Engineering Commons^™

Case Study: Expectation And Perspective In The Punch List Process, Carlye L. Cunningham

Construction Management

The punch list process is a crucial phase of construction that is performed on every project. The punch list is a document generated near the end of the project that includes unfinished items and/or work that is not conforming to specifications or expectations. It requires immense coordination and communication between the owner, general contractor, and subcontractors in order for it to be executed efficiently. How the punch list is performed can be very instrumental or detrimental as all parties work together to close out the project. This paper will examine the punch list procedures that took place during the closeout …

Legal Issues And Feasibility Of Construction Under Railroad Tracks At Cedar Creek Apartments, Brendan Donovan

Construction Management

This paper describes the impediments of initiating construction of a local tunnel underneath the railroad tracks approximately 50 yards South-West of the Foothill Blvd and California Blvd intersection. This tunnel is used by hundreds of students every day and acts as the primary route for these students to get to and from the Cal Poly campus. This tunnel has no lighting, is constantly flooded with water, and has multiple safety hazards. The author discusses the feasibility of starting construction to make this pathway a safe accessible route for all students. Throughout the paper, the author introduces the multiple parties with …

Community Service Project For Senior Citizen, Adam J. Bloomer

Construction Management

This community service project for a local senior citizen consisted of a complete construction package including: obtaining funding, purchasing necessary materials, schedule planning, design, development and construction of a mid-sized concrete staircase. Using the knowledge and prior practices I acquired while studying Construction Management at California Polytechnic University San Luis Obispo I was able to fulfill every aspect the client had requested. This staircase not only served as an easier walkway into the backyard of the home but also as a stormwater accessway allowing for minimal puddle and mud accumulation outside the clients front door. The projects material cost of …

Case Study: Proven Benefits Of Insurance Backed Stretch And Flex Programs With Cdm Smith, Colin Dzubnar

Construction Management

Safety is the most important aspect of the construction industry. Due to daily strenuous physical activities that occur on a construction jobsite, having your body warmed up, pain-free and ready to perform labor intensive tasks is critical. This case study will examine the correlation between the past and present daily stretching format at the construction jobsite with CDM Smith and Insurance Company. For continuity, it will include an interview with the same CDM Smith Region H&S Manager as well as similar surveys to find out the construction workers thoughts and reactions to stretching prior to work. Although IO to 20 …

A Case Study Of The Construction Labor Market And Impact Of Retiring Baby Boom Generation, Grant Bettisworth

Construction Management

Construction firms often analyze the impacts of schedule, cost, and quality when reviewing the risk associated with a project. An important aspect of the project execution effort; available skilled labor resources, can have a significant impact on the success of the project but may not always be considered as part of the risk analysis effort. The intent of this paper is to discuss the contribution of the baby boom generation, how the retirement of baby boomers will impact the labor market, what this means for the construction industry and how construction firms can mitigate risks associated with this phenomenon. Since …

Case Study: Analyzing The Benefits Of Using 3d Printing On The Mexican Museum Renovation Project In San Francisco, California, Benjamin Jodis

Construction Management

The use of three-dimensional (3D) printing is not yet prevalent throughout the construction industry. Although there have been some uses, each has been small and relatively experimental, however, a current renovation project to the Mexican Museum in downtown San Francisco utilized 3D printing to aid in design coordination. The decision came after the General Contractor, Webcor Builders, noticed a possible constraint in pouring a section of the foundation; a pair of nine-foot vertical concrete walls surrounding the elevator shaft. The walls posed a serious threat to the schedule and budget of the project, raising concerns with shoring, waterproofing, and constructability. …

Ferroresonance In The High Voltage Powerline Industry, Joe Granger

Construction Management

Ferroresonance is an issue often overlooked in the high voltage powerline industry. Ferroresonance is a complex nonlinear electrical phenomenon that can cause dielectric and thermal problems to transformers. It is a very complex topic that is not completely understood and requires a large amount of work in order to comprehend. It can cause injury to Lineman that work around it and damage equipment. The proper training and a safety device could make the industry safer and save money. Through interviews and research I have studied the need for a safety device that applies load to a transformer during installation in …

Implementation Of Industry Technology Into The Construction Management Department, Kristen D. Forster

Construction Management

With technology being one of the fastest growing items in the construction industry it is important to keep on top of what is utilized most commonly. To fully prepare graduates for the work force, the Construction Management Department at Cal Poly, San Luis Obispo needs to focus efforts on supplying students with the most commonly used industry technologies. Utilizing these programs in the current curriculum will ensure that graduates from the Construction Management Department are prepared to take on the work force with the most relevant software under their belts. Students who understand how to use these industry sanctioned technologies …

Completion Of Hope's Village Tiny Homes, Jimmy P. Fewell

Construction Management

In Fall, 2018 the Cal Poly Construction Management Department teamed up with the non-profit, Hope’s Village, to create two tiny homes that are to be used for homeless shelters. The Residential Construction class built the structures, and I finish the siding for this plan. In finishing the siding I was incharge of the designing, planning and execution of the project.

Investigation Of Cardiovascular Tissue Following 56fe-Radiation And Potential Countermeasure Effectiveness., Alexandra R Decarlo

Electronic Theses and Dissertations

Exposure to ionizing radiation is an important medical concern because it can lead to health problems including cancer and cardiovascular issues. In space, astronauts are exposed to ionizing radiation that is not experienced by those who remain on Earth. This radiation can cause health problems such as cardiovascular disease. One way this can happen is through the creation of reactive oxygen species, which can activate TGF-β1, contributing to fibrosis or other cardiovascular problems. Antioxidants can be a potential pharmacological mitigator of these excess reactive oxygen species because of their ability to neutralize reactive oxygen species. One such antioxidant with potential …

Plga-Modified Nanoparticles For The Treatment Of Hypo-Vascularized Hpv-Related Cervical Cancers., Lee B. Sims

Electronic Theses and Dissertations

A major challenge associated with delivery of active agents in the female reproductive tract (FRT) is the ability of agents to efficiently diffuse through the cervicovaginal mucosa (CVM) and reach the underlying sub-epithelial immune cell layer and vasculature. A variety of drug delivery vehicles have been employed to improve the delivery of agents across the CVM and offer the capability to increase the longevity and retention of active agents to treat infections of the female reproductive tract. Nanoparticles (NPs) have been shown to improve retention, diffusion, and cell-specific targeting via specific surface modifications, relative to other delivery platforms. In particular, …

Phase Unwrapping Of 4d-Flow Mri Data With Graph Cuts., Andrew Justice

Electronic Theses and Dissertations

A common issue when measuring velocity utilizing 4D flow magnetic resonance imaging (MRI) is aliasing that occurs because of a low velocity encoding parameter (VENC). Aliasing can be avoided if the velocity encoding parameter is set above the largest velocity quantity. However, when this is done the velocity to noise ratio is lowered less detail is acquired in the image. Thusly, it is sometimes desirable to have a below the maximum velocity to acquire higher quality data.

Consequently, an efficient and robust algorithm is needed to unwrap the aliased data. This paper proposes an iterative graph cuts algorithm to perform …

Addition Of Exothermic Reaction Scale-Up Lab To Unit Operations Curriculum., Lisa A Anderson

Electronic Theses and Dissertations

According to the Chemical Safety Board’s 2002 report entitled "Improving Reactive Hazard Management,” the CSB identified 167 serious accidents involving uncontrolled chemical reactions in the United States between 1980 and 2001 causing 108 deaths and hundreds of millions of dollars in property damage. Of the 167 accidents, 35% involved runaway reactions. One noteworthy incident from recent history is the fatal explosion that occurred at T2 Laboratories in Jacksonville, FL as a result of improper scale-up and an insufficient cooling design for the system.

One recommendation resulting from the CSB investigation of the incident was that the Accreditation Board for Engineering …

A Novel Design For A Silicon And Cadmium Telluride Tandem Solar Cell., Jacob A Vittitow

Electronic Theses and Dissertations

No abstract provided.

Reactive Lamination Of Perovskite Solar Cells., Lyndie Burns

Electronic Theses and Dissertations

Due to the growing demand for energy internationally and the environmental impact of other conventional energy technologies, solar power has been a growing area in the energy landscape. Perovskite research has increased substantially because of the high power conversion efficiencies, up to 22%, with many recent advances in the use of these organic-inorganic hybrid perovskites for photovoltaic cells. However, to bring perovskite solar cells into the industrial world, the overall cost of the manufacturing of the solar cell must be improved to compete with other well-developed photovoltaic technologies. Here is presented an alternative perovskite deposition method for methylammonium lead halide …

Investigating The Likelihood Of Pediatric Femur Fracture Due To Falls Through Finite Element Analysis., Keyonna Mckinsey

Electronic Theses and Dissertations

Bone fracture is the second most common injury of child abuse. Studies have generally reported that femur fractures are more likely due to abuse than accidental causes in cases where the child is non-ambulatory. They have also found that household falls are commonly offered as the cause of injury in cases of abuse. In this study, a finite element (FE) pediatric femur model will be developed and used to evaluate likelihood of fracture in common household fall scenarios (bed falls and feet first falls). This will provide greater biomechanical evidence as to the likelihood of femur fracture due to common …

Enhancing Performance Of Ionic Liquid Property Prediction With Molecular Dynamics., Trisha H. Patel

Electronic Theses and Dissertations

Molecular dynamics have been used to predict thermodynamic and transport properties of eight room-temperature ionic liquids. Simulation parameters including box size and van der Waals cutoffs were varied. The density, heat capacity, and self-diffusion coefficients of the ionic liquids were computed and compared to experimental data and to previously published simulations. Predicted properties were generally close to their experimentally observed values. It was determined that the prediction of ionic liquid properties via molecular dynamics simulations could be accelerated several-fold by using less stringent integration parameters and smaller simulation sizes. The properties of density and heat capacity did not change significantly …

Comparing Stenotic Blood Flow In Three- And Two-Dimensional Arterial Renderings Using Computational Fluid Dynamics And Multiphase Mean Age Theory., Jacob S. Garza

Electronic Theses and Dissertations

Over one million invasive coronary angiography procedures are performed annually in patients who experience chest pain or are known to have coronary artery disease. The procedure is carried out to ascertain the degree of arterial blockage (stenosis) that hinders blood flow to the heart. A cardiologist performing the procedure determines the physiological degree of a stenosis by either visual estimation, which is routine practice, or by invasively measuring fractional flow reserve (FFR), which is the current gold standard that has been demonstrated to improve patient outcomes and temper the cost of healthcare. Nevertheless, FFR is performed in only 10–20% of …

Software Defined Radio For Cubesat Communication, Sarah Watkins

Undergraduate Honors Capstone Projects

Cube satellites, more commonly referred to as CubeSats, are small satellites that have become increasingly popular for academic, amateur, commercial, and scientific applications over the past five to ten years. These satellites provide a fairly inexpensive and compact platform for deploying many different types of equipment. While CubeSats do not allow for housing large, complex instruments, some organizations have begun to explore the possibility of deploying networks, or clusters, of CubeSats. Satellites in these clusters could theoretically be tied together via radio frequency communications to accomplish more than a single CubeSat could alone.

This report summarizes the preliminary design and …

Hscr: High Speed Cubesat Radio, Colton Lindstrom

Undergraduate Honors Capstone Projects

Software Defined Radios (SOR) are limited by their usable bandwidth, which restricts how quickly they can transmit or receive data. The High Speed Cubesat Radio (HSCR) is capable of transmitting and receiving higher bandwidth signals by combining the bandwidths of several individual SOR transceivers. The HSCR performs phase correction to seamlessly stitch the bandwidths of each individual SOR into a single larger bandwidth.

By increasing the number of SDRs inside the HSCR, the bandwidth of the overall system will increase. This increase in bandwidth is limited only by the speed of the processing unit in working with received or transmitting …

Assisted Switched Reluctance Machines, Amy Robinson

Honors Scholar Theses

Switched reluctance machine (SRM) modifications in both control schemes and physical design have been steadily increasing in academia to improve machine performance. Assisted switched reluctance machines (ASRMs) are a type of design modification for SRMs. Permanent magnets (PMs) and electromagnetic DC coils (DCC) are being added to the SRM to improve its torque output and overall efficiency. The choice for the design modification has been evolving throughout the decades. The focus has shifted from adding DCC to ASRM to adding PMs to ASRMs. This paper reviews the research trends of ASRMs and includes an analysis of the modified stator yoke …

Effect Of Silk-Based Hydrogel Topography On Intestinal Epithelial Cell Morphology And Wound Healing In Vitro, Marisa E. Boch

Honors Scholar Theses

Recent advances in the field of biomaterials have suggested that cells cultured on substrates resembling the native tissue mechanical properties, matrix and growth factor composition, and topography can adopt phenotypes that more closely resemble the in vivo tissue compared to cells cultured on non-mimetic constructs. Understanding the effect of culture substrate on in vitro tissue formation is important for bioengineering applications that include mechanistic studies of healthy tissue function and development of disease models. In this work, Caco-2 adenocarcinoma cells were seeded on flat and crypt-like topographies of 3D-printed cytocompatible hydrogels derived from silk fibroin protein. Silk hydrogels were selected …

Antimicrobial Materials Via Thiol-Ene Chemistry, Dahlia Amato

Dissertations

With the increasing prevalence of antimicrobial resistance, the escalation of opportunistic/pathogenic infections is a looming global crisis. To avoid the pitfalls of conventional antibiotics, this dissertation focuses on developing macromolecular solutions to develop novel antimicrobial materials based on essential oils (thymol, carvacrol, and aldehydes). It is well established that essential oil derivatives exhibit high potency towards a wide range of pathogenic microbes. The rapid photopolymerization kinetics, limited by-products, and homogeneous network formation afforded by thiol-ene photopolymerization are utilized to either encapsulate essential oil derivatives or convert them into monomers which can subsequently be incorporated into new antimicrobial materials with new …

Polymer Nanocomposites Containing High Aspect Ratio Particulates: Innovation In Co-Extruded Multilayer Barrier Films, Kevin Meyers

Dissertations

Delaminated montmorillonite (MMT) clay/ maleic anhydride grafted LLDPE nanocomposite multilayer films with alternating layers of LDPE were produced through multilayer co-extrusion. The MMT concentration within the nanocomposite layers was increased through annealing the films in the melt due to a mismatch in interdiffusion rates of the polymer layers. Analysis of the nanocomposite layers upon annealing revealed that the platelets impinged upon one another resulting in significant improvement in oxygen barrier in the multilayer system, exceeding the results of bulk nanocomposites.

Model analysis demonstrated that increasing the nanoplatelet aspect ratio or initial concentration in the filled layers would lead to even …

An Underwater Vehicle Navigation System Using Acoustic And Inertial Sensors, Khalid M. Alzahrani

Doctoral Dissertations and Master's Theses

Unmanned Underwater Vehicles (UUVs) have become an essential tool for different underwater tasks. Compared with other unmanned systems, the navigation and localization for UUVs are particularly challenging due to the unavailability of Global Positioning System (GPS) signals underwater and the complexity of the unstable environment. Alternative methods such as acoustic positioning systems, Inertial Navigation Systems (INS), and the geophysical navigation approach are used for UUV navigation. Acoustic positioning systems utilize the characteristics of acoustic signals that have a lower absorption rate and a more extended propagation distance than electromagnetic signals underwater. The significant disadvantage of the INS is the “drift,” …

Numerical Simulation Of Shock Wave Propagation In Ducts With Grooves, Seyed Mehdi Mortazawy

Doctoral Dissertations and Master's Theses

The pressure attenuation of moving shocks when they propagate in ducts, is of great importance in a wide variety of applications, such as health, safety, and transportation. The objective of this research is to simulate the propagation of shock waves in ducts with roughness. The roughness is added in the form of grooves as in an existing experiment. Different shapes are considered in order to better understand the physics behind the evolution of the complex shock patterns resulting from diffraction, reflection and refraction of the primary moving shock. The contribution of grooves and duct shape on these phenomena and pressure …

Arm Position Measurement, Silvia Smith

Undergraduate Honors Capstone Projects

This capstone project addresses the design and implementation of a device that measures arm position and speed. The device is intended for use in conducting further research on the motion of limbs affected by cerebral palsy, and in the prototypic development of a device that could help control such motion, thereby allowing a user to accomplish daily tasks. This project includes the design of an appropriate experiment and testing apparatus to explore possible solution prototypes, along with suggested methods to perform analysis of the experiment results. This is considered to be the fundamental research necessary to better understand the scope …

Designing A Synthetic Spider Silk-Based Coating For Urinary Catheters To Reduce The Risk Of Cautis, Alexander Cook

Undergraduate Honors Capstone Projects

Urinary and Intravenous (IV) catheters are two of the most commonly used medical devices for administering vital drugs and obtaining diagnostic samples from patients. Unfortunately, hospital acquired infections (HAIs) occur at alarming rates due to catheter usage. The aim of this project was to design a urinary catheter that would decrease the occurrence of these infections with a catheter coating that utilizes the antimicrobial properties of synthetic spider silk in combination with the antiseptic chlorhexidine. This synthetic spider silk catheter will introduce a novel approach to catheterization in the medical industry.

Rickshaw For Common Ground, Marcus Dallin Cronin

Undergraduate Honors Capstone Projects

For this project my team and I were asked to design and manufacture a rickshaw, a device which will enable disabled individuals to experience outdoor hiking trails, for a non-profit organization based in Logan, Utah called Common Ground. Common Ground specializes in helping people with disabilities experience the outdoors in ways that would otherwise be impossible. The rickshaw will help Common Ground achieve its goals by providing them with a way to transport people with disabilities on moderately difficult hiking trails (i.e. Wind Caves Trail in Logan Canyon). In the past, Common Ground had use of a rickshaw that had …

Buffer Controlled Cache For Low Power Multicore Processors, Marven Calagos

Theses and Dissertations

This thesis proposes a buffered dual access mode cache to reduce power consumption in multicore caches for embedded systems. This cache is called Buffer Controlled Cache (BCC cache). The proposed scheme introduces a pre-cache buffer to determine how to access the cache. The proposed cache shows better prediction rates and lower power consumption than conventional caches, such as Phased cache and Way-prediction cache. For single core implementation, Simplescalar and Cacti simulators have been used for these simulations using SPEC2000 benchmark programs. The experimental results show that the proposed cache improves the power consumption by 37%-42% over the conventional caches. Multi2Sim …