Engineering Commons^™

Nanomechanical And Morphological Characterization Of Tungsten Trioxide (Wo3) Thin Films Grown By Atomic Layer Deposition, M. A. Mamun, K. Zhang, H. Baumgart, A. A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

This study investigates the nanomechanical properties and surface morphology of tungsten oxide WO₃thin films deposited on p-type Si(100) substrates using atomic layer deposition (ALD) technology with 2000 ALD deposition cycles at a growth temperature of 300°C and annealed at different temperatures. The samples were further furnace annealed at 500, 600 and 700°C for 60 min. The influence of the deposition process on the structure and properties of the WO₃ films is discussed, presented and correlated to the characteristic features of the ALD technique. The results depict significant difference in the hardness and modulus measurements between the as …

Development Of The Framework For A Self-Assessment Tool To Assess The Effectiveness Of Reporting Within A Safety Critical Industry, Maria Chiara Leva, Samuel Cromie, Ewan Douglas

Conference papers

There is currently a large amount of literature to provide guidance on the areas that should be considered when developing a reporting system. However there is no current methodology of monitoring the performance and compliance of a reporting system.This paper outlines the development process for a Self-Assessment Tool (SAT) assessing the effectiveness of safety reporting within safety critical activities. The paper outlines the need for such a self-assessment tool, the areas that will be assessed (and the rationale be-hind their selection), selection of the platform and finally the planned validation exercises for the paper

The Identification Of Assessment Criteria For A Safety Reporting Self-Assessment Tool, Maria Chiara Leva, Samuel Cromie, Ewan Douglas

Conference papers

This paper describes the assessment criteria that have been identified for use within a self-assessment tool for risk reporting within an industrial context. An in-depth review of the available literature was carried out exposing the criteria discussed within this paper. The criteria target all areas of reporting from the design of the reporting interface to the cultural considerations and initiatives. These criteria will be refined and weighted using industrial case study experience and then developed into the full self-assessment tool.

Climate Change Implications For Health-Care Waste Incineration Trends During Emergency Situations, Emilia Mmbando Raila

Walden Dissertations and Doctoral Studies

Healthcare waste (HCW) incineration practices in the global South countries are among the major sources of black carbon (BC) emissions or smoke. This study analyzes HCW incineration trends during emergency situations and smoke from HCW incineration processes in Haiti. The study was prompted by the current arguments about the climate change and the growing health effects associated with BC emissions. The conceptual framework was based on both adverse health effects from BC emissions exposure and climate change potential of BC emissions. Therefore, the goal was to determine whether cardboard HCW sharps containers emit lower BC emissions to the atmosphere during …

Road Management System And Road Safety In Uganda, Paul Gudoi Zanule

Walden Dissertations and Doctoral Studies

Traffic collisions cost Uganda millions of dollars each year. The purpose of this descriptive case study was to describe the strategies and processes needed to implement a road management system. Such a system would significantly reduce the fatalities and accidents in Uganda, improve the transportation within Kampala's business district, and increase business profitability. Three conceptual theories framed the research study: management theory, strategic management theory, and criminology theory. Using a snowball sampling strategy, data were collected from open-ended interviews, questionnaires, observations, and archived documents from 20 administrative participants in the government and organizational leaders involved in the transport operations and …

A Comparison Of Combined Overlap Block Fuzzy Cognitive Maps (Cobfcm) And Combined Overlap Block Neutrosophic Cognitive Map (Cobncm) In Finding The Hidden Patterns And Indeterminacies In Psychological Causal Models: Case Study Of Adhd, Hojjatollah Farahani, Florentin Smarandache, Lihshing Leigh Wang

Branch Mathematics and Statistics Faculty and Staff Publications

In spite of researchers’ concerns to find causalities, reviewing the literature of psychological studies one may argue that the classical statistical methods applied in order to find causalities are unable to find uncertainty and indeterminacies of the relationships between concepts.

In this paper, we introduce two methods to find effective solutions by identifying “hidden” patterns in the patients’ cognitive maps. Combined Overlap Block Fuzzy Cognitive Map (COBFCM) and Combined Overlap Block Neutrosophic Map (COBNCM) are effective when the number of concepts can be grouped and are large in numbers. In the first section, we introduce COBFCM, COBNCM, their applications, and …

Nebraska Summary: S1018 Massey Ferguson 7724, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Investigation Of Gate Dielectric Materials And Dielectric/Silicon Interfaces For Metal Oxide Semiconductor Devices, Lei Han

Theses and Dissertations--Electrical and Computer Engineering

The progress of the silicon-based complementary-metal-oxide-semiconductor (CMOS) technology is mainly contributed to the scaling of the individual component. After decades of development, the scaling trend is approaching to its limitation, and there is urgent needs for the innovations of the materials and structures of the MOS devices, in order to postpone the end of the scaling. Atomic layer deposition (ALD) provides precise control of the deposited thin film at the atomic scale, and has wide application not only in the MOS technology, but also in other nanostructures. In this dissertation, I study rapid thermal processing (RTP) treatment of thermally grown …

Fault Section Identification For Power Distribution Systems Using Online Measurements, Jie Chen

Theses and Dissertations--Electrical and Computer Engineering

Fault location is very important for distribution systems, and quickly identifying the fault and restoring the system can help reduce the outage time and make the system more reliable. In this thesis, a method for locating faults on distribution systems is introduced to quickly identify the faulted feeder sections by using the overcurrent information from the switches in the system. Fuzzy logic is utilized. The proposed method can quickly and accurately locate faulted sections with different fault locations, fault types and fault resistances. The method is applicable to cases with single-faults or multi-faults, and is applicable to networks with multi-sources. …

Hybrid Single And Dual Pattern Structured Light Illumination, Minghao Wang

Theses and Dissertations--Electrical and Computer Engineering

Structured Light Illumination is a widely used 3D shape measurement technique in non-contact surface scanning. Multi-pattern based Structured Light Illumination methods reconstruct 3-D surface with high accuracy, but are sensitive to object motion during the pattern projection and the speed of scanning process is relatively long. To reduce this sensitivity, single pattern techniques are developed to achieve a high speed scanning process, such as Composite Pattern (CP) and Modified Composite Pattern (MCP) technique. However, most of single patter techniques have a significant banding artifact and sacrifice the accuracy. We focus on developing SLI techniques can achieve both high speed, high …

A Methodology Of Spice Simulation To Extract Sram Setup And Hold Timing Parameters Based On Dff Delay Degradation, Xiaowei Zhang

Theses and Dissertations--Electrical and Computer Engineering

SRAM is a significant component in high speed computer design, which serves mainly as high speed storage elements like register files in microprocessors, or the interface like multiple-level caches between high speed processing elements and low speed peripherals. One method to design the SRAM is to use commercial memory compiler. Such compiler can generate different density/speed SRAM designs with single/dual/multiple ports to fulfill design purpose. There are discrepancy of the SRAM timing parameters between extracted layout netlist SPICE simulation vs. equation-based Liberty file (.lib) by a commercial memory compiler. This compiler takes spec values as its input and uses them …

Design Of Energy Storage Controls Using Genetic Algorithms For Stochastic Problems, Si Chen

Theses and Dissertations--Electrical and Computer Engineering

A successful power system in military applications (warship, aircraft, armored vehicle etc.) must operate acceptably under a wide range of conditions involving different loading configurations; it must maintain war fighting ability and recover quickly and stably after being damaged. The introduction of energy storage for the power system of an electric warship integrated engineering plant (IEP) may increase the availability and survivability of the electrical power under these conditions. Herein, the problem of energy storage control is addressed in terms of maximizing the average performance. A notional medium-voltage dc system is used as the system model in the study. A …

Test 2122: New Holland T8.320, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2108: John Deere 9420r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Fatigue Shaft Design Verification For Bending And Torsion, Edward Osakue, Lucky Anetor, Christopher Odetunde

Faculty Publications

A design verification study of some shafts based on a probabilistic approach using the Gerber fatigue failure rule is presented. The shafts are subjected to combined bending and torsional loads. The design model parameters are considered as random variables characterized by mean values and coefficients of variation (covs). The coefficient of variation of a design parameter is obtained by using first order Taylor series expansion for strength and stress in a stress-based fatigue design. A reliability factor is defined and related to the covs of the design parameters and a failure probability. This study shows that deterministic engineering models can …

Continuous Monitoring Of Movement In Patients With Parkinson's Disease Using Inertial Sensors, Mahmoud Ahmed El-Gohary, Sean Pearson, James Mcnames, Martina Mancini, Fay Horak

Electrical and Computer Engineering Faculty Publications and Presentations

Gait impairment is a hallmark of Parkinson's disease (PD). The assessment of gait and balance in the clinic may not adequately reflect mobility in daily life. It is often reported that patients with PD walk better when they are examined in an outpatient clinic or in a research laboratory than at home. Continuous monitoring of mobility during spontaneous daily activities may provide clinicians and patients with objective measures of the quality of their mobility. We show that continuous monitoring of spontaneous gait with wearable inertial sensors during daily activities is feasible for patients with PD. We tested 13 patients with …

Life Cycle Assessment (Lca) Of Tourism Activities, Kayla Santello

Honors Theses and Capstones

Abstract— Tourism, like other developed industries is a commerce that requires energy inputs and yields outputs with significant effects on the environment. However a comprehensive study examining the life cycle impact associated with each tourism component including transportation, accommodation, food services, and recreation is still lacking. Therefore a search of previous tourism life cycle studies was carried out and ten studies were further investigated. Indicators, assessment approaches, and system boundaries of these previous studies were assessed. Then the outcomes were normalized and compared in order to obtain ranges for the four components of tourism. It was found that energy intensity …

Offshore Turbine Arrays: Numerical Modeling And Experimental Validation, Thomas Kroll, William Hall, Ian Gagnon

Honors Theses and Capstones

The interaction between wind turbines in a large wind farm needs to be better understood to reduce array losses and improve energy production. A numerical test bed for an array of offshore wind turbines was developed in the open-source computational fluid dynamics (CFD) framework OpenFOAM. It provides a computational tool which can be used in combination with physical model turbine array studies in the Flow Physics Facility (FPF) at UNH as well as other test facilities.

Turbines were modeled as actuator disks with turbulence sources to reduce computational cost. Both k-ϵ and k-ω SST turbulence models were utilized to capture …

Pack Factor Measurements For Corn In Grain Storage Bins, Rumela Bhadra, Aaron P. Turner, Mark E. Casada, Michael D. Montross, Sidney A. Thompson, Josephine M. Boac, Samuel G. Mcneill, Ronaldo G. Maghirang

Biosystems and Agricultural Engineering Faculty Publications

Shelled yellow corn is commonly stored in concrete or corrugated steel bins. Granular materials compact under their own weight, primarily due to particle rearrangement, leading to an increase in bulk density and a change in volume when stored. Reliable grain pack factors are needed to estimate storage capacities and to accurately monitor grain inventories. A science-based model (WPACKING) of pack factors is available that uses the differential form of Janssen's equation and takes into account the variation in density caused by pressure variation with height and moisture content of the grain and accounts for the effects of grain type, test …

An Adaptive Physical- And Link Layer For Narrowband Mobile Ad-Hoc Networks, Mathias Dehm

Theses

Search and Rescue (SAR) missions require robust ad-hoc networks especially in situations where existing wired or cellular networks have been damaged or are not available. Here, a promising SAR communications technology is a Mobile Ad-hoc Networks (MANETs). However, development of systems is challenging due to bandwidth constraints, various application services, high mobility and harsh environments leading to unstable wireless connections.

Throughout this thesis, a prototype of a physical- and link layer is developed which satisfies the criteria for communication services in SAR missions.

This work includes three major contributions:

The first contribution is a single-carrier narrowband physical layer. The transmission …

An Experimental Investigation On Friction And Scuffing Failure Of Lubricated Point Contacts, Sai Goutham Soma

Browse all Theses and Dissertations

Scuffing failure is a catastrophic thermal failure mode induced by the extreme surface temperature of the contacting components. As two mechanical elements roll against each other with high sliding motion, the frictional heat flux elevates the surface temperature to exceed the critical limit, resulting in the welding of the surfaces. The relative motion then tears the welded surfaces apart, causing the damage. Scuffing failure has been an important failure mode for rolling machine elements such as bearings and gears in aerospace applications, owing to the very high operating speeds. Recently, this failure mode has extended to the automotive field, where …

Vitamin D Receptor And 1Α, 25-Dihydroxyvitamin D3 Mediated Regulation Of Δnp63Α, Hill Tremayne Natasha

Browse all Theses and Dissertations

1alpha, 25-dihydroxyvitamin D3 (VD3), the ligand for the Vitamin D Receptor (VDR), functions to both inhibit cell growth and promote cell survival. High-dose VD3 is being utilized as a cancer preventive therapy for melanoma, breast and colorectal cancers, without a complete understanding of VD3/VDR signaling. DeltaNp63alpha, considered to be a proto-oncogene, is overexpressed in non-melanoma skin cancers (NMSCs), induces VDR gene expression and promotes keratinocyte proliferation, and may serve to exacerbate non-melanoma skin cancer. The objective of this dissertation was to determine whether VDR/VD3 signaling promotes keratinocyte proliferation by up-regulating DeltaNp63alpha. I showed that VDR increases DeltaNp63alpha expression at both …

Whole-Lake Primary Production Calculator, Colin D. Leong

Browse all Theses and Dissertations

This work describes an implementation of a model for estimation of both benthic and phytoplanktonic primary production in lakes. The web application makes use of interpolation techniques to allow estimates of primary production using values for photosynthesis/irradiance parameters at only 5 depths. These estimates compare favorably in accuracy with estimates using values listed at over one hundred depths. Validation of the implementation was done by comparison with primary production results from the Northern Temperate Lakes Long Term Ecological Research database.

Left Ventricle Volume Reconstruction To Minimize Scanning Time: Slice-Fitting Method, Prateek Kalra

Browse all Theses and Dissertations

Assessment of left ventricle volume is usually done for diagnosis and prognosis of heart diseases. Slice-summation method is a standard method used to compute left ventricle volume where region of interest from several short axis (SA) slices are added. There are some limitations to this method, however. It requires short-axis slices to be taken parallel to the mitral valve plane from the base to apex. Moreover, scanning several short-axis slices is a tedious and time consuming process especially for studies that require several hundreds datasets. There are some existing methods to reconstruct left ventricle volume but most of them depend …

Split Ring Resonator Design For Agricultural Based Applications, Joshua David Compaleo

Browse all Theses and Dissertations

Recent advances with manufactured electromagnetic materials known as metamaterials are paving the way to use microwave technology in agricultural development and harvesting. It has been proposed that split ring resonators could be placed on the surface of fruit or vegetables such that the resonant behavior may be monitored and used to estimate the ripeness level. The method is non-destructive and could enable monitoring of large quantities of produce or even be tailored to hand-held devices for consumers. However, the understanding of corresponding changes in the proposed device's resonant behaviors and ripeness levels are limited. In addition, fruit and vegetables are …

Fiber Compaction And Wetout In Tapered Resin Injection Pultrusion Manufacturing, Naveen Babu Masuram

Electronic Theses and Dissertations

Pultrusion is a continuous process for manufacturing composite materials with constant cross section. Reinforced fibers are pulled through a resin, possibly folloby a separate injection chamber preforming system, and into a heated die, where the resin undergoes complete wetout. Thus the required pultruded composite is obtained in the desired profile. The main objective of this research is to present a numerical model employing the finite volume technique to simulate the resin flow in a tapered injection chamber through the fiber reinforcement when compaction of the fiber reinforcement is taken into account. The numerical model predicts the impact of design and …

Some Experimental Investigation On Effect Of Light And Vibration On Nano Coated Piezo For Energy Harvesting, Abhay Sharma

Electronic Theses and Dissertations

PZT is a promising piezoelectric ceramic material which has a wide range of applications in a variety of fields such as acoustic sensors and transducers, electrical switches, medical instrumentation, artificial sensitive skin in robotics, automotive detection on roads, nondestructive testing , structural health monitoring and as a biocompatible material. In this research a cantilever based multi energy harvester was developed to maximize the power output of PZT sensor. Nano mixtures containing graphene, ferrofluid nanoparticle (FNP) and ZnO nano particles were used to enhance the piezoelectric and photovoltaic output of the sensor. The samples were tested under different energy conditions to …

Carbon Dioxide Capture With Amine Functionlized Graphene Oxide, Renee Zeleszki

Electronic Theses and Dissertations

Abstract: amine functionalized graphene oxide was used as sorbent in order to achieve carbon dioxide capture. In this study, micro size graphite flakes was prepared according to modified hummers method and "hummers' method with additional kmno4." Graphene oxide was then functionalized with ethylenediamine (eda). Different purification methods for graphene oxide were studied as well as different functionalization method times. Graphite oxide and functionalized graphene oxide has been analyzed with fourier transform infrared spectroscopy (ftir) for chemical structure. Thermal gravimetric analysis (tga) was used to test co2 capture capacity. Functionalized graphene oxide that has been purified with 30 washes via centrifuge …

Computational Finite Element Analysis Of Extreme Loading Response Of Structural Insulated Panel (Sip) Building Subsystems, Kimberly Anne Tanner

Electronic Theses and Dissertations

In the reconstruction after Hurricane Katrina, the Mississippi Emergency Management Agency (mema) investigated of the possibility of utilizing structural insulated panel (sip) construction for hurricane "cottages" that would be resistant to a category 3 hurricane through a joint project with a local architect, Bruce Tolar, and FMS Engineering, LLC, Mobile, Alabama. The connections between the sip panels, including a cam-locking device comto sip panel construction, were identified as vulnerable under high velocity wind loads. At that time, there were no published guidelines for performing a computational finite element analysis of the sip system, and thus it was not possible to …

Empirical Modeling Of Piping Along Mississippi River Levees In Southwestern Illinois, Rebecca F. Shields

Electronic Theses and Dissertations

No abstract provided.