Engineering Commons^™

Logan River Restoration Draft Conservation Action Plan, Logan River Task Force

All In-stream Flows Material

The Logan River, an integral part of the greater Bear River ecosystem, originates within the Bear River Mountains in the headwaters of Logan Canyon and terminates at its confluence with the Little Bear River in Cutler Reservoir. The river is an asset to residents of Logan City and Cache County and has historically supported many beneficial uses. The Logan River was an important resource for Native Americans and pioneers, and it remains valuable today. Cache Valley citizens are attracted to the river and enjoy the aesthetics, recreational values, and wildlife resources associated with this high-quality river, which supports fish, wildlife, …

Temperature Measurements During High Flux Ion Beam Irradiations, M. L. Crespillo, Joseph T. Graham, Y. Zhang, W. J. Weber

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

A systematic study of the ion beam heating effect was performed in a temperature range of -170 to 900 °C using a 10 MeV Au³⁺ ion beam and a Yttria stabilized Zirconia (YSZ) sample at a flux of 5.5 x 10¹² cm^-2 s^-1. Different geometric configurations of beam, sample, thermocouple positioning, and sample holder were compared to understand the heat/charge transport mechanisms responsible for the observed temperature increase. The beam heating exhibited a strong dependence on the background (initial) sample temperature with the largest temperature increases occurring at cryogenic temperatures and decreasing with increasing temperature. …

Synchronization Of Pulse-Coupled Oscillators To A Global Pacemaker, Felipe Nunez, Yongqiang Wang, Andrew R. Teel, Francis J. Doyle Iii

Publications

Pulse-coupled oscillators (PCOs) are limit cycle oscillators coupled by exchanging pulses at discrete time instants. Their importance in biology and engineering has motivated numerous studies aiming to understand the basic synchronization properties of a network of PCOs. In this work, we study synchronization of PCOs subject to a global pacemaker (or global cue) and local interactions between slave oscillators. We characterize solutions and give synchronization conditions using the phase response curve (PRC) as the design element, which is restricted to be of the delay type in the first half of the cycle, interval (0,π)(0,π), and of the advance type in …

Design And Performance Evaluation Of A Prototype Mrf-Based Haptic Interface For Medical Applications, Mehrdad Kermani Ph.D., P.Eng., Nima Najmaei, Ali Asadian, Rajni Patel

Electrical and Computer Engineering Publications

This paper describes the construction and stability and transparency evaluation of a prototype two degrees-of-freedom (DoF) haptic interface, which takes ad-vantage of magneto-rheological fluid (MRF)-based clutches for actuation. These small-scale clutches were designed in our lab, and their evaluation were reported previously [1],[2]. MRF-based actuators exhibit superior characteristics,which can significantly contribute to transparency and stability of haptic devices. Based on these actuators, a distributed antagonistic configuration is used to develop the2-DoF haptic interface. This device is incorporated in a master–slave teleoperation setup intended for medical per-cutaneous interventions and soft-tissue palpation. Preliminary studies on the stability and transparency of the haptic …

Airborne Lidar Acquisition, Post-Processing And Accuracy-Checking For A 3d Webgis Of Copan, Honduras, Jennifer Von Schwerin, Heather Richards-Rissetto, Fabio Remondino, Maria Grazia Spera, Michael Auer, Nicolas Billen, Lukas Loos, Laura Stelson, Markus Reindel

Department of Anthropology: Faculty Publications

Archaeological projects increasingly collect airborne LiDAR data to use as a remote sensing tool for survey and analysis. Publication possibilities for LiDAR datasets, however, are limited due to the large size and often proprietary nature of the data. Fortunately, web-based, geographic information systems (WebGIS) that can securely manage temporal and spatial data hold great promise as virtual research environments for working with and publishing LiDAR data. To test this and to obtain new data for archaeological research, in 2013, the MayaArch3D Project (www.mayaarch3d.org) collected LiDAR data for the archaeological site of Copan, Honduras. Results include: 1) more accurate archaeological maps, …

Channel Estimation, Carrier Recovery, And Data Detection In The Presence Of Phase Noise In Ofdm Relay Systems, Rui Wang, Hani Mehrpouyan, Meixia Tao, Yingbo Hua

Electrical and Computer Engineering Faculty Publications and Presentations

Due to its time-varying nature, oscillator phase noise can significantly degrade the performance of channel estimation, carrier recovery, and data detection blocks in high-speed wireless communication systems. In this paper, we analyze joint channel, carrier frequency offset (CFO), and phase noise estimation plus data detection in orthogonal frequency division multiplexing (OFDM) relay systems. To achieve this goal, a detailed transmission framework involving both training and data symbols is presented. In the data transmission phase, a combtype OFDM symbol consisting of both pilots and data symbols is proposed to track phase noise over an OFDM frame. Next, a novel algorithm …

A Novel Compressed Sensing Method For Magnetic Resonance Imaging: Exponential Wavelet Iterative Shrinkage-Thresholding Algorithm With Random Shift, Yudong Zhang, Jiquan Yang, Jianfei Yang, Aijun Liu, Ping Sun

Publications and Research

Aim. It can help improve the hospital throughput to accelerate magnetic resonance imaging (MRI) scanning. Patients will benefit from less waiting time. Task. In the last decade, various rapid MRI techniques on the basis of compressed sensing (CS) were proposed. However, both computation time and reconstruction quality of traditional CS-MRI did not meet the requirement of clinical use.

Method. In this study, a novel method was proposed with the name of exponential wavelet iterative shrinkagethresholding algorithm with random shift (abbreviated as EWISTARS). It is composed of three successful components: (i) exponential wavelet transform, (ii) iterative shrinkage-thresholding algorithm, and (iii) randomshift. …

Not-So-Risky Business? Assessing The Risk Of Integrating Large Rpvs Into The Current Air Traffic System, Hans-Joachim K. Ruff-Stahl, Steven Esser, Dirk Farsch, Thomas Graner, Robert Klein, Christian Schneidt, Stefan Schoenborn

International Journal of Aviation, Aeronautics, and Aerospace

In spite of considerable efforts to commercialize large remotely piloted vehicles (RPV), an integration of these RPVs into the existing Air Transportation System (ATS) and Airspace Structure is pending. The purpose of this paper was to assess the risks of an exemplary integration of a Heron 1 type RPV into the existing European air space structure within the current regulatory framework and without the availability of sense and avoid technology. Six incident occurrence scenarios were investigated, based on a modified Fault Tree Analysis and Eurocontrol’s risk matrix. It was found that without the implementation of technological or procedural changes, an …

Long-Term Velaglucerase Alfa Treatment In Children With Gaucher Disease Type 1 Naïve To Enzyme Replacement Therapy Or Previously Treated With Imiglucerase, Laurie Smith, William Rhead, Joel Charrow, Suma P. Shankar, Ashish Bavdekar, Nicola Longo, Rebecca Mardach, Paul Harmatz, Thomas N. Hangartner, Hak-Myung Lee, Eric Crombez, Gregory M. Pastores

Biomedical, Industrial & Human Factors Engineering Faculty Publications

Background

Gaucher Disease type 1 (GD1) often manifests in childhood. Early treatment with enzyme replacement therapy (ERT) may prevent disease complications. We report the assessment of velaglucerase alfa ERT in pediatric GD1 patients who participated in a long-term extension study (HGT-GCB-044, ClinicalTrials.gov Identifier NCT00635427).

Methods

Safety and efficacy were evaluated in pediatric patients receiving velaglucerase alfa 30–60 U/kg by intravenous infusion every other week. In addition to key hematological and visceral efficacy assessments, exploratory assessments conducted specifically in pediatric patients included evaluation of height, bone age, bone marrow burden, and Tanner stage of puberty.

Results

The study included 24 …

Implementation Of Space-Time Finite Element Formulation In Elastodynamics, Sidharth Ramesh

Graduate Theses - Mechanical Engineering

Elastodynamics is an academic field that is involved in solving problems related to the field of wave propagation in continuous solid medium. Finite element methods have long been an accepted way of solving elastodynamics problems in the spatial dimension. Considerable thought has been given to ways of implementing finite element discretization in the temporal dimension as well. A particular method of finite element solving called space-time finite element formulation is explored in this thesis, which is a relatively recent technique for discretization in spatial and temporal dimensions. The present thesis explores the implementation of the Space-Time finite element formulation in …

Introduction To Biomedical Engineering, Maribel Vazquez

Open Educational Resources

An overview of the field of biomedical engineering designed to acquaint the students with its interdisciplinary nature; research areas presented by the biomedical engineering faculty.

Characterization Of Silica-Based And Borate-Based, Titanium-Containing Bioactive Glasses For Coating Metallic Implants, Omar Rodriguez, Declan J. Curran, Marcello Papini, Lana M. Placek, Anthony W. Wren, Emil H. Schemitsch, Paul Zalzal, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Bioactive glasses have found applications in diverse fields, including orthopedics and dentistry, where they have been utilized for the fixation of bone and teeth and as scaffolds for drug delivery. The present work outlines the characterization of two novel titanium-containing glass series, one silica-based and one borate-based. For the silica-based series, titanium is added at the expense of silicon dioxide whereas for the borate-based series, it is added at the expense of boron oxide as confirmed by Energy Dispersive Spectroscopy. Amorphous structures are obtained for silica-based glass at 15 mol% TiO₂ and for borate-based glasses at 0 mol% and …

Error-Compensation Method For Inclination Measurement Under The Influence Of The Dynamic Interference, Yanshun Zhang, Yajing Guo, Kui Li, Chaoying Pei, Ming Li

Mechanical and Aerospace Engineering Faculty Research & Creative Works

To deal with the problem of the inclination measurement errors caused by the dynamic motions, such as rotational and accelerated rectilinear components, this paper puts forward an effective inclination measurement scheme and the corresponding error-compensation method based on one accelerometer and two gyroscopes. In addition, the principal prototype of the dynamic inclination measurement apparatus is set up to conduct experiments of turntable rotation test, trolley test, and the turntable sway test at different inclined angles, thus verifying the feasibility of the error-compensation method under the effects of the rotational motion, accelerated rectilinear motion or both motions at the same time. …

Histogram Of Oriented Phase And Gradient (Hopg) Descriptor For Improved Pedestrian Detection, Hussin Ragb, Vijayan K. Asari

Electrical and Computer Engineering Faculty Publications

This paper presents a new pedestrian detection descriptor named Histogram of Oriented Phase and Gradient (HOPG) based on a combination of the Histogram of Oriented Phase (HOP) features and the Histogram of Oriented Gradient features (HOG).

The proposed descriptor extracts the image information using both the gradient and phase congruency concepts. Although the HOG based method has been widely used in the human detection systems, it lacks to deal effectively with the images impacted by the illumination variations and cluttered background. By fusing HOP and HOG features, more structural information can be identified and localized in order to obtain more …

A Real-Time Information Based Demand-Side Management System In Smart Grid, Feng Ye, Yi Qian, Rose Qingyang Hu

Electrical and Computer Engineering Faculty Publications

In this paper, we study a real-time information based demand-side management (DSM) system with advanced communication networks in smart grid. DSM can smooth peak-to-average ratio (PAR) of power usage in the grid, which in turn reduces the waste of fuel and the emission of greenhouse gas. We first target to minimize PAR with a centralized scheme. To motivate power suppliers, we further propose another centralized scheme targeting minimum power generation cost. However, customers may not be motivated by a centralized scheme since such a scheme requires total control and privacy from them. A centralized scheme also requires too much real-time …

Erratum: "Composition- And Pressure-Induced Ferroelectric To Antiferroelectric Phase Transitions In Sm-Doped Bifeo₃ System" [Appl. Phys. Lett. 106, 012903 (2015)], Fei Xue, Linyun Liang, Yijia Gu, Ichiro Takeuchi, Sergei V. Kalinin, Long-Qing Chen

Materials Science and Engineering Faculty Research & Creative Works

In the acknowledgement of the original article, the Award No. DMR-0820404 should be replaced by DMR-1420620.

A Ridge-Fed Conical Horn Antenna For Small Satellites, Arjun Gupta

Electrical and Computer Engineering ETDs

The increased popularity of small satellites such as CubeSats as an alternative vehicle for efficient and low cost space exploration has revolutionized the space research industry. The small physical size and other constraints owing to outer space applications has presented a myriad of exciting opportunities for antenna engineers to come up with alternative solutions to meet the ever evolving needs of the CubeSat applications. The advancement of technology has enabled small satellites to carry out sophisticated missions such as space weather monitoring, space telescopes, imaging and relaying of information from distant satellites. Advanced applications require a high speed downlink with …

Design Live Load Factor Calibration For Michigan Highway Bridges, Christopher D. Eamon, Valid Kamjoo, Kazuhiko Shinki

Civil and Environmental Engineering Faculty Research Publications

In this study, a reliability-based calibration of live load factors for bridge design specific to the State of Michigan was conducted. Two years of high frequency WIM data from 20 representative state-wide sites were analyzed, and load effects were generated for bridge spans from 6 to 122 m (20 to 400 ft), considering simple and continuous moments and shears, as well as single lane and two lane effects. Seventy-five year statistics for maximum live load were then estimated with probabilistic projection. Bridge girders considered for the calibration included composite steel, prestressed concrete, side-by-side and spread box beams, as well as …

Dynamic Transverse Debondong Of A Single S-2 Fiber, Stephen E. Levine

Open Access Theses

Fiber reinforced composites are becoming increasingly common due to their high strength to weight ratios as compared to more conventional materials. Along with this increased used comes the need to have a higher level of understanding of the material characteristics. Specifically, the interface between the fiber and matrix is of particular interest. Loss of adhesion at this interface, known as debonding, can greatly decrease material strength. There has been significant research into debdonding phenomena at low strain rates. However, there is still a need for further insight at higher strain rates. In addition, given the opacity of many epoxy resins, …

Supervised Learning-Based Explicit Nonlinear Model Predictive Control And Unknown Input Estimation In Biomedical Systems, Ankush Chakrabarty

Open Access Dissertations

Application of nonlinear control theory to biomedical systems involves tackling some unique and challenging problems. The mathematical models that describe biomedical systems are typically large and nonlinear. In addition, biological systems exhibit dynamics which are not reflected in the model (so-called 'un-modeled dynamics') and hard constraints on the states and control actions, which exacerbate the difficulties in designing model-based controllers or observers.

This thesis investigates the design of scalable fast explicit nonlinear model predictive controllers (ENMPCs). The design involves (i) the estimation of a feasible region using Lyapunov stability methods and support vector machines; and (ii) within the estimated feasible …

Analysis And Simulation Of Small Scale Microwave Interferometer Experiments On Non-Ideal Explosives, David E. Kittell

Open Access Dissertations

Small scale experiments for non-ideal and homemade explosives (HMEs) were investigated, analyzed, and subsequently modeled in an attempt to develop more predictive capabilities for the threat assessment of improvised explosive devices (IEDs), as well as to provide new analysis capabilities for other investigators in the field. Non-ideal explosives and HMEs are challenging to characterize because of the nearly limitless parameter space (e.g. sample composition, density, particle morphology, etc.) which gives rise to a broad range of explosive sensitivity and performance. Large scale tests, such as rate stick and gap tests, are not feasible for characterizing every HME of interest due …

The Structural Properties Of Ingan Alloys And The Interdependence On The Thermoelectric Behavior, Bahadir Kucukgok, Xuewang Wu, Xiaojia Wang, Zhiqiang Liu, Ian T. Ferguson, Na Lu

Electrical and Computer Engineering Faculty Research & Creative Works

The III-Nitrides are promising candidate for high efficiency thermoelectric (TE) materials and devices due to their unique features which includes high thermal stability. A systematic study of the room temperature TE properties of metalorganic chemical vapor deposition grown InxGa1-xN were investigated for x = 0.07 to 0.24. This paper investigated the role of indium composition on the TE properties of InGaN alloys in particular the structural properties for homogenous material that did not show significant phase separation. The highest Seebeck and power factor values of 507 μV K^-1 and 21.84 x 10^-4 Wm^-1K^-1 were observed, …

Zncdmgse As A Materials Platform For Advanced Photonic Devices: Broadband Quantum Cascade Detectors And Green Semiconductor Disk Lasers, Joel De Jesus

Dissertations, Theses, and Capstone Projects

The ZnCdMgSe family of II-VI materials has unique and promising characteristics that may be useful in practical applications. For example they can be grown lattice matched to InP substrates with lattice matched bandgaps that span from 2.1 to 3.5 eV, they can be successfully doped n-type, have a large conduction band offset (CBO) with no intervalley scattering present when strained, they have lower average phonon energies, and the InP lattice constant lies in the middle of the ZnSe and CdSe binaries compounds giving room to experiment with tensile and compressive stress. However they have not been studied in detail for …

Water Condensation And Protein Adsorption On Hybrid Superhydrophobic-Hydrophilic Surfaces, Bikash Mondal

Dissertations, Theses, and Capstone Projects

This thesis describes the study of protein adsorption and water condensation on hybrid superhydrophobic-hydrophilic surfaces for various technological applications such as diagnostics, artificial organs and medical devices, water collection, and heat transfer.

In the chapter 1, a general introduction to wetting theories, superhydrophobic surface, and hybrid surfaces is given. In chapter 2, design and fabrication of a hybrid superhydrophobic surface for studying dropwise condensation and heat transfer is discussed. Effect of surface chemistry and wettability on protein adsorption is discussed in the chapter 3. Finally, in chapter 4, the protein adsorption study on hybrid superhydrophobic surfaces made by 3D-printing and …

Hyperelastic Modeling Of Wide-Base Tire And Prediction Of Its Contact Stresses, Jaime Hernandez, Imad L. Al-Qadi

Civil and Environmental Engineering Faculty Research and Publications

Description of tire model development using the finite element (FE) method is presented. Three-dimensional tire-pavement contact stresses were predicted for braking, traction, and free rolling using the FE method. Measured load-deflection curves, contact area, and contact stresses were used for model outcome validation. Slide-velocity-dependent friction and accurate input regarding geometry and material properties were considered. The developed tire model, which helped in studying contact stresses variation in each direction, was used to explain the various phenomena taking place at the tire-pavement interface during straight-line rolling. The analysis matrix includes nine rolling conditions and various loads, tire inflation pressures, and speeds. …

Shortest Path Based Decision Making Using Probabilistic Inference, Akshat Kumar

Research Collection School Of Computing and Information Systems

We present a new perspective on the classical shortest path routing (SPR) problem in graphs. We show that the SPR problem can be recast to that of probabilistic inference in a mixture of simple Bayesian networks. Maximizing the likelihood in this mixture becomes equivalent to solving the SPR problem. We develop the well known Expectation-Maximization (EM) algorithm for the SPR problem that maximizes the likelihood, and show that it does not get stuck in a locally optimal solution. Using the same probabilistic framework, we then address an NP-Hard network design problem where the goal is to repair a network of …

Ambient And Smartphone Sensor Assisted Adl Recognition In Multi-Inhabitant Smart Environments, Nirmalya Roy, Archan Misra, Diane Cook

Research Collection School Of Computing and Information Systems

Activity recognition in smart environments is an evolving research problem due to the advancement and proliferation of sensing, monitoring and actuation technologies to make it possible for large scale and real deployment. While activities in smart home are interleaved, complex and volatile; the number of inhabitants in the environment is also dynamic. A key challenge in designing robust smart home activity recognition approaches is to exploit the users’ spatiotemporal behavior and location, focus on the availability of multitude of devices capable of providing different dimensions of information and fulfill the underpinning needs for scaling the system beyond a single user …

Effects Of Intraframe Distortion On Measures Of Cone Mosaic Geometry From Adaptive Optics Scanning Light Ophthalmoscopy, Robert F. Cooper, Yusufu N. Sulai, Adam M. Dubis, Toco Y.P. Chui, Richard B. Rosen, Michel Michaelides, Alfredo Dubra, Joseph Carroll

Biomedical Engineering Faculty Research and Publications

Purpose: To characterize the effects of intraframe distortion due to involuntary eye motion on measures of cone mosaic geometry derived from adaptive optics scanning light ophthalmoscope (AOSLO) images.

Methods: We acquired AOSLO image sequences from 20 subjects at 1.0, 2.0, and 5.08 temporal from fixation. An expert grader manually selected 10 minimally distorted reference frames from each 150-frame sequence for subsequent registration. Cone mosaic geometry was measured in all registered images (n ¼ 600) using multiple metrics, and the repeatability of these metrics was used to assess the impact of the distortions from each reference frame. In nine additional subjects, …

Daylighting And Thermo-Electrical Performance Of An Autonomous Suspended Particle Device Evacuated Glazing, Aritra Ghosh

Doctoral

Suspended particle device (SPD) glazing is an AC powered switchable glazing. PV powered SPD evacuated (vacuum) glazing was proposed with the potential of reducing the heating demand, cooling demand and artificial lighting demand of a building. To achieve an autonomous SPD vacuum glazing, semi empirical simulation and outdoor characterisation was explored in this thesis. Transmission of SPD glazing (area 0.058 m2) varied from 5% when opaque to 55% when transparent in the presence of 110 V, 0.07 W AC supply was characterised in outdoor test cell in Dublin. The SPD glazing has variable spectral transmission in the presence of variable …

Multi-Decadal Satellite Measurements Of Global Volcanic Degassing, S. A. Carn, L. Clarisse, A. J. Prata

Michigan Tech Publications, Part 1

Satellite instruments have been providing measurements of global volcanic emissions of sulfur dioxide (SO2) since 1978, based on observations in the ultraviolet (UV), infrared (IR) and microwave spectral bands. We review recent advances in satellite remote sensing of volcanic gases, focusing on increased instrument sensitivity to tropospheric SO2 emissions and techniques to determine volcanic plume altitude. A synthesis of ~36 years of global UV, IR and microwave satellite measurements yields an updated assessment of the volcanic SO2 flux to the upper troposphere and lower stratosphere (UTLS) between 1978 and 2014 (~1-Tg/yr). The present availability of multiple UV and IR satellite …