abstract: In modern conflict scenarios, the kill chain is integral to the comprehensive understanding, orchestration, and execution of military operations. Accurately appraising the efficiency of the kill chain is imperative for gaining insights into battle dynamics and strategically distributing military assets. However, traditional assessments of kill chain efficacy have been hampered by fragmented and isolated indicators that frequently overlook the interplay and influence among various segments of the kill chain. To address these limitations, based on the characteristics of each phase of the kill chain and the OODA loop theory, a new set of performance evaluation indices has been proposed. …

Optimization Method For Multi Agricultural Machinery Collaborative Operation Based On Genetic Algorithm And A* Algorithm, Yiran Yu, Huicheng Lai, Guxue Gao, Guo Zhang, Wangyinan Peng, Longfei Yang, Junhao Huang

Journal of System Simulation

Abstract: To address the uneven task distribution among multiple agricultural machines (referred to as farm machinery) and the high time cost due to numerous turning points at intersections, this paper proposes a task planning method that combines a pre-heat multi grouped genetic algorithm (PHMGA) with the turn A* algorithm (tA*). PHMGA allocates tasks to each piece of farm machinery based on the known environment, ensuring balanced workload through a cost objective function that considers travel, operation, and turning distances. It also designs various operators and strategies to search for nearoptimal solutions. The tA* algorithm is used to select paths …

Research On The Truth, Function And Common Principles Of Simulation, Haohua Xu, Bin Xiao, Yunhao Cui

Journal of System Simulation

Abstract: Simulation applications are becoming increasingly widespread and have a greater impact, while the theoretical foundation of simulation is relatively weak. This article provides a new definition of simulation by analyzing the common activities of simulation, which can include both virtual and real simulation forms; referring to Popper's three worlds theory, this paper discusses the objective authenticity of simulation from a philosophical perspective; From a methodological perspective, this paper elaborates on the methodological characteristics of simulation as an indirect cognitive object, revealing its significance in integrating human-machine intelligence and promoting knowledge evolution. It also discusses the common principles of simulation, …

A Model Combining Self-Attention And Weight Sharing For Human Activity Recognition, Lun Ma, Yue Yang, Daihe Wang, Guisheng Liao, Xing Li

Journal of System Simulation

Abstract: With the prevalence of wearable devices, human activity recognition based on wearable sensor data has garnered significant attention. The central issue in this field is how to extract effective behavioral information from raw sensor data to form corresponding feature vectors. Currently, convolutional neural networks and recurrent neural networks have been widely utilized for feature extraction from multisensory data. However, these networks struggle to globally capture the crucial temporal features inherent of human activity over time. To address this, a multi-CNN-BiLSTM-self attention (Multi-CBSA) model based on self-attention and weight sharing has been proposed, taking into consideration the logical correlations among …

Wingtip Docking Control Of Composite Aircraft Based On Adrc Theory, Chunlei Xie, Hongxia Hu, Weibo Han

Journal of System Simulation

Abstract: The process of wingtip docking in composite aircraft is challenged by significant unsteady vortex aerodynamic disturbances arising from the close-range coupling of wingtips, thereby posing considerable constraints on docking precision and flight safety. This study endeavors to address the intricate task of airborne wingtip docking control amidst wingtip vortex disturbances through a comprehensive investigation of airborne wingtip docking control technology, grounded in the tenets of active disturbance rejection control (ADRC) theory. Initially, a mathematical model encapsulating the dynamics of three-channel attitude/displacement during the docking operation, incorporating both the wingtip docking mechanism and the wingtip vortex model, is established. …

Solving The Vehicle Routing Problem Based On Deep Reinforcement Learning, Ming Jiang, Tao He

Journal of System Simulation

Abstract: The capacitated vehicle routing problem (CVRP) is a well-known combinatorial optimization challenge recognized as NP-hard due to its significant complexity. Building upon existing research, this paper introduces a novel end-to-end deep reinforcement learning approach based on a multi-pointer Transformer to tackle the CVRP. The proposed algorithm employs an invertible residual network in the encoder to encode input features, effectively reducing memory consumption. In the decoder, a multipointer network determines the probability distribution of solutions. To further enhance the performance of CVRP solutions, the algorithm leverages the symmetry in combinatorial optimization by implementing multi-trajectory parallel processing during both training …

Bioresources And Bioproducts: A New Open Access Journal, Ronald C. Sims

Biological Engineering Faculty Publications

Greetings to the bioresource and bioproducts community! I will serve as the Editor-in-Chief to collaborate with you as we promote the aims and scope of this new MDPI journal [1], with the help of its distinguished Editorial Board, by publishing Special Issues, Topics, Topical Collections, and Editorials, and by providing high-impact scholarship through the outstanding published work of each of our contributors.

Lane Detection In Dark Light Based On Instance Association, Yanji Jiang, Yingyang Zhang, Hao Dong, Xiaoguang Zhang, Meihui Wang

Journal of System Simulation

Abstract: In current research on lane detection, existing algorithms can efficiently detect lane lines under good lighting conditions. However, lane detection in low light still faces the challenge of a high false negative rate. A detection algorithm called Instance Association Net(IANet) is proposed to address this issue by utilizing the structural relationships between lane lines, which is helpful for low light conditions. The algorithm first generates unique masks for different lane lines using features at the starting points of the lane lines and a global feature map, achieving instance-level feature separation of the lane lines. It employs an instance-level attention …

Anylogic-Based Platform-Enterprise Collaborative Scheduling Simulation System For Cloud Manufacturing, Linxuan Wang, Yongkui Liu, Lin Zhang, Tingyu Lin, Lihui Wang

Journal of System Simulation

Abstract: Aiming at the lack of research on collaborative scheduling between a cloud manufacturing platform and associated enterprises, as well as the lack of simulation systems to simulate scheduling strategy combinations and to visualize dynamic scheduling processes, a simulation system that supports visualization of cloud manufacturing platform-enterprise collaborative dynamic scheduling processes is designed and developed. System requirements are analyzed in detail, and then a scalable platform-enterprise collaborative scheduling model and system functional architecture based on hierarchical multi-agents is proposed. Combined with a case of supply chain of industrial robots, considering random selection, time optimal strategy in the cloud manufacturing …

Digital Twin Modeling Method For Bulk Cargo Stacks Based On 2d Lidar, Houjun Lu, Yifei Zhu, Yanping Rong, Wanghui Zhang

Journal of System Simulation

Abstract: Due to the characteristics of large equipment, harsh working environment and time-varying shape of the material pile in bulk cargo terminal, there are some disadvantages such as low data accuracy and poor stability when building the storage yard model, which affects the unmanned and intelligent operation control. In this paper, we use two-dimensional laser radar combined with equipment mechanism motion to scan material pile point cloud data, present a digital twin modeling method for bulk storage yard, which includes static scene construction of storage yard and real-time modeling of material pile. Prefabricated models are used for the static scenes …

Digital Imaging Simulation Of Complex Scene Of Space-Based Space Small Target, Pengfei Li, Wei Xu, Yongjie Piao, Yinghong Fang, Dunpan Shi

Journal of System Simulation

Abstract: In response to the universal demand for space target detection technology research in space image data sources, this study focuses on the problems of insufficient training data for intelligent algorithms and the use of single data for traditional algorithms, with the goal of generating dynamic digital sequence images of small space targets in complex scenes. A visible light digital imaging simulation system based on a space observation platform is designed. A small target imaging model is proposed, which is based on two-dimensional shape feature point description and imaging analysis model to carry out digital modeling and imaging simulation of …