Engineering Commons^™

3d Electromagnetic Simulation Tool Exposure For Undergraduate Electrical Engineers: Incorporation Into An Analog Filters Course, Bobby B. Pheng

Master's Theses

With the growth of wireless communications, comes the need for engineers knowledgeable in 3D electromagnetic (EM) simulation of high-frequency circuits. To give electrical engineering students a better understanding of the behavior of electromagnetic fields, experiments including the use of 3D EM simulation software were proposed. Most students get lost in differential equations, curls, and divergences; this thesis aims to remedy that by exposing them to 3D EM simulation, which may motivate them toward further study in electromagnetics. Also, experience using EMPro is very beneficial for future RF/microwave/antenna engineers, as use of 3D EM simulation is becoming a requirement for this …

Evaluation, Design, And Testing Of Plc Data Logging System On Modified Pulling Tractor, Jared Evers

BioResource and Agricultural Engineering

This senior project involves the design and implementation of a data logging system on a modified pulling tractor, Mustang Fever. The project starts out a continuation of a previous project. The original goal of the project was to keep the Cal Poly Tractor Pull on the leading edge of innovation. The implementation of a sensor array and logging system on a modified pull tractor assists with the maintenance and tuning of the machine. The collected data is stored on a USB drive to allow analysis in the future.

The parameters collected by the system are: pressures, temperatures, and rotational speeds. …

Predictive Musculoskeletal Simulation Using Optimal Control: Effects Of Added Limb Mass On Energy Cost And Kinematics Of Walking And Running, Antonie J. Van Den Bogert, Maarten Hupperets, Heiko Schlarb, Berthold Krabbe

Mechanical Engineering Faculty Publications

When designing sports equipment, it is often desirable to predict how certain design parameters will affect human performance. In many instances, this requires a consideration of human musculoskeletal mechanics and adaptive neuromuscular control. Current computational methods do not represent these mechanisms, and design optimization typically requires several iterations of prototyping and human testing. This paper introduces a computational method based on musculoskeletal modeling and optimal control, which has the capability to predict the effect of mechanical equipment properties on human performance. The underlying assumption is that users will adapt their neuromuscular control according to an optimality principle, which balances task …

Development Of A Protocol To Measure Gene Expression In The Mouse Tibia, Daniel Hoover

Biomedical Engineering

Numerous molecular factors active in bone tissue direct fracture repair and remodeling which can be altered by disease conditions such as Peripheral Arterial Disease (PAD) and Osteoporosis. Methods of molecular biology are commonly applied to investigate the expression and role of these molecular factors. This project presents a robust three-step protocol for examining gene expression in the mouse tibia. The protocol begins with isolating RNA from a flash frozen tibia sample. The isolated RNA is reverse transcribed into cDNA. Finally, PCR is performed to indentify expressed genes. Establishing this protocol will allow further research into the mechanisms of bone remodeling …

Surveying First-Year Students Prior Conceptual Understanding Of Direct Current Resistive Electric Circuits: An Update, Aidan O'Dwyer

Conference papers

There is an increasing diversity of educational background of students entering Level 7 and Level 8 programmes in engineering in Irish third level education. Student reasoning about basic electricity concepts often differs from accepted explanations. The paper reports, analyses and reflects on the results of a multiple-choice diagnostic test to assess student understanding of such concepts (developed by Engelhardt and Beichner (2004) for U.S. high school and college students) taken by four cohorts of students, on the same DIT Level 7 engineering programme, from 2008-12 (n=106) and two cohorts of students, on the same DIT Level 8 engineering programme, from …

Energy Information Augmented Community-Based Energy Reduction, Kevin P. Hallinan, Harvey Enns, Stephenie Ritchey, Phil Brodrick, Nathan Lammers, Nichole Hanus, Mark Rembert, Tony Rainsberger

Mechanical and Aerospace Engineering Faculty Publications

More than one-half of all U.S. states have instituted energy efficiency mandates requiring utilities to reduce energy use. To achieve these goals, utilities have been permitted rate structures to help them incentivize energy reduction projects. This strategy is proving to be only modestly successful in stemming energy consumption growth. By the same token, community energy reduction programs have achieved moderate to very significant energy reduction. The research described here offers an important tool to strengthen the community energy reduction efforts—by providing such efforts energy information tailored to the energy use patterns of each building occupant. The information provided most importantly …

Nanostructured Ti1‑Xsxo2‑Yny Heterojunctions For Efficient Visible- Light-Induced Photocatalysis, Vinodkumar Etacheri, Michael Seery, Stephen Hinder, Suresh Pillai

Articles

Highly visible light active S, N co-doped anatase-rutile heterojunctions is reported for the first time. The formation of heterojunctions at a relatively low temperature and visible light activity are achieved through thiourea modification of the peroxo-titania complex. FT-IR spectroscopic studies indicated the formation of a Ti⁴⁺-thiourea complex upon reaction between peroxo-titania complex and thiourea. Decomposition of the Ti⁴⁺-thiourea complex and formation of visible light active S, N co-doped TiO₂ heterojunctions are confirmed using X-ray diffraction (XRD), Raman spectroscopy, transmission electron microscopy (TEM) and UV/Vis spectroscopic studies. Existence of sulfur as sulfate ions (S⁶⁺) …

Kentucky Department Of Vehicle Regulation Internet Applications Study, Andrew Martin, Jennifer Walton

Kentucky Transportation Center Research Report

The study identified 107 unique interactive services, and 13 unique information services on state vehicle regulation agency web sites. The average state has roughly 15 percent of all existing services. States with larger populations, number of registered vehicles and drivers tend to have more total services and transaction services. The general flow of the data indicates a fast level of growth, as companies and individuals embrace the efficiency and flexibility of online transactions. The W3C Unicorn Validator, Link Sleuth, Web Accessibility Checker and Hubspot Marketing Grader scores were combined to generate a web design score for each state. Washington received …

Mac's Fiesta: A Foreign Language Game For The Sifteo Platform, Karina Cordon

Computer Engineering

Mac’s Fiesta is a Spanish learning game designed on the Sifteo gaming platform for children ages four and up. The Sifteo gaming platform provides a new way of interacting with computers by giving users a set of tangible and interactive cubes. Each Sifteo cube has a clickable colored screen and can sense motion and adjacent blocks. Games on this platform are designed to encourage the development of core thinking skills. This project aims to explore how Sifteo cubes can be used for language learning as well as observe how effective they are as educational tools.

Cpe Senior Project Final Report: Roborodentia 2012 - Team Street Sweeper, Jason Miller, David Pascale

Computer Engineering

The Street Sweeper was a multi-disciplinary, autonomous robotics project constructed to compete in Cal Poly's Roborodentia XVII in 2012. The goal of the competition was to collect painted cat food cans in the team's goal area, with bonus points for stacking the cans. Street Sweeper was very much a budget robot, but due to good planning and strategy, managed to place 2nd in the competition.

Riley The Cat, Nicholas Zankich

Computer Engineering

There are many toys that exist that are comfort objects. Generally these are toys that are soft such as blankets, stuffed animals, and pillows. Robotic toys also exist such as games, interactive books, and instruments. There exists a crossover market that includes Furbys, Tomagachi pets, and Fur Real Friends. While being very popular, I believe that this crossover isn’t perfect, and that there is a lot of room for improvement. Riley (Figure 1) was created to make something that is both completely a robot and a comfort object.

Vibration Health Monitoring Of Gears, Markus Josef Scherer

Master's Theses

Monitoring the health of vibrating gears is important to ensure proper operation especially in potentially life-threatening structures, such as helicopters, nuclear power plants, and uninterruptible power supply transitions in hospitals. The most common monitoring technique is casing mounted accelerometers to measure vibration. In contrast, during the last few years acoustic monitoring techniques have also provided a few diagnostic methods for gear failure. Current diagnostic methods to indicate improper gear behavior use either existing vibration data, recorded from defective gear systems, or modern dynamic models predicting gear failure behavior.

This thesis uses dynamic models to indicate, predict, and diagnose healthy and …

Legacy Effects In Material Flux: Structural Catchment Changes Predate Long-Term Studies, Daniel J. Bain, Mark B. Green, John L. Campbell, John F. Chamblee, Sayo Chaoka, Jennifer M. Fraterrigo, Sujay S. Kaushal, Sherry L. Martin, Thomas E. Jordan, Anthony J. Parolari, William V. Sobczak, Donald E. Weller, Wilfred M. Wollheim, Emery R. Boose, Jonathan M. Duncan, Gretchen M. Gettel, Brian R. Hall, Praveen Kumar, Jonathan R. Thompson, James M. Vose, Emily M. Elliott, David S. Leigh

Civil and Environmental Engineering Faculty Research and Publications

Legacy effects of past land use and disturbance are increasingly recognized, yet consistent definitions of and criteria for defining them do not exist. To address this gap in biological- and ecosystem-assessment frameworks, we propose a general metric for evaluating potential legacy effects, which are computed by normalizing altered system function persistence with duration of disturbance. We also propose two distinct legacy-effect categories: signal effects from lags in transport and structural effects from physical landscape changes. Using flux records for water, sediment, nitrogen, and carbon from long-term study sites in the eastern United States from 1500 to 2000, we identify gaps …

Performance-Based Analysis Of A Reinforced Concrete Shear Wall Building, Garrett Richard Hagen

Master's Theses

PERFORMANCE-BASED ANALYSIS OF A REINFORCED CONCRETE SHEAR WALL BUILDING

Garrett Richard Hagen

In this thesis, a special reinforced concrete shear wall building was designed per ASCE 7-05, and then the performance was investigated using the four analysis procedures outlined in ASCE 41-06. The proposed building was planned as a 6-story office building in San Francisco, CA. The structural system consisted of a two-way flat plate and reinforced concrete columns for gravity loads and slender structural walls for seismic loads. The mathematical building models utilized recommendations from ASCE 41-06 and first-principle mechanics. Moment-curvature analysis and fiber cross-section elements were used in …

Regression-Based Prioritization And Data Modeling For Customized Civil Engineering Data Collection, Omar Kanaan

Masters Theses

Civil engineers frequently face the challenges of acquiring sufficient data to satisfy the informational needs of various decision making scenarios having time, budget, and resource constraints. This thesis focuses on exploring how statistical analysis of historical data sets can be used to improve the efficiency and effectiveness of future data collection activities in transportation engineering and construction project control. Pearson's correlation, multiple regression, Akaike information criterion, and Bayesian information criterion are applied to two cases of data collection and analysis to understand the relative importance of various parameters within each case. Case I analyzes National Bridge Inventory (NBI) data to …

Digital Graphic Equalizer Implemented Using An Fpga, Anthony Giardina

Electrical Engineering

A graphic equalizer is a device that adjusts the tonal quality of an audio signal. When sound is converted from a digital format to analog sound waves, there are amplification and transducing steps in-between the two formats. Common devices to perform these tasks are speakers, amplifiers, DACs, etc. Many of these devices exhibit a non-uniform frequency response over the range of human hearing. Thus, it is possible that certain frequency ranges of the audio signal will be amplified and others will be attenuated. To counteract this, an audio equalizer can be used to boost and attenuate certain frequency ranges within …

Multiple Input Single Output (Miso) Dc-Dc Converter For The Dc House Project, Owen Jong

Electrical Engineering

This senior project report explains the design of a Multiple Input Single Output (MISO) DC-DC converter for the DC House Project. MISO DC-DC converter interfaces multiple different power sources such as Wind and Solar Energy sources as the inputs to a DC house. The report demonstrates the functionality and the performance of the proposed converter using Flyback topology by showing the theoretical simulation and hardware testing results. Results show the ability of the proposed MISO converter to supply up to 150 Watts from three sources while maintaining maximum efficiency of 92% at full load.

Control System For Glucose Detector System, David Smith

Electrical Engineering

In this paper I design and test on a prove of concept level a control/timing circuit for a blood glucose detector built in a previous senior project. The specifications of the design given are to properly power the detector with a low power source. The design is completed on a transistor level basis using Cadence Virtuoso Software. The system is design from the ground up; designing, building, and testing smaller circuits first then combined into increasingly larger circuits till the completed circuit is finished. The design used to based off of the 555 Timer and uses differential pairs, CMOS designed …

Barrel Racer's Calculator, Hollie Kucera

Electrical Engineering

Barrel racing is a rodeo event in which a horse and rider attempt to complete a clover-leaf pattern around preset barrels in the fastest time. This sport combines the horsemanship skills of a rider and the horse’s athletic ability to safely and successfully maneuver around the three barrels (three fifty-five gallon metal drums) placed in an arena.

In barrel racing, the purpose is to make the run as fast as possible. An electric eye and timing system keep track of the time. The time starts when the horse and rider cross in between the electric eyes and ends when the …

Linear Precoding For Finite-Alphabet Inputs Over Mimo Fading Channels With Statistical Csi, Weiliang Zeng, Chengshan Xiao, Mingxi Wang, Jianhua Lu

Electrical and Computer Engineering Faculty Research & Creative Works

This paper investigates the linear precoder design that maximizes the average mutual information of multiple-input multiple-output fading channels with statistical channel state information known at the transmitter. It formulates the design from the standpoint of finite-alphabet inputs, which leads to a problem that is very important in practice but extremely difficult in theory: First, the average mutual information lacks closed-form expression and involves prohibitive computational burden. Second, the optimization over the precoder is nonconcave and thus easily gets stuck in local maxima. to address these issues, this study first derives lower and upper bounds for the average mutual information, in …

Design Of An Independent Star-Clip Organizer (Iso), Christopher Gonzales, Greg Lovasik, Daniel Silveira

Mechanical Engineering

Discussed below is a new concept to sort and deliver star clips for flight deck safety net manufacturing. Multiple methods were generated, along with the necessary research, and were narrowed down to a single concept: the tray-loading preprocess design, named ISO (Independent Star-Clip Organizer). The overall design has been finalized and designed. Due to budget constraints, an actual prototype was not built. However, the design of such a prototype is described by this report, backed with calculations and experimental testing.

Polygrasp: Reach; Myoelectric Prosthetic Hand Iteration, Devon Patrick Augustus, Mighells Blaed Deuel, Ian Noel Fraser, Nicholas Philip Moesser

Mechanical Engineering

Amputations are a common occurrence in soldiers returning home who have suffered the effects of IED and munitions explosions. For upper limb amputees, trans-radial amputations are the most common. Traditional hook devices do not offer an adequate level of normalcy for users, prompting the use of myoelectric devices. While current myoelectric devices do offer a more natural experience, they come with a host of other problems that makes their adoption by service personnel not desirable or not permitted by the VA. PolyGrasp Reach seeks to reduce weight and cost and improve performance. This addresses several of the issues with devices …

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Aerodynamic Test Platform For Human Powered Vehicle (Hpv), Spencer Wangerin, Spencer Lillywhite, Colburn Davis

Mechanical Engineering

The Aerodynamic Test Platform (ATP) for the Cal Poly HPV Club is a system that was designed by Cal Poly mechanical engineering students to measure aerodynamic characteristics of a human-powered vehicle (HPV). The HPV team desired a system that could quantify the lift, drag, and other aerodynamic qualities of a full scale HPV at various orientations in oncoming airflow. Established methods for determining aerodynamic characteristics include computational fluid dynamics (CFD) and wind tunnel testing of scaled models. The ATP was devised to simulate the test results given by a full-scale wind tunnel without requiring a wind tunnel large enough to …

Supermileage Chassis Dynamometer, Jose Garcia, Steve Janning, Timothy Lui, Kyla Purvis

Mechanical Engineering

This report describes the final design and analysis of a hydraulic chassis dynamometer as a testing tool for California Polytechnic State University, San Luis Obispo Supermileage Vehicle Team (CPSMV). Literature review was conducted to understand the various types of chassis dynamometers on the market as of the year 2011. After rigorous research, it was determined that a hydraulic system was the best system for a chassis dynamometer in terms of functionality, performance, and cost. Critical study of hydraulics, dynamometers, and data acquisition systems (DAQ) was followed by a complete design of a hydraulic system. The chassis dynamometer proposed in this …

California Olive Ranch Hedger, Tyler Enos, Seth Abbott, David Gamba

Mechanical Engineering

The purpose of this project is to evaluate the problems of the current KCI (Kingsburg Cultivator Incorporated) olive tree hedger in use at California Olive Ranch (COR) in Artois, CA, and then correct these problems which should yield a better performing, more efficient, and reliable machine. These problems include: the hydraulic oil temperature getting too high, the saw blades not having enough horsepower, and poor cutting performance due to operator error as well as terrain variations.

Main Reduction Gear Debris Identification And Removal Device, Gordon Cline, Alex Tittiger, Michael O'Brien

Mechanical Engineering

This report details the development of a tool to remove objects and debris from a large gearbox found on ships of the United States Navy, specifically to be used by NAVSEA. The tool is to be used in situations where an object or contaminant cannot easily be removed or found without completely disassembling the gearbox. This will be done using a boom arm, a cable, a gripper and a borescope. This combination will allow for a large amount of mobility and versatility when searching for the object or contaminant, which is necessary for use in different gearboxes. The process we …

Cryogenic Heat Switch, Daniel Brodkey, Esteban Ruiz, Cristal Vasquez

Mechanical Engineering

A prototype cryogenic heat switch capable of transferring heat at cryogenic temperatures, while decoupling to prevent irreversible heat damage and minimizing parasitic heat loads, is to be developed for the Jet Propulsion Laboratory. Various material properties and cryogenic heat transfer processes will be investigated to determine the best solution for this project. A working proof of concept model will be constructed that may eventually be integrated onto a spacecraft’s passive cooler systems to protect them from the irradiation emitted by the sun, from the albedo of planets, and other malicious heat sources.

Design Of A Releasable Snowboard Binding, Rex Crossen, Brian Kruse, Timothy Scott

Mechanical Engineering

A releasable snowboard binding will be proposed to our sponsor. This binding will allow the user to release and engage on demand for aerial tricks, comfort, and increased safety. The releasable snowboard binding we will come up with will be revolutionary within the snowboard industry and make current bindings old and inferior.

Model Performance Sensitivity To Objective Function During Automated Calibrations, Misgana Muleta

Civil and Environmental Engineering

Previous studies have reported limitations of the efficiency criteria commonly used in hydrology to describe goodness of model simulations. This study examined sensitivity of model performance to the objective function used during automated calibrations. Nine widely used efficiency criteria were evaluated for their effectiveness as objective function, and goodness of the model predictions were examined using 13 criteria. Two cases (Case I: Using observed streamflow data and Case II: Using simulated streamflow) were considered to accomplish objectives of the study using a widely used watershed model (SWAT) and good-quality field data from a well-monitored experimental watershed. Major findings of the …