Engineering Commons^™

Inviscid Analysis Of Extended Formation Flight, James Kless, Michael Aftosmis, Andrew Ning, Marian Nemec

Faculty Publications

Flying airplanes in extended formations, with separation distances of tens of wingspans, significantly improves safety while maintaining most of the fuel savings achieved in close formations. The present study investigates the impact of roll trim and compressibility at a fixed lift coefficient on the benefits of extended formation flight. An Euler solver with adjoint-based mesh refinement combined with a wake propagation model is used to analyze a two-body echelon formation at a separation distance of 30 spans. Two geometries are examined: a simple wing and a wing-body geometry. Energy savings, quantified by both formation drag fraction and span efficiency factor, …

Why A 15 Minute Biological Detection System?, Doug Lewis

Faculty Publications

The biological defense community needs to take a hard look at the requirements and assumptions we use to develop our biological sensors. Today the point sensors currently deployed or in development can offer at best “near real time” detection. This translates into approximately 10-20 minutes from the time an agent passes over the device until an alarm is issued. Why are we working to develop detection hardware which in reality contributes little to no advantage to an operational environment? Should the DOD resist fielding (in the near term) “near real time” detection systems, and instead field slower (but much more …

Current Barriers To Successful Implementation Of Fist Principles, Brandon Keller, Joseph R. Wirthlin

Faculty Publications

The Fast, Inexpensive, Simple, and Tiny (FIST) framework proposes a broad set of organizational values, but provides limited guidance on practical implementation. Implementing FIST principles requires clarifying the definitions of “fast,” “inexpensive,” and “simple,” recognizing where FIST does and does not apply. Additionally, a subset of the FIST heuristics was expanded upon to increase their usefulness for practitioners. The primary research findings are that FIST principles are less conducive for highly complex or novel systems, immature technologies, future needs, acquisitions in early development phases, or when performance is the foremost value. FIST principles were also found to be constrained by …

Tesla: An Extended Study Of An Energy-Saving Agent That Leverages Schedule Flexibility, Jun Young Kwak, Pradeep Varakantham, Rajiv Maheswaran, Milind Tambe, Burcin Becerik-Gerber

Research Collection School Of Computing and Information Systems

This paper presents transformative energy-saving schedule-leveraging agent (TESLA), an agent for optimizing energy usage in commercial buildings. TESLA’s key insight is that adding flexibility to event/meeting schedules can lead to significant energy savings. This paper provides four key contributions: (i) online scheduling algorithms, which are at the heart of TESLA, to solve a stochastic mixed integer linear program for energy-efficient scheduling of incrementally/dynamically arriving meetings and events; (ii) an algorithm to effectively identify key meetings that lead to significant energy savings by adjusting their flexibility; (iii) an extensive analysis on energy savings achieved by TESLA; and (iv) surveys of real …

Factors Leading To Decentralization Of Ict Companies: The Case Of Multimedia Super Corridor, Malaysia, Muhammad Asim Tufail, Abu Hassan Abu Bakar, Wiwied Virgiyanti, Faisal Manzoor Arain

Business Review

Technological development in the information and communication technologies (ICT) sector is essential to attain sustainability in today’s era. Cities have developed satellite towns at the periphery with hi-fidelity digital and physical infrastructure which converts a single cantered city into a multi cantered one. In case of Kuala Lumpur Metropolitan Area (KLMA) the shift of civic services to Putrajaya and development of Multimedia Super Corridor (MSC) which offers incentives to local and foreign companies to develop a super block of research and development based economic sector. This development spearheaded the Malaysian Vision 2020 of knowledge based economy and society and has …

Cable Median Barrier Failure Analysis And Remediation Phase Ii, Cody S. Stolle, Dean L. Sicking, Ronald K. Faller, John D. Reid

Nebraska Department of Transportation: Research Reports

Cable median barrier crashes from a total of 12 states were analyzed. Crash data included scene diagrams, photographs, and field measurements, crash narratives, although the availability of data in each crash varied.

Major contributors to penetration crash propensity were identified: diving underride, in which the front end of the vehicle dropped below the bottom cable; prying, in which the vehicle profile caused cable separation or lifting; override; bouncing override, in which the vehicle rebounded after contact with the back slope and bounced over the top of the barrier; system failure, in which one component failure or design failure prevented the …

Open Source Kiswahili Spell Checker (Sw-Tz), Hashim Twaakyondo

Tanzania Journal of Engineering and Technology (TJET)

Different English software products are localized into many native languages spoken around the world, the most popular software products localized so far are word processing software and web browsers. The effort has begun to localize these software products in Kiswahili language which is widely spoken in Tanzania, East and Central Africa. Kiswahili is an official language of Tanzania, and is a national language in Uganda and Kenya. To make these software products useful to Kiswahili speaking community particularly in Tanzania a new Kiswahili spell checker has been developed and, it uses most of the Kiswahili words spoken in Tanzania and …

Isolation And Characterisation Of Micro-Organisms With Industrial Importance From Sisal Bole Rots, Consolatha Mhaiki

Tanzania Journal of Engineering and Technology (TJET)

Investigation of microorganisms naturally acclimatized to Agave hybrid H 11648 (sisal bole rot) was conducted, with the aim of isolating and characterizing Aspergillus niger strains for industrial use. Microorganism were identified morphologically and then confirmation made by polymerase chain reaction (PCR). Results showed the existence of four major groups, listed in order of abundances as follows; Aspergilli (36.0±0.8) %, Penicillin (28.0±0.1) %, Yeast (15.0±1.6) %and Fusarium (10.0±0.12) %. The main groups of Aspergilli strains were A. nidulans, A. tamari and A. niger in ratios (3:2:2), respectively. Several endo-spore forming non-enteric gram (-) rods and coccid bacteria identified by API 20 …

2d Autocad Geometric Data Extraction And Post Processing For Numerical Control, Tito Mwinuka

Tanzania Journal of Engineering and Technology (TJET)

In this paper, a method of extracting 2D geometric data from AutoCAD drawing and post processing for Numerical Control (NC) is presented. Geometric data already available in the Drawing Interchange Files (DXF) can be utilized to accurately and economically prepare part programs for controlling NC/CNC machine tools. AutoCAD, being general purpose software, stores its geometric data in a form that cannot be directly applied for automatic generation of Numerical Control (NC) codes. The way around the discrepancy between the structure of a drawing database (DXF files) and the information requirement for part programming is addressed in this work. NC programming …

Improvement Of Hydraulic Press For Vegetable Oil Expression In Rural Areas, I. P. Bateebe

Tanzania Journal of Engineering and Technology (TJET)

Cultivation of oil producing crops especially Jatropha and croton as source of vegetable oil for biodiesel production is being encouraged in rural areas. To recover oil from seed, manual press is the feasible method in rural areas where there is no electricity. Research was conducted to improve hydraulic oil press machine for rural application. Factors affecting oil recovery were found to be: moisture content of seeds, operating pressure, seed oil content, and the amount of seeds pressed per batch. Percentage oil recovery was improved by reducing diameter of press cylinder, hence increasing expression pressure, and either reducing amount of seed …

Problems And Prospects Of Hydraulic Modelling For Environmental Flows Assessment Studies In East Africa, Preksedis Ndomba

Tanzania Journal of Engineering and Technology (TJET)

The objective of this paper is to document the problems and prospects of hydraulic modelling for Environmental Flows Assessment (EFA) studies based on selected case studies. Most of studies in East Africa use Holistic methodologies. An ideal data set for defining river hydraulics for most of these methods would be six data points of stage measurements over a good distribution of discharges, the stage of zero discharge and some flood-related data. Besides, in East African region EFA studies suffer from data scarcity (i.e., poorly gauged sites) and limited expertise and funding. The hydraulics studies conducted by the authors entailed desktop …

Gas Leakage Detection System (Glds), Daudi Simbeye

Tanzania Journal of Engineering and Technology (TJET)

This paper mainly focuses on the detection of gas leakage and providing security when the user is around or away from home. The system is Short Message Service (SMS) based and uses wireless technology for providing security against gas leakage to users hence cost effective and more adaptable. The system comprises of sensors for detecting gas leak interfaced to microcontroller that will give an alert to user whenever there is a gas leakage, display warning information by using Liquid Crystal Display (LCD), sending SMS to the user for notification wherever he/she might be and turning off electric power with the …

Investigation Of Thermal Properties And Latent Heat Reduction Mechanisms In Nanofluid Phase Change Materials, Aitor Zabalegui

Mechanical Engineering Master's Theses

The thermal properties of paraffin-based nanofluids have been examined to investigate the use of enhanced phase change materials (PCMs) for thermal energy storage (TES). PCMs are promising for TES applications, but low thermal conductivity limits their rate of heat exchange with a working fluid. The nanofluid approach has been established as a method of thermal conductivity enhancement, but effects of particle addition on other thermal properties affecting TES are relatively ignored. Significant reduction in latent heat of fusion below traditional effective medium theory has been observed in nanofluids. An experimental study of paraffin nanofluids, containing various diameter multi-walled carbon nanotubes, …

Effect Of Ethyl Propionate On Low-Temperature Performance Of Lifepo4-Based Li-Ion Battery, Xiao-Ping Li, Lian-Sheng Hao, Wei-Shan Li, Meng-Qing Xu, Li-Dan Xing

Journal of Electrochemistry

A linear carboxylic, ester ethyl propionate (EP), was used as the co-solvent of carbonates, ethylene carbonate (EC), ethyl-methyl carbonate (EMC) and dimethyl carbonate (DMC), and its effect on low-temperature performance of LiFePO₄-based Li-ion battery was studied by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic charge-discharge test. The application of EP enhances the ionic conductivity of the electrolyte, improves the compatibility of the electrolyte with both LiFePO₄ and graphite materials, and thus improves the low-temperature performance of LiFePO₄-based Li-ion battery. The Li-ion battery using the optimized electrolyte of 1 mol·L^-1 LiPF₆/EC:EMC:DMC:EP …

Multifunctional Corrosion Inhibition Behavior Of Zn-Al Calcined Layered Double Hydroxides For Steel Rebar In Nacl Solution, Xiao-Juan Zhang, Jing-Jing Wang, Shi-Gang Dong, Chang-Jian Lin

Journal of Electrochemistry

The Zn-Al layered double hydroxides (Zn-Al LDHs) and calcined products (Zn-Al CLDHs) were synthesized successfully under a routine air atmosphere. The results showed that both Zn-Al LDHs and Zn-Al CLDHs had obvious flake structures. The corrosion inhibition of Zn-Al CLDHs for steel rebar in NaCl solution was studied by electrochemical techniques. It was found that the corrosion rate of steel rebar decreased significantly after the steel rebar was treated by Zn-Al CLDHs in NaCl solution for 3 h. It was indicated that Zn-Al CLDHs could absorb Cl^- and release OH^- during their reconstruction process, which provided dual protection …

Influences Of The Cinnamic Acid On Zinc Electrodeposition At Glassy-Carbon Electrode, Kai Li, Shen Chen, Shen-Na Liu, Bi-Sang Chen, Heng Lin, Guo-Liang Chen, Qing-Xiang Wang

Journal of Electrochemistry

The influences of cinnamic acid (CIN) on the mechanism of Zn deposition and nucleation kinetics onto glassy-carbon electrode were studied by cyclic voltammetry (CV) and chronoamperometry (CA). The results revealed that the zinc reduction took place via Zn²⁺ + 2e → Zn in the presence of CIN, but the kinetics of zinc deposition was changed and the formation rate of zinc nuclei was accelerated. In the absence of CIN, the mechanism of zinc nucleation followed the 3D-instantaneous diffusion-controlled nucleation, while the 3D-progressive diffusion-controlled nucleation in the presence of CIN. The addition of CIN reduced the nucleation rate, but increased …

Preparation And Characterization Of A Novel Composite Electrolyte Ceria-Sulfate For Intermediate Temperature Solid Oxide Fuel Cells, Ze Tong, Yi-Mei Yin, Jie-Wei Yin, Zi-Feng Ma

Journal of Electrochemistry

A novel composite electrolyte SDC-(Li/Na)₂SO₄ was prepared for intermediate temperature solid oxide fuel cells (ITSOFC). The phase structure and cross-sectional morphology were examined by XRD and SEM, respectively, and the ionic conductivity was investigated by AC impedance in a temperature range of 400 ^oC ~ 700 ^oC in air. It was found that the composite electrolyte was composed of two phases: crystal SDC and amorphous (Li/Na)₂SO₄. The conductivity of the composite electrolyte was significantly larger than that of SDC at intermediate temperatures (550 ^oC ~ 700 ^oC) and increased …

The Effect Of Precursors On Performance Of Lini0.5Co0.2Mn0.3O2 Cathode Material, Dong-Ge Hu, Zhang-Zhi Wang, Jia-Li Liu, Tao Huang, Ai-Shui Yu

Journal of Electrochemistry

Commercial LiNi_0.5Co_0.2Mn_0.3O₂ material is generally prepared by a combination of co-precipitation and solid state reaction method. The particle size distribution and morphology of Ni_0.5Co_0.2Mn_0.3(OH)₂ precursor have a great impact on the electrochemical performance of LiNi_0.5Co_0.2Mn_0.3O₂. In this work, the crystal structure and surface morphology of LiNi_0.5Co_0.2Mn_0.3O₂ prepared by three different precursors were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Particle size distribution, tap density and electrochemical performance were …

Influence Of Electrode Hydrophobicity On Performance Of Alkaline Polymer Electrolyte Fuel Cells, Li-Sheng Tan, Jing Pan, Yao Li, Lin Zhuang, Jun-Tao Lu

Journal of Electrochemistry

In the present work, we study the influence of the electrode hydrophobicity on the performance of alkaline polymer electrolyte fuel cells (APEFCs). QAPS or xQAPS is employed as the membrane and the ionomer, while PTFE is used as a hydrophobic additive in order to adjust the electrode hydrophobicity. We find that enhancing the hydrophobicity of anode can promote the performance of APEFCs, while a moderate hydrophobicity of cathode is required to achieve optimal performance. By using xQAPS as the electrolyte and adding some PTFE in the anode, a peak power density of 132 mW·cm^-2 can be obtained at a …

Electrocatalytic Mechanism And Porous Electrode Mass Transfer Process In Membrane Electrode Assembly For Direct Methanol Fuel Cells, Xin-Dong Wang, Yi-Tuo Wang, Gui-Cheng Liu, Meng Wang, Zhe Tian

Journal of Electrochemistry

Direct methanol fuel cell (DMFC) is considered to be a promising commercial energy conversion device for portable electronics due to its many advantages. In order to improve the performance of DMFC, many companies and research institutes have been launching the deep research and obtaining a lot of conspicuous achievements. In this paper, the electrocatalytic mechanism and porous electrode mass transfer process in membrane electrode assembly (MEA) are analyzed. In addition, combined with the preparation process of MEA, multilayer ordered structures and internal transfer process of the cell, recent progresses of MEA in DMFC are discussed.

Electrochemical Nanofabrication Using Polyacrylamide Hydrogel As Soft Stamps, Wen Sun, Hai-Tao Fan, Da-Xiao Zhang, Dong-Jie Hu, Yong-Liang Zhou

Journal of Electrochemistry

The fabrication resolution of electrochemical wet stamping (E-WETS) was enhanced to several hundred nanometers from several ten micrometers by using polycarylamide gel (PAG) as soft stamps and through optimized processes. The PAG stamp was cured on a nanopatterned soft mold and soaked with 0.2 mol·L^-1 KCl solution, then contacted with a silicon wafer with gold film and applied with electric field. And the gold nanopatterns were achieved by the selective anodic dissolving, the diameter of fabricated gold spot was around 200 nm. The parameters which affected the fabrication processes have been discussed in detail.

Fabrication And Performance Of Lani0.6Fe0.4O3-δCathode Modified By Coating With Gd0.2Ce0.8O2 For Intermediate Temperature Solid Oxide Fuel Cell, Rui-Xuan Ren, Bo Huang, Xin-Jian Zhu, Yi-Xing Hu, Xiao-Yi Ding, Zong-Yao Liu, Ye-Bin Liu

Journal of Electrochemistry

The symmetric cell of LaNi_0.6Fe_0.4O_3-δ/Sc_0.1Zr_0.9O_1.95/LaNi_0.6Fe_0.4O _3-δ was fabricated with screen printing method. A LaNi_0.6Fe_0.4O_3-δ (LNF) cathode was modified by coating with nano-sized gadolinium-doped ceria (GDC, Gd_0.2Ce_0.8O₂) prepared using a simple combustion process within the pores of the cathode. According to the electrochemical impedance spectra (EIS), the polarization resistance of the pure LNF was 0.70 W·cm² at 750 ºC, while 0.13 W·cm² for the 21.3% GDC (by mass)-coated LNF cathode at the …

Optimization Of Electroless Silver Plating Process On Fabric Surface Without Activation And Sensitization, Bo Lian Wang, Ya Ping Zhao, Zai Sheng Cai

Journal of Electrochemistry

Silver was deposited homogeneously on the surface of polyamide fabric by electroless plating without activation and sensitization. The electroless silver plating process was optimized with the orthogonal array testing strategy. It is found that the optimum conditions are the electroless plating time of 50 min with the concentrations of silver nitrate, sodium hydroxide and ammonium hydroxide being 14 g·L^-1, 6 g·L-1 and 130 mL·L^-1, respectively. The surface morphologies, compositions, and phases of fabric samples were characterized by scanning electron microscopy and energy-dispersive X-ray spectrometry (SEM-EDS), X-ray diffraction (XRD). The wear-resisting property was tested by friction fastness …

Preparation And Electrochemical Performance Of Hollow Carbon Spheres/Sulfur Composite, Jun Zang, Hang Qian, Er-Man Zeng, Juan-Ni Fu, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

Hollow carbon spheres were prepared by the PMMA template. Hollow carbon spheres/sulfur composite was made from sulfur and hollow carbon spheres as a conducting framework. The results of SEM and TEM showed that sulfur was uniformly filled in both of the shell and hollow core of hollow carbon spheres. The electrochemical performance of hollow carbon spheres/sulfur composite was characterized by the charge/discharge method. The results showed the excellent rate and cycle performance of hollow carbon spheres/sulfur composite. The reversible capacities of hollow carbon spheres/sulfur composite are 1145 mAh·g^-1, 824 mAh·g^-1, 702 mAh·g^-1, 586 mAh·g …

Development Of Mobile Ad-Hoc Network For Collaborative Unmanned Aerial Vehicles, Siva Teja Patibandla

Theses and Dissertations

The purpose of this research was to develop a mobile ad-hoc network for collaborative Unmanned Aerial Vehicles (UAVs) based on a mesh networking standard called IEEE 802.11s. A low-cost, small form-factor, IEEE 802.11a based wireless modem was selected and integrated with the existing flight control system developed at Virginia Commonwealth University (VCU) UAV Laboratory. A self-configurable user-space application on the wireless modem was developed to provide functionality to collaborative algorithms, and to monitor the performance of the wireless network. The RAMS simulator, developed at VCU, was upgraded to support the simulation of advanced networking capabilities by integrating with a simulator …

Polypyrrole-Transition Metal-Oxygen Coordination Complexes As High Performance Lithium Storage Material, Ya Mao, Qingyu Kong, Bingkun Guo, Zhaoxiang Wang, Liquan Chen

Journal of Electrochemistry

No abstract provided.

Progress Of Lithium Rich Cathode Materials For Li-Ion Batteries, Jie Zhang, Jiu-Lin Wang, Jun Yang

Journal of Electrochemistry

Lithium rich materials xLi₂MnO₃·(1-x)LiMO₂ (0-1 and low cost. However, the large irreversible capacity during the first cycle, low rate capability and structure collapse during cycling remain impediments in developing these cathodes for applications. The structure analyses and charge/discharge mechanisms for lithium rich materials are currently main research contents. Although whether the lithium rich materials are solid solutions or composite is still controversial, oxygen release mechanism on the first charge 4.5 V plateau of lithium rich materials has come to consistency. Several modifications, such as bulk doping, surface coating and microstructure control, demonstrate promising strategies to …

Electrochemical Performance Of Al-Doped Spinel Limn2O4 Cathode Material For Li-Ion Batteries, Yong-Long Wang, Wen-Ge Wang, Qian Zhang, Xin Wang, Jian-Sheng Cao, Shi-Hai Ye

Journal of Electrochemistry

Spinel LiMn₂O₄, a cathode material for Li-ion batteries, is featured as good high-rate performance, low cost and environmental friendly. The pristine and Al-doped LiMn₂O₄ samples were prepared by sol-gel method. The structure and micromorphology of the as-prepared samples were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results demonstrated that the as-prepared LiMn₂O₄ samples had a typical cubic spinel structure and were composed of sphere-like particles with a diameter range of 300 ~ 500 nm. Galvanostatic charge-discharge tests showed that the LiMn₂O₄ samples doped …

Engineering Performance Of A New Siloxane-Based Corrosion Inhibitor, Niall Holmes, R. O'Brien, P. A. M. Basheer

Articles

This paper presents an evaluation of a new non-toxic corrosion inhibitor on selected engineering properties of concrete mixes with different cementitious materials following a corrosion and durability study on concrete samples. Corrosion inhibitors consist of powders or solutions which are added to concrete when mixed to prevent or delay corrosion of steel by their reaction with ferrous ions to form a stable and passive ferric oxide film on the steel surface. The new inhibitor functions slightly differently and its corrosion inhibition effect is due to the formation of a siloxane coating on the steel surface. Therefore, the performance of the …

Comparison Of Non-Coherent Linear Detection Algorithms Applied To A 2-D Numerical Breast Model, Giuseppe Ruvio, Raffaele Solimene, Antonio Cuccaro, Max Ammann

Articles

A comparative analysis of an imaging method based on a multifrequency Multiple Signal Classification (MUSIC) approach against two common linear detection algorithms based on noncoherent migration is made. The different techniques are tested using synthetic data generated through CST Microwave Studio and a phantom developed from MRI scans of a mostly fat breast. The multifrequency MUSIC approach shows an overall superior performance compared to the noncoherent techniques. This letter reports that this highly performing algorithm does not require any antenna calibration or phase response estimation and allows the use of efficient and complex antenna geometries without difficult algorithm redefinitions.