Engineering Commons^™

Numerical Investigation Of Three-Dimensional Effects Within A Charring Ablator, Alexandre Martin, Ovais U. Khan, Huai-Bao Zhang

Ablation Workshop

Re-entry of a spacecraft occurs at hypersonic regime where flow field is extremely complex. High temperature gradients occurring in the shock-layer region ionizes and dissociates the air. Even if a large portion of heat generated during this process is convected away in the surrounding air, a fraction of it is still transferred to the vehicle. Therefore, it is important to protect the vehicle with a suitable kind of shielding. Of many techniques available today, the use of ablator material is increasing in popularity. The basic idea behind an ablating heat shield is that the energy incident on the spacecraft is …

Experimental Investigation Of Blowing Effects On Turbulent Flow Over A Rough Surface, Mark A. Miller, Sean C. C. Bailey, Alexandre Martin

Ablation Workshop

Entry of spacecraft into an atmosphere occurs at hypersonic speeds, extremely complex flow fields, with aerothermodynamic effects which can cause the surface to be subjected to extreme heating. It is therefore important to protect the vehicle and its payload using a thermal protection system (TPS). Heat shields, which are an important part of a TPS, can be of either ablative or non-ablative types. For an ablative TPS, the energy is dissipated through surface material charring and ablation, as well as releasing gasses which serve to carry energy away from the TPS and thus reduce the total heat flux into the …

Development And Validation Of Sacram: A Swiss Approach To The Computational Response Of An Ablative Material, Ojas Joshi, Georges Duffa, Pénélope Leyland

Ablation Workshop

Future space exploration missions foresee high-speed entries into planetary atmospheres. These latter imply extreme thermal conditions to which the space vehicle is exposed to, and require an appropriate thermal protection system (TPS). The interest of the scientific community in modelling and testing of materials that compose the TPS has hence greatly increased over the past few years. Since a complete set of material properties is not available in open literature, it is difficult to numerically rebuild experiments. The inter-code comparison exercise proposed by the AF/SNL/NASA Ablation Workshop aims to give a baseline platform for ablation code calibration, with a complete …

Advanced Thermal Protection Systems (Tps) And Transition Analysis: Unique Experimental Capabilities And Current Research Efforts At The University Of Texas At Arlington, Matthew Crisanti, Cody Ground, Stefano Gulli, Jared Poempipatana, Luca Maddalena

Ablation Workshop

A unique experimental capability in the academic panorama is the 1.6 MW-classic arc-jet facility located at the Aerodynamics Research Center of the University of Texas at Arlington. The arc-heated wind tunnel has recently been refurbished and repurposed (extended testing time of the order of minutes and testing gas-composition control) for the study and characterization of the aerothermal response of TPS candidate materials for sustained hypersonic flight.

Computational Chemistry Modelling Of The Oxidation Of Highly Oriented Pyrolitic Graphite (Hopg), Savio Poovathingal, Thomas E. Schwartzentruber

Ablation Workshop

Under high heat flux, carbon based Thermal Protection Systems (TPS) are observed to rapidly ablate and an accurate characterization is essential to their design. Dissociated oxygen atoms (from the gas phase) striking the surface of TPS could lead to several possibilites. The O atom could adsorb on the surface, recombine with another O atom to form O2 and oxidize the surface to produce CO or CO2 resulting in recession of the surface (ablation). The goal is to predict finite rate models for these reactions which could be incorporated into CFD and DSMC solvers. Our efforts are to predict the rates …

Preparing Nasa For The 21st Century: Oct Perspective On Edl, Harry Partridge

Ablation Workshop

NASA’s Chief Technologist, within the Office of the Chief Technologist (OCT), is the principal advisor to the NASA Administrator in matters related to Agency-wide technology policy and programs and is responsible for the planning, advocacy and coordination of technology development activities within NASA to meet future mission needs. OCT works with the Mission Directorates and mission planners to infuse new technologies into future missions and with other Governmental Agencies to coordinate technology development efforts of mutual interest. In addition, OCT manages NASA’s Space Technology Program (STP), which also includes the SBIR and STTR programs. In this presentation OCT’s role within …

Introduction: The 5th Ablation Workshop And Beyond, Ioana Cozmuta, Alexandre Martin

Ablation Workshop

No abstract provided.

Matter Under Unusual Conditions, Bernard Zygelman

NSTec UNLV Symposium

What is curiosity – driven research and why do we support it?

Vannevar Bush Science The Endless Frontier (1945)

“Science is the pacemaker of technological progress … New productsand new processes do not appear full-grown. They are founded on newprinciples and new conceptions, which in turn are painstakingly developedby research in the purest realms of science“

•Magnetic Resonance Imaging
•Positron Emission Tomography
•Laser applications
•GPS
•Nano Technology

Establishing A Center Of Excellence For Security Science And Engineering, Ke-Xun Sun

NSTec UNLV Symposium

Outline

• Introduction
• Progress report
• NNSA proposal to establishCenter of Excellence for Security Science and Engineering
• Perspective on UNLV-NSTec collaboration

Unlv Em-Dot Research, Highlights Of Improvised Electric Detonator (Wire Melt) Research, And Comments On Basic Research With Unlv Non-Equilibrium Plasma Pinch, Robert A. Schill Jr.

NSTec UNLV Symposium

UNLV EM DOT

•Patented
–Patent Number: 7,482,814 [1/27/2009]
•Novel Differential Dot
–Wide bandwidth & Matched
–Symmetric, shielded sensor
–Measures the E and B fields at a single point in space simultaneously
•Transient Calibration Technique Developed –Excellent Agreement
–Low inductance test stand –relatively uniform B-field
–Low capacitance test stand –relatively uniform E-field
–Test stand is the limiting factor at this time

Development Of Smart Pv Inverters For The Smart Grid, Yahia Baghzouz

NSTec UNLV Symposium

The Electric Grid has become more complex with recent technological developments. There are more alternative power sources and sensors added into the mix at every part of the grid. The Energy Meter has changed over the past several years as well. The older meters were checked only once a month with a meter reader, but the new "Smart" Meters are capable of reporting energy usage at fifteen minute intervals.

The Water Footprint Of Humanity, Arjen Y. Hoekstra, Mesfin Mekonnen

Daugherty Water for Food Global Institute: Faculty Publications

This study quantifies and maps the water footprint (WF) of humanity at a high spatial resolution. It reports on consumptive use of rainwater (green WF) and ground and surface water (blue WF) and volumes of water polluted (gray WF). Water footprints are estimated per nation from both a production and consumption perspective. International virtual water flows are estimated based on trade in agricultural and industrial commodities. The global annual average WF in the period 1996–2005 was 9,087 Gm3 ∕y (74% green, 11% blue, 15% gray). Agricultural production contributes 92%. About one-fifth of the global WF relates to production for export. …

Achieving Very High Efficiency And Net Zero Energy In An Existing Home In A Hot-Humid Climate: Long-Term Utility And Monitoring Data, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

This study summarizes the first six months of detailed data collected about a single-family home that experienced a series of retrofits targeting reductions in energy use. The project was designed to develop data about how envelope modifications in heating, ventilation, and air conditioning and domestic hot water and renewable measures can result in considerable energy reductions and potentially net zero energy for an existing home. Using utility billing records and recent detailed monitoring data, this study was also able to chronicle the progress of energy reduction over a 22-year period.

The Morphology Evolution And Voiding Of Solder Joints On Qfn Central Pads With A Ni/Au Finish, Julie Silk, Jianbiao Pan, Mike Powers

Industrial and Manufacturing Engineering

In this paper, we report on a comprehensive study regarding the morphology evolution and voiding of SnAgCu solder joints on the central pad of two different packages – QFN and an Agilent package called TOPS – on PCBs with a Ni/Au surface finish. Samples were isothermally aged at the equivalent of 0, 2, 7 and 14 years service life. Representative solder joints were cross-sectioned and analyzed using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) in order to investigate the evolution of the solder joint morphology as a function of Au content and isothermal aging. IMC thickness was …

Electrocatalytic Study Of Pseudomonas Aeruginosa Bte-1 Strain, Ping Zhou, En-Ren Zhang, Li Zhou, Guo-Wang Diao, Jun-Le Niu

Journal of Electrochemistry

The aim of the present study is to investigate the electrocatalytic activity of electricity-producing Pseudomonas aeruginosa BTE-1 strain under anaerobic conditions. Pseudomonas aeruginosa BTE-1 was inoculated into anaerobic three-electrode electrochemical cells, and the electrocatalytic activity was measured at poised potentials. HPLC and cyclic voltammetry were used to detect potential electron mediators in solutions. Experimental results showed that no detectable pyocyanine was excreted by P. aeruginosa BTE-1 strain in the anaerobic electrochemcial cells, and P. aeruginosa BTE-1 exhibited direct electrocatalytic activity through the formation of biofilm on the electrode surface which was induced by the electron transfer from the cells of …

Preparation And Electrochemical Performance Of Lifepo4/C By Spray Drying Method Assisted With Organic Template, Quan-Bing Liu, Yang-Mei Jiang, Hui-Yu Song, Shi-Jun Liao

Journal of Electrochemistry

In this work, the LiFePO₄/C composites were prepared by the spray drying and carbothermal method, and were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and galvanostatic charge-discharge measurements. The effects of the organic assisted templates on the morphologies and electrochemical properties of the LiFePO₄/C composites were investigated. The results showed that the morphology and microstructure of the composites could be tuned by incorporating with the different templates. The morphology of the composite appeared to be solid microspheres if no organic template was added, while porous microspheres, nest-like …

Synthesis And Electrochemical Performance Of Xlifepo4·Yli3V2(Po4)3 Composites, Ping-Ping Ma, Zhi-Jian Liu, Jian-Hua Xia, Yu Chen, Pu Hu, Zhi-Chao Lu, Ding-Guo Xia

Journal of Electrochemistry

A series of xLiFePO₄·yLi₃V₂(PO₄)₃ composites were systematically synthesized through solid state reactions by variations in the proportions of LiFePO₄ and Li₃V₂(PO₄)₃. The properties of the prepared compounds were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical measurements. The capacity of 162.7 mAh/g at 0.2 C rate was obtained with the relatively good cycle stability and good conductivity for 0.95LiFePO₄·0.05Li₃V₂(PO₄)₃ due to more uniformed distributed and smaller particle sizes.

Preparation And Characterization Of Mno/Tin Anode For Lithium Ion Batteries, Gao-Jie Xu, Hai-Yan Yang, Peng-Xian Han, Li-Xue Zhang, Ke-Jun Zhang, Chuan-Jian Zhang, Yu-Hua Fan, Cai-Feng Bi, Guang-Lei Cui

Journal of Electrochemistry

Manganese titanate (MnTiO₃) powder was prepared via a sol-gel method using manganese acetate and tetrabutyl titanate as raw materials, and citric acid as a chelating agent. Through high temperature nitridation of MnTiO₃ powder in ammonia, the MnO/TiN composite was obtained. The phase structure, composition and morphology of the composites were characterized by XRD, SEM and EDS. The electrochemical properties of the composite electrodes were studied by performing cyclic voltammetry, galvanostatic charge and discharge, and electrochemical impedance spectroscopy tests. The MnO/TiN electrode delivered specific capacities of 394 mAh·g^-1 and 146 mAh·g^-1 at the current density of …

Preparation And Hydrogen Evolution Properties Of Ni/Ag2O/Ruo2-Pt Cathodes, Shu Huang, Xue-Ming Li, Wu-Lin Li, Wen Wang

Journal of Electrochemistry

The Ni/Ag₂O/RuO₂-Pt composite cathode was prepared by sol-gel method using RuCl₃ and H₂PtCl₆ as raw materials. The effects of heat treatment conditions and AgNO₃ concentrations on hydrogen evolution properties were investigated. The morphology and composition of Ni/Ag₂O/RuO₂-Pt composite cathode have been characterized by XRD, XPS and SEM-EDS. It is demonstrated that the surface structure of Ni/Ag₂O/RuO₂-Pt composite cathode is more compact, with fewer cracks and larger surface roughness than pure nickel. At the conditions of 0.3 A·cm^-2, 90 ^oC, and …

Integration Of Massive Multiplayer Online Role-Playing Games Client-Server Architectures With Collaborative Multi-User Engineering Cax Tools, Joshua D. Winn

Theses and Dissertations

This research presents a new method for integrating client server architectures that are used for the development of Massive Online Role Playing Games (MMORPG) into multi-user engineering software tools. The new method creates a new architecture named CAx Connect by changing the client-pull-server communication pipeline to a server-push-client communication pipeline, effectively reducing the amount of bandwidth consumed and allowing these tools to utilize multiple server processors for complex calculations. This method was used on the new NX Connect multi-user CAx prototype developed at BYU. The new method provides a road map to further implement this architecture and its services into …

Progress And Perspective Of Fuel Cell Technology, Ming Hou, Bao-Lian Yi

Journal of Electrochemistry

Fuel cell, a clean and high-efficiency electrochemical power source, has being paid much attention worldwide recent years. In this paper, the progress and perspective of fuel cell technology are elucidated in detail. Fuel cells have been applied in some special fields such as spacecraft, shuttle and submarines. However, in the areas of transportation, stationary station and portable power source, fuel cells are still under demonstration due to the durability and cost problems. The reliability and surrounding survivability of fuel cells should be enhanced in the special application. Meanwhile, the durability and cost of fuel cells are the main issues to …

The Electrocatalytic Study Of Licoo2 In Air Electrode For Lithium-Air, Jun Gao, Wei Wu, Yan-Yan Tian, Yong Yang

Journal of Electrochemistry

The LiCoO₂ has been investigated as a new electrocatalyst for air electrodes using homemade lithium-air battery. The electrochemical performance and structural changes of the LiCoO₂ based composite air electrodes have been studied. The results of CV, XRD and charge-discharge tests show that the composite air electrodes composed of LiCoO₂ can greatly improve the discharge performance of lithium-air batteries. In particular when the composite air electrodes are charged to 4.1 V before further discharging, the obvious catalytic effects of LiCoO₂ are attributed to higher valence state of the Co element in LiCoO₂, esp. at charged …

Dissolved Oxygen Seawater Battery With Electrochemical Capacitance, Hai-Bo Xu, Yong-Hong Lu, Wei Zhang, Yan-Ting Yu, Chuan-Wei Yan, Ya-Ping Sun, Lian Zhong, Jian-Guo Liu, Yi Zheng, Bing Han, Yong-Liang Wang

Journal of Electrochemistry

A new concept of seawater battery with electrochemical capacitance (SWB-EC) has been proposed using carbon fibre brush (CFB) as the cathode material, and three testing prototypes have been made accordingly. The discharge performances of the CFB before- and after-oxidation and Mg alloy sacrifice anode were studied by cyclic voltammetry and constant current discharge tests under steady state conditions. Results show that the oxidized CFB exhibits the pseudo-capacitive characteristic and its activity of oxygen reduction reaction (ORR) in stirred seawater highly increases, comparing with the non-oxidized CFB. The open circuit potential of Mg alloy sacrifice anode is -1.74 V, having the …

Electrochemical Fabrication Of The Ordered Polyaniline Nanowires Array, Yan-Xin Gao, Li-Chao Sun, Su-Yuan Xie, Kang Shi

Journal of Electrochemistry

The effects of electrochemical fabrication methods in different aniline concentrations on the morphologies of polyaniline, which was polymerized on the aligned-multi-walled carbon nanotubes electrode in H₂SO₄ or HClO₄ electrolyte solution, were investigated. It was demonstrated that the polyaniline nanowires would not be prepared by cyclic voltammotry, whereas the nanowires could be obtained by the potentiostatic method without forming the ordered array. Only when the aniline concentration in HClO₄ solution was high enough, the ordered polyaniline nanowires array could be fabricated by the constant current method.

Simultaneous Determinations Of Ascorbic Acid, Dopamine And Uric Acid At Ca/Gc Electrode, Ying Zhang, Wang Ren, Min-Jiao Li

Journal of Electrochemistry

The citric acid modified glassy carbon electrode (CA/GC) was constructed by potentiostatic technique and used for simultaneous determinations of ascorbic acid (AA), dopamine (DA) and uric acid (UA) by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The CA/GC electrode exhibits excellent electrocatalytic activity towards AA, DA and UA. The oxidation peaks are well separated with the potential differences between AA and DA, DA and UA, and AA and UA being 170, 130 and 300 mV, respectively, which is large enough to determine AA, DA and UA simultaneously. The catalytic peak currents obtained were linearly dependent on the concentrations of …

Cycle Lifetime Investigation Of Nickel Electrode Prepared By Electrochemical Impregnation For Applications In Aerospace Nickel Hydrogen Cells, Hai-Chang Zhang, Li-Xin Tan, Cheng Guo, Wen-Cheng Ming, Xue-Ying Ren

Journal of Electrochemistry

In this paper, the effects of overcharge, charge-discharge C rate and pore size on cycle lifetime of 4.5’ electrochemical impregnated nickel electrode were investigated. In the case of the electrode was overcharged to 170% of nominal capacity, the initial capacity of the electrode could be maintained 2.7 Ah up to 150 cycles without deterioration and a discharge capacity of 1.7 Ah (remaining 63% of 2.7 Ah) could be delivered after 300 cycles. Without overcharge, more than 300 charge-discharge cycles could be realized without loss of capacity and a discharge capacity of electrode could be maintained about 76% of initial capacity …

Ag Nanoparticles Self-Assembled Films On Iron Surface And Their Inhibition Properties, Zhe Zhang, Ming-Zi Jia, Le Ruan

Journal of Electrochemistry

The Ag nanoparticles were prepared in aqueous solutions through a chemical reduction method and transferred from water phase to toluene phase with the protection of 1-dodecanethiol (DDT). The polished iron electrode was immersed in the DDT-protected metal nanoparticles toluene solutions to form DDT/Ag nanoparticles self-assembled mixed films. Electrochemical methods such as electrochemical impedance spectroscopy and polarization curve measurement were used to study the inhibition properties of the self-assembled films in the 0.5 mol·L^-1 H₂SO₄ solution. The appearance of elements such as S and Ag from the XPS data identified the presences of DDT and Ag nanoparticles.

A Microfiber Coupler Tip Thermometer, Ming Ding, Pengfei Wang, Gilberto Bramilla

Articles

A compact thermometer based on a broadband microfiber coupler tip is demonstrated. This sensor can measure a broad temperature interval ranging from room temperature to 1283 degrees C with sub-200 mu m spatial resolution. An average sensitivity of 11.96 pm/degrees C was achieved for a coupler tip with similar to 2.5 mu m diameter. This is the highest temperature measured with a silica optical fiber device. (C)2012 Optical Society of America

The Art And Beauty Of Flight, Edmond Ing Huang Tan

The Hilltop Review

This picture nicely represents the art and gracefulness of flight with the beauty of sunset in a tranquil setting. In the picture is a powered paragliding, also known as paramotoring in the plains of Nebraska. The ability to fly both low and slow safely, the 'open' feel, the minimal equipment and maintenance costs, the portability, minimally regulated and requires no license are claimed to be this type of flying's greatest merits. Paramotors can be flown during any season of the year anywhere but not in high wind conditions which typically means at low Sun azimuths as shown in the picture …

Wmu Sunseeker Solarcar, Edmond Ing Huang Tan

The Hilltop Review

This picture was taken, at the racetrack the evening before the start of the North American Solar Challenge 2008 race in Plano, Texas. In this picture is the Sunseeker, Western Michigan University’s solar powered car that will race in the 2 week long, 2400miles long race from Plano, Texas to Calgary, Canada. Sunseeker was the only car in that race that feature a 2 electric motor drive system than the standard one electric motor drive system. Western Michigan University Sunseeker team brought back the sportsmanship award that year.