Engineering Commons^™

Exploring Travel Time Reliability Using Bluetooth Data Collection: A Case Study In San Luis Obispo, California, Krista Purser

Master's Theses

Bluetooth technology applications have improved travel time data collection efforts and allowed for collection of large data sets at a low cost per data unit. Mean travel times between pairs of points are available, but the primary value of this technique is the availability of the entire distribution of travel times throughout multiple days and time periods, allowing for a greater understanding of travel time variations and reliability. The use of these data for transportation planning, engineering and operations continues to expand. Previous applications of similar data sources have included travel demand and simulation model validation, work zone traffic patterns, …

Finite Element Modeling Of Delamination Damage In Carbon Fiber Laminates Subject To Low-Velocity Impact And Comparison With Experimental Impact Tests Using Nondestructive Vibrothermography Evaluation, George Rodriguez Iv

Master's Theses

Carbon fiber reinforced composites are utilized in many design applications where high strength, low weight, and/or high stiffness are required. While composite materials can provide high strength and stiffness-to-weight ratios, they are also more complicated to analyze due to their inhomogeneous nature. One important failure mode of composite structures is delamination. This failure mode is common when composite laminates are subject to impact loading.

Various finite element methods for analyzing delamination exist. In this research, a modeling strategy based on contact tiebreak definitions in LS-DYNA^®was used. A finite element model of a low-velocity impact event was created to …

Removing Oil From Fried Foods Via Mechanical Process, Yufay Chow-Yee

Master's Theses

Fried foods are delicious and enjoyed by almost everyone. However, they are not the healthiest foods to eat because of the amount of oil they contain. This thesis, sponsored by Moaero Company founder, Mr. Harrish Bhutani, intends to determine whether a simply designed centrifuge system can remove a reasonable amount of oil from fried foods after it has been deep fried without adversely affecting the texture of the fried food. Due to a large variety in the texture as well as the type of fried foods, and in order to keep the scope of this thesis more focused and feasible, …

Design Of Inexpensive And Easy To Use Diy Internet Of Things Platform, Samuel R. Jaffe

Master's Theses

This thesis focuses on the design and implementation of a new, inexpensive, and less complex system for a Do-It-Yourself (DIY) Internet of Things (IoT) platform. The hardware aspects focus on a new chip called the ESP8266 which contains both microcontroller and WiFi connectivity capabilities in an extremely affordable package. The system uses the Arduino IDE to program the ESP8266, which is known to be an extremely user-friendly environment. All other software is both free and easy to use. Past methods of creating IoT projects involved either expensive hardware, often ranging from $50-$100 per node, or complicated programming requiring a full …

Sysml Based Cubesat Model Design And Integration With The Horizon Simulation Framework, Shaun Luther

Master's Theses

This thesis examines the feasibility of substituting the system input script of Cal Poly’s Horizon Simulation Framework (HSF) with a Model Based Systems Engineering (MBSE) model designed with the Systems Modeling Language (SysML). A concurrent student project, SysML Output Interface Creation for the Horizon Simulation Framework, focused on design of the HSF Translator Plugin which converts SysML models to an HSF specific XML format. A SysML model of the HSF test case, Aeolus, was designed. The original Aeolus HSF input script and the translated SysML input script retained the format and dependency structure required by HSF. Both input scripts …

Physical Testing Of Potential Football Helmet Design Enhancements, Michael Jeremy Schuster

Master's Theses

Football is a much loved sport in the United States. Unfortunately, it is also hard on the players and puts them at very high risk of concussion. To combat this an inventor in Santa Barbara brought a new design to Cal Poly to be tested.

The design was tested in small scale first in order to make some preliminary conclusions about the design. In order to fully test the helmet design; however, full scale testing was required. In order to carry out this testing a drop tower was built based on National Operating Committee on Standards for Athletic Equipment, NOCSAE, …

Exploring Data Driven Models Of Transit Travel Time And Delay, Bobjot Singh Sidhu

Master's Theses

Transit travel time and operating speed influence service attractiveness, operating cost, system efficiency and sustainability. The Tri-County Metropolitan Transportation District of Oregon (TriMet) provides public transportation service in the tri-county Portland metropolitan area. TriMet was one of the first transit agencies to implement a Bus Dispatch System (BDS) as a part of its overall service control and management system. TriMet has had the foresight to fully archive the BDS automatic vehicle location and automatic passenger count data for all bus trips at the stop level since 1997. More recently, the BDS system was upgraded to provide stop-level data plus 5-second …

A Comparison Of Risk Assessment Models For Pipe Replacement And Rehabilitation In A Water Distribution System, Lyle John Nemeth

Master's Theses

A water distribution system is composed of thousands of pipes of varying materials, sizes, and ages. These pipes experience physical, environmental, and operational factors that cause deterioration and ultimately lead to their failure. Pipe deterioration results in increased break rates, decreased hydraulic capacity, and adverse effects on water quality. Pipe failures result in economic losses to the governing municipality due to loss of service, cost of pipe repair/replacement, damage incurred due to flooding, and disruptions to normal business operations. Inspecting the entire water distribution system for deterioration is difficult and economically unfeasible; therefore, it benefits municipalities to utilize a risk …

Feasibility Of Fused Deposition Of Ceramics With Zirconia And Acrylic Binder, Lindsay V. Page

Master's Theses

Processing of ceramics has always been difficult due to how hard and brittle the material is. Fused Deposition of Ceramics (FDC) is a method of additive manufacturing which allows ceramic parts to be built layer by layer, abetting more complex geometries and avoiding the potential to fracture seen with processes such as grinding and milling. In the process of FDC, a polymeric binder system is mixed with ceramic powder for the printing of the part and then burned out to leave a fully ceramic part. This experiment investigates a new combination of materials, zirconia and acrylic binder, optimizing the process …

Polyfs Visualizer, Paul Martin Fallon

Master's Theses

One of the most important operating system topics, file systems, control how we store and access data and form a key point in a computer scientists understanding of the underlying mechanisms of a computer. However, file systems, with their abstract concepts and lack of concrete learning aids, is a confusing subjects for students. Historically at Cal Poly, the CPE 453 Introduction to Operating Systems has been on of the most failed classes in the computing majors, leading to the need for better teaching and learning tools. Tools allowing students to gain concrete examples of abstract concepts could be used to …

An Iteration On The Horizon Simulation Framework To Include .Net And Python Scripting, Morgan Yost

Master's Theses

Modeling and Simulation is a crucial element of the aerospace engineering design pro- cess because it allows designers to thoroughly test their solution before investing in the resources to create it. The Horizon Simulation Framework (HSF) v3.0 is an aerospace modeling and simulation tool that allows the user to verify system level requirements in the early phases of the design process. A low fidelity model of the system that is created by the user is exhaustively tested within the built-in Day-in-the-Life simulator to provide useful information in the form of failed requirements, system bottle necks and leverage points, and potential …

An Ergonomics Analysis Of Redundancy Effect In Touch Screen Design For The Aged Population, Sarah Riesenberg

Master's Theses

Touch screen technology is rapidly increasing, and at the same time there is a shifting, aging population. As the percentage of the population over the age of 65 increases, adults of the age group are adopting smartphones and tablets more now than ever before. Although older adults are adopting touch screen devices, they face many challenges when interacting with said devices, such as not knowing how to navigate between pages, not knowing where to click for an action to occur, and the touch screen interface is often too sensitive or the buttons are not big enough. Furthermore, the challenges of …

A Solution To The Circular Restricted N Body Problem In Planetary Systems, Jay R. Iuliano

Master's Theses

This thesis is a brief look at a new solution to a problem that has been approached in many different ways in the past - the N body problem. By focusing on planetary systems, satellite dynamics can be modeled in a fashion similar to the Circular Restricted Three Body Problem (CR3BP) with the Circular Restricted N Body Problem (CRNBP). It was found that this new formulation of the dynamics can then utilize the tools created from all the research into the CR3BP to reassess the possibility of different complex trajectories in systems where there are more than just two large …

Low-Frequency Series Loaded Resonant Inverter Characterization, Alfredo Medina

Master's Theses

Modern power systems require multiple conversions between DC and AC to deliver power from renewable energy sources. Recent growth in DC loads result in increased system costs and reduced efficiency, due to redundant conversions. Advances in DC microgrid systems demonstrate superior performance by reducing conversion stages. The literature reveals practical DC microgrid systems composed of wind and solar power to replace existing fossil fuel technologies for residential consumers. Although higher efficiencies are achieved, some household appliances require AC power; thus, the need for highly efficient DC to AC converters is imperative in establishing DC microgrid systems. Resonant inverter topologies exhibit …

The Bottlefly Ios Application For Wine Recommendations, Carson James Carroll

Master's Theses

The use of smartphone applications has taken over the way people interact with the world. The design of an application has become an important aspect in keeping the user engaged [22]. People are looking for applications that are easy to use and will get the job done. This thesis focuses on the design of a mobile application for iOS that recommends wine in various retail locations that match a user’s taste preferences.

The goals of this thesis are to design an iOS application that recommends wine to consumers, improve upon the wine recommendation algorithms by acquiring more customer data, and …

Hall Effect Modeling In Fem Simulators And Comparison To Experimental Results In Silicon And Printed Sensors, Leonardo A. Frem

Master's Theses

Finite element method simulation models for thin-film semiconductor-based Hall sensors were developed using secondary data in order to understand their behavior under strong magnetic fields. Given a device geometry and charge carrier density and mobility, the models accurately calculated sensor resistance, Hall voltage under a normally-incident constant magnetic field, and expected offset from a population of Hall devices. The model was successfully matched against data from integrated chip Hall sensors from St. Jude Medical. Additionally, the feasibility of creating Hall effect devices with common carbon ink was explored experimentally. The material properties obtained from testing these ink-based devices through the …

Design And Testing Of A Top Mask Projection Ceramic Stereolithography System For Ceramic Part Manufacturing, Dylan Robert De Caussin

Master's Theses

Ceramic manufacturing is an expensive process with long lead times between

the initial design and final manufactured part. This limits the use of ceramic as a viable material unless there is a large project budget or high production volume associated with the part. Ceramic stereolithography is an alternative to producing low cost parts through the mixing of a photo curable resin and ceramic particles. This is an additive manufacturing process in which each layer is built upon the previous to produce a green body that can be sintered for a fully dense ceramic part.

This thesis introduces a new approach …

The Effects Of Obesity On Resultant Knee Joint Loads For Gait And Cycling, Juan Gutierrez-Franco

Master's Theses

Osteoarthritis (OA) is a degenerative disease of cartilage and bone tissue and the most common form of arthritis, accounting for US$ 10.5 billion in hospital charges in 2006. Obesity (OB) has been linked to increased risk of developing knee OA due to increased knee joint loads and varus-valgus misalignment. Walking is recommended as a weight-loss activity but it may increase risk of knee OA as OB gait increases knee loads. Cycling has been proposed as an alternative weight-loss measure, however, lack of studies comparing normal weight (NW) and OB subjects in cycling and gait hinder identification of exercises that may …

Characterizing Neurotransmitter Receptor Activation With A Perturbation Based Decomposition Method, Stephen Gregory Jue

Master's Theses

The characterization of postsynaptic potentials, in terms of neurotransmitter receptor activation, is of clinical significance because information associated with receptor activation can be used in the diagnosis and study of neurological disorders. Single-unit recordings provide a method of measuring postsynaptic potentials in neurons using a microelectrode system, but yield no detailed information regarding the neurotransmitter receptors that contribute to the potential. To determine the types of neurotransmitter receptors that result in a compound postsynaptic potential from a microelectrode reading, decomposition of the potential is necessary. In this work, a perturbation-based decomposition method developed by R. Szlavik is evaluated for this …

Analysis Of Various Algorithmic Approaches To Software-Based 1200 Baud Audio Frequency Shift Keying Demodulation For Aprs, Robert F. Campbell

Master's Theses

Digital communications continues to be a relevant Field of study as new technologies appear and old methodologies get revisited or renovated. The goal of this research is to look into the old digital communication scheme of Bell 202 [67] used by APRS and improve software based demodulation performance. Improved performance is defined by being able to correctly decode more packets in an efficient, real time, manner. Most APRS demodulation is currently done using specialized hardware since that yields the best performance. This research shows that through using Sivan Toledo's javAX25 [72] software package, new demodulation algorithms can be implemented that …

Processing Of Simulated And Experimental Images Of Closely Spaced Binary Stars Using Speckle Interferometry, Niels Smidth

Master's Theses

Theory and methods of processing speckle interferometry data from close visual binary stars are presented and implemented. The effects of the optical systems used for observing close visual binary stars are explained and simulated from both the geometrical and physical optical viewpoints. The atmospheric phase distortion and shot noise responsible for the observed speckle patterns are simulated. The deconvolution technique originally presented by Labeyrie is implemented to extract astrometric data from close visual binary stars. This method is applied to both simulated and experimental data from Kitt Peak National Observatory as validation. Parts of the deconvolution process are optimized to …

Benefits Of Advanced Traffic Management Solutions: Before And After Crash Analysis For Deployment Of A Variable Advisory Speed Limit System, Alexander Lindsay Chambers

Master's Theses

Variable speed limit (VSL) systems are important active traffic management tools that are being deployed across the U.S. and indeed around the world for relieving congestion and improving safety. Oregon’s first variable advisory speed limit signs were activated along Oregon Highway 217 in the summer of 2014. The variable advisory speed system is responsive to both congestion and weather conditions. This seven-mile corridor stretches around Western Portland and has suffered from high crash rates and peak period congestion in the past. VSL systems are often deployed to address safety, mobility and sustainability related performance. This research seeks to determine whether …

Wavelength Accuracy Study For High-Density Fiber Bragg Grating Sensor Systems Using A Rapidly-Swept Akinetic-Laser Source, Jacob Egorov

Master's Theses

This thesis studies the center wavelength accuracy of a Fiber Bragg Grating Sensor system that has a large number of sensor elements both as a function of wavelength and as a function of position. Determining the center wavelength of each of the fiber optic sensors is a critical parameter that ultimately determines sensor accuracy. The high density environment can result in degradation of accuracy of the center wavelength measurement. This thesis aims to quantify this measurement error both with theoretical and experimental studies.

There are many sensing applications where optical fiber sensors are preferred over electrical sensors, such as the …

Bunch Splitting Simulations For The Jleic Ion Collider Ring, R. Gamage, T. Satogata

Physics Faculty Publications

We describe the bunch splitting strategies for the proposed JLEIC ion collider ring at Jefferson Lab. This complex requires an unprecedented 9:6832 bunch splitting, performed in several stages. We outline the problem and current results, optimized with ESME including general parameterization of 1:2 bunch splitting for JLEIC parameters.

Incorporating Histograms Of Oriented Gradients Into Monte Carlo Localization, Michael K. Norris

Master's Theses

This work presents improvements to Monte Carlo Localization (MCL) for a mobile robot using computer vision. Solutions to the localization problem aim to provide fine resolution on location approximation, and also be resistant to changes in the environment. One such environment change is the kidnapped/teleported robot problem, where a robot is suddenly transported to a new location and must re-localize. The standard method of "Augmented MCL" uses particle filtering combined with addition of random particles under certain conditions to solve the kidnapped robot problem. This solution is robust, but not always fast. This work combines Histogram of Oriented Gradients (HOG) …

Bathymetric Survey For Lakes Azuei And Enriquillo, Hispaniola, Michael Piasecki, Mahrokh Moknatian, Fred Moshary, Joseph Cleto, Yolanda Leon, Jorge Gonzalez, Daniel Comarazamy

Publications and Research

The two largest lakes on the Caribbean Island of Hispaniola, Lake Azuei in Haiti and Lake Enriquillo in the Dominican Republic, have experienced dramatic growth and surface area expansion over the past few years leading to severe flooding and loss of arable land around the lake perimeters. In order to better understand the reasons for this unprecedented rate of expansion and the resulting consequences a multi-disciplinary team comprised of researchers from Haiti, the DR, and the US have embarked on an extensive data collecting and hydrologic and climatological modeling campaign. While the sensor deployment entails stations that measure climatological data …

Assessment Of A Writing Workshop Model For First-Year Engineering Students, Patricia Backer

Faculty Publications

This paper will report on a multi-year project to improve the writing skills of engineering freshmen at XXX University. For the last ten years, the college has offered an optional class to students who are not proficient in writing. Students can enroll in a one-unit lab class as many semesters as they wish to get practice in writing. The goal is to provide students with weekly writing activities that include: instruction in basic grammar, proofreading, and editing. In addition to study and practice exercises, students in this writing workshop have writing assignments, which provide practice in using correct grammar, spelling, …

Maker: Redesign Of A Multipurpose Hardware Tool To Improve Its Functionality And Marketability, David Alexander, Vimal Viswanathan, Shraddha Sangelkar, Johnathan Moody

Faculty Publications, Mechanical Engineering

In this maker project, we redesigned a hardware tool that is primarily used by linemen working in power companies. At the top of the posts where they work, it is essential to have easily accessible and easy-to-use tools with firm grip. With the use of a multi-purpose product that combines the functionalities of many other common tools, the handling of the tools can be made easy. This maker project is conducted as a case study for a larger research study where the investigators developed a new set of guidelines for the development of multi-purpose products. Though multi-purpose products are very …

User Interface Design Recommendations For Small Unmanned Aircraft Systems (Suas), Camilo Jimenez, Caitlin L. Faerevaag, Florian Jentsch

International Journal of Aviation, Aeronautics, and Aerospace

The number of small unmanned aircraft systems (sUAS) has dramatically increased in recent years. As a consequence, the number of incidents involving manned and unmanned aircraft has soared. For this reason, the Federal Aviation Administration has released a notice of proposed rulemaking to delineate the operational limitations for sUAS. Many efforts have been introduced to regulate the operations of these systems and educate operators. Despite these efforts, there are no clear standards related to the type of information that should be available to operators, or how this information should be conveyed during flight operations. For this reason we present a …

Design And Analysis Of Two Compliant Mechanism Designs For Use In Minimally Invasive Surgical Instruments, Jason Lon Dearden

Theses and Dissertations

Minimally invasive surgery (MIS) has several advantages over traditional methods. Scaling MIS instruments to smaller sizes and increasing their performance will enable surgeons to offer new procedures to a wider range of patients. In this work, two compliant mechanism-based minimally invasive surgical instrument wrist or gripper mechanisms are designed and analyzed.The cylindrical cross-axis flexural pivot (CCAFP) is a single-degree-of-freedom wrist mechanism that could be combined with existing gripper mechanisms to create a multi-degree-of freedom instrument. The simplicity of the CCAFP mechanism facilitates analysis and implementation. The flexures of the CCAFP are integral with the instrument shaft, enabling accessories to be …