Engineering Commons^™

A One-Dimensional Model Of A Closed-Loop Refrigeration Test Block For Centrifugal Compressors, Paul D. Gessler

Master's Theses (2009 -)

The increasingly competitive building equipment and control industry pushes manufacturers to continually improve the performance and efficiency of their products to develop and maintain a competitive edge. Compressor development is an expensive endeavor, but the cost and time required for testing can be minimized by developing a model of the compressor test block to predict its behavior with a given prototype compressor at specified operating conditions. This thesis presents a thermodynamic model of a hot gas bypass test block used to evaluate centrifugal compressor performance at a compressor development facility. The test block uses cooling towers to reject the heat …

Spatial Visualization Ability And Impact Of Drafting Models: A Quasi Experimental Study, Petros J. Katsioloudis, Vukica Jovanovic

STEMPS Faculty Publications

A quasi experimental study was done to determine significant positive effects among three different types of visual models and to identify whether any individual type or combination contributed towards a positive increase of spatial visualization ability for students in engineering technology courses. In particular, the study compared the use of different visual models - a 3D printed solid object, a 3D computer generated drawing and a 2D drawing.

Recruitment Of The Adaptor Protein Grb2 To Egfr Tetramers, Noga Kozer, Dipak Barua, Christine Henderson, Eduoard C. Nice, Antony W. Burgess, William S. Hlavacek, Andrew H. A. Clayton

Chemical and Biochemical Engineering Faculty Research & Creative Works

Adaptor protein Grb2 binds phosphotyrosines in the epidermal growth factor (EGF) receptor (EGFR) and thereby links receptor activation to intracellular signaling cascades. Here, we investigated how recruitment of Grb2 to EGFR is affected by the spatial organization and quaternary state of activated EGFR. We used the techniques of image correlation spectroscopy (ICS) and lifetime-detected Förster resonance energy transfer (also known as FLIM-based FRET or FLIM-FRET) to measure ligand-induced receptor clustering and Grb2 binding to activated EGFR in BaF/3 cells. BaF/3 cells were stably transfected with fluorescently labeled forms of Grb2 (Grb2-mRFP) and EGFR (EGFR-eGFP). Following stimulation of the cells with …

Effectiveness Of Air Sealing Measures And Other Energy Retrofit Measures In Lafayette Energy Improvement Program, Jia Ye

Open Access Theses

From September 2011 to March 2013, the City of Lafayette, IN implemented Lafayette Improvement Program. The goal of this project was to "increase energy efficiency of existing homes through retrofitting, thereby lowering the costs of home ownership within the Vinton and Glen Acres Neighborhood Target Area (The City of Lafayette, 2011)." Energy audit companies carried out before blower door test and after blower door test to identify air tightness of subjects. This paper finds out there was an improvement in air tightness in the population of 85 houses and the degree of improvement was between 16.85% and 17.85%.

Change point …

Material Differences In Equine Cortical And Trabecular Bone, Ryan B. Allen

Master's Theses

A greater understanding of bone materials would be beneficial in creating more accurate computer models and in the making of biomedical products involving bone. This study set out to determine whether cortical and trabecular bone are two separate materials, or whether they are the same material with a variance in porosity. To answer this question, samples were taken from different sections of the equine metacarpus, underwent densitometry analysis and were statistically analyzed. The majority of results suggest that the material is the same between varying densities of bone and thus the same between cortical and trabecular bone. These particular results …

Studies In Software-Defined Radio System Implementation, Harold A. Haldren Iii

Senior Honors Theses

Over the past decade, software-defined radios (SDRs) have an increasingly prevalent aspect of wireless communication systems. Different than traditional hardware radios which implement radio protocols using static electrical circuit, SDRs implement significant aspects of physical radio protocol using software programs running on a host processor. Because they use software to implement most of the radio functionality, SDRs are much more easily modified, edited, and upgraded than their hardware-defined counterparts. Consequently, researchers and developers have been developing previously hardware-defined radio systems within software. Thus, communication standards can be tested under different conditions or swapped out entirely by simply changing some code. …

Biomechanical Applications And Modeling Of Quantum Nano-Composite Strain Gauges, Taylor David Remington

Theses and Dissertations

Biological tissues routinely experience large strains and undergo large deformations during normal physiologic activity. Biological tissue deformation is well beyond the range of standard strain gauges, and hence must often be captured using expensive and non-portable options such as optical marker tracking methods that may rely upon significant post-processing. This study develops portable gauges that operate in real time and are compatible with the large strains seen by biological materials. The new gauges are based on a relatively new technique for quantifying large strain in real-time (up to 40 %) by use of a piezoresistive nano-composite strain gauge. The nano-composite …

Large-Scale Site And Frequency Diversity In Urban Peer-To-Peer Channels For Six Public Safety Frequency Bands, David W. Matolak, Kate A. Remley, Christopher L. Holloway, Qian Zhang, Qiong Wu

Faculty Publications

We report on peer-to-peer large-scale wireless channel characteristics for an urban environment in six public-safety bands, for five simultaneous receiving sites. Results are based upon measurements taken in Denver in July 2009 with stationary receivers and a pedestrian transmitter. The six frequencies at which we measured are (in MHz) 430, 750, 905, 1834, 2400, and 4860. We quantify both site and frequency diversity, and show that 5-site selection yields minimum average gains of 15 dB in mean received power levels; 5-site selection diversity also reduces received power variation by 17-29 dB, depending on frequency. Frequency diversity yields similar gains. By …

Relationship Between Photofixed Condensate, Effluent And Bulk Composition Of Several Common Rtv Materials, Fen Zhou Hanrahan, Natale J. Ianno

Department of Electrical and Computer Engineering: Faculty Publications

Raman spectroscopy and Fourier Transform Infrared (FTIR) spectroscopy are employed to analyze the bulk compositions of five kinds of Room Temperature Vulcanized (RTV) silicones (CV2568, RTV566, DC93-500, SCV2590 and SCV2590-2) that are commonly employed in orbiting spacecraft. It is found that polydimethylsiloxane (PDMS), silicon dioxide, Tetra-n-propylsilicate (NPS), silicic acid, tetraethyl orthosilicate, and trimethylsilanol are contained in all of them. The outgassing products from those silicones are characterized by FTIR. By comparing the position of the peaks, it is found that the outgassing products of each material are PDMS and NPS which are consistent with the compositions of samples determined with …

Biomass Round Bales Infield Aggregation Logistics Scenarios, Cannayen Igathinathane, David Archer, C. Gustafson, Marty Schmer, John Hendrickson, Scott Kronberg, Deepak R. Keshwani, Leslie Backer, Kenneth Hellevang, Timothy Faller

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Biomass bales often need to be aggregated (collected into groups and transported) to a field-edge stack or a temporary storage before utilization. Several logistics scenarios for aggregation involving equipment and aggregation strategies were modeled and evaluated. Cumulative Euclidean distance criteria evaluated the various aggregation scenarios. Application of a single-bale loader that aggregated bales individually was considered as the “control” scenario with which others were compared. A computer simulation program developed determined bale coordinates in ideal and random layouts that evaluated aggregation scenarios. Simulation results exhibited a “diamond pattern” of bales on ideal layout and a “random pattern” emerged when ≥ …

Biofuels From Crop Residue Can Reduce Soil Carbon And Increase Co2 Emissions, Adam J. Liska, Haishun Yang, Maribeth Milner, Steve Goddard, Humberto Blanco-Canqui, Matthew P. Pelton, Xiao X. Fang, Haitao Zhu, Andrew E. Suyker

Adam Liska Papers

Removal of corn residue for biofuels can decrease soil organic carbon(SOC) and increase CO₂ emissions because residue C in biofuels is oxidized to CO₂ at a faster rate than when added to soil. Net CO2 emissions from residue removal are not adequately characterized in biofuel life cycle assessment (LCA). Here we used a model to estimate CO₂ emissions from corn residue removal across the US Corn Belt at 580 million geospatial cells. To test the SOC model, we compared estimated daily CO₂ emissions from corn residue and soil with CO₂ emissions measured using eddy covariance, …

Uncertainties In Life Cycle Greenhouse Gas Emissions From U.S. Beef Cattle, Quentin M. Dudley, Adam Liska, Andrea K. Watson, Galen E. Erickson

Adam Liska Papers

Beef cattle feedlots are estimated to contribute 26% of U.S. agricultural greenhouse gas (GHG) emissions, and future climate change policy could target reducing these emissions. Life cycle assessment (LCA) of GHG emissions from U.S. grain-fed beef cattle was conducted based on industry statistics and previous studies to identify the main sources of uncertainty in these estimations. Uncertainty associated with GHG emissions from indirect land use change, pasture soil emissions (e.g. soil carbon sequestration), enteric fermentation from cattle on pasture, and methane emissions from feedlot manure, respectively, contributed the most variability to life cycle GHG emissions from beef production. Feeding of …

Integrating Mammalian Hazards With Management At U.S. Civil Airports: A Case Study., Kristin M. Biondi, Jerrold L. Belant, James A. Martin, Travis L. Devault, Guiming Wang

United States Department of Agriculture Wildlife Services: Staff Publications

Wildlife incidents with U.S. civil aircraft cost an estimated $1.4 billion from 1990 to 2010, with mammals 5 times more likely to cause damage than other wildlife. We surveyed 2 general aviation (GA) airports and 6 Part-139 certificated (i.e., certified) airports to assess efficacy of management practices for mammalian species hazardous to aircraft. We obtained information on mammalian species present on airport grounds, types and estimated effectiveness of management techniques, and effort spent on wildlife management. We evaluated management techniques relative to aircraft–wildlife collisions (i.e., incident) frequencies taken from Federal Aviation Administration’s (FAA) National Wildlife Strike Database and species hazard …

A Comparative Study Of Gmo Labeling And Liability Systems In The Us, Eu, And South Korea: The Circumstances And A Future Potential For Harmonization, Moonsook Park

Maurer Theses and Dissertations

With the remarkable development of GMOs, GMO trade has also increased. The different attitudes on GMOs among the countries all over the world, specifically the US, EU, and South Korea, have the potential to create international trade conflicts. In order to mediate the conflicts, reasonable labeling and liability systems need to be established to prevent potential GMO risks. The Biosafety Protocol regarding the transboundary movement of GMOs exists to resolve such tensions, but it fails to sufficiently solve the problems and provide clear regulations concerning GMO labeling and liability systems.

A successful GMO labeling and liability system should emphasize the …

An Initial Look At Robotics-Based Initiatives To Engage Girls In Engineering, Jennifer Michaeli, Vukica Jovanovic, Otilia Popescu, Ana Djuric, Ece Yaprak

Engineering Technology Faculty Publications

Over the past 10 years, the use of robotic kits in K-12 Science, Technology, Engineering, and Math (STEM) initiatives as well as undergraduate engineering education has increased significantly. However, a survey of students in grades 9–12 indicated that only 2–3% of women in high school express an intention to study engineering; conversely, 16% of high school men declared that they plan to pursue an engineering degree [1]. In this paper, the authors present an initial review of published literature regarding the use of robotics in schools to identify cases where robotic kits have been used to engage girls in STEM …

A Lightweight And Robust Interference Mitigation Scheme For Wireless Body Sensor Networks In Realistic Environments, S. Liang, Y. Ge, S. Jiang, Hwee-Pink Tan

Research Collection School Of Computing and Information Systems

In dense deployments of Wireless Body Sensor Networks (WBSNs), inter-user interference significantly degrades network performance when multiple WBSN users stay in a small area such as hospitals. Due to the high dynamics of the environments, it is usually hard to schedule the transmissions of multiple WBSNs without a central controller. In this paper, we propose a robust and lightweight interference mitigation scheme for realistic WBSN systems through adaptive channel hopping. A WBSN testbed is set up to investigate the impact of inter-user interference on various performance metrics when different severity levels of interference are present. Based on the measurement results, …

Qos-Aware Data Transmission And Wireless Energy Transfer: Performance Modeling And Optimization, D. Niyato, P. Wang, W. L. Yeow, Hwee-Pink Tan

Research Collection School Of Computing and Information Systems

With wireless energy transfer, a mobile node can operate perpetually without having a wired connection to charge its battery. In this paper, we present a quality of service (QoS) aware data transmission and wireless energy transfer for the mobile node. The node can request for wireless energy transfer or transmit a packet when the node is in a coverage area of an access point. The node supports service differentiation for different type of traffic (i.e., low and high priority data). To meet the QoS requirement of each traffic type, we present the performance modeling and optimization framework. The objective is …

Robust Tracking With Discriminative Ranking Middle-Level Patches, Hong Liu, Zilin Liang, Qianru Sun

Research Collection School Of Computing and Information Systems

The appearance model has been shown to be essential for robust visual tracking since it is the basic criterion to locating targets in video sequences. Though existing tracking-by-detection algorithms have shown to be greatly promising, they still suffer from the drift problem, which is caused by updating appearance models. In this paper, we propose a new appearance model composed of ranking middle-level patches to capture more object distinctiveness than traditional tracking-by-detection models. Targets and backgrounds are represented by both low-level bottom-up features and high-level top-down patches, which can compensate each other. Bottom-up features are defined at the pixel level, and …

A New Clustering Protocol For Hybrid Sensor Vehicular Networks (Hsvns), Saleha Mubarak Mohammed Al Mheiri

Theses

As the UAE is classified among the highest countries in road accidents; it’s an urgent necessity to derive proper and effective solutions. One of the well-known solutions is to move to the Intelligent Transportation Systems (ITS). ITS is achieved by the implementation of advanced technologies to help the roads to be smarter, safer and more coordinated. There are different studies and researches published in this area. This thesis is mainly conducted to achieve the same goal, which is increasing the safety on our roads.

The aim of this research is to build a new clustering protocol in the Hybrid Sensor …

3d Aerodynamic Optimization Of Nrel Vi Wind Turbine Blade For Increased Power Output And Visualization Of Flow Characteristics, Tsewang Rabga Shrestha

Doctoral Dissertations and Master's Theses

The thesis focuses on the aspect of optimization of NREL VI wind turbine blade for increased power output using commercial solver ANSYS 14.5. The power curve obtained from BEMT, Baseline NREL VI CFD Simulations and Optimized Blade Simulations are compared with experimental results. Over prediction is observed in the theoretical result while computational analysis under predicts power produced at post stall region. Parameter correlation and sensitivity analysis study relates the effectiveness of design parameters on the objective outcome. Scatter plots and Determination Matrix indicate the problem setup as non-linear quadratic. Adaptive Single Objective Optimization algorithm is used for the optimization …

Low Noise Nmos Imager Fabrication With A Study On The Effect Of Photodiode Shape On Dark Current, Steven Taylor

Masters Theses

The purpose of this project was to fabricate a low noise N-type Metal-Oxide- Semiconductor (NMOS) imager in the Grand Valley State University (GVSU) Cleanroom with a focus on reducing pixel dark current. Previous research suggests Photodiode (PD) shape affects dark current and charge transfer characteristics of the pixel. Five PD shapes were designed to determine an optimized pixel shape with respect to dark performance. PN junction PDs with the Three Transistor (3T) pixel architecture were found to be the most suitable for imager fabrication in the GVSU cleanroom. The integrated circuit layout of several 8x8 pixel arrays was designed to …

Studies In Error Correction Coding, Hannah Kirse

Senior Honors Theses

For a proper understanding of the implementation of error correction coding schemes, a basic knowledge of communication channels and networks is necessary. Communication channels incur several types of errors, including noise and signal attenuation. Consequently, the benefits of a particular error control scheme are determined by the errors which occur most frequently. First, the types of transmissions across which errors occur will be considered. Subsequently, the types of errors that can appear during these transmissions and a short discussion of the cause of errors are necessary to understand the several types of errors that can occur. Afterward, the implementation of …

Dynamic Characteristic Identification Of Seismic-Excited Multi-Story Buildings Through Response-Only Technique, Agung Budipriyanto, Priyo Suprobo

Makara Journal of Technology

Identifying dynamic characteristics of civil engineering structures is still a challenging task. It intends to assess behavior of the structures under time-dependent loads. This paper discusses a methodology suitable for identifying the characteristics of multi-story buildings using only their measured response under earthquake ground excitations. Appropriateness of technique used for structural identification was corroborated through coherence of the structure’s responses. The methodology was applied for identifying the characteristics of 14-story and 20-story office buildings located in a high seismic region. Responses of these two buildings recorded during three different seismic ground motions were investigated. The buildings’ response spectral densities and …

Synthesis And Characterization Of Soy-Based Polyurethane Foam With Utilization Of Ethylene Glycol In Polyol, Flora Elvistia Firdaus

Makara Journal of Technology

The use of vegetable oils on replacing petroleum has attracted attention of many researchers. The chemical structure of vegetable oils are different from petrochemicals, so the structure of soybean oil has to be chemically modified through its unsaturated fatty acid chain in triglyceride. A two step process was conducted for the preparation of soy-polyol in designated temperatures; 50 °C, 60 °C, and 70 °C. Ethylene glycol (EG) as co-reagent was taking part in soy-polyol synthesis, and the soy-polyol was used as a sole polyol for polyurethane synthesis. Referred to the previous study, the existence of EG in polyurethane synthesis can …

Performances Of Free-Space Optical Communication System Over Strong Turbulence, Ucuk Darusalam, Purnomo Sidi Priambodo, Harry Sudibyo, Eko Tjipto Rahardjo

Makara Journal of Technology

We report an experimental of free-space optical communication (FSOC) system that use tube propagation simulator (TPS) as the turbulence medium. The FSOC system use wavelength of 1550 nm at the rate transmission of 1000 Mbps and amplified with EDFA at the output of +23 dBm. Index structure of 10-15–10-13 as the representation of atmosphere index turbulences are used for simulation of intensity distribution model or scintillation. The simulation use gammagamma and K model as well. The beam wave propagation models used in simulation are plane wave, spherical wave and Gaussian wave. Spherical wave achieves highest performance via gamma-gamma in strong …

Preparations Of Nanostructured Silicide Bundles And Oxide Arrays, Hirokazu Tatsuoka, Wen Li, Erchao Meng, Daisuke Ishikwa, Kaito Nakane, Shingo Oda, Tomoji Matsushita, Natsuki Kurebayashi

Makara Journal of Technology

A variety of nanostructured silicide bundles and oxide nanowire arrays with abundant, non-toxic materials we are prepared. The CrSi2 nanowire and Mg2Si/MgO composite nanowire bundles were synthesized using a Si substrate and a SiOx nanofiber bundle, respectively. The hexagonal MoSi2 nanosheet bundles were also synthesized using a MoS2 layered material as a template. In addition, ZnO, CuO/Cu2O and a-Fe2O3 nanowire arrays were prepared on semiconductor or metallic substrates. The growth phenomena and the structural properties of the nanostructured materials awere investigated. In addition, the preparations of axial and radial nanowire structures weare examined.

Bioethanol Production From Iles-Iles And Sorghum Starch As Raw Materials (Effect Of Cacl 2 Addition And Saccharification Time), Kusmiyati Kusmiyati, Ali Mahmudi

Makara Journal of Technology

Bioethanol produced from agricultural sources is one alternative energy that has been developed to substitute for petroleum. However, the use of food sources such as corn and cassava to produce bioethanol still face obstacles that lead to the scarcity of food and an increase in food prices. The aim of this study was to produce bioethanol from sorghum and iles-iles, which are not used by humans as food, especially in Indonesia. For both materials, the variables studied were saccharification time (4, 8, 24, and 48 h) and concentration of CaCl2 added to the liquefaction slurry (0, 100, 200, 300, and …

The Effect Of Zephyr Layer Orientation On Zephyrboard Made From Oil Palm Petiole, Lusita Wardani, Muhamad Yusram Massijaya, Yusuf Sudo Hadi, I Wayan Darmawan

Makara Journal of Technology

It is very important to utilize oil palm petiole for the production of zephyr boards. This study aimed to analyze the effect of layer orientation on zephyr board quality. Zephyr boards were made with three coating patterns (A = cross perpendicular, B= combine A and C, and C= paralell) and five zephyr layers using urea formaldehyde adhesive. They were pressed for 20 min at a pressure of 25 kgf/cm² and a temperature 120 ºC, to a target density of 0.80 g/cm³ and a size of 300 mm X 300 mm X 12 mm. Our results showed that the physical and …

Performance Evaluation Of An Optimized Floating Breakwater In Oblique Waves With A Higher-Order Boundary Element Method, Faisal Mahmuddin, Masashi Kashiwagi

Makara Journal of Technology

In the previous study, the optimal performance of a two-dimensional (2D) floating breakwater shape was obtained. The performance of this shape was also confirmed with a model experiment in a towing tank. Moreover, the shape’s performance in three dimensions (3D) was investigated in a subsequent study. However, to predict the shape’s performance in a real application more accurately, the shape’s characteristics in oblique waves must also be evaluated. In this study, the performance and characteristics of the model (hydrodynamic forces, body motions, wave elevations, and drift forces) are computed using a higher-order boundary element method (HOBEM). The HOBEM, which is …

Modeling And Experimental Investigation Of Parabolic Trough Solar Collector, Mohanad Abdulazeez Abdulraheem Alfellag

Doctoral Dissertations and Master's Theses

In this thesis, a mathematical model is applied to study the performance of a parabolic trough solar collector (PTSC). The proposed model consists of three parts. The first part is a solar radiation model. In this section, the amount of solar radiation incident upon Earth is estimated using equations and relationships between the sun and the Earth. The second part is the optical model. This part has the ability to determine the optical efficiency of PTSC throughout the daytime. The last part is the thermal model. The aim of this section is to estimate the amount of energy collected by …