Engineering Commons^™

Green Technologies And Sensor Networks For Bmp Evaluation In Stormwater Retention Ponds And Wetlands., Anthony Crawford

Electronic Theses and Dissertations

The aim of this thesis is to examine and develop new techniques in stormwater Best Management Practices (BMP) for nutrient and erosion reduction and monitoring by incorporation of low impact green technologies and sensor networks. Previous research has found excessive nutrient loading of nitrogen and phosphorus species from urban stormwater runoff can lead to ecological degradation and eutrophication of receiving lakes and rivers (Fareed and Abid, 2005). In response, the Florida Department of Environmental Protection (FDEP) has set forth reduction goals as established in Total Maximum Daily Load (TMDL) reports to reduce nutrient loading and restore, or maintain, Florida water …

Graphene Oxide Reinforcement In Plasma Sprayed Nickel-5%Aluminum Coatings, David Ward

Electronic Theses and Dissertations

Metallic plasma sprayed coatings are widely used in the aerospace industry for repair on worn engine components. However, the inherent defects in these coatings limit the variety of repairs and reduce the service life of the repaired parts. A potential solution to overcome this problem is to mix small amounts of inexpensive graphene oxide in the powder feedstock. The incredible strength to weight ratio of graphene oxide makes it a viable additive to improve mechanical properties of metallic plasma sprayed coatings. The powder system chosen for this research is Nickel-5Aluminum since it is a common coating for such repairs. The …

Instructional Strategies For Scenario-Based Training Of Human Behavior Cue Analysis With Robot-Aided Intelligence, Surveillance, Reconnaissance, Julie Salcedo

Electronic Theses and Dissertations

The U.S. Army desires to improve safety during Intelligence, Surveillance, Reconnaissance (ISR) operations by removing Warfighters from direct line-of-fire by enhancing ISR operational capabilities with unmanned systems, also known as Robot-Aided ISR (RAISR) (DOD, 2013). Additionally, RAISR presents an opportunity to fulfill ISR capability requirements of modern combat environments including: detection of High-Value Individuals (HVI) from safer distances, identification of baseline behavior, and interpretation of adversarial intent (U.S. Army, 2008). Along with the demand and projected acquisition of RAISR technology, there is the added need to design training requirements for system operation and task execution instruction. While documentation identifying specific …

Combustion Instability Mechanism Of A Reacting Jet In Cross Flow At Gas Turbine Operating Conditions, Jared Pent

Electronic Theses and Dissertations

Modern gas turbine designs often include lean premixed combustion for its emissions benefits; however, this type of combustion process is susceptible to self-excited combustion instabilities that can lead to damaging heat loads and system vibrations. This study focuses on identifying a mechanism of combustion instability of a reacting jet in cross flow, a flow feature that is widely used in the design of gas turbine combustion systems. Experimental results from a related study are used to validate and complement three numerical tools that are applied in this study – self-excited Large Eddy Simulations, 3D thermoacoustic modeling, and 1D instability modeling. …

In-Situ Synchrotron Studies Of Turbine Blade Thermal Barrier Coatings Under Extreme Environments, Kevin Knipe

Electronic Theses and Dissertations

Thermal Barrier Coatings have been used for decades to impose a thermal gradient between the hot combustion gases and the underlying superalloy substrate in engine turbine blades. Yttria Stabilized Zirconia (YSZ) is an industry standard high temperature ceramic for turbine applications. The protective coating is adhered to the substrate using a nickel based alloy bond coat. Through exposure to high temperature, a Thermally Grown Oxide (TGO) layer develops at the bond coat-YSZ interface. Large residual stresses develop in these layers due to thermal expansion mismatch that occurs during cool down from high temperature spraying and cyclic operating conditions. Despite their …

Synchrotron X-Ray Diffraction And Piezospectroscopy Used For The Investigation Of Individual Mechanical Effects From Environmental Contaminants And Oxide Layer Undulations In Thermal Barrier Coatings, Sanna Siddiqui

Electronic Theses and Dissertations

The durability of Thermal Barrier Coatings (TBCs) used on the turbine blades of aircraft and power generation engines has been known to be affected by sand particle ingression comprised of Calcium-Magnesium-Alumina-Silicate (CMAS). Previous studies have shown that these effects present themselves through variations in the thermomechanical and thermochemical properties of the coating. This study investigated the impact of CMAS ingression on the Yttria Stabilized Zirconia Topcoat (YSZ) and Thermally Grown Oxide (TGO) strain in sprayed Thermal Barrier Coating (TBC) samples of varying porosity with and without CMAS ingression. In-Situ Synchrotron X-ray Diffraction measurements were taken on the sample under thermal …

Nanocomposite Coating Mechanics Via Piezospectroscopy, Gregory Freihofer

Electronic Theses and Dissertations

Coatings utilizing the piezospectroscopic (PS) effect of alpha alumina could enable on the fly stress sensing for structural health monitoring applications. While the PS effect has been historically utilized in several applications, here by distributing the photo-luminescent material in nanoparticle form within a matrix, a stress sensing coating is created. Parallel to developing PS coatings for stress sensing, the multi-scale mechanics associated with the observed PS response of nanocomposites and their coatings has been applied to give material property measurements, providing an understanding of particle reinforced composite behavior. Understanding the nanoparticle-coating-substrate mechanics is essential to interpreting the spectral shifts for …

Processing And Characterization Of Multifunctional Thermoplastic Nanocomposite Films, Xin Wang

Electronic Theses and Dissertations

Nanoparticles reinforced polymer composite films have been widely studied for their enhanced mechanical, electrical and thermal properties compared with host polymer matrix. However, most research was conducted on incorporation of nanoparticles in polymer films to improve single property and there is a lack of research on the multifunctional polymer nanocomposite films. In this work, a scalable and continuous spray deposition process was developed for the production of nanoparticles reinforced multifunctional thermoplastic nanocomposite films. This process is capable of making a thin sheet of thermoplastic nanocomposites with high nanoparticle loadings. The smallest thickness can be 40um. The objective of this study …

Investigation Of Different Dielectric Materials As Gate Insulator For Mosfets, Ritika Oswal

Electronic Theses and Dissertations

The scaling of semiconductor transistors has led to a decrease in thickness of the silicon dioxide layer used as gate dielectric. The thickness of the silicon dioxide layer is reduced to increase the gate capacitance, thus increasing the drain current. If the thickness of the gate dielectric decreases below 2nm, the leakage current due to the tunneling increases drastically. Hence it is necessary to replace the gate dielectric, silicon dioxide, with a physically thicker oxide layer of high-k materials like Hafnium oxide and Titanium oxide. High-k dielectric materials allow the capacitance to increase without a huge leakage current. Hafnium oxide …

Automatic 3d Human Modeling: An Initial Stage Towards 2-Way Inside Interaction In Mixed Reality, Yiyan Xiong

Electronic Theses and Dissertations

3D human models play an important role in computer graphics applications from a wide range of domains, including education, entertainment, medical care simulation and military training. In many situations, we want the 3D model to have a visual appearance that matches that of a specific living person and to be able to be controlled by that person in a natural manner. Among other uses, this approach supports the notion of human surrogacy, where the virtual counterpart provides a remote presence for the human who controls the virtual character's behavior. In this dissertation, a human modeling pipeline is proposed for the …

An Introductory Study Of The Dynamics Of Autorotation For Wind Energy Harvesting, Bilal Salih

Electronic Theses and Dissertations

Wind turbines have been used for decades to harvest wind energy. They are suitable only to work on close to ground, and have several drawbacks that are related to the availability of the wind and the amount of extracted power compared with the cost of construction. On the other hand, there is an abundant wind power that is available at high altitudes. The wind jet streams at high elevations 8 - 12 kms are pervasive and persistent, and can potentially produce immense wind energy. Even at moderate elevations of 4 - 5 kms, wind power densities are much higher than …

A Continuous Hydrologic Model Structure For Applications At Multiple Time Scales, Jonathan Griffen

Electronic Theses and Dissertations

There are many different controlling factors on the partitioning of rainfall into runoff. However, the influence of each of these controls varies across different temporal scales. Consequently, numerous water balance models have been developed in the literature for application across various time scales. These models are usually developed for a particular time scale so that the controls with the greatest influence on rainfall partitioning are captured. For example, the SCS curve number method was developed to simulate direct runoff at the event scale; the "abcd" model was developed as a monthly water balance model; and the Budyko model was developed …

Evaluating The Effectiveness Of Conversion Of Traditional Five Section Head Signal To Flashing Yellow Arrow (Fya) Signal, Meshal Almoshaogeh

Electronic Theses and Dissertations

In the United States, there are two schemes of operating traffic signal controls for permitted protected left turns (PPLT) namely the traditional five-section head system (known as Dog-House) and the flashing yellow arrow system (FYA). Past studies have agreed that these controls lead to decrease the average delay per left turn vehicle, decrease the protected green time, increase the left turn capacity, and enhance the intersection overall operation. The flashing yellow arrow (FYA) has been approved by the Federal Highway Administration as the national standard for the PPLT operations at signalized intersections. So, the Florida Department of Transportation also approved …

Exploring Sparsity, Self-Similarity, And Low Rank Approximation In Action Recognition, Motion Retrieval, And Action Spotting, Chuan Sun

Electronic Theses and Dissertations

This thesis consists of 4 major parts. In the first part (Chapters 1-2), we introduce the overview, motivation, and contribution of our works, and extensively survey the current literature for 6 related topics. In the second part (Chapters 3-7), we explore the concept of "Self-Similarity" in two challenging scenarios, namely, the Action Recognition and the Motion Retrieval. We build three-dimensional volume representations for both scenarios, and devise effective techniques that can produce compact representations encoding the internal dynamics of data. In the third part (Chapter 8), we explore the challenging action spotting problem, and propose a feature-independent unsupervised framework that …

Utilization Of Simulated Ground Motions For Engineering Performance Assessment Of Tall Buildings, Nenad Bijelic, Ting Lin, Gregory Deierlein

Civil and Environmental Engineering Faculty Research and Publications

No abstract provided.

Decision To Use An Airframe Parachute In A Flight Training Environment, Scott R. Winter, Richard O. Fanjoy, Chien-Tsung Lu, Thomas Q. Carney, James P. Greenan

Publications

The purpose of this study was to complete a qualitative analysis of the decision-making process used by pilots to determine whether or not to deploy an airframe parachute system. A sample of participants from the subject university’s flight training program was selected to complete a scripted simulator flight in instrument flight conditions. During the flight, participants experienced an engine failure while enroute during IFR conditions. The script was examined and validated by an expert panel who determined use of the airframe parachute was the most appropriate outcome for the scenario. Interestingly, only 9 of the 21 participants responded as expected …

Measuring Security: A Challenge For The Generation, Janusz Zalewski, Steven Drager, William Mckeever, Andrew J. Kornecki

Department of Electrical Engineering and Computer Science - Daytona Beach

This paper presents an approach to measuring computer security understood as a system property, in the category of similar properties, such as safety, reliability, dependability, resilience, etc. First, a historical discussion of measurements is presented, beginning with views of Hermann von Helmholtz in his 19th century work “Zählen und Messen”. Then, contemporary approaches related to the principles of measuring software properties are discussed, with emphasis on statistical, physical and software models. A distinction between metrics and measures is made to clarify the concepts. A brief overview of inadequacies of methods and techniques to evaluate computer security is presented, followed by …

Keeping The Skies Safe, Massood Towhidnejad, Andrew J. Kornecki

Department of Electrical Engineering and Computer Science - Daytona Beach

Professors Massood Towhidnejad and Andrew Kornecki shine a light on how their lab is helping government and the aviation industry to enhance the safety and security of software-intensive systems.

Characterization Of The Relationship Between Firms And Universities And Innovation Performance: The Case Of Colombian Firms, Fredy Gomez, Tugrul U. Daim, Jorge Robledo

Engineering and Technology Management Faculty Publications and Presentations

Within the National Innovation System, universities play a key role as the main source of knowledge that supports national productivity and as a system that seeks to improve the competitiveness of firms competitiveness and to find answers concerning market needs in today’s fast-changing and globalized economy. Innovation, as a source of competitiveness, is normally supported by a firm’s technological capabilities: internal R&D, external collaborative agreements, and relationships with universities. This study uses a cluster analysis to identify three clusters that represent respectively those firms that interact closely with universities for technology development (which include R&D projects) and technological learning activities, …

Improving Forecast Accuracy By A Segmented Rate Of Change In Technology Forecasting Using Data Envelopment Analysis (Tfdea), Dong-Joon Lim, Timothy R. Anderson

Engineering and Technology Management Faculty Publications and Presentations

Technology forecasting using data envelopment analysis (TFDEA) captures technological advancement from the evolution of the state-of-the-art (SOA) frontier. Within this process, TFDEA combines rates of changes (RoC) from past technologies that have been superseded by superior technologies. However, it was occasionally observed in previous applications that forecasting based on a single aggregated RoC did not consider the unique growth patterns of each technology segment, which resulted in a conservative or aggressive forecasting. This study proposes a procedure to improve the forecasting accuracy by identifying local rates of change for each frontier segment that may represent different product families. This approach …

Exploring Linkage Of Quality Management To Innovation, Scott A. Leavengood, Timothy R. Anderson, Tugrul Unsal Daim

Engineering and Technology Management Faculty Publications and Presentations

In many business sectors today, focus on quality as a competitive tool is being replaced by a focus on innovation. Research exploring connections between quality management, innovation, and company performance suggests that quality is ‘necessary but insufficient’ in business today. In short, managers need to know how to adapt their quality management practices to achieve innovation performance in addition to quality performance. West coast U.S. forest products manufacturers were surveyed about their quality management practices and performance with respect to both quality and innovation. Results were analyzed to identify two categories of high-performing firms: those achieving primarily quality outcomes and …

The Effect Of Using Different Rock Failure Criteria In Wellbore Stability Analysis, Reza Rahimi

Masters Theses

"Determination of the appropriate drilling fluid density by rock failure analysis is an essential step to control wellbore instability. To determine wellbore failure stresses, the rock strength has to be known, an appropriate constitutive model has to be selected, and finally an accurate rock failure criterion must be chosen. Linear-poro elastic modeling of the mechanical wellbore failure is the most common approach to investigate wellbore instability. Numerous failure criteria have been used for the rock failure analysis but there is not any commonly accepted agreement of which failure criteria to use. Rock failure criteria differ in two main characteristics. First, …

Non-Hydrostatic Models For Wave Propagation, Breaking, And Run-Up, Zhangping Wei

Electronic Theses and Dissertations

This dissertation develops a series of non-hydrostatic pressure wave models based on the finite element free surface flow model, CCHE2D, for simulating propagation, breaking, and run-up of coastal wave processes. The first non-hydrostatic formulation presented in this dissertation directly introduces a non-hydrostatic pressure module into CCHE2D. An edge-based pressure allocation method is implemented, and a depth-integrated vertical momentum equation is introduced. The depth-integrated horizontal momentum equations are solved for a provisional velocity field, and then the non-hydrostatic pressure is obtained by satisfying the divergence-free velocity field condition, subsequently the velocity field is corrected by the non-hydrostatic pressure. Finally the free …

Optimization Of Wind Fence Enclosures For Infrasonic Wind Noise Reduction, Johnpaul Russell Abbott

Electronic Theses and Dissertations

A large porous wind barrier enclosure has been built and tested to optimize wind noise reduction at infrasonic frequencies between 0.01-10 Hz in order to develop a technology that is simple, cost effective, and improves upon the limitations of pipe and porous hose arrays. The effects of varying the fence's porosity, modifying its top condition and bottom gap, doubling the height and diameter, and adding a secondary wind barrier were investigated. A simple mathematical model which estimates the wind noise measured at the center of the enclosure was derived based on the measured turbulence and velocity profiles measure outside the …

Developing Genetic Tools For Geobacillus, Brittany Artale

Honors Theses and Capstones

Bacillus and Geobacillus are the primary bacterium used in biotechnology industries due to their ability to excrete extracellular materials such as proteins, enzymes and other byproducts. Bacillus subtilis, has a well-characterized competence machinery, giving way to characterized genetic tools. However, a significant problem associated with working with Bacillus is the regulation of endospore formation. An alternative to Bacillus is Geobacillus, a thermophilic bacterium. Thermophiles offer significant advantages over other bacteria as host organisms in biofuel, bioremediation, and biocatalyst processes. However, the genetic tools and competency associated with Geobacillus is still unknown. Through, genetic engineering the ability …

The Goddard Project, Cassandra Denunzio, Robert Galli, Cameron Perl, Andrew Felicetti, Samuel Cordeiro, Kevin Tierney

Honors Theses and Capstones

The goal of this project was to design and build a robotic dog modeled after Goddard from the 2001 television series, The Adventures of Jimmy Neutron Boy Genius. Sheet metal was used for the body of the robot in order to keep the frame lightweight. Goddard travels on two wheels powered by electric motors and two caster wheels. The robot utilizes a Raspberry Pi as its master device and an Arduino Uno in order to control the robot. Essentially, Goddard acts and behaves like an ordinary dog from barking, to moving around, to being a great companion and friend. …

Electromagnetic Cell With Three-Dimensional Polarization Dynamic Control, Bo O. Zhu, Weng Cho Chew, Lijun Jiang

Electrical and Computer Engineering Faculty Research & Creative Works

An electromagnetic (EM) cell is demonstrated to create the uniform electric field with 3-D polarization dynamic control for the EM compatibility/ interference (EMC/EMI) testing. We utilize 3-D orthogonal slotline structures to build the walls of the EM cell and produce uniform electric field inside the cell by feeding the slotlines in phase and terminating them with matching loads. The uniform electric field is similar to a standing wave produced by the slotline modes propagating in opposite directions. Microwave switches are integrated into the slotlines so that we can choose the operating slotline dynamically and change its orientation in a 3-D …

Evaluation And Analysis Of Distributed Graph-Parallel Processing Frameworks, Yue Zhao, Kenji Yoshigoe, Mengjun Xie, Suijian Zhou, Remzi Seker, Jiang Bian

Publications

A number of graph-parallel processing frameworks have been proposed to address the needs of processing complex and large-scale graph structured datasets in recent years. Although significant performance improvement made by those frameworks were reported, comparative advantages of each of these frameworks over the others have not been fully studied, which impedes the best utilization of those frameworks for a specific graph computing task and setting. In this work, we conducted a comparison study on parallel processing systems for large-scale graph computations in a systematic manner, aiming to reveal the characteristics of those systems in performing common graph algorithms with real-world …

Space Tourism: Hurdles And Hopes, Robert A. Goehlich

Publications

According to the Space Policy Institute (2002, Bib. section), “Space tourism is the term broadly applied to the concept of paying customers traveling beyond Earth’s atmosphere.” Operating reusable launch vehicles (RLVs) might be a first step toward achieving mass space tourism. Thus, the aim of this article is to investigate the potential hurdles and other aspects of importance that must be overcome in order to use RLVs for space tourism flights. The primary ones are social issues (e.g., “Is space tourism ethically acceptable?”), institutional issues (e.g., “Is environmental pollution caused by space tourism more harmful than other emission sources?”), and …

Aircraft Materials And Analysis, Tariq Siddiqui

Publications

Note: This pdf only includes chapter 1 and 10.

Complete coverage of aircraft design, manufacturing, and maintenance

Aircraft Materials and Analysis addresses aircraft design, mechanical and structural factors in aviation, flight loads, structural integrity, stresses, properties of materials, compression, bending, and aircraft fatigue. Detailed analysis of the failure process is provided.

This authoritative guide examines materials used in aircraft construction such as aluminum, steel, glass, composite, rubber, and carbon fiber. Maintenance procedures for corrosion and aging aircraft are discussed and methods of inspection such as nondestructive testing and nondestructive inspection are described. Accident investigation case studies review aircraft design, material …