Engineering Commons^™

Relating Burst Pressure To Seal Peel Strength In Pouches, William Bernal

All Theses

This work was aimed at studying the relationship between burst pressure and seal peel strength. Past researchers developed a force balance equation based on the analysis of a force diagram to relate burst pressure to seal strength. The theoretical formula S=P(D/2) (S=Seal Strength, P=Burst Pressure, D=Restraining Plate Gap) has been studied by past researchers with contrasting results.
The theoretical formula was tested by varying dwell time to produce seals of varying strength. Pouches were burst tested at each of these dwell times to obtain burst pressures, burst peeling times, and burst locations. Corresponding peel tests were performed with crosshead speeds …

The Formulation Of A Bone Targeted Drug Delivery System Of Poly(Glycolic Acid)-Poly(Ethylene Glycol) Coated Hydroxyapatite Nanoparticles For The Delivery Of Statins, Erika Jelen

All Theses

Bone is a form of mineralized connective tissue that provides strength and rigidity to the skeleton. The two primary components within bone tissue are an organic extracellular matrix, containing type I collagen, and an inorganic mineral component composed mainly of calcium phosphate hydroxyapatite crystals. Over time the microarchitecture of bone can break down due to a variety of different factors, mainly the onset of osteoporosis in post-menopausal women, Paget's disease, and the experience of a loss of gravity during space flight. Currently there are about ten million people in the United States alone suffering from osteoporosis.
The prevention of further …

Remanufacturing Cleaning Process Evaluation, Comparison And Planning, Ozan Yagar

Theses and Dissertations - UTB/UTPA

This thesis aims to combine previous research on remanufacturing cleaning processes and applications into a single decision-making tool, in the form of software, which a remanufacturer can use to find a cleaning system that matches their specific demands. This thesis will provide an in-depth review of each cleaning process, the chemicals used in those processes, and the contamination types for which they were developed. This research also provides evaluation and comparison that assists remanufacturers in designing their cleaning systems. Finally, there will be a description and demonstration of the software. The ultimate goal is to find correct cleaning process to …

A Case Study For Financial Feasibility Of Automated Costing Support In A Small Machine Shop, Benito A. Gonzalez

Theses and Dissertations - UTB/UTPA

A knowledge-based cost estimating expert system is chosen by a Mexican machine shop. Differences between the traditional experience-based system employed and the automated system are studied. Data is gathered to analyze time effectiveness, accuracy and payback of the software. Data from seventy part models is recorded to study the time experiment, and data from fifty part models is used to study the accuracy and consistency. Data is analyzed by calculating mean, standard deviation, and test of hypothesis. The results indicate that the software is faster than the traditional quoting system; however, the payback point is high. Also, results show the …

Effects Of Oxygen Deprivation On Pilot Performance And Cognitive Processing Skills: A Pilot Study, David Francis Shideler

Doctoral Dissertations and Master's Theses

According to Federal Aviation Administration (FAA) regulations, pilots flying above 14,000 ft. are required to use supplemental oxygen. The purpose of this study was to examine how oxygen deprivation below 14,000 ft. affects pilot performance using the Frasca Mentor Advanced Aviation Training Device (AATD), and cognitive processing skills using the Automated Neuropsychological Assessment Metrics (ANAM(TM)) cognitive test. The study was conducted in a Normobaric High Altitude Laboratory at simulated altitudes of 5,000 ft. and 14,000 ft. In this pilot study, only five participants were tested; non-significant results of the analysis were anticipated; however, as oxygen levels decreased and time of …

Micro Hydroelectric Power Generation, Roberto Arraya Saenz

Chemical Engineering Undergraduate Honors Theses

MICRO-HYDRO ELECTRIC POWER GENERATION Roberto Arraya Department of Chemical Engineering – Honors Thesis ABSTRACT A major industrial water user in New Mexico discharges approximately 3.8 million gal of wastewater per day. The topology of the site provides an elevation difference of about 150 ft between the plant site and the entrance to the municipal sewage line; this flow and elevation difference is sufficient to produce about 40 kW of electrical power using a water turbine/electrical generator set to extract power from the flowing stream. This report includes designs and economic analyses for two distinct cases. One case is based on …

Measuring Sustainability, Evan A. Thomas

Mechanical and Materials Engineering Faculty Publications and Presentations

The World Health Organization estimates that 884 million people do not have access to safe sources of drinking water. Meanwhile, about half of the world's population continues to use unsustainable, biomassbased energy sources for indoor fuel, leading to extensive deforestation, harmful indoor air emissions, and in many cases upper respiratory disease and high commodity costs for impoverished families. Exacerbating these problems are the international effects of climate change, expected to significantly impact developing countries by changing water and energy quality and availability. International development organizations work tirelessly to address these challenges. However, many efforts struggle with achieving long-term sustainability; many …

A Mean Curvature Model For Capillary Flows In Asymmetric Containers And Conduits, Yongkang Chen, Noël Tavan, Mark M. Weislogel

Mechanical and Materials Engineering Faculty Publications and Presentations

Capillarity-driven flows resulting from critical geometric wetting criterion are observed to yield significant shifts of the bulk fluid from one side of the container to the other during "zero gravity" experiments. For wetting fluids, such bulk shift flows consist of advancing and receding menisci sometimes separated by secondary capillary flows such as rivulet-like flows along gaps. Here we study the mean curvature of an advancing meniscus in hopes of approximating a critical boundary condition for fluid dynamics solutions. It is found that the bulk shift flows behave as if the bulk menisci are either “connected” or "disconnected." For the connected …

Engineering Performance Of Polymer Amended Soils, Gary E. Welling

Master's Theses

A laboratory test program was undertaken to evaluate a series of engineering properties over a range of soil types; amendment types and addition rates; and moisture contents to enhance understanding of the engineering significance of polymer amendment. Four soils were manufactured and tested with varying ranges of fines and plasticity. A proprietary elastic copolymer was tested at addition rates of 0.5% to 2.5% (dry weight basis). Cement was tested at addition rates of 1% to 4%. Lime was tested at an 8% addition rate. Water addition rates ranged from 4% dry of optimum to 4% wet of optimum. Engineering properties …

Scale Model Shake Table Testing Of Shallow Embedded Foundations In Soft Clay, Steven Kuo

Master's Theses

This research involves shake table testing of 1g scale models that mimic the coupled seismic response of a structure on a shallow mat foundation and foundation soil (known as soil-foundation-structural-interaction or SFSI). In previous research, SFSI effects have been quantified through analytical models, numerical analyses, and limited field data. This research works towards increasing the amount of empirical data through scale model shake table testing. A suite of earthquake time histories is considered in evaluating a nominal 10^th scale soil-structure model using a flexible wall barrel on a 1-D shake table. San Francisco Young Bay Mud (YBM) is used …

Touchspice Vs. Reactive-Spice: A Human-Computer Interaction Perspective, Joshua Martin O'Hara

Master's Theses

Traditional SPICE simulation tools and applications of circuit theory lack real-time interaction and feedback. The goal of this thesis was to create an interactive physical environment to allow the manipulation and simulation of discrete electrical components in near-real-time while optimizing and streamlining the human-computer interaction (HCI) elements to make the user experience as positive and transparent as possible. This type of HCI and near-real-time simulation feedback would allow for the instant realization of how the parameters of each discrete component or hardware module affect the overall simulation and response of the circuit.

The scope of this thesis is to research, …

Thermo-Mechanical Modeling Of The Electrically-Assisted Manufacturing (Eam) Technique During Open Die Forging, Wesley Salandro

All Dissertations

This thesis contains all of the steps which allow the Electrically-Assisted Manufacturing (EAM) technique to be experimentally explored and analytically modeled for an electrically-assisted forging operation. Chapter 1 includes the problem statement, proposed solution, and literature reviews on EAM. Chapter 2 describes a thorough background on the EAM technique, highlights prior EAM research, and explains the research approach taken for this thesis. The coupled thermo-mechanical modeling strategy, along with the introduction of the Electroplastic Effect Coefficient (EEC) is provided in Chapter 3. Chapter 4 explains the two different approaches to determine the EEC profiles when modeling a particular metal. The …

Investigating The Role Of Mechanosensitive Ion Channels In Urothelial Cell Pressure Mechanotransduction, Shawn Olsen

All Dissertations

Overactive bladder (OAB) is a bladder disorder that is characterized by bladder storage symptoms of urgency with or without urge incontinence, frequency, nocturia, and, as of 2003, affected approximately 16.5% of adults in the United States with an annual treatment cost of over $65 billion. While therapies are available to mitigate the symptoms of OAB, there are no treatments for the cause of OAB, due to the lack of understanding of the etiology of the disorder. Recent research has provided evidence that the bladder urothelium is not just a passive barrier, but is also sensitive to various chemical and mechanical …

Laboratory Characterization And Theoretical Analysis Of Contaminant Mass Transfer, Xiaoling Liu

All Dissertations

Chlorinated volatile organic compounds (CVOCs) in fractured, low permeability material can be a long-term source of groundwater contaminants and they are among the most difficult remediation challenges. Thermal methods are a possible remediation option, where heat is used to boil water and the volatile compounds are stripped out by partitioning into the resulting water vapor. Theoretical analysis indicates that only a small fraction of pore water removal may lead to a significant geometric reduction in the dissolved concentration [(Udell(, 1998]. Previous modeling studies [(Falta and Murdoch(, 2011; (Pruess(, 1983] suggest that a lower permeability limit exists for effective mass transfer …

On Simulation And Modeling Of Turbulent Non-Premixed Reacting Shear Flames At Low And High Pressure, Justin Foster

All Dissertations

A database of simulations of fundamental turbulent H2/O2 and H2/Air shear layer flames has been developed using the direct numerical simulation technique in which all length and time scales of a flow are fully resolved without resort to turbulence modeling. The formulation includes the fully-compressible form of the governing equations, a pressure dependent detailed chemical kinetics scheme (9 species, 19 steps), a cubic real gas equation of state, realistic property models, and generalized heat and mass diffusion models. Simulations were conducted for a temporally developing shear layer geometry and cover a wide range of initial pressures (1 atm < P < 125 atm) and flame Reynolds numbers (850 < Re < 4500). These supercomputing simulations are the largest yet performed for high pressure conditions to the author's knowledge. Computational requirements for the largest simulations included mesh sizes of ~3/4 billion grid points and ~2.2 million CPU-hrs conducted on nearly 4,000 CPU cores on Clemson's Palmetto cluster.

The database …

Propagation Of Uncertainty In Light-Frame Wood Buildings, Seyed Masood Hassanzadehshirazi

All Dissertations

Light-frame wood construction is the most common form of construction for residential and low-rise commercial buildings (e.g. hotels and motels) in North America. In these buildings, shearwalls are the primary systems resisting lateral loads induced by earthquakes and winds. Past earthquake events have revealed that the structural performance of nominally identical light-frame wood buildings varied significantly. Although much research has been conducted investigating the uncertainty in the performance of wood shearwalls and buildings under earthquake loading, the focus of many of these studies was on the uncertainty due to the earthquake motions, referred as earthquake-to-earthquake uncertainty, the influences of variability …

Analysis Of Fiber Bragg Gratings For Ultrasonic Detection, Tongqing Liu

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Fiber optic sensors became an emerging technique to detect ultrasonic emissions in the last decade. Their light weight, immunity to electromagnetic interference and capacity of being multiplexed make them defeat their electronic counterparts in various applications. In this thesis we presented a novel fiber optic ultrasonic sensor based on pi phase shift fiber Bragg gratings. Numerical simulations were performed to study the characteristics of pi phase shift fiber Bragg gratings impinged by ultrasonic waves. The coupling theory was introduced to analyze the change of fiber Bragg gratings when impinged by ultrasonic waves, and the transfer matrix method was utilized to …

Routing Over The Interplanetary Internet, Joyeeta Mukherjee

School of Computing: Dissertations, Theses, and Student Research

Future space exploration demands a Space Network that will be able to connect spacecrafts with one another and in turn with Earth's terrestrial Internet and hence efficiently transfer data back and forth. The feasibility of this technology would enable common people to directly access telemetric data from distant planets and satellites. The concept of an Interplanetary Internet (IPN) is only in its incubation stage and considerable amount of common standards and research is required before widespread deployment can occur to make IPN feasible.

We provide a comprehensive survey that presents a picture of the current space networking technologies and architectures. …

Statistical Software Properties: Definition, Inference And Monitoring, Javier A. Darsie

School of Computing: Dissertations, Theses, and Student Research

Software properties define how software systems should operate. Specifying correct properties, however, can be difficult and expensive as it requires deep knowledge of the system's expected behavior and the environment in which it operates. Automated analysis techniques to infer properties from code or code executions can mitigate that cost, but are still unable to go beyond state properties and the simplest patterns of temporal properties. This limitation renders properties that sacrifice fault detection power.

To address this problem, we introduce a new type of software properties called \textit{statistical properties}, which characterize significant statistical relationships among the values of variables across …

Impact Of Secondary Treatment Types And Sludge Handling Processes On Estrogen Concentration In Wastewater Sludge, Erica J. Marti

UNLV Theses, Dissertations, Professional Papers, and Capstones

Endocrine-disrupting compounds (EDCs), such as estrogen, are known to be present in the aquatic environment at concentrations that negatively affect fish and other wildlife. Wastewater treatment plants (WWTPs) are major contributors of EDCs into the environment. EDCs are released via effluent discharge and land application of biosolids. Estrogen removal in WWTPs has been studied in the aqueous phase; however, few researchers have determined estrogen concentration in sludge. This study focuses on estrogen concentration in wastewater sludge as a result of secondary treatment types and sludge handling processes. Grab samples were collected before and after multiple treatment steps at two WWTPs …

Purification Of Fibrinogen From Human Plasma, Ayman E. Ismail

Department of Chemical and Biomolecular Engineering: Dissertations, Theses, and Student Research

A solvent detergent treated fibrinogen was purified from human plasma by cryoprecipitation (cryo) followed by chemical precipitation using ethanol (EtOH) or ammonium sulfate (AS) as precipitating agents. Amounts of fibronectin (FN), factor XIII A-subunit (FXIIIA), factor XIII b-subunit (FXIIIB), and alpha₂-antiplasmin (α₂-AP) in the isolated fibrinogen were quantified. Thromboelastography (TEG) analysis was used to evaluate the clot strength of the isolated fibrinogen and to determine the ability of the ethanol and ammonium sulfate precipitations to eliminate the solvent detergent. Sodium dodecylsulfate-polyacrylamide gel analysis indicated that fibrinogen produced by each of these precipitation methods had similar purity. …

Elasto-Capillarity In Fibrous Materials, Daria Monaenkova

All Dissertations

Current advances in the manufacture of nanoporous and nanofibrous materials with high absorption capacity open up new opportunities for the development of fiber-based probes and sensors. Pore structures of these materials can be designed to provide high suction pressure and fast wicking. During wicking, due to the strong capillary action, the liquids exert stresses on the fiber network, thus the stressed state of dry and wet parts of the material differs. In this work the effect of stress reduction in fibrous materials due to the presence of wetting liquid in the pore structure is studied in details for both static …

Design Of Advanced Fouling-Resistant And Self-Cleaning Membranes For Treatment Of Oily And Impaired Waters, Daniel Wandera

All Dissertations

The overall goal of my Doctor of Philosophy (PhD) research was to design and develop advanced anti-fouling and self-cleaning membranes for treating impaired waters. Initial work focused on the development of membranes to treat produced water, which is oily wastewater that is co-produced during oil and gas exploration. Economical, environmentally sustainable treatment of the large volumes of produced water is a grand challenge for oil and gas companies. While membranes offer many advantages over more conventional treatment methods, membrane-based treatment processes for oily waters often fail due to membrane fouling. Therefore, the primary objective of my doctoral research was to …

Engineering Single-Molecule, Nanoscale, And Microscale Bio-Functional Materials Via Click Chemistry, Michael Daniele

All Dissertations

To expand the design envelope and supplement the materials library available to biomaterials scientists, the copper(I)-catalyzed azide-alkyne cycloaddition (CuCAAC) was explored as a route to design, synthesize and characterize bio-functional small-molecules, nanoparticles, and microfibers. In each engineered system, the use of click chemistry provided facile, bio-orthogonal control for materials synthesis; moreover, the results provided a methodology and more complete, fundamental understanding of the use of click chemistry as a tool for the synergy of biotechnology, polymer and materials science. Fluorophores with well-defined photophysical characteristics (ranging from UV to NIR fluorescence) were used as building blocks for small-molecule, fluorescent biosensors. Fluorophores …

Prognostic And Health-Management Oriented Fuel Cell Modeling And On-Line Supervisory System Development, Xian Zhang

All Dissertations

Of the fuel cells being studied, the proton exchange membrane fuel cell (PEMFC) is viewed as the most promising for transportation. Yet until today, the commercialization of the PEMFC has not been widespread in spite of its large expectation. Poor long term performances or durability, and high production and maintenance costs are the main reasons. For the final commercialization of fuel cells in the transportation field, durability issues must be addressed, while costs should be further brought down. At the same time, health-monitoring and prognosis techniques are of great significance in terms of scheduling condition-based maintenance (CBM) to minimize repair …

Prediction Of The Wear & Evolution Of Cutting Tools In A Carbide / Ti-6al-4v Machining Tribosystem By Volumetric Tool Wear Characterization & Modeling, Mathew Kuttolamadom

All Dissertations

The objective of this research work is to create a comprehensive microstructural wear mechanism-based predictive model of tool wear in the tungsten carbide / Ti-6Al-4V machining tribosystem, and to develop a new topology characterization method for worn cutting tools in order to validate the model predictions. This is accomplished by blending first principle wear mechanism models using a weighting scheme derived from scanning electron microscopy (SEM) imaging and energy dispersive x-ray spectroscopy (EDS) analysis of tools worn under different operational conditions. In addition, the topology of worn tools is characterized through scanning by white light interferometry (WLI), and then application …

Ambient Habitat Noise And Vibration At The Georgia Aquarium, Peter M. Scheifele, Michael T. Johnson, Laura W. Kretschmer, John G. Clark, D. Kemper, G. Potty

Electrical and Computer Engineering Faculty Research and Publications

Underwater and in-air noise evaluations were completed in performance pool systems at Georgia Aquarium under normal operating conditions and with performance sound tracks playing. Ambient sound pressure levels at in-pool locations, with corresponding vibration measures from life support system (LSS) pumps, were measured in operating configurations, from shut down to full operation. Results indicate noise levels in the low frequency ranges below 100 Hz were the highest produced by the LSS relative to species hearing thresholds. The LSS had an acoustic impact of about 10 dB at frequencies up to 700 Hz, with a 20 dB re 1 μPa impact …

Aging-Aware Routing Algorithms For Network-On-Chips, Kshitij Bhardwaj

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Network-on-chips (NoCs) are one of the most scalable mediums to interconnect different processors in a multi-processor system. The processors are connected to routers via network interfaces and the routers are connected to each other through links. A routing algorithm is implemented inside each router that decides the path that a packet must take to reach the destination processor from the source. If a path is heavily utilized, the links and routers comprising the path start to age, and therefore can become faulty with time. In order to avoid this situation, the routing logic must be able to distribute the packets …

Multi-Functional Reconfigurable Antenna Development By Multi-Objective Optimization, Xiaoyan Yuan

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Antennas are the most essential and significant elements of any wireless communication system. The most common antennas used in wireless communication systems include dipoles/monopoles, horn antennas, loop antennas, and micro-strip antennas. Each type possesses inherent advantages and disadvantages that make them satisfactory for particular applications. The properties of these antennas, however, are fixed by the initial design and cannot be changed. These fixed properties impose restrictions on the overall system performance as the antenna cannot adapt its characteristics in response to the changing propagation parameters of the wireless medium. A reconfigurable antenna, on the other hand, can dynamically change its …

Developing A Greenhouse Gas Emissions Calculation Tool For Water Utilities, Anthony Hampton Johnston

All Theses

The issue of climate change has led to an increased emphasis on sustainable practices in almost every facet of our lives. For water utilities, this has increased scrutiny on energy use. Although traditionally viewed solely in financial terms, energy use is also the primary source of greenhouse gas (GHG) emissions from water utilities. The emerging concern over GHG emissions coincides with potential federal legislation and regulation by the Environmental Protection Agency (EPA). In order for water utilities to determine their GHG emissions, guides and tools must be made readily available. Information to educate water utilities about their GHG emissions is …