Engineering Commons^™

Conductive Concrete For Electromagnetic Shielding – Methods For Development And Evaluation, Aaron P. Krause

Department of Computer Electronics and Engineering: Dissertations, Theses, and Student Research

This research investigates the development and evaluation innovative methods for the use of conductive concrete as an electromagnetic shield. New testing methods are developed to determine the best conductive components to use in the design of a concrete mixture for shielding that shows the best promise. The conductive concrete mixture has the potential to provide electromagnetic shielding that is cost-effective in terms of construction, operation, and maintenance compared to conventional approaches. Two testing methods, Small Sample Testing and Large Slab Testing, are developed based on standardized testing methods that have been modified for the testing of conductive concrete mixtures. As …

Pc-Based Automated Control System For Jordan Northern Grain Silo, Salem Al-Agtash

Computer Science and Engineering

This paper presents a PC-based automated control system operation of the Northern Grain Silo of Jordan. The system connects to a PLC (programmable logic controller) device, and combines operator interface, PLC programming and monitoring functions into one platform. The PLC portion handles direct operations control, while the PC portion handles interfacing and data intensive functions. A simulation package is developed. The package generates a graphical user interface for real-time graphic animations of the Grain Silo operation. We discuss anticipated benefits of such a system and phases of implementation.

Application Of Response Surface Methodology And Central Composite Design For 5p12-Rantes Expression In The Pichia Pastoris System, Frank M. Fabian

Department of Chemical and Biomolecular Engineering: Dissertations, Theses, and Student Research

Pichia pastoris has demonstrated the ability to express high levels of recombinant heterologous proteins. Protein expression is enhanced during fermentation at high cell density. However, the level of expression is mainly regulated by fermentation operation factors. This research is directed to investigate the effect of methanol growth rate, temperature and pH in the expression of the total 5P12-Rantes concentration, expression of active 5P12-Rantes and Specific yield using the response surface methodology and central composite design.

The response surface methodology, RSM, has been used successfully used by Zhang, W. and Ian, M. to optimize the cell density and fermentation process. The …

Investigation On Thermo-Mechanical Instability Of Porous Low Dielectric Constant Materials, Emil Hyunbae Zin

Material Science and Engineering Dissertations - Archive

This study investigates the structural stability of porous low dielectric constant materials (PLK) under thermal and mechanical load and the influence of contributing factors including porosity as intrinsic factor and plasma damage and moisture absorption as extrinsic factors on thermo-mechanical instability of PLK in advanced Cu/PLK interconnects. For this purpose, a ball indentation creep test technique was developed to examine the thermal and mechanical instability of PLK at relevant load and temperature conditions in the interconnect structure. Our exploration with the ball indentation creep test found that PLK films plastically deforms with time, indicating that viscoplastic deformation does occur under …

First-Principles Studies On N-Type And P-Type Doping In Cuprous Oxide, Qiong Bai

Material Science and Engineering Dissertations - Archive

We have performed studies on n-type and p-type cuprous oxide with and without doping by first principles methods. Generalized Gradient Approximation (GGA) is used for the geometry optimization. The total energy and the final electronic structure calculations are conducted using the nonlocal screened Heyd-Scuseria-Ernzerhof (HSE) hybrid density functionals approach for cuprous oxide. The HSE hybrid density functionals overcome the shortcoming of GGA, which gives a much reliable value of the band gap. The formation energies of native point defects in undoped cuprous oxide have been studied by HSE hybrid functional theory in two conditions, which are vacuum based condition and …

Properties Of Concrete With Tire Derived Aggregate And Crumb Rubber As A Ligthweight Substitute For Mineral Aggregates In The Concrete Mix, Gideon Momanyi Siringi

Material Science and Engineering Dissertations - Archive

Scrap tires continue to be a nuisance to the environment and this research proposes one way of recycling them as a lightweight aggregate which can substitute for mineral aggregates in concrete. Aggregates derived from scrap tires are often referred to as Tire Derived Aggregate (TDA). First, the focus is how much mineral aggregate can be replaced by these waste tires and how the properties of concrete are affected with the introduction of rubber. This is being mindful of the fact that for a new material to be acceptable as an engineering material, its properties and behavior has to be well …

Growth Mechanism And Interface Effects On Microstructure Of Perovskite-Type Barium Titanate-Based Epitaxial Films, Jie He

Material Science and Engineering Dissertations - Archive

This work was motivated and focused on the growth mechanism, microstructures and interfaces of barium titanate, BaTiO3 (BTO), based epitaxial thin films. Transimission electron microscopy (TEM), high resolution TEM (HRTEM), electron diffraction (ED) have been mainly employed in this study for microstructure investigations of BTO-based epitaxial thin films with the assistance of other materials characterization methods, such as X-ray diffraction (XRD), atomic force microscopy (AFM), Nanoindentation testing, etc. As a basic studying model, epitaxial BTO films were first deposited on the (001) MgO substrate using RF magnetron sputtering to provide fundamental knowledge of the film growth for BTO based thin …

Fabrication And Characterization Of Polylactic Acid And Polylactic Acid/Multi-Walled Carbon Nanotube Nanofibers Through Centrifugal Spinning, Richard Patlan

Theses and Dissertations - UTB/UTPA

Biocompatible polymer nanofibers hold great potential in the biomedical engineering field. Their biodegradable nature and enhanced properties could help solve a wide array of health related problems, particularly in the areas of tissue regeneration, drug delivery, and biosensor design. The novel ForcespinningTM method allows the production of submicron fibers without many of the drawbacks found in electrospinning, while also providing a substantial increase in fiber production. The aim of the study was to utilize this method to fabricate non-woven nanofibrous mats composed of polylactic acid (PLA) and polylactic acid/multi-walled carbon nanotube composite fibers. The morphology, thermal properties, and crystalline structure …

Development Of A Vibration And Temperature Measurement Device For Railroad Bearings, Andrea P. Arguelles

Theses and Dissertations - UTB/UTPA

Bearing related derailments cause very high cost and inconvenience to the railroad industry. Various wayside detection systems have been implemented to assess bearing condition and prevent premature failure. However, current devices fail to determine the internal condition of bearings or provide insight regarding the danger and severity of defects and abnormalities that may be present. To this end, a device combining both temperature and vibration detection was designed to be embedded in railroad bearing adapters. In order to efficiently design a railroad bearing condition-monitoring system, two factors that must be considered are the capabilities available to operate the different sensors …

Detecting Copper Residues In Sediments From Aquatic Copper-Based Pesticide Applications, Ben Willis

All Theses

Copper-based algaecides and herbicides are commonly used to mitigate risks of problematic algae and weeds, however there are concerns regarding copper accumulation from treatments. Modeling and laboratory experiments can be used to predict copper accumulation and measurement in sediments, as well as benthic invertebrate responses following treatments. Modeling was used to estimate copper residual concentrations in sediments from algaecide and herbicide treatments. Reported and measured method detection limits (MDLs; minimum concentration of an analyte of interest that can be measured with 99 percent confidence in a specific matrix using an analytical method) were compared to model estimated copper residual concentrations …

Evaluation Of Rubber Modified Porous Asphalt Mixtures, Kimberly Lyons

All Theses

A porous pavement is a type of sustainable pavement that allows stormwater to infiltrate through the pavement into the natural soil bed. Rubber modified binder is the combination of regular asphalt binder mixed with ground crumb rubber, which is derived from used rubber tires by shredding or grinding the tires into small fragments. This research investigated the effects of rubber modified binder on the performance properties of porous asphalt mixtures, which include draindown, porosity, permeability, abrasion resistance, moisture susceptibility, and rutting resistance.
The addition of cellulose fibers has been used to increase the optimum binder content of porous asphalt mix …

Syntheses, Characterization, And Applications Of Injectable Citrate-Based Mussel-Inspired Biodegradable Adhesive (Icmba) Polymers And Hydrogels, Mohammadreza Mehdizadeh

Material Science and Engineering Dissertations - Archive

Tissue adhesives are increasingly gaining more popularity in various areas of biomedical applications. They are utilized as surgical adhesives, as a replacement or adjunct to conventional wound closure and bleeding control techniques such as suturing, as well as in other applications such as tissue engineering and drug delivery.Unfortunately, the existing surgical adhesives are not ideal for wet tissue adhesion required in many surgeries such as those for internal organs. Developing surgical adhesives with strong wet tissue adhesion, controlled degradability and mechanical properties, and excellent biocompatibility has been a significant challenge. Herein, learning from nature, we report a one-step synthesis of …

Aerospace Section, Barbara A. Williams

Sci-Tech News

No abstract provided.

Alternative Energy Sources - Integration Of Power Generation Systems Into A Microgrid At Clemson University And An Atmospheric Thermodynamic Driven Mechanical Clock, Shreyas Patel

All Theses

Non-renewable energy sources such as coal, crude oil, and natural gas are being consumed at a brisk pace which is promoting a worldwide energy crisis. The burning of fossil fuels produces greenhouse gases such as carbon dioxide and nitrous oxides as well as soot which contribute to atmospheric pollution. Although fossil fuels will continue to be available for many decades, the amount of petroleum remaining in the earth and its associated cost remains an open issue. The utilization of green energy such as solar and wind offer renewable and pollution free sources. A worldwide shift is slowly underway towards the …

Standardization Of Process Sheet Information To Support Automated Translation Of Assembly Instructions And Product-Process Coupling, Matthew Peterson

All Theses

The design and manufacture of large scale systems, particularly automobiles, is a process that requires collaboration across multiple disciplines. This collaboration is facilitated through efficient and effective data and knowledge storage and transfer. Specifically, the data associated with the final assembly of the vehicle should be generated, organized, and distributed in such a manner that each user of the data is able to use it effectively. Furthermore, the structure for the assembly data should be robust and reliable such that it fosters consistency among various planners for multiple vehicle platforms that are assembled all around the world. This research aims …

The Control Of Nitrogenous And Carbonaceous Disinfection Byproduct Precursors With Magnetic Ion Exchange, Xiaojie Gan

All Theses

The objective of this study was to examine the potential of the magnetic ion exchange (MIEX®) process to remove nitrogenous disinfection byproduct (N-DBP) precursors while minimizing carbonaceous DBP (C-DBP) precursors in different water matrices. In the first phase of the study, the MIEX® process was tested in raw dinking waters and waters impacted effluent from wastewater treatment plant. Samples were collected from several drinking water/wastewater treatment plants in South Carolina. The effluent impacted source waters were prepared by mixing treated wastewater effluents with a drinking water. For all samples, formation potential (FP) tests were conducted for regulated trihalomethanes (THMs), haloacetic …

Note: A Transimpedance Amplifier For Remotely Located Quartz Tuning Forks, Ethan Kleinbaum, Gabor Csathy

Birck and NCN Publications

The cable capacitance in cryogenic and high vacuum applications of quartz tuning forks imposes severe constraints on the bandwidth and noise performance of the measurement. We present a single stage low noise transimpedance amplifier with a bandwidth exceeding 1 MHz and provide an in-depth analysis of the dependence of the amplifier parameters on the cable capacitance. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4769271]

Prediction Of Compressive Creep Bhaviour In Flexible Polyurethane Foam Over Long Time Scales And At Elevated Temperatures, Conor Briody, Barry Duignan, Stephen Jerrams, Stephen Ronan

Articles

Compressive creep gradually affects the structural performance of flexible polymeric foam material over extended time periods. When designing components, it is often difficult to account for long-term creep, as accurate creep data over long time periods or at high temperatures is often unavailable. This is mainly due to the lengthy testing times and/or inadequate high temperature testing facilities. This issue can be resolved by conducting a range of short-term creep tests and applying accurate prediction methods to the results. Short-term creep testing was conducted on viscoelastic polyurethane foam, a material commonly used in seating and bedding systems. Tests were conducted …

Influence Of Casting Techniques On Hardness, Tarnish Behavior And Microstructure Of Ag-Cu-Zn-Si Sterling Silver Jewelry Alloys, C. Chanmuang, W. Kongmuang, J.T.H. Pearce, T. Chairuangsri

Journal of Metals, Materials and Minerals

The effects of Zn and Si on the hardness, tarnish resistance and microstructures of experimental Ag-Cu-Zn-Si alloy were investigated by means of vickers hardness, tarnish testing, optical and scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The various compositions of 935 sterling silver alloys produced by different casting techniques, investment (lost wax) process and metal mould casting, were compared. An induction casting machine with a vacuum system was used for investment casting at 1,025C with the mould temperature at 600C whereas a LPG/oxygen single flame tip torch was used for the metal mould process. Vickers hardness of the samples …

Bismuth Vanadate (Bivo4) Powder Prepared By The Sol-Gel Method, P. Pookmanee, S. Kojinok, S. Phanichphant

Journal of Metals, Materials and Minerals

Bismuth vanadate (BiVO4) powder was prepared by the sol-gel method. Bismuth nitrate and ammonium vanadate were used as the starting precursors with mole ratio of 1:1 in ethanol at 70C for 1 hour. The obtained sol was changed to the yellow gel after addition of deionized water and acetic acid. The yellow gel was dried at 100C for 48 h and calcined at 400-600C for 2 hours. The phase of BiVO4 powder was studied by X-ray diffraction (XRD). The morphology of BiVO4 powder was investigated by scanning electron microscopy (SEM). The element composition of BiVO4 powder was indicated by energy …

Preparation And Characterization Of Highly Filled Graphite-Based Polybenzoxazine Composites, A. Pengdam, S. Rimdusit

Journal of Metals, Materials and Minerals

This research aims to study suitable preparation methods and to characterize highly filled graphite composites using polybenzoxazine as a matrix. The high loading of graphite filler was attained in the range of 40 to 80% by wt. due to the very low a-stage viscosity of the benzoxazine resin (BA-a) used. The suitable condition for the compression molding of the highly filled graphite-polybenzoxazine (PBA-a) composites was at temperature of 200°C, and pressure of 15 MPa in the hydraulic hot-press machine for 3 hours to assure a fully cured specimen. The densities of the obtained composites were found to be in a …

Study Of Dynamic Vulcanized Pla/Enr Tpv Filled With Various Organic Modified Mmt (Ommt), C. Thongpin, N. Kuttanate, K. Kampuang, N. Suwanwanit

Journal of Metals, Materials and Minerals

In this research, we investigated the crystallization behavior of PLA and properties of PLA/ENR thermoplastic vulcanizates (TPVs). ENR was compounded with phenolic resin and with PLA at the blend ratio of 40/60 by using an internal mixer at 170°C and rotor speed of 70 rpm. Three types of organic modified montmorillonite (OMMT) which are Cloisite® 15A, Cloisite® 20 A and Cloisite® 30B were also added at various contents during mixing. The TPVs were pressed to form thin film in a compression molding machine and cooled down under pressure for 10 minutes. Crystallization behavior, thermal properties and morphology of TPVs were …

Explosively Formed Projectile Soft-Recovery Force Analysis, Laurin Bookout, Phillip R. Mulligan, Jason Baird

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The design of a soft-recovery system is critical to a researcher's ability to analyze hypervelocity projectiles. The researcher may decide to use one method over another based on several criteria, including whether or not non-deformed projectile measurements are required. This report analyzes the forces two different soft-recovery methods impart on the projectiles collected. Method 1 utilized three polyethylene water barrels placed “end-to-end” horizontally, providing 2.6 meters (9 feet) of water to stop the projectile. Method 2 is a modification of the soft-recovery method utilized in “Soft-Recovery of Explosively Formed Penetrators” by Lambert and Pope. This method utilizes a series of …

Acuta Enews December 2012 Vol. 41, No. 12

ACUTA Newsletters

In this issue...

Strategic Planning & Tampa in January

ACUTA Is Looking for a Few Good Coordinators

Wi-Fi Goes Gigabit-802.11 ac

Info Links

Preparing the Workplace for "Deep Diversity"

Get Your Logos Here!

Webinar: Universal Service & Royalty Payments Due

Using Social Media to Connect

Thanks to Our 2012 Exhibitors

Number 10 on a List of 10 Hard Things IT Must Learn to Accepts

Welcome New Members

Check It Out

Machining Stability Of Wire Edm Of Titanium, Farnaz Nourbakhsh

Department of Industrial and Management Systems Engineering: Dissertations, Theses, and Student Research

This work presents an experimental investigation of wire electro-discharge machining (WEDM) of titanium alloy. The outstanding characteristics of titanium alloys such as their compatibility and noticeable physical, mechanical and biological performances has led to increased application of them in various industries especially in biomedical industries over the last 50 years. However, due to low thermal conductivity of titanium and its alloys and their reactivity with cobalt in most tool materials, there are some difficulties in machining titanium and its alloys by conventional machining. On the other hand, unconventional machining processes especially Wire Electrical Discharge Machining (WEDM) are more appropriate techniques …

A Simulation-Based Decision Support System To Model Complex Demand Driven Heathcare Facilities, Amr Arisha, Michael Thorwarth

Conference papers

Simulating healthcare processes is a sophisticated endeavor. Treatment processes and patient arrival patterns differ significantly in their statistical attributes and implicate a high degree of variability. In addition, there are several types of interconnected processes of medical staff involved that accompany a patient’s journey through the healthcare facility. Replicating this behavior with process flow models in a discrete event simulation model is highly complex and therefore difficult to create while maintaining a high degree of precision. A framework is thus introduced which delivers an algorithm that allows to implement Multiple Participant Pathway Modeling (MPPM) under the consideration of Flexible Resource …

Multi-Citeria Framework For An Emergency Department In An Irish Hospital, Waleed Abo Hamad, Amr Arisha

Conference papers

Health research is one of these priorities in every economy and through this research an emphasis will be put on translational research in the context of more sustainable and efficient healthcare system (translation of operations management practices to clinical applications). Healthcare systems in general and Emergency Departments in particular around the world are facing enormous challenges in meeting the increasingly conflicting objectives of providing wide accessibility and efficiency while delivering high quality and prompt services. The proposed framework integrates simulation modeling, balanced scorecard, and multi-criteria decision analysis aiming to provide a decision support system to emergency department managers. Simulation outputs …

Using Player Profiling To Enhance Dynamic Difficulty Adjustment In Video Games, Aaron Burke

Computer Engineering

Video games have certainly come a long way since the days of pong. From humble beginnings of the first arcade machines they have bloomed into a multi-billion dollar industry and a global force to be reckoned with. Just like with movies there are enough genres out there to fit any demographic of gamer, and that’s not even just the game’s content but also the gameplay.

Unlike other types of media though, games are meant to be interacted with and played, which brings up new issues with accessibility and keeping things interesting for different levels of skill. Dynamic game difficulty adjustment …

Micro-Grid Wind Energy System, Aaron Steinkraus, Brian Huntziker, Cesar Hurtado

Mechanical Engineering

With the completion of a 3.5kW wind turbine located on Esculea Ranch, the power generated from the turbine was dissipated through electric resistance heaters. ABC Wind was given the task to design, build, and implement a system what will efficiently use the turbine’s harnessed power. After interviewing with the Beef Operations Manager of Escuela Ranch, it was decided to use the turbine’s power to supply supplementary water to anywhere on the ranch where and when needed by grazing cattle. The purpose of this project was to research, design, build and implement a system that would harness the generated power and …

Dynamic And Static Effects In Wetting Of Capillaries And Fibers, Taras Andrukh

All Dissertations

This research is centered on the analysis of static and dynamic effects of wetting of single capillaries and fibers. We discuss specifics of the capillary rise and drop-on-fiber techniques and develop new methods of characterization of surface energy of single fibers when its contact angle varies between zero and ninety degrees. The contact angles were evaluated and compared for different substrates. We study the dynamics of the meniscus formation inside and outside of capillaries and fibers. We develop a mathematical model of liquid uptake by capillaries and analyze the factors affecting liquid uptake. The derived fundamental equation describes the dynamics …