Engineering Commons^™

A Modified Initiation And Cut Profile Study Of The 10500 Grain Per Foot Linear Shaped Charge, Matthew Ortel

Masters Theses

"A 10,500 grain per foot (gr/ft.) linear shaped charge (LSC) was developed to cut targets that were too thick for smaller LSC. The manufacturer observed shallower penetration from the 10,500 gr/ft. LSC than was expected. This prompted investigations to uncover the cause of the perceived reduced performance.

A study performed at the Missouri University of Science and Technology changed the initiation method of the 10,500 gr/ft. charge to increase the cut performance of the charge. A modified two point, single end initiation method was devised and tested. This initiation method was termed "dual initiation" and focused on creating a planar …

Quantifying Economic Benefits For Rail Infrastructure Projects, Akhilesh Ojha

Masters Theses

"Investment in rail infrastructure is necessary to maintain existing service and to cater for future growth in freight and passenger services. Many communities have realized the importance of investment in rail infrastructure projects and set up goals and visions to achieve economic development through investing in such projects. Due to limited funds available, communities have to select a single or very few projects from a variety of projects. It is very critical that right projects must be selected at the right time for a community to realize economic development. The limited methods for quantifying the economic benefits to the stakeholders …

Evaluation Of Prosper For Modeling Long Lateral Gas Well Productivity In Toe Up, Toe Down, Horizontal Well Geometry, Abdussalam Mahmoud Mohamed

Masters Theses

"Most horizontal wells are not truly horizontal and may be drilled 'toe-up' or 'toe-down' to follow geological formations or in an attempt to keep the well from loading up. Challenges in directional drilling may also lead to horizontal gas wells with undulating wellbore profiles. This wellbore profile creates natural traps for heavy fluids in the lows and light fluid in the highs, which may result in chocked production. Hence, there is an interest in determining the best wellbore trajectory - toe-up, horizontal, or toe-down - for well unloading.

This study evaluates the capability of the well productivity software PROSPER to …

Computer Vision Libraries For Trailer Truck Testbed Using Open Source Computer Vision Libraries, Krishnan Raghavan

Masters Theses

"Computer Vision is a field that aims at understanding and analyzing images from the real world to produce numerical and symbolical data. It is a first step at duplicating the capabilities of human vision by electronically understanding the image and perceiving its features. This work aims at providing some of the features of a human eye to a trailer truck. These features include getting a 3D wireframe from continuous images and prediction of the next position of the objects in view, while the truck is moving.

The thesis has been divided into 3 sections. First section is acquiring images in …

Use On Multinomial Logistic Regression In Work Zone Crash Analysis For Missouri Work Zones, Paul Robin

Masters Theses

"This study focuses on the use of statistical data analysis procedures in identifying factors which affect the severity of crashes in work zones. Work zones are unsafe for the traffic passing through as well as the workers. Multinomial Logistic Regression has been used to analyse Missouri work zone crash data to identify significant factors which affect the severity of crashes. This particular type of regression analysis was used due to the mixed nature of data. Multinomial regression was used to compare crashes with severity Property Damage Only against crashes with Minor Injuries and Disabling Injuries/ Fatal. The factors considered were …

Hedge Fund Replication Using A Strategy Specific Modeling Approach, Sujit Subhash

Masters Theses

"Institutional investors and wealthy individuals have in the past allocated a significant portion of their portfolios to hedge funds with the expectation of unconditional and uncorrelated returns to the market. However, the financial crisis of 2008 has heightened investor sensitivity to the high fees, illiquidity, and lockup periods typically associated with hedge funds. Hedge fund indexes showing excellent returns and low volatility contain funds that are closed to new investments, while the performance of investable funds have been shown to be inferior to their non-investable counterparts. The lack of transparency and extreme variation in the performance of hedge funds make …

"Green" On-Chip Inductors In Three-Dimensional Integrated Circuits, Umamaheswara Rao Tida

Masters Theses

"This thesis focuses on the technique for the improvement of quality factor and inductance of the TSV inductors and then on the utilization of TSV inductors in various on-chip applications such as DC-DC converter and resonant clocking. Through-silicon-vias (TSVs) are the enabling technique for three-dimensional integrated circuits (3D ICs). However, their large area significantly reduces the benefits that can be obtained by 3D ICs. On the other hand, a major limiting factor for the implementation of many on-chip circuits such as DC-DC converters and resonant clocking is the large area overhead induced by spiral inductors. Several works have been proposed …

Measurements And Transient Multistep Outflow Simulation Of Soil-Water Characteristic Curve For Soils Modified With Biopolymers, Xiaoyi Zhao

Masters Theses

"In recent decades, biopolymers have shown promising applications in soil modification due to its environmental friendly nature. Most of the studies, however, focused on mechanical properties at saturated or unsaturated conditions. The study on unsaturated soil behaviors under controlled pore air and pore water pressures were limited. Soil-water characteristic curve (SWCC), relating water content with matric suction is a key property to evaluate unsaturated soils. With SWCC, other soil properties, such as hydraulic conductivity and shear strength can be estimated. In this study, SWCC of sands modified with different biopolymers were measured with both Tempe cell and Fredlund SWCC device. …

Computation Of Cross-Talk Alignment By Mixed Integer Linear Programming, Qifeng Chen

Masters Theses

"Noise analysis has been an important and difficult part of design flow of very large-scale integrated (VLSI) systems in many years. In this thesis, the problem of signal alignment resulting in possible maximum peak interconnect coupling noise and propose a variation aware technique for computing combined noise pulse taking into account timing constraints on signal transitions has been discussed. This work shows that the worst noise alignment algorithm can be formulated as mixed integer programming (MLIP) problem both in deterministic window cases and variational window cases. For deterministic window cases, it is assumed that timing windows are given for each …

Test Development To Determine The Feasibility Of Rubber Tractor Treads For Use As Blasting Mats, Matthew Kurtis Coy

Masters Theses

"The objective of this thesis was to determine if rubber tractor treads could be used as an alternative material for blasting mats. These treads are made from steel cable and vulcanized rubber and are very tough. However, once they reach the end of their life on mobile equipment, they are destined for a landfill, or dump site because they are too tough to recycle. A potential alternative use for them is as blasting mats.

An examination of existing mat designs was conducted to better understand the matting methods used by the blasting industry today, to learn from those designs allow …

Fabrication Of Out-Of-Autoclave Bismaleimide Based Composite Laminates With Embedded Fiber Optic Sensors, Sudharshan Anandan

Masters Theses

"Composites are becoming the material of choice in applications where weight savings are critical, like aerospace structures. The common composites used are- Carbon/Epoxy and Carbon/Bismaleimide (BMI). BMI based systems are preferred in applications which involve operating temperatures higher than conventional epoxies. Carbon/BMI laminates are traditionally fabricated in an autoclave, which is associated with high operating costs. In this work, a low cost out of autoclave (OOA) process is evaluated. It is desirable to have BMI OOA prepreg systems cure at reasonably low temperatures with sufficient degree of cure and green strength to maintain rigidity for subsequent freestanding post cure Carbon/BMI …

Thermodynamics And Crystallography Of The Γ→Ε→Α' Transformation In Femnalsic Steels, Scott Thomas Pisarik

Masters Theses

"FeMnAlSiC steels which exhibit two-stage transformation induced plasticity (TRIP) behavior characterized by the γ→ε→α' dual stage martensitic transformation promise to take a leading role in the development of 3rd generation advanced high strength steels. The crystallographic orientation relationship of the γ→α' and γ→ε athermal martensitic transformations in these steels has been determined as the Kurdjumov-Sachs and the Shoji-Nishiyama, respectively. Six crystallographic variants of α-martensite consisting of three twin-related variant pairs were observed in ε- bands. A planar parallelism of {0001}ε || {110}α' and a directional relation of α' lying within 1⁰ of ε existed for these variants. Two regular solution …

Feasibility Study Of A Two-Fluid Small Modular Molten Salt Reactor With In Core Heat Removal Capability, Brandon James Lahmann

Masters Theses

"A feasibility study of a two-fluid small modular molten salt reactor (MSR) with in core heat removal was performed. The initial fuel block dimension for the configuration was based on the Fuji MSR. The fuel was a mixed fluoride salt of density 3.25 g/cc, composed of 71 LiF - 16 BeF₂ - 12 ThF₄- 1 ²³³UF₄ molar percentages. The coolant salt was Li₄(FLiBe) of density 1.94 g/cc. The work set out to establish whether or not such a reactor is thermodynamically feasible when optimized for various neutronics parameters. A Java based API was …

Performance Analysis Of Cutting Graphite-Epoxy Composite Using A 90,000 Psi Abrasive Waterjet, Aiswarya Choppali

Masters Theses

"Graphite-epoxy composites are being widely used in many aerospace and structural applications because of their properties: which include lighter weight, higher strength to weight ratio and a greater flexibility in design. However, the inherent anisotropy of these composites makes it difficult to machine them using conventional methods. To overcome the major issues that develop with conventional machining such as fiber pull out, delamination, heat generation and high tooling costs, an effort is herein made to study abrasive waterjet machining of composites. An abrasive waterjet is used to cut 1" thick graphite epoxy composites based on baseline data obtained from the …

A Driving Simulator Study To Evaluate The Impact Of Portable Changeable Message Signs (Pcms) On Driver Speed Characteristics, Bharath Kolar Venkat

Masters Theses

"This research project examined the effects of sequential Portable Changeable Message Signs (PCMS) on driver behavior in work zones. PCMS are temporary traffic control (TTC) devices, part of Intelligent Transportation Systems, which supplement static signs to provide advance warning and real-time information to drivers. Text and number based messages are displayed on the PCMS for which detailed evaluation has not been carried out before. This research fills this gap using a driving simulator (DS) supplemented by objective and subjective surveys. A work zone on I-44 in rural Missouri was replicated in the DS using video recordings and GIS (Geographical Information …

Interleaved Coupled-Inductor Boost Converter With Multiplier Cell And Passive Lossless Clamp, Stephen C. Moerer

Masters Theses

"As photovoltaic panels become a more dominant technology used to produce electrical power, more efficient and efficacious solutions are needed to convert this electrical power to a useable form. Solar microconverters, which are used to convert a single panel's power, effectively overcome issues such as shading and panel-specific maximum power point tracking associated with traditional solar converters which use several panels in series. This thesis discusses a high gain DC-DC converter for incorporating single low-voltage solar panels to a distribution level voltage present in a DC microgrid. To do this, a converter was developed using coupled inductors and a capacitor-diode …

Cable Discharge Events (Cde) -- A Modeling And Simulation Perspective, Viswa Pilla

Masters Theses

"Cable discharge events (CDE) typically occur when a charged cable is connected to an electronic device. Several CDE damages in Ethernet LAN and USB communication interface equipment are reported by the IC manufacturers. CDE differs from other types of ESD such as human body model (HBM), charged device model (CDM) and IEC 61000-4-2 mainly due to faster rise times, longer pulse widths and higher peak currents. Various factors such as cable geometries, charging and discharging mechanisms, and load conditions influence CDE. Several researchers have developed some measurement techniques to understand CDE waveforms. However, there is little information regarding its modeling …

Design And Implementation Of Two Non-Isolated High Gain Dc-Dc Converters, Huawei Yang

Masters Theses

"In most solar energy systems, the output voltage of a photovoltaic panel is usually between 20 to 40 Vdc. In order to interface the panels to a 400 Vdc bus, a high voltage gain dc-dc converter is required.

This thesis starts with analyzing and simulating several topologies that have been already introduced for this application. The voltage gain and efficiency are investigated analytically. A hardware prototype of one of the existing topologies, the interleaved boost converter with voltage multiplier cell, has been developed. Finally, a new topology with a higher voltage transfer ratio is proposed and its experimental results are …

Economic And Environmental Comparison Of Different Ordering Policies For An Integrated Inventory Control And Supplier Selection Problem, Sepideh Almasi Monfared

Masters Theses

"This study analyzes an integrated inventory control and supplier selection problem in stochastic demand environment under carbon emissions regulations. In particular, a continuous review inventory model with multiple suppliers is investigated under carbon taxing and carbon trading regulations. We analyze and compare the optimal supplier selection and order splitting decisions with single sourcing and two alternative delivery structures for multi-sourcing, namely, sequential ordering and sequential delivery. For each of the three ordering policies, a solution method is proposed and these policies are compared in terms of their economic as well as environmental performances. A numerical study is conducted to demonstrate …

Uterine Cervical Cancer Histology Image Feature Extraction And Classification, Koyel Banerjee

Masters Theses

"The current study presents the investigation and development of image processing, computational intelligence, fuzzy logic, and statistical techniques for different types of data fusion for a varied range of applications. Raw data, decision level and feature level fusion techniques are explored for detection of pre Cervical cancer (CIN) grades from digital histology images of the cervical epithelium tissues.

In previous research, an automated, localized, fusion-based approach was investigated for classifying squamous epithelium into Normal, CIN1, CIN2, and CIN3 grades of cervical intraepithelial neoplasia (CIN) based on image analysis. The approach included medial axis determination, vertical segment partitioning as medial axis …

Performance Evaluation Of Coaxial Horizontal Axis Hydrokinetic Turbines System, Abdulaziz M. Abutunis

Masters Theses

"Hydrokinetic energy technologies are emerging as a viable solution for renewable power generation. Unlike conventional hydropower turbines, hydrokinetic turbines are environmentally friendly; they operate at zero-head, and do not need dams to preserve the water. Unfortunately, they have a low efficiency which makes their design a challenging task. This work was focused on the hydrodynamic performance of horizontal axis hydrokinetic turbines (HAHkTs) under different turbine arrangements and flow conditions.

It was undertaken in an effort to improve the efficiency of small HAHkTs that harness a river's kinetic energy. Four sets of experiments were performed in a water tunnel to investigate …

Fabrication Of Glass Fiber-Reinforced Transparent Composites Using Vacuum Assisted Resin Transfer Molding Process, Gregory A. Taylor

Masters Theses

"The most commonly used transparent material is glass. Traditionally, glass is not desired for applications involving a low weight material while preserving high strength such as aerospace and military applications where armor must also be transparent. Some applications may include aircraft canopies and other vehicle windows. Development of a reliable transparent composite would fill a need for many of these applications where a transparent structure must both be strong and lightweight. A transparent polymer reinforced with a glass fiber fabric is a viable solution. To ensure transparency, both fiber and matrix must match in refractive index.

In the present work, …

Numerical Analysis Of Thermal Stress And Deformation In Multi-Layer Laser Metal Deposition Process, Heng Liu

Masters Theses

"Direct metal deposition (DMD) has gained increasing attention in the area of rapid manufacturing and repair. It has demonstrated the ability to produce fully dense metal parts with complex internal structures that could not be achieved by traditional manufacturing methods. However, this process involves extremely high thermal gradients and heating and cooling rates, resulting in residual stresses and distortion, which may greatly affect the product integrity. The purpose of this thesis is to study the features of thermal stress and deformation involved in the DMD process. Utilizing commercial finite element analysis (FEA) software ABAQUS, a 3-D, sequentially coupled, thermo-mechanical model …

Evaluation Of Ceramic Coaxial Cable Sensors For Long-Term In-Situ Monitoring Of Geologic Co₂ Injection And Storage, Yurong Li

Masters Theses

"Monitoring is an essential component of CO₂ injection and storage projects in order to manage the injection process, identify leakage risks, provide early failure warnings, determine the movement of CO₂ plume and provide input into reservoir models. In-situ monitoring provides critical and direct data points that can be used to fulfill the above objectives. However, downhole sensors that can withstand the harsh conditions and run over decades of the project life cycle remain unavailable. A new idea of ceramic coaxial cable temperature, pressure and strain sensor has recently been put forward and the sensors are under development.

A high pressure …

Women In Science 2014, Clark Science Center's Summer Research Fellows Program

SURF Abstracts (Women in Science)

Women in Science 2014 summarizes research done by Smith College’s Summer Research Fellowship (SURF) Program participants. Ever since its 1967 start, SURF has been a cornerstone of Smith’s science education. In 2014, 150 students participated in SURF (141 hosted on campus and nearby eld sites), supervised by 61 faculty mentor-advisors drawn from the Clark Science Center and connected to its eighteen science, mathematics, and engineering departments and programs and associated centers and units. At summer’s end, SURF participants were asked to summarize their research experiences for this publication.

Development Of Low Cost Piezoresistive Organic Cantilever Resonator, D. Thuau, Cedric Ayela, E. Lemaire, Stephen M. Heinrich, P. Poulin, I. Dufour

Civil and Environmental Engineering Faculty Research and Publications

No abstract provided.

End Mass Effects On The Frequency Response Of Cantilevers: Analytical Results, Stephen M. Heinrich, Isabelle Dufour

Civil and Environmental Engineering Faculty Research and Publications

No abstract provided.

Development Of An Instrument To Assess Attitudes Toward Science, Technology, Engineering, And Mathematics (Stem), Tamara J. Moore, Selcen Guzey, Michael Harwell

School of Engineering Education Faculty Publications

There is a need for more students to be interested in science, technology, engineering, and mathematics (STEM) careers to advance U.S. competitiveness and economic growth. A consensus exits that improving STEM education is necessary for motivating more students to pursue STEM careers. In this study, a survey to measure student (grades 4-6) attitudes toward STEM and STEM careers was developed and administered to 662 students from two STEM-focused and three comprehensive (non-STEM focused) schools. Cronbach’s alphas for the whole survey and subscales indicated a high internal consistency. Statistically significant difference in means between students attending the STEM-focused and comprehensive schools …

The Importance Of Formative Assessment In Science And Engineering Ethics Education: Some Evidence And Practical Advice, Matthew W. Keefer, Sara E. Wilson, Harry Dankowicz, Michael C. Loui

School of Engineering Education Faculty Publications

Recent research in ethics education shows a potentially problematic variation in content, curricular materials, and instruction. While ethics instruction is now widespread, studies have identified significant variation in both the goals and methods of ethics education, leaving researchers to conclude that many approaches may be inappropriately paired with goals that are unachievable. This paper speaks to these concerns by demonstrating the importance of aligning classroom-based assessments to clear ethical learning objectives in order to help students and instructors track their progress toward meeting those objectives. Two studies at two different universities demonstrate the usefulness of classroom-based, formative assessments for improving …

Design And Construction Of A Portable Cattle Loading Ramp, Gino A. Torlai

BioResource and Agricultural Engineering

This project is to design and construct an affordable and effective portable cattle loading trailer. The trailer should save money by not having to buy a commercial brand and also by being able to utilize the piece of equipment at multiple different ranches.