Engineering Commons^™

Fabrication And Characterization Of Miniaturized Components Based On Extruded Ceramic-Filled Polymer Blends, Khurshida Sharmin

LSU Doctoral Dissertations

The objective of this work is to develop an improved manufacturing process for microstructured ceramic components that is based on co-extrusion. Co-extrusion of structured feedrods holds promise for development of multi-layered, functionally graded and/or textured structures. However, it requires a polymer binder that is difficult to remove before structures can be sintered to full density. A two-step debinding is introduced to eliminate debinding defects that are commonly observed in thermal debinding (TD). Cracking is a major issue due to a lack of pore spaces for outgassing of pyrolysis products in traditional TD. In two-step debinding, a soluble binder is removed …

Constitutive Modeling And Experiments For The Micro And Nano Behaviors In Metals, Cheng Zhang

LSU Doctoral Dissertations

This work addresses the micro- and nano-behaviors in metals through constitutive modeling and experiments. The size effect encountered during nanoindentation experiments, which is known as indentation size effect (ISE), is investigated for metal materials. The ISE is believed to be related with the strain gradient at small indentation depths. Geometrically necessary dislocations (GNDs) are formed in order to accommodate the strain gradient, which results in the increase in the material hardness. The grain boundaries in polycrystalline materials play an important role on the material hardness during nanoindentation experiments as there is a soften-hardening segment in the curve of hardness as …

Influence Of Resonant And Non-Resonant Vibrational Excitation Of Ammonia Molecules In Gallium Nitride Synthesis, Hossein Rabiee Golgir, Yunshen Zhou, Kamran Keramatnejad, Yongfeng Lu

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Attempts on the selective promotion of gallium nitride (GaN) growth were investigated by deploying laserassisted vibrational excitation of reactant molecules, which deposits energy selectively into specific molecules and activate the molecules towards the selected reaction pathways. Laser-assisted metal organic chemical vapor deposition (LMOCVD) of GaN was studied using a wavelength-tunable CO2 laser. The NH-wagging modes (υ2) of ammonia (NH3) precursor molecules are strongly infrared active and perfectly match the emission line of the CO2 laser at 9.219, 10.350, and 10.719 μm. On- and off-resonance excitations of molecules were performed via tuning the incident laser wavelengths at on-resonant wavelength 9.219 μm …

Utilisation Of Iron Ore Tailings As Aggregates In Concrete, Francis Atta Kuranchie, Sanjay Kumar Shukla, Daryoush Habibi, Alireza Mohyeddin

Research outputs 2014 to 2021

Sustainable handling of iron ore tailings is of prime concern to all stakeholders who are into iron ore mining. This study seeks to add value to the tailings by utilising them as a replacement for aggregates in concrete. A concrete mix of grade 40 MPa was prepared in the laboratory with water–cement ratio of 0.5. The concrete were cured for 1, 2, 3, 7, 14 and 28 days. The properties of the concrete such as workability, durability, density, compressive strength and indirect tensile strength were tested. A controlled mix of concrete was also prepared in similar way using conventional materials …

Can Strategic Risk Management Contribute To Enterprise Risk Management? A Strategic Management Perspective, Phil Bromiley, Devaki Rau, Michael K. Mcshane

Finance Faculty Publications

Within the discipline of enterprise risk management (ERM), strategic risk management (SRM) has become a subject of increasing interest to practitioners and academics. To our knowledge, the term “strategic risk management” first appeared in the management literature in 1985 and 1986 (Jammine, 1985; Figenbaum & Thomas, 1986) and in the academic finance literature in 1990 (Rawls and Smithson, 1990), although early usage of the term did not clearly relate to later conceptions. The phrase has been in use even longer than ERM (Bromiley, McShane, Nair, and Rustambekov, 2014). Even with this longevity, the meaning of the term remains unclear, with …

Effect Of Dosage Of Non-Chloride Accelerator Versus Chloride Accelerator On The Cracking Potential Of Concrete Repair Slabs, Thomas F. Meagher

USF Tampa Graduate Theses and Dissertations

Due to strict placement time and strength constraints during the construction of concrete pavement repair slabs, accelerators must be incorporated into the mixture design. Since the most common accelerator, calcium chloride, promotes corrosion of concrete reinforcement, a calcium nitrate-based accelerator was studied as an alternative. To replicate mixtures used in the field, commercial accelerators commonly used in concrete pavement repair slabs were used in the current study. Crack risk of different mixtures was assessed using modeling and cracking frame testing. HIPERPAV modeling was conducted using several measured mixture properties; namely, concrete mechanical properties, strength-based and heat of hydration-based activation energies, …

Efficiency Of A Combined Desalination And Power System Utilising A Multi-Stream Heat Exchange, Alireza Hosseini Araghi, Mehdi Khiadani, Gordon Lucas

Research outputs 2014 to 2021

The aim of this study is to simplify the process of Discharge Thermal Energy Combined Desalination (DTECD) with Power System by integrating the two existing heat exchangers (condensers) into a new multi-stream one. This system is a heat recovery unit, which is used to cogenerate water and power. Two shell & tube condensers operate in a closed power cycle and a desalination system for cooling an ammonia mixture (70% wt.) as a working fluid and condensing a pure vapor respectively. Here, a multi-stream plate condenser is utilized instead of the two low exergy efficiency shell & tube condensers. The results …

Virtualization Components Of The Modern Hypervisor, Sean Mcadams

UNF Graduate Theses and Dissertations

Virtualization is the foundation on which cloud services build their business. It supports the infrastructure for the largest companies around the globe and is a key component for scaling software for the ever-growing technology industry. If companies decide to use virtualization as part of their infrastructure it is important for them to quickly and reliably have a way to choose a virtualization technology and tweak the performance of that technology to fit their intended usage. Unfortunately, while many papers exist discussing and testing the performance of various virtualization systems, most of these performance tests do not take into account components …

Du05, Center For Orthopaedic Biomechanics, Michael D. Harris, Phd, Kevin Shelburne, Phd

Natural Knee Data

No abstract provided.

Du04, Center For Orthopaedic Biomechanics, Michael D. Harris, Phd, Kevin Shelburne, Phd

Natural Knee Data

No abstract provided.

Du03, Center For Orthopaedic Biomechanics, Michael D. Harris, Phd, Kevin Shelburne, Phd

Natural Knee Data

No abstract provided.

Du01, Center For Orthopaedic Biomechanics, Michael D. Harris, Phd, Kevin Shelburne, Phd

Natural Knee Data

No abstract provided.

Probabilistic Musculoskeletal Simulation Methods To Address Intersegmental Dependencies Of The Knee, Hip, And Spine, Casey A. Myers

Electronic Theses and Dissertations

Orthropaedic clinical practice in the area of the knee, hip, and spine has benefited from the concept of regional interdependence, where interventions applied to one region can influence the outcome and function of other regions of the body that may be seemingly unrelated to the applied intervention. An understanding of the biomechanical mechanisms that describe clinical practice involving knee, hip, and spine regional interdependence can improve treatment of a wide range of pathological conditions. Improvement in this area can be particularly impactful on the outcomes of patients with total joint replacement, where pathology and compensatory strategies develop during multi-joint interactions. …

Additives For Heat Transfer Enhancement In High Temperature Thermal Energy Storage Media: Selection And Characterization, Philip D. Myers Jr.

USF Tampa Graduate Theses and Dissertations

Inorganic salts are very promising as high-temperature heat transfer fluids and thermal storage media in solar thermal power production. The dual-tank molten salt storage system, for example, has been demonstrated to be effective for continuous operation in solar power tower plants. In this particular storage regime, however, much of the thermal storage potential of the salts is ignored. Most inorganic salts are characterized by high heats of fusion, so their use as phase-change materials (PCMs) allows for substantially higher energy storage density than their use as sensible heat storage alone. For instance, use of molten sodium-potassium eutectic salt over a …

Evaluation Of School Vip Latrines And User Preferences And Motivations For Adopting Communal Sanitation Technologies In Zwedru, Liberia, Sarah J. Ness

USF Tampa Graduate Theses and Dissertations

This thesis has three objectives as follows: 1) to investigate VIP latrine design and establish if the communal school VIP latrines located on the shared campus of Tubman Wilson Institute (TWI) Junior and Senior High School and J.C. Barlee Elementary School were properly designed and constructed, 2) to explore the user preferences and motivations impacting the adoption of these school latrines, and 3) to develop a framework for factors that influence latrine adoption. These goals were formed by the author in response to her Peace Corps experience working at a high school in Zwedru, Liberia from August 2012 to August …

Bus Rapid Transit (Brt) Toolbox: Brt Person Throughput-Vehicle Congestion Tradeoffs, Li Jingquan, H.-S. Jacob Tsao, Ching-Yao Chan, Kun Zhou, Wei-Bin Zhang

Faculty Publications

This report documents a research effort to understand the current practice and issues associated with Bus Rapid Transit (BRT) planning and deployment. It reviewed the design options incorporated into existing BRT deployments across California and the nation. The project team interviewed practitioners of California Department of Transportation (Caltrans) Districts and transit agencies to understand the BRT project approval decision-making process, the impacts of BRT implementation and the Measures of Effectiveness (MOEs) for transit and non-transit system performance. The studies revealed that though Caltrans and transit agencies do use a similar set of MOEs for the evaluation of BRT projects, the …

A General Intuitive Design Pattern For Optimally Sequencing Treatment Combinations In 2k Factorial Experiment And A Simple Estimation Algorithm, H.-S. Jacob Tsao, Minnie Patel

Faculty Publications

The number of model parameters of a 2k factorial design grows exponentially. When the number of factors is large, numerous higher-order interactions constitute a vast majority of the model parameters while many of them do not exist or are insignificant. The classic methods of fractional factorial designs, Plackett–Burman designs, Taguchi designs, etc. seek an already developed and often cataloged design that fits exactly the problem being tackled or select a design that fits it the most. Most, if not all, of these designs were developed in absence of convenient computation tools and enjoy computational simplicity. The necessary number of treatment …

Non-Invasive Right Ventricular Efficiency Using 4d Flow Mri, Alejandro Roldán-Alzate, Scott Grogan, Heidi Kellihan, Alessandro Bellofiore, Naomi Chesler, Oliver Wieben, Christopher Francois

Faculty Publications

Pulmonary arterial hypertension (PH) is a progressive disease of increased resistance to flow through the lungs, leading to right ventricular (RV) failure [1]. MRI is increasingly used to assess right ventricular (RV) function in PH. RV stroke work (SW) based on invasive pressure and volume measurements, is used to assess ventricular work. Determining RV work from MRI could enable a more complete characterization of RV and PA interactions in PH. The purpose of this study was to non-invasively estimate RV work from simultaneously acquired RV volume (VRV) and pulmonary artery flow (QPA) using a 4D flow-sensitive MRI sequence …

Material Considerations For Development Of 3d Printed Bronchial And Tracheal Stents, Nidah M. Hussain

Theses and Dissertations

Tracheobronchial malacia is a commonly under-diagnosed condition that results in difficulty breathing. The use of a tracheobronchial stent is the best course of treatment for patients whose quality of life has deteriorated due to malacia; unfortunately stents need replacing after issues with inflammation, migration, or eventual stent-breakdown resulting in fistula formation.

The purpose of this thesis is to use three-dimensional (3D) printing technology to improve on existing stents through designing and printing a bioresorbable/biodegradable tracheobronchial stent that can treat tracheobronchial malacia. This was undertaken by testing three biologically favorable materials, type I collagen, polycaprolactone (PCL), and thermoplastic polyurethane (TPU), with …

Design And Development Of A Ventilation Chamber For Testing Efficacy Of Tracheal Stents, Caroline N. Horton

Theses and Dissertations

Tracheobronchial malacia results in a weakening of the tracheal walls, leading to increased difficulty breathing. Stents are used to reopen the lumen of the trachea, however, current models are not personalized to each patient, leading to migration, inflammation, and breakage of the stents. In order to successfully test novel stent designs, a ventilation chamber is needed to recreate the breathing conditions of the body.

The following describes the iterative development of a ventilation chamber, which allows inflation and deflation of lungs via negative pressure ventilation, as representative of an actual body undergoing respiration. Previous work shows that lungs are not …

Design Of Experiments Analysis Of Non-Standard Inputs For The Optimization Of Friction Stir Welding, Ryan Widejko

Theses and Dissertations

The purpose of this study was to use non-standard Design of Experiments (DoE) inputs in Friction Stir Welding (FSW) to deduce relationships between various weld input and response variables. Typically, inputs for FSW DoE are tool rotational speed, welding speed and forge force. In this study, three different input factors were investigated: travel speed, thermal boundary conditions (TBC), and advance per revolution (APR). The experimental design included a full factorial with each factor at two levels plus two centerpoint runs. Response variables included weld temperature, microstructure, hardness, power, weld energy, and in plane forces.

An investigation of the effect of …

An Investigation Into Quasi-Tunable Rf Passive Circuit Design, Terry L. Moss

Theses and Dissertations

Modern wireless electronic circuit design is continually challenged by the needs to reduce circuit size, and to also function reliably with lower power levels. To that end, two aspects of RFIC circuit design and technology have gained great interest, i.e. RF MEMS switching technology, and RF MEMS passive component development. MEMS (Micro-Electromechanical Systems) technology, originally developed for the defense industry, has been in development since the 1970s, and today enjoys wide range of utilization, from the defense industry to the automotive industry. Spiral inductors used in RFIC circuits, e.g. silicon technology, are ubiquitous in wireless RFIC applications. The tradeoff with …

Brand Positioning Map And Analysis Using Web Scraping And Advertisement Analysis, Surya Bhatt

Theses and Dissertations

There’s a significant increase in online consumer forums. When customers set out to buy a product they use these forums to form an opinion. Our research focuses on comparing Brand positioning maps based on consumer reviews. We also analyse the impact of advertisements and expert reviews. Our goal is to show that combining consumer reviews with ads and electronic media will help us analyze the effectiveness of advertising on brand positioning maps. This approach shall also help us in making association graphs for a brand using words of perception/opinion associated with that brand/product. Which may in turn assist companies in …

Selective Synthesis And Characterization Of Single-Site Hy Zeolite-Supported Rhodium Complexes And Their Use As Catalysts For Ethylene Hydrogenation And Dimerization, Konstantin Khivantsev

Theses and Dissertations

Single-site Rh(CO)2, Rh(C2H4)2 and Rh(NO)2 complexes anchored on various dealuminated HY zeolites can be used as precursors for the selective surface mediated synthesis of well-defined site-isolated Rh(CO)(H)x complexes. DFT calculations and D2 isotope exchange experiments provide strong evidence for the formation of a family of site isolated mononuclear rhodium carbonyl hydride complexes (including the first examples of RhH complexes with undissociated H2 ligands): Rh(CO)(H2), Rh(CO)(H)2, and Rh(CO)(H). The fraction of each individual complex formed varies significantly with the Si/Al ratio of the zeolite and the nature of the precursor used.

HY zeolite-supported mononuclear Rh(CO)2 complexes are remarkably active in ethylene …

Fabrication And Characterization Of Graphene Based Biocompatible Ion-Sensitive Field Effect Transistor (Isfet), Rina Patel

Theses and Dissertations

Graphene, a two-dimensional material with a high surface to volume ratio, has drawn extensive research enthusiasm for applications in the field of electronic sensors. The special material properties that make graphene a highly promising material include its biocompatibility, very high mobility, low 1/f and thermal noise, modulation of carrier concentration and fermi level by electrical, optical, and chemical means. To exploit these properties for practical applications a large area high quality graphene, transferred on appropriate substrates, is required. In this work, high quality single monolayer graphene (determined from Raman spectroscopy) has been synthesized by chemical vapor deposition (CVD) technique for …

Technology Development And Characterization Of Aiinn/Gan Hemts For High Power Application, Mahbuba Sultana

Theses and Dissertations

AlInN has attracted much attention only recently as a material due to its unique and superior material properties, which is however known to be difficult to be grown among the III-nitride ternary compounds. The electrons confined at the heterointerface of coherently grown AlInN on GaN buffer layers determine crucial electronic properties. This dissertation has been designed targeting the lattice matched AlInN/GaN investigation with very detail to optimize the design, fabrication process, and electronic properties to realize AlInN/GaN HEMTs. Each single step of this process was optimized in order to improve device performance.

The work started with establishing the main features …

Engineered 3d Microenvironments To Direct Osteogenic Differentiation And Modulate Inflammation, Katherine Elizabeth Rutledge

Theses and Dissertations

Current methods of treating critical size bone defects (CSDs) include autografts and allografts, however both present major limitations including donor-site morbidity, risk of disease transmission, and immune-rejection. Tissue engineering provides a promising alternative to circumvent these shortcomings through the use of stem cells, three dimensional (3D) scaffolds, and growth factors. Cells receive signals from their microenvironment that determine cell phenotype, and a combination of physical cues and chemical factors is thought to have the most profound influence on stem cell behavior. A major focus of tissue engineering strategies is scaffold design to recapitulate in vivo microenvironmental architecture to direct stem …

Drilled Shaft Skin Resistance Design In The Cooper Marl, William J. Gieser

Theses and Dissertations

As drilled shafts have become a more popular foundation type in the Charleston, South Carolina area, there has been an ongoing goal of optimizing drilled shaft design while maintaining the structural integrity of the foundation. In the Charleston area, the primary bearing stratum for deep foundations is the Cooper Marl, a calcareous Oligocene formation. Research performed from 2002 to 2004 on load test data from drilled shafts constructed in the Cooper Marl and soil properties from three test sites for the Cooper River Bridge explored the relationship between the measured skin resistance and geotechnical properties. In the 15 years since …

Iii-V Nitride Based Microcantilever Heaters For Unique Multimodal Detection Of Volatile Organic Compounds At Low Temperature, Ifat Jahangir

Theses and Dissertations

Detection of volatile organic compounds (VOCs), which are widely used in industrial processes and household products, is very important due to significant health hazards associated with them. VOCs are commonly detected using photo-ionization detectors (PIDs), suspended hot bead pellistors, or heated metal oxide semiconductor functionalization layers. However, these techniques used for detecting VOCs often suffer from one or more of the following issues - high power consumption, limited selectivity, complicated functionalization technique and expensive characterization tools. On the other hand, microcantilevers offer excellent avenues for molecular sensing that arises out of their high sensitivity to various physical parameter changes induced …

Planning Freeform Extrusion Fabrication Processes With Consideration Of Horizontal Staircase Effect, Amir Ghazanfari, Wenbin Li, Ming Leu, Robert Landers

Faculty Publications, Mechanical Engineering

An algorithm has been developed to estimate the “horizontal” staircase effect and a technique is proposed to reduce this type of geometrical error for freeform extrusion fabrication processes of 3D “solid” parts. The adaptive rastering technique, proposed in this paper, analyzes the geometry of each layer and changes the width of each line of the raster adaptively in order to reduce the staircase error and increase the productivity simultaneously. For each line, the maximum width that results in a staircase error smaller than a predefined threshold is determined for decreasing the fabrication time or increasing the dimensional accuracy, or both. …