Engineering Commons^™

Knowledge Reuse Through Electronic Knowledge Repositories: An Empirical Study And Ontological Improvement Effort For The Manufacturing Industry, Peter Panha Chhim

Wayne State University Dissertations

Knowledge management adoption is growing, and will continue to grow in no small part because of its recent inclusion into the ISO 9001 quality standard. As organizations look towards ways in which to manage their knowledge, the codification of explicit knowledge through Knowledge Management Systems (KMS) and Electronic Knowledge Repositories (EKRs) will undoubtedly gain more interest.

An EKR is a form of KMS that emphasizes the codification and storage of organizational expertise for the purposes of Knowledge Reuse (KRU). Unfortunately, the factors surrounding KRU are not well understood. While previous studies have viewed EKR usage from a narrow perspective, a …

Eliminating Electromechanical Instability In Dielectric Elastomers By Employing Pre-Stretch, Liang Jiang, Tony Betts, David Kennedy, Stephen Jerrams

Articles

Electromechanical instability (EMI) is one of most common failure modes for dielectric elastomers (DEs). It has been reported that pre-stretching a DE sample can suppress EMI due to strain stiffening taking place for larger strains and a higher elastic modulus are achieved at high stretch ratios when a voltage is applied to the material. In this work, the influence of equi-biaxial stretch on DE secant modulus was studied using VHB 4910 and silicone rubber (SR) composites containing barium titanate (BaTiO3, BT) particles and also dopamine coated BT (DP-BT) particles. The investigation of equi-biaxial deformation and EMI failure for VHB 4910 …

Drivers Of Food Wastage And Their Implications For Sustainable Policy Development, Krista L. Thyberg, David J. Tonjes

Technology & Society Faculty Publications

There has been growing interest in establishing food waste prevention and recovery programs throughout the world. The drive to target food waste stems from increasing concerns about resource conservation, food security, food waste’s environmental and economic costs, and a general trend in the waste management industry to transition to more sustainable practices. Here the drivers of residential, institutional, and commercial food waste generation in developed countries, particularly in the U.S., are explored. The impacts of food system modernization on food waste generation are examined, particularly impacts related to food system industrialization, urbanization, globalization, and economic growth. Socio-demographic, cultural, political, and …

Electromagnetic Analysis Of Different Geometry Of Transmitting Coils For Wireless Power Transmission Applications, Mohammad Haerinia, Ali Mosallanejad, Ebrahim S. Afjei

Electrical Engineering Student Publications

No abstract provided.

The Revised Certified Technology Manager Exam: The First Year's Results, Mark Doggett, Farshid Alavi

SEAS Faculty Publications

The objective of this study was to evaluate the performance of the revised Certified Technology Manager (CTM) exam after implementation in order to determine if it is meeting expectations and if further revision is needed. In addition, this study provided a methodology framework for evaluating other similar exams both now and in the future. Three groups benefit from this research. Test-takers can have a fair evaluation of their performance. Test-designers can use the results of the study to improve their question design skills for other exams or revisions to the current CTM exam. The Association of Technology, Management, and Applied …

Perceptions Of The Advanced Manufacturing Competency Model (Amcm) For Curriculum Development, Mark Doggett, Muhammad Jahan

SEAS Faculty Publications

The Advanced Manufacturing Competency Model (AMCM) model emphasizes building of competencies at all levels ranging from the shop floor production worker to manufacturing engineers. It consists of different levels of competencies organized hierarchically. The levels are personal effectiveness, academic, workplace, industry-wide technical, industry-sector technical, management and organization-specific competencies.

This paper discusses survey research on the perceptions of manufacturing students, faculty, and industry advisory board members regarding the AMCM. The research evaluated the manufacturing program based on perceptions of the AMCM competencies and the curricular coverage required for entry-level manufacturing professionals. Specifically, the survey sought to answer the following research questions: …

Analysis Of The Developing States In The Mena Region Seeking Civilian Nuclear Energy, With A Primary Focus On The Kingdom Of Saudi Arabia (Ksa) And The United Arab Emirates (Uae), Thaqal Alhuzaymi, Ayodeji Babatunde Alajo

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

The comprehensive analysis presented here attempts to ana­lyze “newcomer” states in the Middle East and North Africa (MENA), primarily the Kingdom of Saudi Arabia (KSA) and Unit­ed Arab Emirates (UAE), seeking to implement civilian nuclear energy according to their political and economic situations. By investigating their motivations and funding resources for fu­ture nuclear projects, this analysis provides guidance for these states in terms of their nuclear infrastructure and nonprolifera­tion. The overall approach of this analysis relies on the factors for the success of civilian nuclear energy programs identified in experiential studies conducted since the Atoms for Peace speech in 1953.This …

Reviews And Syntheses: Ocean Acidification And Its Potential Impacts On Marine Ecosystems, Khan M.G. Mostofa, Cong-Qiang Liu, Weidong Zhai, Marco Minella, David Vione, Kunshan Gao, Daisuke Minakata, Et.Al

Department of Civil, Environmental, and Geospatial Engineering Publications

Ocean acidification, a complex phenomenon that lowers seawater pH, is the net outcome of several contributions. They include the dissolution of increasing atmospheric CO2 that adds up with dissolved inorganic carbon (dissolved CO2, H2CO3, HCO3−, and CO32−) generated upon mineralization of primary producers (PP) and dissolved organic matter (DOM). The aquatic processes leading to inorganic carbon are substantially affected by increased DOM and nutrients via terrestrial runoff, acidic rainfall, increased PP and algal blooms, nitrification, denitrification, sulfate reduction, global warming (GW), and by atmospheric CO2 itself through enhanced photosynthesis. They are consecutively associated with enhanced ocean acidification, hypoxia in acidified …

Experimental Study Of The Flow Of Ferrofluid In A Porous Media Under A Magnetic Field, Muskaan Khurana

Dissertations, Master's Theses and Master's Reports

This research presents results from a laboratory-scale experimental setup that was designed to visualize the behavior of ferrofluid percolation through a porous media. Ferrofluids are colloidal suspensions made of magnetic particles of a few nanometers and stabilized in carrier liquids like water or mineral oil. Ferrofluids get magnetized and align themselves in the direction of a magnetic field when a field gradient is applied.

With the help of this experiment we investigate the viability of controlling fluid flow in porous medium by a magnetic field in vicinity. The experiments show that ferrofluids can be used as a transporting media to …

A Comprehensive Methodology For Design Of A Circulation Control Small-Scale Unmanned Aircraft, Konstantinos Kanistras

Electronic Theses and Dissertations

Unmanned Aerial Vehicles (UAVs) have become increasingly prevalent and important for a wide spectrum of civilian and military operations. When focusing on small-scale fixed-wing UAVs, payload, power and energy requirements limit considerably their utilization and flexibility allowing them to complete only those specific missions they are designed for. Circulation Control (CC) is an active flow control method used to produce increased lift over the traditional systems (flaps, slats, etc...) currently in use. This dissertation focuses on the foundations of a comprehensive methodology from design to implementation and experimental testing of Coanda-based Circulation Control Wings (CCW) for unmanned aircraft. The …

Python Examples For Multiobjective Data Visualization, J. Herman

All ECSTATIC Materials

Example data file and code to plot N-dimensional scatter plot, parallel axis plot, and a matrix of 2-dimensional scatter plots.

Arakniprint: 3d Printing Of Synthetic Spider Silk To Produce Biocompatible And Resorbable Biomaterials, Ashley Ruben, Brianne Bell, Chase Spencer, Craig Soelberg, Dan Gil, Thomas Harris, Richard Decker, Timothy A. Taylor, Randolph V. Lewis

UCUR

No abstract provided.

Catheter Attachment Device For Prevention Of Urinary Tract Infection, Ashleigh Mccormick, Brittany Allen, Karolina Stumbraite, Kevin Ball

Capstone Design Expo Posters

Hospital-acquired infections are costly occurrences that cause patients physical discomfort, have dangerous immune consequences, and cost healthcare providers hundreds of millions of dollars every year in liability fees and negligence charges. Catheter associated urinary tract infections (CAUTI) are the most common class of hospital-acquired infection, affecting over half a million patients in U.S. hospitals alone every year.The CAUTI-Guard team has designed a silver-coated polydimethylsiloxane (PDMS) plug device that helps prevent CAUTI through its action as a physical and chemical block. The device slides along standard urinary catheters and helps block the migration of infectious material into the urethra and subsequently …

Small Animal Thermal Support Device: Thermoregulation System For Scireq Flexivent Chamber, Alexander Dickey, Ashkhan Hojati, Matthew James, Kathleen Vermillera

Capstone Design Expo Posters

During ventilation induced lung injury (VILI) experiments, anesthetized mice lose the ability to regulate their core body temperature. Without maintaining homeostasis, the experimental data may be compromised due to changes in the rodent’s internal functions. Traditional heating techniques utilize a water circulation heating system that is unable to fit inside flexiVent ventilator testing chambers. The objective of this project is to design and build an automatic thermoregulatory feedback system to regulate the core body temperature of a mouse inside individual testing chambers throughout the duration of the experiment. The project deliverables include a functioning prototype that achieves safe and effective …

Tatami: A Productive Work-Based Social Media, Jacob Kreiner, Jacob Holcombe, Minh Nguyen

Capstone Design Expo Posters

Tatami is a collaborative social media app created by Ippon Technologies that focuses on workflow and communication in an industry setting. Ippon wanted a product that allows members of a company to maximize productivity, and have a communal message board that shows what is going on in the company currently. Functionality of this product would allow a user to create an account, set up and edit their profile and be able to post messages to a workplace timeline. For a more specific and personal timeline we need users to be able to create and subscribe to groups and trends corresponding …

Gnu Radio Companion (Grc) On Software Defined Radio Platforms, Jacob Ramey, James Begemann, Richard Hite

Capstone Design Expo Posters

Software defined radio (SDR) is a method to design radio frequency (RF) signal systems using software to implement radio components that are normally implemented in hardware. Several examples of components that can be designed in SDR include RF signal filters, signal amplifiers, and signal resamplers. SDR applications include amateur radio transmission, aircraft and ship tracking, RF communications, and radio astronomy, to name a few. A great advantage of implementing a RF system in software is that the system developed in software is more flexible and upgradeable than a system designed with hardware alone.

QRC Technologies offers a wide range of …

Kinectvision360: A Real-Time Human Tracking System, Robert Ha, Ravideep Marwaha, Joseph Crouch

Capstone Design Expo Posters

KinectVision360 project integrates multiple Microsoft Kinect sensors to investigate the capabilities of the low cost human interactive device to apply them to modern problems in comparison to high cost devices. The project includes human face/skeletal tracking and a larger field of vision. We incorporate three Kinects (1st generation) and a custom computer with components necessary to process large amounts of data in real-time. Figure 1 represents an overview of the processes the program follows in order to execute and visualize the data for tracking. The “FaceTracking” class contains algorithms and logic to retrieve skeletal information from infrared depth sensors in …

Sustainability: Reusing Data Center Waste Heat, John Boushra, Kyle Duncan, Aleksandr Kogan, Giang Pham

Capstone Design Expo Posters

Data Centers are facilities used to house a large number of computer systems and their associated components, such as telecommunications and data storage systems. Nowadays many organizations depend on the reliable operation of their data centers for their day to day business operations. Data centers are designed with redundant and backup power supplies, redundant data communications connections, robust cybersecurity protocols and very strict environmental controls. The many computer systems held in a typical data center generate large heat loads that need to be continuously removed with high grade air conditioning systems. Anthem currently owns a large corporate data center in …

Tracking Surgical Instruments, Akia Wells, Samuel Samvura, Brandon Santiago

Capstone Design Expo Posters

Surgical instruments and sponges are mistakenly left inside patients for more than a dozen times a day. Hospitalizations involving a lost instrument or sponge can average costing more than $60,000 for a hospital. The objective of this design project is to develop a simple, innovative tracking flow process that will better keep track of surgical instruments and sponges before and after surgeries. Using high temperature stickers with matrix barcode technology attached to the surgical instruments, the instruments will be easily scanned into a database to track when instruments are checked in and checked out. Before all instruments are used and …

3d Printed Microwave Hyperthermia Applicator, Umar Hasni, Christopher Deloglos, Patricia Moseh

Capstone Design Expo Posters

According to the CDC, every year approximately two million people are diagnosed with some type of cancer in the United States alone. Common procedures for cancer treatment include surgery, chemotherapy, and radiation therapy. Hyperthermia, an effective collateral treatment, is not included as part of regular cancer care. This is primarily due to its high cost.

Clinical studies for hyperthermia coupled with chemotherapy/radiation therapy have indicated up to a three-fold increase in survival rates of cancer patients. Unfortunately, current microwave hyperthermia systems are bulky, expensive and require special infrastructure in hospitals thus driving up the cost. The objective of this project …

Alterations In Active And Passive Behavior Of Lower Back Tissues Following Six Sessions Of High Velocity Low Amplitude Spinal Manipulative Therapy For Healthy Participants, Emily C. Croft

Theses and Dissertations--Biomedical Engineering

Non-specific low back pain (LBP) is a major health problem affecting a substantial portion of the population. The current treatments offered for non-specific LBP are oftentimes unsuccessful because the acting mechanism(s) of most treatment options are unknown. Obtaining a better understanding about the acting mechanism behind existing treatment options is, therefore, essential for the improvement of non-specific LBP treatment and management. The objective of this study was to gain a more comprehensive understanding about the acting mechanism of high velocity low amplitude spinal manipulative therapy, specifically the impact that high velocity low amplitude spinal manipulative therapy may have on the …

Vehicle Level Transient Aircraft Thermal Management Modeling And Simulation, Adam Donovan

Browse all Theses and Dissertations

Many advances in technology are expected to increase the capabilities of next generation aircraft, and these advances will increase the thermal load on the aircraft as well. In order to assess and account for these increased thermal loads, three studies were performed: a fuel pump trade study, a high energy pulsed system (HEPS) implementation study, and a legacy vehicle environmental control system (ECS) study. The fuel pump study addresses the effect of the implementation of a centrifugal fuel pump versus a variable displacement fuel pump. Traditionally, aircraft designers have used a centrifugal fuel pump over a piston based pump based …

Development, Design, Manufacture And Test Of Flapping Wing Micro Aerial Vehicles, Todd J. Smith

Browse all Theses and Dissertations

The field of FlappingWing Micro Air Vehicles (FWMAV) has been of interest in recent years and as shown to have many aerodynamic principles unconventional to traditional aviation aerodynamics. In addition to traditional manufacturing techniques, MAVs have utilized techniques and machines that have gained significant interest and investment over the past decade, namely in additive manufacturing. This dissertation discusses the techniques used to manufacture and build a 30 gram-force (gf) model which approaches the lower limit allowed by current commercial off-the-shelf items. The vehicle utilizes a novel mechanism that minimizes traditional kinematic issues associated with four bar mechanisms for flapping wing …

Dynamic Visualization Of Three- Dimensional Images From Multiple Texel Images Created From Fused Ladar/Digital Imagery, Cody C. Killpack, Scott Budge

Electrical and Computer Engineering Faculty Publications

The ability to create three-dimensional (3-D) image models, using registered texel images (fused ladar and digital imagery), is an important topic in remote sensing. These models are automatically generated by matching multiple texel images into a single common reference frame. However, rendering a sequence of independently registered texel images often provides challenges. Although accurately registered, the model textures are often incorrectly overlapped and interwoven when using standard rendering techniques. Consequently, corrections must be done after all the primitives have been rendered by determining the best texture for any viewable fragment in the model. This paper describes a technique to visualize …

Marco, Micro, Structure, Agency: Analysing Approaches To Engineering Ethics, Eddie Conlon

Books/Book Chapters

No abstract provided.

An Alternative Stiffening Method For Rigid Chs L- Joints, Niall Holmes, Darran Kierans, Patrick Crean

Articles

No abstract provided.

Case Studies Of Cavity And External Wall Insulation Retrofitted Under The Irish Home Energy Saving Scheme: Technical Analysis And Occupant Perspectives, Aimee Byrne, Gerard Byrne, Garrett O'Donnell, Anthony Robinson

Articles

The residential sector represents 27% of primary energy consumption in Ireland. This paper examines the case study of the Irish government’s national grant scheme to encourage energy efficiency retrofit in private housing. That is the Home Energy Saving (HES) Scheme, later rebranded the Better Energy: Homes (BEH) Scheme. The methodology involved monitoring several homes immediately before and after retrofit alongside discussions with occupants. The examination focused on specific measures commonly introduced through the HES/BEH programme − cavity and external wall insulation. It has been found that a significant decrease in heat loss through the walls was measured in all cases. …

Cement Based Batteries And Their Potential For Use In Low Power Operations, Aimee Byrne, Niall Holmes, Brian Norton

Articles

This paper presents the development of an innovative cement-electrolyte battery for low power operations such as cathodic protection of reinforced concrete. A battery design was refined by altering different constituents and examining the open circuit voltage, resistor loaded current and lifespan. The final design consisted of a copper plate cathode, aluminium plate anode, and a cement electrolyte which included additives of carbon black, plasticiser, Alum salt and Epsom salt. A relationship between age, temperature and hydration of the cell and the current it produced was determined. It was found that sealing the battery using varnish increased the moisture retention and …

Structural Control Of Wind Turbines With Soil Structure Interaction Included, Breiffni Fitzgerald, Biswajit Basu

Articles

The importance of considering soil structure interaction in structural control of wind turbines is investigated in this paper. An Euler–Lagrangian wind turbine mathematical model based on an energy formulation was developed for this purpose which considers the structural dynamics of the system and the interaction between in-plane and out-of-plane blade vibrations. Also, the interaction between the blades and the tower including a tuned mass damper (TMD) is considered. The turbine is subject to turbulent aerodynamic loading simulated using a modification to the classic Blade Element Momentum (BEM) theory with turbulence generated from rotationally sampled spectra. The turbine is also subject …

Biofilm Growth Kinetics And Nutrient (N/P) Adsorption In An Urban Lake Using Reclaimed Water: A Quantitative Baseline For Ecological Health Assessment, Tianzhi Wang, Zhenci Wu, Yunkai Li, Mingchao Liang, Zhenhua Wang, Paul Hynds

Articles

Reclaimed wastewater reuse represents an effective method for partial resolution of increasing urban water shortages; however, reclaimed water may be characterized by significant contaminant loading, potentially affecting receiving ecosystem (and potentially human) health. The current study examined biofilm growth and nutrient adsorption in Olympic Lake (Beijing), the largest artificial urban lake in the world supplied exclusively by reclaimed wastewater. Findings indicate that solid particulate, extracellular polymeric substance (EPS) and metal oxide (Al, Fe, Mn) constituent masses adhere to a bacterial growth curve during biofilm formation and growth. Peak values were observed after ≈30 days, arrived at dynamic stability after ≈50days …