Engineering Commons^™

Experimental Investigation Of And Constitutive Model For The Thermo-Poro-Mechanical Deformation Of Granular Salt Under Hydrostatic Compression, Brandon C. Lampe

Civil Engineering ETDs

The influence of pore pressure and porosity on the ductile deformation of granular salt was experimentally investigated under hydrostatic compression. Confining and pore pressures were independently controlled while granular salt samples exhibited rate-dependent deformation that resulted in large decreases of sample volume and porosity. The sample deformation rates were observed to correspond with both the sample porosity and the pressure difference between the confining and pore pressures. Post-test observations revealed that the reduced porosity was caused by the solid particles deforming in a ductile manner. Insight into the cause of ductile deformation was gained by considering the local stress distribution …

2016 - Dwr Bulletin 118 Interim Update, California's Groundwater

Water Statutes

This interim update provides an up-to-date to information on groundwater basins subject to critical conditions of overdraft, groundwater basin boundaries, and basin prioritization, information essential to the successful implementation of SGMA (2014 Sustainable Groundwater Management Act), including the timely formation of groundwater sustainability agencies and the development of groundwater sustainability plans.

Task 10: Research An Alternative Instructional Design Model, Steven Hampton, Jan G. Neal, Luis A. Ramirez, Dustin R. Talkington, Jma Solutions, Inc.

Publications

Under authority of the Federal Aviation Administration (FAA), the Center of Excellence (COE) Technical Training Human Performance (TTHP) Task 10 research team has prepared a comprehensive technical report and an executive summary for the Air Traffic Organization (ATO) concerning the instructional development (ID) of occupational education and training for Air Traffic (AT) controllers and Technical Operations (TO) technicians. Research included:

• Front-end analysis of available FAA courses and government furnished information (GFI), including course-development documentation and associated guidance, policies, and regulations.

• Structured and semi-structured data-gathering techniques in cooperation with Instructional Systems Specialists (ISS), ISS Managers, and Requirements personnel.

• …

Evaluating Classifiers' Optimal Performances Over A Range Of Misclassification Costs By Using Cost-Sensitive Classification, Ramy Al-Saffar

LSU Master's Theses

We believe that using the classification accuracy is not enough to evaluate the performances of classification algorithms. It can be misleading due to overlooking an important element which is the cost if classification is inaccurate. Furthermore, the Receiver Operational Characteristic (ROC) is one of the most popular graphs used to evaluate classifiers performances. However, one of the biggest ROC’s shortcomings is the assumption of equal costs for all misclassified data. Therefore, our goal is to reduce the total cost of decision making by selecting the classifier that has the least total misclassification cost. Nevertheless, the exact misclassification cost is usually …

Definite Indefiniteness Of "Molecular Weight" As A Claim Term For Polymer-Related Patents, Ping-Hsun Chen

The Journal of Business, Entrepreneurship & the Law

The molecular weight of a polymer is not just a number for a single molecule. In fact, molecular weight measurement is based on a large volume of molecules of the same polymer. Due to the non-uniformity of molecular weights, there are several methods to measure an “average molecular weight” of a polymer. Unfortunately, the Federal Circuit in Teva Pharms. USA, Inc. v. Sandoz, Inc., 789 F.3d 1335 (Fed. Cir. 2015), held that the term “molecular weight” in several polymer claims was indefinite, because the term could mean either peak average molecular weight, number average molecular weight, or weight average molecular …

Modeling Of Nitihf Using Finite Difference Method, Nazanin Farjam, Reza Mehrabi, Haluk E. Karaca, Reza Mirzaeifar, Mohammad Elahinia

Mechanical Engineering Faculty Publications

NiTiHf is a high temperature and high strength shape memory alloy with transformation temperatures above 100oC. A constitutive model based on Gibbs free energy is developed to predict the behavior of this material. Two different irrecoverable strains including transformation induced plastic strain (TRIP) and viscoplastic strain (VP) are considered when using high temperature shape memory alloys (HTSMAs). The first one happens during transformation at high levels of stress and the second one is related to the creep which is rate-dependent. The developed model is implemented for NiTiHf under uniaxial loading. Finite difference method is utilized to solve the proposed equations. …

High Voltage Gain Dc/Dc Power Electronic Converters, Mehdi Ferdowsi, Venkata Anand Kishore Prabhala

Electrical and Computer Engineering Faculty Research & Creative Works

A DC/DC power converter provides high voltage gain using integrated boost and voltage multiplier (VM) stages. The boost cell operates according to a switching sequence to alternately energize and discharge a primary winding. A VM cell electrically coupled to the primary winding of the boost cell charges a multiplier capacitor to a DC output voltage greater than the input voltage when the primary winding is energized and discharges the multiplier capacitor when primary winding is discharged.

Power Transfer System, Hua Bai, Xuan Joe Zhou

Electrical & Computer Engineering Patents

A power transfer system and method are provided for transferring power from an AC supply outputting a first AC voltage. The system includes a controller and a matrix converter coupled to the AC supply for converting the first AC voltage to a second AC voltage. A primary coil is connected to the matrix converter and a secondary coil is in communication with the primary coil for producing an induced AC voltage. A secondary rectifier is connected to the secondary coil for rectifying the induced AC voltage to produce a secondary DC voltage. A sensor is coupled to the secondary rectifier …

Development Of A Novel Framework For The Application Of Signature Based Safeguards (Sbs) To Pyroprocessing, Philip Leo Lafreniere

Nuclear Engineering ETDs

Traditional nuclear material accountancy (NMA) faces several challenges when applied to pyroprocessing facilities. To address these challenges, alternative methods of safeguarding nuclear material are being developed. One method is process monitoring (PM). PM involves taking operational process data and applying it to safeguards using an advanced framework. Signature Based Safeguards (SBS), a proposed PM framework, involves the identification of anomalous scenarios and the subsequent identification and detection of their respective PM signatures from a system of measurements. SBS has previously focused on failure modes that result in transfer of mass to unexpected places in the mass flowsheet. This work developed …

Biobased Epoxy Asphalt Binder (Beab) For Pavement Asphalt Mixtures, Abdulrahman Fahad Al Fuhaid

USF Tampa Graduate Theses and Dissertations

In recent years, there have been significant concerns about environmental issues, sustainability of infrastructure, and depletion of nonrenewable resources for pavement construction. These concerns have led to substituting petroleum-based paving materials with their biobased counterparts. Research efforts have attempted to produce asphalt from renewable bio-resources. As a special modifier for asphalt, petroleum-based epoxy resin has been used in a few asphalt paving projects that require superior performance of asphalt mixtures. This study attempts to develop a biobased epoxy modifier for asphalt, which may improve asphalt performance at lower economic and environmental costs. Based on the findings from research in the …

High-Resolution Water Footprints Of Production Of The United States

Daugherty Water for Food Global Institute: Faculty Publications

The United States is the largest producer of goods and services in the world. Rainfall, surface water supplies, and groundwater aquifers represent a fundamental input to economic production. Despite the importance of water resources to economic activity, we do not have consistent information on water use for specific locations and economic sectors. A national, spatially detailed database of water use by sector would provide insight into U.S. utilization and dependence on water resources for economic production. To this end, we calculate the water footprint of over 500 food, energy, mining, services, and manufacturing industries and goods produced in the United …

Engineering Students Attend Concrete Bowling Ball Competition, Usu College Of Engineering

College of Engineering News

Four engineering students at Utah State University participated in the 2018 FRC Bowling Ball Competition in Salt Lake City, Utah.

Nasa Launches Usu Student-Built Experiment Into Space | College Of Engineering, Usu College Of Engineering

College of Engineering News

After long delays caused by storms and rough seas, NASA on Sunday launched a rocket into space carrying an experiment built by students at Utah State University.

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering: News & Publications (2013-2023)

• Honor Society Chapter Wins National Service Award

Magnetic Gradient Drilling, Garrett Lowry Nielsen

LSU Master's Theses

The drilling industry has always had difficulties with staying within the mud weight window. The problems associated with failure to stay within the mud weight window include uncontrolled influxes and wellbore collapse on the low pressure side of the window, and fluid losses and wellbore damage on the high pressure side of the window. When the risk for getting outside of this mud window becomes too great, casing must be set in order to isolate formations from each other. If too many strings of casing are set, or if the damage from getting out of the mud weight window is …

A Bayesian Network Based Adaptability Design Of Product Structures For Function Evolution, Shaobo Li, Yongming Wu, Yan-Xia Xu, Jie Hu, Jianjun Hu

Faculty Publications

Structure adaptability design is critical for function evolution in product families, in which many structural and functional design factors are intertwined together with manufacturing cost, customer satisfaction, and final market sales. How to achieve a delicate balance among all of these factors to maximize the market performance of the product is too complicated to address based on traditional domain experts’ knowledge or some ad hoc heuristics. Here, we propose a quantitative product evolution design model that is based on Bayesian networks to model the dynamic relationship between customer needs and product structure design. In our model, all of the structural …

Investigation Of Lstm Based Prediction For Dynamic Energy Management In Chip Multiprocessors, Milad Ghorbani Moghaddam, Wenkai Guan, Cristinel Ababei

Electrical and Computer Engineering Faculty Research and Publications

In this paper, we investigate the effectiveness of using long short-term memory (LSTM) instead of Kalman filtering to do prediction for the purpose of constructing dynamic energy management (DEM) algorithms in chip multi-processors (CMPs). Either of the two prediction methods is employed to estimate the workload in the next control period for each of the processor cores. These estimates are then used to select voltage-frequency (VF) pairs for each core of the CMP during the next control period as part of a dynamic voltage and frequency scaling (DVFS) technique. The objective of the DVFS technique is to reduce energy consumption …

A Novel Laser And Video-Based Displacement Transducer To Monitor Bridge Deflections, Miguel A. Vicente, Dorys C. Gonzalez, Jesus Minquez, Thomas Schumacher

Civil and Environmental Engineering Faculty Publications and Presentations

The measurement of static vertical deflections on bridges continues to be a first-level technological challenge. These data are of great interest, especially for the case of long-term bridge monitoring; in fact, they are perhaps more valuable than any other measurable parameter. This is because material degradation processes and changes of the mechanical properties of the structure due to aging (for example creep and shrinkage in concrete bridges) have a direct impact on the exhibited static vertical deflections. This paper introduces and evaluates an approach to monitor displacements and rotations of structures using a novel laser and video-based displacement transducer (LVBDT). …

Manufacturing Process Simulation – On Its Way To Industrial Application, Dennis Otten, Tobias A. Weber, Jan-Christoph Arent

International Journal of Aviation, Aeronautics, and Aerospace

Manufacturing process simulation (MPS) has become more and more important for aviation and the automobile industry. A highly competitive market requires the use of high performance metals and composite materials in combination with reduced manufacturing cost and time as well as a minimization of the time to market for a new product. However, the use of such materials is expensive and requires sophisticated manufacturing processes. An experience based process and tooling design followed by a lengthy trial-and-error optimization is just not contemporary anymore. Instead, a tooling design process aided by simulation is used more often. This paper provides an overview …

The Challenges Of Processing Kite Aerial Photography Imagery With Modern Photogrammetry Techniques, Jeremy W. Aber, Tyler A. Babb

International Journal of Aviation, Aeronautics, and Aerospace

Kite Aerial Photography (KAP) is a traditional method of collecting small-format aerial photography used for work in a variety of fields. This research explored techniques for processing KAP imagery with a focus on some of the challenges specific to photo processing. The performance of multiple automated image compositing programs was compared using a common set of 29 images. Those packages that were based on a photogrammetry approach outperformed the non-photogrammetric software, and generated similar levels of quality to one another. While all three photogrammetric packages produced satisfactory output, each had unique challenges.

Marketing Analysis Of Scholarly Journals In A Social World, Hunter Watson

Discovery Day - Prescott

The next methodology to the Airline Quality Rating (AQR) Social Media metrics is to determine if scholarly platforms for future use can benefit the AQR. The AQR authored by Dr. Brent Bowen and Dr. Dean Headley introduced the Airline Quality Rating (AQR) in 1993 as an objective method for comparing and scoring airline performance in areas deemed to be important for consumers. The quantitative metrics from utilizing new marketing techniques have increased the audience members attracted to this report. With a digitalized driven society, social media has been the main benefactor in gaining new attention. Continuing on the process to …

A Longitudinal Analysis On The Cyclical Pattern Of The Us Airline Industry, Michelle Bennett

Discovery Day - Prescott

The Airline Quality Rating (AQR) is the nation’s most comprehensive study of airline performance and quality for over two decades. The AQR sets the industry standard, providing consumers and industry watchers a way to compare performance quality among different US airlines using objective performance-based data (Bowen and Headley, 2014). The quantitative weighted average is computed monthly for every airline and divided by the sum of the weight to create the index. Criteria weighted in this formula include baggage handling, customer complaints, denied boarding and on time arrivals. This research employs the application of a longitudinal analysis methodology resulting in finding …

Functionalized Nanoporous Carbon Scaffolds For Hydrogen Storage Applications, Christopher Carr

Dissertations

Recent efforts have demonstrated confinement in porous scaffolds at the nanoscale can alter the hydrogen sorption properties of metal hydrides, though not to an extent feasible for use in onboard hydrogen storage applications, proposing the need for a method allowing further modifications. The work presented here explores how the functionalization of nanoporous carbon scaffold surfaces with heteroatoms can modify the hydrogen sorption properties of confined metal hydrides in relation to non-functionalized scaffolds (FS). Investigations of nanoconfined LiBH₄and NaAlH₄indicate functionalizing the carbon scaffold surface with nitrogen can shift the activation energy of hydrogen desorption in excess of …

Usability Assessment For Caregiver Behavior Analysis Using Gaming Technology, Alexandrea C. Oliver, Tanvi Banerjee, Jennifer Hughes, Noah L. Schroeder

Computer Science and Engineering Faculty Publications

The proposed research focuses on developing a mobile application for Android systems that will detect changes in behavior and activity patterns of those who are primary caregivers for dementia patients. This application will be used to detect fluctuation in the behavior and the task performance of the caregivers as a measure of caregiver stress. By detecting these changes in behavior, the goal is to analyze the effects of caregiving to evaluate caregiver burnout. A usability study was conducted for this application to find the optimal design factors and features that benefit the target user: the caregiver.

The purpose of this …

Dual Source Excitation Rectangular Waveguide Design And Evaluation For The Measurement Of Electromagnetic Material Properties, Daniel K. Koch

Theses and Dissertations

Broadband material parameter measurements are essential in understanding how materials interact with electromagnetic waves. Traditional rectangular waveguide material measurement systems are bandwidth limited. This results in multiple rectangular waveguides of different sizes used to conduct broadband material parameter extraction. Efforts to produce a broadband rectangular waveguide have focused on the inclusion of different guiding structures in the waveguide body. These designs have the drawback of requiring precise machining and time-consuming sample preparation. This research proposes a new broadband rectangular waveguide design which uses a dual source excitation design. This is enabled by the fact that rectangular waveguides are linear time …

Evaluation Of High Velocity Wear, Armando Deleon

Theses and Dissertations

The HHSTT located at Holloman Air Force Base conducts hypersonic testing in a unique way. Rather than perform cost prohibitive flight testing or hypersonic wind tunnel testing, a rocket-powered sled propels test articles down a track. This test setup has been used to test at speeds up to 2885 m/s (~Mach 8.6). The sled is kept on the rails by utilizing slippers, fabricated to wrap around the rail [1]. This slipper design keeps the sled from separating from the rail during a test due to the airflow producing lift, in a designed effort to minimize the wear that occurs during …

Effects Of Manufacturing Process Variables On Ultrasonic Testing In Electron Beam Melted Ti-6al-4v, Andrew D. Durkee

Theses and Dissertations

Further research on validating additive manufacturing production quality is required before the realization of direct print-to-fly application of critical components. This research examines the response of ultrasonic testing as a function of various manufacturing variables in electron beam melted samples of Ti-6Al-4V. Four dimensionally identical blocks with 6 spherical voids at varying depths were manufactured using different combinations of stock powder, edge treatments, and void melting. Scans were completed on two sides of each specimen with the transducer focused on the mid-plane. Additionally, one specimen was scanned 6 times, with the focal plane adjusted for each scan to match the …

Passive Load Testing For Evaluation Of Electromechanical Actuators, Jeremiah R. Hoffman

Theses and Dissertations

While aircraft control surfaces traditionally use hydraulic actuators, electromechanical actuators (EMAs) are interesting as they have potential to be lighter, lower maintenance, and more robust. However, EMAs require more research regarding force-fight characteristics, power requirements, performance specifications, and more. The Air Force Research Laboratory is conducting some of this research, and operates a test rig which provides a passive load to a pair of EMAs. This rig is designed for simple test profiles for investigating force-fight; if it could be used to represent actual flight profiles, the rig could accommodate a wider variety of tests. The focus of this project …

Design, Buildup, And Testing Of A Radial Rotating Detonation Engine For A Compact Auxiliary Power Unit, Riley Huff

Theses and Dissertations

Current power generators consume a large portion of the aircrafts usable volume and they are also extremely heavy for the amount of power that they can produce. Therefore, a need for compact, lightweight Auxiliary Power Units (APU) with high power density has arisen. A novel solution to this problem comes in the form of coupling a Rotating Detonation Engine (RDE) with a turbine generator. A new type of RDE referred to as the Radial Rotating Detonation Engine (RRDE) has been developed to fill this need. This project marks the first radial ow RDE successfully operated in the United States, and …

Creep Of Hafnium Diboride -20 Vol% Silicon Carbide At 1500°C In Air, Glen E. Pry

Theses and Dissertations

Refractory metal borides, commonly referred to as Ultra High Temperature Ceramics (UHTCs), exhibit a number of unique properties, such as extremely high melting temperature and hardness, chemical stability, high electrical and thermal conductivity and corrosion resistance. It has been demonstrated that the addition of SiC improves the oxidation resistance of ZrB2- and HfB2-based UHTCs above 1200°C by modifying the composition of the oxide scale. Addition of SiC retards the oxidation rate of ZrB2 and HfB2 by forming a protective layer of borosilicate glass. Creep deformation is one of the critical criterion for structural application of ceramics at elevated temperatures. Compression …