Engineering Commons^™

A Proof That P≠Np, Pascal Hitzler

Computer Science and Engineering Faculty Publications

We demonstrate the separation of the complexity class NP from its subclass P.

Analysis And Visualization Of Vascular Structures, Thomas Wischgoll

Computer Science and Engineering Faculty Publications

No abstract provided.

An Evaluation Of Non-Contact Temperature Measurements For Oxyacetylene Torch Testing Of Ultra-High Temperature Ceramics, Justin Cotter

Symposium on Research and Creative Expression (SORCE)

The feasibility of using noncontact measurement devices in oxy-acetylene torch ablation testing for UHTCs has been investigated. UHTCs are candidate materials for use in hypersonic and atmospheric re-entry vehicles for their oxidation resistance and thermal capabilities and an oxy-acetylene torch rig is being used to screen materials that show promise for these applications. Non-contact temperature measurement devices have been used for similar testing, but there are some potential issues regarding their use, such as changing emissivity of the UHTCs and combustion interferences. The feasibility of using non-contact temperature measurement devices will be evaluated through the use of thermocouples and a …

Long Term, Continuous Temperature Monitoring Of A Simple Anaerobic Digester And Open Manure Storage Pond In Eastern South Dakota, J. Darrington, E. Cortus

The Journal of Undergraduate Research

A two-cell manure storage system with a cover on the first cell was constructed in the late summer of 2009 in Eastern South Dakota. The covered cell acts as a simple anaerobic digester. Continuous temperature monitoring for 8 months shows the winter effluent temperature equilibrated to around 6°C, and that the effluent temperature trend lagged the ambient temperature trend by a month. Manure composition was also analyzed and was found to be relatively steady throughout the system. Volatile solids were the only component that dropped appreciably across the treatment cell, with an observed maximum of 50% reduction.

Residual Stress Analysis Of Composite Cannon Barrel, Tyler Brockel, Ozan Ozdemir

The Journal of Undergraduate Research

The objective of this paper is to describe the process and results of a residual stress analysis done on a composite cannon barrel. A cross section of a full cannon barrel was cut off to be used in the analysis. The barrel cross section was composed of an inner steel layer that was wrapped in an outer composite layer. The residual stress analysis was done using x-ray diffraction (XRD). The XRD machine uses different types of x-ray tubes based on what material it is analyzing. For this reason, the first portion of the experiment dealt with finding the exact material …

New Accurate Fault Location Algorithm For Parallel Transmission Lines, Pramote Chaiwan

University of Kentucky Doctoral Dissertations

Electric power systems have been in existence for over a century. Electric power transmission line systems play an important role in carrying electrical power to customers everywhere. The number of transmission lines in power systems is increasing as global demand for power has increased. Parallel transmission lines are widely used in the modern transmission system for higher reliability. The parallel lines method has economic and environmental advantages over single circuit. A fault that occurs on a power transmission line will cause long outage time if the fault location is not located as quickly as possible. The faster the fault location …

Evaluating The Effectiveness Of Peak Power Tracking Technologies For Solar Arrays On Small Spacecraft, Daniel Martin Erb

University of Kentucky Master's Theses

The unique environment of CubeSat and small satellite missions allows certain accepted paradigms of the larger satellite world to be investigated in order to trade performance for simplicity, mass, and volume. Peak Power Tracking technologies for solar arrays are generally implemented in order to meet the End-of-Life power requirements for satellite missions given radiation degradation over time. The short lifetime of the generic satellite mission removes the need to compensate for this degradation. While Peak Power Tracking implementations can give increased power by taking advantage and compensating for the temperature cycles that solar cells experience, this comes at the expense …

Robotic Testing Of Proximal Tibio-Fibular Joint Kinematics For Measuring Instability Following Total Knee Arthroplasty, Wael K. Barsoum, Ho H. Lee, Trevor G. Murray, Robb Colbrunn, Alison K. Klika, S. Butler, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

Pain secondary to instability in total knee arthroplasty (TKA) has been shown to be major cause of early failure. In this study, we focused on the effect of instability in TKA on the proximal tibio-fibular joint (PTFJ). We used a robotics model to compare the biomechanics of the PTFJ in the native knee, an appropriately balanced TKA, and an unbalanced TKA. The tibia (n = 5) was mounted to a six-degree-of-freedom force/torque sensor and the femur was moved by a robotic manipulator. Motion at the PTFJ was recorded with a high-resolution digital camera system. After establishing a neutral position, …

Activated Sludge And Other Aerobic Suspended Culture Processes, Charles J. Moretti, Dipesh Das, Brian T. Kistner, Harvey Gullicks, Yung Tse Hung

Civil and Environmental Engineering Faculty Publications

© 2011 by the authors. A review of the literature published in 2008, 2009 and 2010 relating to activated sludge treatment of wastewater is presented. The review considers information on the topics of modeling and kinetics; process microbiology; nitrogen and phosphorus removal; treatment and effects of xenobiotics; oxygen transfer; and solids separation.

Biofilm Fixed Film Systems, Harvey Gullicks, Hasibul Hasan, Dipesh Das, Charles Moretti, Yung Tse Hung

Civil and Environmental Engineering Faculty Publications

© 2011 by the authors. The work reviewed here was published between 2008 and 2010 and describes research that involved aerobic and anoxic biofilm treatment of water pollutants. Biofilm denitrification systems are covered when appropriate. References catalogued here are divided on the basis of fundamental research area or reactor types. Fundamental research into biofilms is presented in two sections, Biofilm Measurement and Characterization and Growth and Modeling. The reactor types covered are: trickling filters, rotating biological contactors, fluidized bed bioreactors, submerged bed biofilm reactors, biological granular activated carbon, membrane bioreactors, and immobilized cell reactors. Innovative reactors, not easily classified, are …

Dye Waste Treatment, Siew Teng Ong, Pei Sin Keng, Weng Nam Lee, Sie Tiong Ha, Yung Tse Hung

Civil and Environmental Engineering Faculty Publications

© 2011 by the authors. Dye wastes represent one of the most problematic groups of pollutants because they can be easily identified by the human eye and are not easily biodegradable. This literature review paper highlights and provides an overview of dye waste treatments performed over the three years period from 2008-2010. Noteworthy processes for the treatment of dye waste include biological treatment, catalytic oxidation, filtration, sorption process and combination treatments.

Influence Of Stitch Density And Stitch Thread Thickness On Compression After Impact Strength Of Stitched Composites, Kwek Tze Tan, N. Watanabe, Y. Iwahori, T. Ishikawa

Mechanical Engineering Faculty Research

This study aims to investigate the influence of stitch density and stitch thread thickness on compression after impact (CAI) strength of stitched composites. Unstitched laminated composites and specimens stitched with varying stitch density and stitch thread thickness are subjected to impact damage and then compressive loading. It is shown that stitched composites have higher CAI strength than unstitched counterpart due to smaller impact-induced delamination area, where local buckling occurs during compressive failure. However, it is revealed that the effectiveness of stitching in suppressing delamination growth and inhibiting sublaminate buckling under compressive loading is intimately related to stitch density. It is …

Towards Better Utilization Of Nexrad Data In Hydrology: An Overview Of Hydro-Nexrad, Witold F. Krajewski, Anton Kruger, James A. Smith, Ramon Lawrence, Charles Gunyon, Radoslaw Goska, Bong Chul Seo, Piotr Domaszczynski, Mary Lynn Baeck, Mohan K. Ramamurthy, Jeffrey Weber, A. Allen Bradley, Stephen A. Delgreco, Matthias Steiner

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

With a very modest investment in computer hardware and the open-source local data manager (LDM) software from University Corporation for Atmospheric Research (UCAR) Unidata Program Center, a researcher can receive a variety of NEXRAD Level III rainfall products and the unprocessed Level II data in real-time from most NEXRAD radars in the USA. Alternatively, one can receive such data from the National Climatic Data Center in Ashville, NC. Still, significant obstacles remain in order to unlock the full potential of the data. One set of obstacles is related to effective management of multi-terabyte datasets. A second set of obstacles, for …

Addressing The Dual Challenges Of Meeting Demand For Minerals And Sustainable Development, R. Larry Grayson

Mining Engineering Faculty Research & Creative Works

In recent decades, excellent progress has been made globally in finding mineral resources, extracting them efficiently and effectively, dramatically reducing environmental degradation, and preventing adverse health and safety impacts on workers and stakeholders. The industry has realized tremendous advances in technology and applied science; has met changing and more stringent environmental performance criteria; has made remarkable reductions in fatality, illness, and lost-time accident rates; and has connected better than ever before with the communities in which mining, milling, and smelting are housed. A new era focused on continuous improvement in tackling key sustainable development parameters has come and is intensifying …

Efficient Cable Shovel Excavation In Surface Mines, Kwame Awuah-Offei, Samuel Frimpong

Mining Engineering Faculty Research & Creative Works

The cable shovel is widely used in surface mining. High operating and ownership costs necessitate efficient use of the cable shovel. Operator practices have long been suspected to contribute towards the inefficient use of the shovel. Crowd arm and hoist rope speeds are key measures of operator practices. the objective of this work is to find the crowd arm and hoist rope speeds for optimal shovel performance for given initial conditions and material properties. Shovel kinematics and dynamic modeling, using shovel geometry and the simultaneous constraint method, respectively, have been employed to build models of the excavation process. Dynamic models …

Toward A Technology Management Core: Defining What The Technology Manager Needs To Know, Mark Doggett, Pam Mcgee, Sophia Scott

SEAS Faculty Publications

With the increasing demands on organizations to do “more with less,” and produce acceptable market results, productivity and performance standards continually raise the expectations on competitive success. To meet these expectations, organizations should create learning opportunities that combine the application of technical management skills along with the softer skills involved in people management. Technical managers with little training or past experience with nontechnical skills often perform poorly in technical management positions (Kroecker, 2007). Because this generation lives in a highly technical environment, managers need to be proficient in dealing with knowledge workers and systems; therefore, there is a growing emphasis …

Approaches To Arc Flash Hazard Mitigation In 600 Volt Power Systems, Curtis Thomas Latzo

USF Tampa Graduate Theses and Dissertations

Federal regulations have recognized that arc flash hazards are a critical source of potential injury. As a consequence, in order to work on some electrical equipment, the energy source must be completely shut-down. However, power distribution systems in mission critical facilities such as hospitals and data centers must sometimes remain energized while being maintained. In recent years the Arc Flash Hazard Analysis has emerged as a power system tool that informs the qualified technician of the incident energy at the equipment to be maintained and recommends the proper protective equipment to wear. Due to codes, standards and historically acceptable design …

A Catholic And Marianist Engineering Education, Kevin P. Hallinan, Margaret Pinnell

Mechanical and Aerospace Engineering Faculty Publications

The School of Engineering at the University of Dayton (UD), a Catholic and Marianist University, boasts large enrollments of 1,300 undergraduate and 350 graduate students out of a total of 7,000 undergraduates and 3,000 graduate students. It also boasts a faculty very active in research, which, under the umbrella of the University of Dayton Research Institute, is funded at a level of $100 million per year.

In the past decade, the University of Dayton has sought to better articulate the impact of its Catholic and Marianist traditions, and faculty have been challenged to embody these traditions. University mission statements and …

Multi-Pose Face Recognition And Tracking System, Binu Muraleedharan Nair, Jacob Foytik, Richard Tompkins, Yakov Diskin, Theus Aspiras, Vijayan K. Asari

Electrical and Computer Engineering Faculty Publications

We propose a real time system for person detection, recognition and tracking using frontal and profile faces. The system integrates face detection, face recognition and tracking techniques. The face detection algorithm uses both frontal face and profile face detectors by extracting the 'Haar' features and uses them in a cascade of boosted classifiers. The pose is determined from the face detection algorithm which uses a combination of profile and frontal face cascades and, depending on the pose, the face is compared with a particular set of faces having the same range for classification. The detected faces are recognized by projecting …

Fluorinated Templates For Energy-Related Nanomaterials And Applications, Mohammed J. Meziani, Fushen Lu, Li Cao, Christopher E. Bunker, Elena A. Guliants, Ya-Ping Sun

Electrical and Computer Engineering Faculty Publications

Fluorinated ionomer membranes, as represented by the commercially available Nafion films, are macroscopically homogeneous and optically transparent but microscopically inhomogeneous with the presence of nanoscale hydrophilic cavities. These cavities serve as nanoscale reactors for the synthesis of nanoparticles from a variety of materials. The membranes with embedded nanoscale semiconductors, still optically transparent, have been used as sheet-photocatalysts for energy conversion applications, while those with embedded reactive metals used as nano-energetic materials for hydrogen generation and beyond. This chapter provides an overview on the templated synthesis of nanomaterials in fluorinated ionomer membranes and the various energy-related applications of this unique class …

Comparison Of Turbulence-Induced Scintillations For Multi-Wavelength Laser Beacons Over Tactical (7 Km) And Long (149 Km) Atmospheric Propagation Paths, Mikhail Vorontsov, Venkata S. Rao Gudimetla, Gary W. Carhart, Thomas Weyrauch, Svetlana Lachinova, Ernst Polnau, Joseph Rierson, Leonid A. Beresnev, Jony Jiang Liu, Jim F. Riker

Electrical and Computer Engineering Faculty Publications

We report results of the experimental analysis of atmospheric effects on laser beam propagation over two distinctive propagation paths: a long-range (149 km) propagation path between Mauna Loa (Island of Hawaii) and Haleakala (Island of Maui) mountains, and a tactical-range (7 km) propagation path between the roof of the Dayton Veterans Administration Medical Center (VAMC) and the Intelligent Optics Laboratory (IOL/UD) located on the 5th floor of the University of Dayton College Park Center building. Both testbeds include three laser beacons operating at wavelengths 532 nm, 1064 nm, and 1550 nm and a set of identical optical receiver systems with …

God And Gadgets: Following Jesus In A Technological Age, Brad Kallenberg

Theology and Religious Studies Faculty Publications

Technologies are deeply embedded in the modern West. What would our lives be like without asphalt, glass, gasoline, electricity, window screens, or indoor plumbing? We naturally praise technology when it is useful and bemoan it when it is not. But there is much more to technology than the usefulness of this or that artifact. Unfortunately, we tend not to consider the inherently social and moral character of technology. As a result, we are prone to overlook the effects of technology on our spiritual lives. This book investigates the role technology plays in helping and hampering our Christian practice and witness.

Magnetic Resonance Image Processing Using Levy Distributed Anisotropic Diffusion, Jonathan Blackledge, Matthew Blackledge

Conference papers

We consider the physical nature of the self-diffusion of water molecules in tissue and explore how (Nuclear) Magnetic Resonance (MR) imaging may be used as a means of measuring the rate of diffusion in vivo. A discussion is presented on how these techniques may be implemented as a non-invasive means of assessing the response of tumours to novel therapeutics including some of the basic advantages and disadvantages when compared to other methods. The physical basis and mathematical models for diffusion are considered together with models for the distribution of the diffusion co-efficient including a Levy distributed model. Using a …

Understanding Risk Governance: Introducing Sociological Neoinstitutionalism And Foucauldian Governmentality For Further Theorizing, Wee-Kiat Lim

CCX Research

This article traces the career of risk across prominent theoretical approaches by highlighting their key assumptions and premises, specifically the technical approach found in the physical sciences, and economics, psychology, and sociology in the social sciences. In each discipline, the strengths and limitations of each theoretical approach are pointed out. The discussion focuses on sociology in particular because other approaches—in treating risks as dominantly technical, psychological, or economic phenomena—tend to downplay the broader historical and socio-political context that impinges on risk construction and production, and its differential impact across society. This exploration points out that institutions play an important role …

Reaction Rates Of Ozone And Terpenes Adsorbed To Model Indoor Surfaces, M. Springs, J. R. Wells, Glenn Morrison

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Reaction rates and reaction probabilities have been quantified on model indoor surfaces for the reaction of ozone with two monoterpenes (Δ3-carene and d-limonene). Molar surface loadings were obtained by performing breakthrough experiments in a plug-flow reactor (PFR) packed with beads of glass, polyvinylchloride or zirconium silicate. Reaction rates and probabilities were determined by equilibrating the PFR with both the terpene and the ozone and measuring the ozone consumption rate. to mimic typical indoor conditions, temperatures of 20, 25, and 30°C were used in both types of experiments along with a relative humidity ranging from 10% to 80%. the molar surface …

Opposing Effects Of Recirculated Gases During Cranking On Cold Start Of Diesel Engines, Rafik N. Rofail

Wayne State University Dissertations

ABSTRACT

OPPOSING EFFECTS OF RECIRCULATED GASES DURING CRANKING ON COLD START OF DIESEL ENGINES

by

RAFIK ROFAIL

August 2011

Advisor: Dr. Naeim Henein

Major: Mechanical Engineering

Degree: Doctor of Philosophy

Enhancing cold start of DI diesel engines is the motivation behind this study. A new control strategy is proposed to reduce the cranking period and the white smoke emissions. In the strategy, the gases leaving the cylinder during the cranking period are recycled back into the intake manifold using two different methods. In the first method the engine-out gases during cranking are recirculated into the intake manifold and their rate …

A Multi-Species Analysis Of Biomechanical Responses Of The Head To A Shock Wave, Richard Bolander

Wayne State University Dissertations

Shock wave induced brain injury remains a field of research that has great consequences for the rehabilitation of soldiers and civilians that are exposed to an explosion. As such, for the research to be successful in developing strategies to mitigate the effects of these injuries, appropriate research methods need to be developed. Animal models are currently employed to understand the brain's response to a shock wave exposure. Unfortunately no criteria have been established that indicates in what way the mechanical inputs that the cells in an animal's brain are subjected to are similar to a human. The purpose of this …

Supercritical Carbon Dioxide-Processed Resorbable Polymer Nanocomposites For Bone Graft Substitute Applications, Kevin Baker

Wayne State University Dissertations

Numerous clinical situations necessitate the use of bone graft materials to enhance bone formation. While autologous and allogenic materials are considered the gold standards in the setting of fracture healing and spine fusion, their disadvantages, which include donor site morbidity and finite supply have stimulated research and development of novel bone graft substitute materials. Among the most promising candidate materials are resorbable polymers, composed of lactic and/or glycolic acid. While the characteristics of these materials, such as predictable degradation kinetics and biocompatibility, make them an excellent choice for bone graft substitute applications, they lack mechanical strength when synthesized with the …

Computational Simulation Of Skull Fracture Patterns In Pediatric Subjects Using A Porcine Model, Christina Devito Wagner

Wayne State University Dissertations

In cases of suspected child abuse with skeletal trauma, it is often the role of the injury biomechanist, forensic pathologist, clinical radiologist, and forensic anthropologist to determine the mechanism of injury when the child victims cannot speak for themselves. This is a challenging task, especially for the head, as comprehensive biomechanical data on skull fracture in infants and children do not currently exist, and frequently the determination regarding cause of injury is based on anecdotal evidence from the medical literature and unsubstantiated eyewitness accounts. The current process may result in unreliable autopsy interpretation and miscarriages of justice due to a …

Creating A Graphical Front-End For A Book Or Dvd Using Photoshop, Jerome Casey

Instructional Guides

No abstract provided.