Engineering Commons^™

Monitoring Of Tissue Optical Properties During Thermal Coagulation Of Ex Vivo Tissues, Vivek K. Nagarajan, Bing Yu

Biomedical Engineering Faculty Research and Publications

Background and Objective

Real-time monitoring of tissue status during thermal ablation of tumors is critical to ensure complete destruction of tumor mass, while avoiding tissue charring and excessive damage to normal tissues. Currently, magnetic resonance thermometry (MRT), along with magnetic resonance imaging (MRI), is the most commonly used technique for monitoring and assessing thermal ablation process in soft tissues. MRT/MRI is very expensive, bulky, and often subject to motion artifacts. On the other hand, light propagation within tissue is sensitive to changes in tissue microstructure and physiology which could be used to directly quantify the extent of tissue damage. Furthermore, …

Segmental Kinematic Analysis Of Planovalgus Feet In Children With Cerebral Palsy, K. Kruger, K. Konop, Joseph Krzak, Adam Graf, Gerald F. Harris

Biomedical Engineering Faculty Research and Publications

No abstract provided.

Scenario Analysis For Techno-Economic Model Development Of U.S. Offshore Wind Support Structures, Rick Damiani, Andrew Ning, Ben Maples, Aaron Smith, Katherine Dykes

Faculty Publications

Challenging bathymetry and soil conditions of future U.S. offshore wind power plants might promote the use of multimember, fixed-bottom structures (or “jackets”) in place of monopiles. Support structures affect costs associated with the balance of system (BOS) and operation and maintenance. Understanding the link between these costs and the main environmental design drivers is crucial in the quest for a lower levelized cost of energy (LCOE), and it is the main rationale for this work. Actual cost and engineering data are still scarce; hence, we evaluated a simplified engineering approach to tie key site and turbine parameters (e.g., water depth, …

Propulsion Theory Of Flapping Airfoils, Comparison With Computational Fluid Dynamics, Doug F. Hunsaker, W. F. Phillips

Mechanical and Aerospace Engineering Faculty Publications

It is shown that the time-dependent aerodynamic forces acting on a flapping airfoil in forward flight are functions of both axial and normal reduced frequencies. The axial reduced frequency is based on the chord length, and the normal reduced frequency is based on the plunging amplitude. Furthermore, the time-dependent aerodynamic forces are related to two Fourier coefficients, which are evaluated here from computational results. Correlation equations for these Fourier coefficients are obtained from a large number of grid- and time-step-resolved inviscid computational-fluid-dynamics solutions, conducted over a range of both axial and normal reduced frequencies. The correlation results can be used …

Developers’ Perceptions On Object-Oriented Design And Architectural Roles, Maurício Aniche, Marco Aurélio Gerosa, Christoph Treude

Research Collection School Of Computing and Information Systems

Software developers commonly rely on well-known software architecture patterns, such as MVC, to build their applications. In many of these patterns, classes play specific roles in the system, such as Controllers or Entities, which means that each of these classes has specific characteristics in terms of object-oriented class design and implementation. Indeed, as we have shown in a previous study, architectural roles are different from each other in terms of code metrics. In this paper, we present a study in a software development company in which we captured developers’ perceptions on object-oriented design aspects of the architectural roles in their …

Improving Carbon Efficiency Through Container Size Optimization And Shipment Consolidation, Nang Laik Ma, Kar Way Tan, Edwin Lik Ming Chong

Research Collection School Of Computing and Information Systems

Purpose: Many manufacturing companies that ship goods through full container loads found themselves under-utilizing the containers and resulting in higher carbon footprint per volume shipment. One of the reasons is the choice of non-ideal container sizes for their shipments. Consolidation fills up the containers more efficiently that reduces the overall carbon footprint. The objective of this paper is to support decisions on selection of appropriate combination of container sizes and shipment consolidation for a manufacturing company. We develop two-steps model which first takes the volumes to be shipped as an input and provide the combination of container sizes required; then …

Influent Wastewater Microbiota And Temperature Influence Anaerobic Membrane Bioreactor Microbial Community, Matthew Seib, K. J. Berg, Daniel Zitomer

Civil and Environmental Engineering Faculty Research and Publications

Sustainable municipal wastewater recovery scenarios highlight benefits of anaerobic membrane bioreactors (AnMBRs). However, influences of continuous seeding by influent wastewater and temperature on attached-growth AnMBRs are not well understood. In this study, four bench-scale AnMBR operated at 10 and 25 °C were fed synthetic (SPE) and then real (PE) primary effluent municipal wastewater. Illumina sequencing revealed different bacterial communities in each AnMBR in response to temperature and bioreactor configuration, whereas differences were not observed in archaeal communities. Activity assays revealed hydrogenotrophic methanogenesis was the dominant methanogenic pathway at 10 °C. The significant relative abundance of Methanosaeta at 10 °C concomitant …

Single-Sensor, Cue-Counting Population Density Estimation: Average Probability Of Detection Of Broadband Clicks, Elizabeth T. Küsel, Martin Siderius, David K. Mellinger

Electrical and Computer Engineering Faculty Publications and Presentations

Odontocete echolocation clicks have been used as a preferred cue for density estimation using single-sensor data sets, requiring estimation of detection probability as a function of range. Many such clicks can be very broadband in nature, with 10-dB bandwidths of 20-40 kHz or more. Detection distances are not readily obtained from single-sensor data. Here, the average detection probability is estimated in a Monte Carlo simulation using the passive sonar equation along with transmission loss calculations to estimate the signal-to-noise ratio (SNR) of tens of thousands of click realizations. Continuous-wave (CW) analysis, i.e., single-frequency analysis, is inherent to basic forms of …

Exploitation Of Frequency Information In Continuous Active Sonar, Lisa Zurk, Daniel Rouseff, Scott Schecklman

Electrical and Computer Engineering Faculty Publications and Presentations

In pulsed active sonar, short duration coded waveforms insonify the area of interest. The low duty cycle limits detection opportunities and decreases average energy. A recent concept is continuous active sonar (CAS), which has continuous source transmission over a broad frequency band. The low duty cycle limits detection opportunities and decreases average energy. A recent concept is continuous active sonar (CAS), which has continuous source transmission over a broad frequency band. Previous work by the authors has investigated the utility of extracting the propagation-induced frequency structure in pulsed sonar. The broadband, continuous CAS waveforms particularly lend themselves to this approach. …

Trust In Automation: A Study Of Helicopter Pilot Perception On Enhanced Flight Vision Systems (Efvs), Nicholas Colby Currie

Theses and Dissertations

Trust in automation is a growing field of research that serves a vital role in understanding how humans interact with modern technology. Though automation is certainly becoming more prevalent in many professions, it has become a mainstay in the modern helicopter cockpit. One particular piece of modern aviation technology that incorporates a significant amount of automation is Enhance Flight Vision Systems (EFVS). EFVS technology provides pilots with a wealth of information that enables them to “see” under low visibility conditions, thereby increasing their situational awareness. Though the benefits of EFVS technology are easily recognizable, it is still an automated system …

The Feasibility Of Utilising Compressed Natural Gas As Part Of A Systematic Approach To Establishing The Necessary Groundwork For The Hydrogen Based Transport Economy, James Brunton, John Howlett, David Kennedy

Conference Papers

One key objective for vehicle manufacturers is to develop technology and infrastructure to facilitate the progression from combustion to conversion by the year 2050. In the short to medium term however, the combustion of fossil fuels such as petrol and diesel, coupled with advanced transmission innovations and emission control technology that are governed by strict Euro VI regulations appears to be the main path forward for the transport sector and the environment. This paper presents the feasibility of utilising the developing compressed natural gas network capabilities as part of a systematic approach to establishing the necessary groundwork for a hydrogen …

Large-Scale Design Optimization Of Pm Machines Over A Target Operating Cycle, Alireza Fatemi, Nabeel Demerdash, Thomas W. Nehl, Dan M. Ionel

Electrical and Computer Engineering Faculty Research and Publications

A large-scale finite element model-based design optimization algorithm is developed for improving the drive-cycle efficiency of permanent magnet (PM) synchronous machines with wide operating ranges such as those used in traction propulsion motors. The load operating cycle is efficiently modeled by using a systematic k-means clustering method to identify the operating points representing the high-energy-throughput zones in the torque-speed plane. The machine performance is evaluated over these cyclic representative points using a recently introduced computationally efficient finite element analysis, which is upgraded to include both constant torque and field-weakening operations in the evaluation of the machine performance metrics. In contrast …

Indoor Localization Via Multi-Modal Sensing On Smartphones, Han Xu, Zheng Yang, Zimu Zhou, Longfei Shangguan, Ke Yi, Yunhao Liu

Research Collection School Of Computing and Information Systems

Indoor localization is of great importance to a wide range ofapplications in shopping malls, office buildings and publicplaces. The maturity of computer vision (CV) techniques andthe ubiquity of smartphone cameras hold promise for offering sub-meter accuracy localization services. However, pureCV-based solutions usually involve hundreds of photos andpre-calibration to construct image database, a labor-intensiveoverhead for practical deployment. We present ClickLoc, anaccurate, easy-to-deploy, sensor-enriched, image-based indoor localization system. With core techniques rooted insemantic information extraction and optimization-based sensor data fusion, ClickLoc is able to bootstrap with few images. Leveraging sensor-enriched photos, ClickLoc also enables user localization with a single photo of the …

Metaflow: A Scalable Metadata Lookup Service For Distributed File Systems In Data Centers, Peng Sun, Yonggang Wen, Nguyen Binh Duong Ta, Haiyong Xie

Research Collection School Of Computing and Information Systems

In large-scale distributed file systems, efficient metadata operations are critical since most file operations have to interact with metadata servers first. In existing distributed hash table (DHT) based metadata management systems, the lookup service could be a performance bottleneck due to its significant CPU overhead. Our investigations showed that the lookup service could reduce system throughput by up to 70%, and increase system latency by a factor of up to 8 compared to ideal scenarios. In this paper, we present MetaFlow, a scalable metadata lookup service utilizing software-defined networking (SDN) techniques to distribute lookup workload over network components. MetaFlow tackles …

2016 General Aviation Flight Training Metrics, Steven Hampton, Ken Byrnes, Troy Techau

Publications

The study evaluates training at a collegiate flight training program (Embry-Riddle Aeronautical University) providing metrics for time and costs from zero time to a Commercial certificated Pilot with Instrument and Multi-Engine add-ons. Training times for flights and activities are pulled from a sophisticated database used at Embry-Riddle Aeronautical University (ERAU) and matched with flight and ground school lessons and then further subdivided to determine the amount of time spent training in areas of operation that are prescribed by the Federal Aviation Administration in the published Practical Test Standards and Airman Certification Standards for those seeking pilot licenses and ratings.

Provided …

On Safety Assessment Of Novel Approach To Robust Uav Flight Control In Gusty Environments, Vladimir Golubev, Petr Kazarin, William Mackunis, Sherry Borener, Derek Hufty

Publications

In a follow-up to our previous study, the current work examines the gust-induced “cone of uncertainty” in a small unmanned aerial vehicle’s (UAV) flight trajectory addressed in the context of safety assessments of UAV operations. Such analysis is a critical facet of the integration of unmanned aerial systems (UAS) into the National Airspace System (NAS), particularly in terminal airspace. The paper describes a predictive, robust feedback-loop flight control model that is applicable to various classes of UAVs and unsteady flight-path scenarios. The control design presented in this paper extends previous research results by demonstrating asymptotic (zero steady-state error) altitude regulation …

Application Of Bioinstrumentation In Developing A Pressure Suit For Suborbital Flight, Pedro Llanos, Erik Seedhouse

Publications

This presentation features Embry-Riddle Aeronautical University's U-2 pressure suit. Built to be light and cost-effective, this suit is comfortable, comes in multiple sizes, operates in pressures up to 5 PSID, has an active airflow-based cooling system, and features bio-instrumentation to measure heart rate, breathing rate, skin temperature and other vitals.

Realization Of Point Planar Elastic Behaviors Using Revolute Joint Serial Mechanisms Having Specified Link Lengths, Shuguang Huang, Joseph M. Schimmels

Mechanical Engineering Faculty Research and Publications

This paper presents methods for the realization of 2 × 2 translational compliance matrices using serial mechanisms having only revolute joints, each with selectable compliance. The link lengths of the mechanism and the location of the compliant frame relative to the mechanism base are arbitrary but specified. The realizability of a given compliant behavior is investigated, and necessary and sufficient conditions for the realization of a given compliance with a given mechanism are obtained. These realization conditions are interpreted in terms of geometric relationships among the joints. We show that, for an appropriately sized 3R serial mechanism, any single 2 …

Capacity Building For Sustainable Workforce In The Construction Industry, Edelmiro F. Escamilla, Mohammadreza Ostadalimakhmalbaf

The Professional Constructor

Research has shown that the construction industry will face workforce shortages that will increase delivery cost and completion time. The purpose of this paper is to first identify and synthesize the fundamental factors impacting recruitment and retention of the potential construction workforce. A qualitative approach was employed in order to collect and synthesize known factors related to workforce development and capacity building for the construction industry. The paper then presents a conceptual framework for conducting research on capacity generation of a sustainable construction workforce—by considering the impact of family unit and cultural values, career path perceptions, higher educational attainment, and …

Comparing Owner Perceptions Vs. Performance Reality On Construction Management At Risk Public School Projects, Noel Carpenter, Dennis C. Bausman

The Professional Constructor

Over the past decade construction expenditures for education have reached approximately $350 billion with $195 billion of that total spent on K-12 public schools. Public funding through state and local taxes is the primary source of support for construction and school districts are charged with spending these dollars wisely. Within the confines of procurement statutes school districts must select a delivery method that best suits their needs. Two commonly used delivery methods are Design-Bid-Build and Construction Manager at Risk (CM at Risk). This paper examines qualitative and quantitative data collected from one hundred thirty-seven new K-12 school projects constructed in …

Lengthscale Effects On Exchange Coupling In Co-Pt L10 + L12 Nanochessboards, Eric P. Vetter, Liwei D. Geng, Priya Ghatwai, Dustin A. Gilbert, Yongmei M. Jin, William A. Soffa, Jerrold A. Floro

Michigan Tech Publications, Part 1

The Co-Pt nanochessboard is a quasi-periodic, nanocomposite tiling of L10 and L12 magnetic phases that offers a novel structure for the investigation of exchange coupling, relevant to permanent magnet applications. Periodicity of the tiling is controlled by the rate of cooling through the eutectoid isotherm, resulting in control over the L10-L12 exchange coupling. First order reversal curve analysis reveals a transition from partial coupling to nearly complete exchange-coupling in a Co40.2Pt59.8 nanochessboard structured alloy as the periodicity is reduced below the critical correlation length. Micromagnetic simulations give insights into how exchange coupling manifests in the tiling, and its impact on …

Free Fall Of Self-Consolidating Concrete In Walls Three Meters High, Donald J. Phillippi, Katie Loughmiller, Ray Buyle, Michael Cesena

The Professional Constructor

Self-consolidating concrete, (SCC) is a highly flowable, non-segregating concrete that allows for concrete placement without vibration or external consolidation. SCC also allows rapid concrete placement with reduced labor costs, resulting in vastly improved concrete surface finishes and architectural applications (RMCAO 2009). To accomplish SCC, the concrete industry has developed improvements in high-range water reducer admixtures for flowability and viscosity-modifying admixtures for stability. The current project investigated six specimens, which provided an evaluation of SCC allowed to free fall 3 m (10 ft) that filled wall formwork with different inclinations and amounts of steel reinforcement. The purpose of the investigation was …

A Comparison Of Wavelet And Simplicity-Based Heart Sound And Murmur Segmentation Methods, Joshua David Korven

Master's Theses

Stethoscopes are the most commonly used medical devices for diagnosing heart conditions because they are inexpensive, noninvasive, and light enough to be carried around by a clinician. Auscultation with a stethoscope requires considerable skill and experience, but the introduction of digital stethoscopes allows for the automation of this task. Auscultation waveform segmentation, which is the process of determining the boundaries of heart sound and murmur segments, is the primary challenge in automating the diagnosis of various heart conditions. The purpose of this thesis is to improve the accuracy and efficiency of established techniques for detecting, segmenting, and classifying heart sounds …

Post-Liquefaction Residual Strength Assessment Of The Las Palmas, Chile Tailings Failure, Tristan Reyes Gebhart

Master's Theses

Assessment of post-liquefaction residual strength is needed for the development of empirically-based, predictive correlations for earthquake engineering design. Previous practice commonly assigned negligible strengths to liquefied materials for engineering analysis, producing overly-conservative designs. Increasingly available case history data, and improved analytical tools have allowed for more accurate and less overly-conservative estimation of soil residual strength, improving empirical predictive models. This study provides a new case history to the limited suite of (approximately 30) liquefaction failure case histories available for post-liquefaction in-situ strength predictive correlations.

This case history documents the Las Palmas gold mine tailings dam failure, resulting from seismic-induced liquefaction …

Identification Of Agricultural Land Use In California Through Remote Sensing, Todd Allen Robinson

Master's Theses

Ground truthing actual crop types in an area can be expensive and time-consuming. The California Department of Water Resources attempts to ground truth land use in each county in California every five years. However, this is limited by budgetary constraints and often results in infrequent (more than every ten years) surveying of many counties. An accurate accounting of crops growing in a region is important for a variety of purposes including farm production estimates, groundwater and surface water modeling, evapotranspiration estimation, water planning, research applications, etc. Agricultural land use is continually changing due to development and environmental factors.

Currently, USDA …

Experimentation Of Mode I And Mode Ii Fracture Of Uni-Directional Composites And Finite Element Analysis Of Mode I Fracture Using Cohesive Contact, Joseph Daniel Garrett

Master's Theses

As the use of fiber-reinforced composites has increased over the decades, so has the need to understand the complexity of their failure mechanisms as engineers seek to improve the damage tolerance of composite laminated structures. One of the most prevalent and limiting mode of failure within composite laminates is delamination, since it not only reduces a structures stiffness and strength, but can be very difficult to detect without the use of special non-destructive equipment. Industry testing organizations have utilized several fracture tests in order to characterize the fracture toughness of composite materials under different loading conditions. For this research, ASTM …

Scaled Synthetic Aperture Rader Development, Jason Garvey Schray

Master's Theses

Several previous Cal Poly thesis projects involve synthetic aperture radar (SAR), automatic target recognition (ATR), and tracking. SAR data was either accessed from a publicly available database or generated using complex computer modeling software. The motivation for this dual thesis project is to design and construct a scaled SAR system to support Cal Poly radar projects. Ideally this is a low-cost, high resolution SAR architecture that produces raw range Doppler data for any desired target area. To that end, a scaled SAR system was successfully designed, built, and tested. The current SAR system, however, does not perform azimuthal compression and …

A 3-D Multiplex Paper-Microfluidic Platform, Mitchell Patrick Young

Master's Theses

3-D paper-based microfluidic devices (micoPADs) are small and portable devices made out of paper that offer a promising platform for diagnostic applications outside of a laboratory. These devices are easy to use, low cost, require no power source, and capable of detecting multiple targets simultaneously. The work in this thesis demonstrated the ability of a 3-D paper-microfluidic platform to simultaneously detect 5 targets. Rubber cord stock was used in conjunction with an acrylic housing unit to apply pressure along the edge of the channel. The indirect pressure application was successful in promoting vertical fluid flow between layers. Average channel development …

Thermal Management Using Mems Bimorph Cantilever Beams, Ronald A. Coutu Jr., R. S. Lafleur, J. P.K. Walton, Lavern A. Starman

Electrical and Computer Engineering Faculty Research and Publications

This paper examines a passive cooling technique using microelectromechanical systems (MEMS) for localized thermal management of electronic devices. The prototype was designed using analytic equations, simulated using finite element methods (FEM), and fabricated using the commercial PolyMUMPs™ process. The system consisted of an electronic device simulator (EDS) and MEMS bimorph cantilever beams (MBCB) array with beams lengths of 200, 250, and 300 μm that were tested to characterize deflection and thermal behavior. The specific beam lengths were chosen to actuate in response to heating associated with the EDS (i.e. the longest beams actuated first corresponding to the hottest portion of …

Generalizing Effective Spatial Bandwidth For Pole Location In Mas: The Elliptic Cylinder, James Richie

Electrical and Computer Engineering Faculty Research and Publications

The location of poles in the method of auxiliary sources for 2-D scatterers can be assisted using the effective spatial bandwidth (EBW) of the incident and scattered fields. Previously, only circular boundaries were considered. Here, EBW is extended to noncircular boundaries. Calculations presented for a cylinder with elliptical cross section verify EBW as an additional tool for pole placement for more general geometries.