Engineering Commons^™

12 Bit Charge Redistribution Digital To Analog Converter For The Residence Time Fluxgate Magnetometer, Miguel Angel Alamillo

Open Access Theses & Dissertations

The continuous advances in CMOS VLSI technology have culminated in high speed, low voltage CMOS digital circuits with gate delays below 50 ps at 1.5 V supply. At the same time, high voltage analog signal processing has fallen behind to the high flexibility and high reliability of DSP. However, the main drawback of DSP is the need for high accuracy low distortion data converters and as a consequence of the persistent efforts of reducing size, cost and power of solid-state components the field of CMOS Mixed-Signal circuit design has become of the utmost importance.

The obvious functionality of data converters …

Probabilistic Analysis Of Concrete Fracture, Mustafa Abushaala Aldalinsi

Open Access Theses & Dissertations

It is well known to civil engineers that fatigue leads to the bulk of structural failures. In plain and reinforced concrete structures, fatigue might account for excessive deformation, excessive of crack widths, de-bonding of reinforcement and rupture of the reinforcement, all of these can lead to structural collapse. Fatigue crack propagation can be a method to predict a remaining life of a structures. Herein will show some works that have been done in order to analyze the fatigue crack growth for plain concrete specimen. The goals of this study are to estimate the critical crack length and remaining life of …

Novel Control Technique For Cadmium Sulfide Chemical Bath Deposition Using Real Time Monitoring Of Cadmium Ion Molarity, Rafael Ordonez

Open Access Theses & Dissertations

Cadmium sulfide Chemical-Bath-Deposition parameters are modified to allow, for the first time, real time monitoring of cadmium ion molarity using a commercially available cadmium ion Ion-Selective-Electreode at 60°C. This modification involves alterations to typical deposition parameters that eliminate the formation of cadmium hydroxide and keep cadmium ion molarity above 10-7M. The new or atypical parameters developed are pH values below 8.9 and lower moralities for all chemicals. In order to have complexation of cadmium ion driven mainly by ammonia, parameters that minimized complexation by other chemicals are found. Cadmium acetate concentration below 2mM and ammonium acetate concentration below 10mM minimize …

Three Dimensional Collagen Gels As A Cell Culture Matrix For The Study Of Live Cells By Raman Spectroscopy, Franck Bonnier, Aidan Meade, S. Merzha, Peter Knief, Kunal Bhattacharya, Fiona Lyng, Hugh Byrne

Articles

Three dimensional collagen gels are evaluated as matrices for the study of live cells by Raman spectroscopy. The study is conducted on a human lung adenocarcinoma (A549) and a spontaneously immortalized human epithelial keratinocyte (HaCaT) cell line. It is demonstrated, using the Alamar Blue assay, that both cell models exhibit enhanced viability in collagen matrices compared to quartz substrates, commonly used for Raman spectroscopy. Using principal component analysis, it is shown that the Raman spectral analysis of cells in collagen matrices are minimally contaminated by substrate contributions and the cell to cell spectral variations are greatly reduced compared to those …

Design Of Organic Tandem Solar Cells Using Pcpdtbt: Pc61 Bm And P3ht: Pc71bm, Gon Namkoong, Patrick Boland, Keejoo Lee, James Dean

Electrical & Computer Engineering Faculty Publications

We conducted optical and electrical simulations with the goal of determining the optimal design for conjugated polymer-fullerene tandem solar cells using poly[2,6-(4,4-bis-(2-ethylhexyl)- 4H-cyclopenta[2,1- b;3,4- b′] dithiophene)-alt-4,7-(2,1,3-benzothiadiazole)] (PCPDTBT): [6,6]-phenyl C₆₁ butyric acid methyl ester (PC₆₁ BM) as a bottom cell and poly(3-hexylthiophene) (P3HT): [6,6]-phenyl C₇₁ butyric acid methyl ester (PC₇₁BM) as a top cell. The effects of photon density, absorption, balanced and unbalanced charge carrier transport, and bimolecular recombination in the two subcells were incorporated into the simulations. We found that the maximum energy conversion efficiency (η) is 9% when charge carrier mobilities in …

Noise Propagation Through Open Windows Of Finite Depth Into An Enclosure, Caleb Sieck, Siu-Kit Lau

Durham School of Architectural Engineering and Construction: Faculty Publications

Predicting the insertion loss of an opening backed with an enclosed space is important for building noise control. Recent research in sound transmission through apertures of finite depth in infinite rigid baffles has included the effects of propagating and evanescent modes within the aperture in order to extend models to higher frequencies. The present study extends the model to the case of the aperture backed by a cavity as opposed to sound radiating into half-space. The role of coupling between the aperture modes, radiation modes, and cavity modes in the transmission was investigated. The results were compared to those of …

Utilizing Multimedia Case Studies To Teach The Professional Side Of Project Management, Cassandra C. Elrod, Susan L. Murray, Barry B. Flachsbart, Karl E. Burgher, Drew M. Foth

Business and Information Technology Faculty Research & Creative Works

This research was conducted to evaluate the effectiveness of using a LITEE multimedia case study to teaching concepts in engineering courses. The LITEE Superstar case study was implemented in an engineering Project Management course. Numerous surveys regarding student expectations, outcomes, and attitudes were collected and results are presented herein. Overall, the study provided evidence that the students felt that the LITEE case study added value to the course via the different methods of teaching material, aided in the understanding of the project selection process, and ultimately helped them be successful in their course project which was conducted for a real …

Excitation-Induced Germanium Quantum Dot Formation On Si (100)-(2×1), Ali Oguz Er, Hani E. Elsayed-Ali

Physics Faculty Publications

The effect of nanosecond pulsed laser excitation on the self-assembly of Ge quantum dots grown by pulsed laser deposition on Si (100)-(2×1) was studied. In situ reflection high-energy electron diffraction and ex situ atomic force microscopy were used to probe the quantum dot structure and morphology. At room temperature, applying the excitation laser decreased the surface roughness of the grown Ge film. With surface electronic excitation, crystalline Ge quantum dots were formed at 250 °C, a temperature too low for their formation without excitation. At a substrate temperature of 390 °C, electronic excitation during growth was found to improve the …

An Improved Methodology For Filling Missing Values In Spatiotemporal Climate Data Set, Antti Sorjamaa, Amaury Lendasse, Yves Cornet, Eric Deleersnijder

Engineering Management and Systems Engineering Faculty Research & Creative Works

In This Paper, an Improved Methodology for the Determination of Missing Values in a Spatiotemporal Database is Presented. This Methodology Performs Denoising Projection in Order to Accurately Fill the Missing Values in the Database. the Improved Methodology is Called Empirical Orthogonal Functions (EOF) Pruning, and It is based on an Original Linear Projection Method Called Empirical Orthogonal Functions (EOF). the Experiments Demonstrate the Performance of the Improved Methodology and Present a Comparison with the Original EOF and with a Widely Used Optimal Interpolation Method Called Objective Analysis. © Springer Science + Business Media B.v. 2009.

A Continuous Regression Function For The Delaunay Calibration Method, Francesco Corona, Elia Liitiäinen, Amaury Lendasse, Roberto Baratti, Lorenzo Sassu

Engineering Management and Systems Engineering Faculty Research & Creative Works

The Delaunay Tessellation and Topological Regression is a Local Simplex Method for Multivariate Calibration. the Method, developed within Computational Geometry, Has Potential for Applications in Online Analytical Chemistry and Process Monitoring. This Study Proposes a Novel Approach to Perform Prediction and Extrapolation using Delaunay Calibration Method. the Main Property of the Proposed Extension is the Continuity of the Estimated Regression Function Also Outside the Calibration Domain. to Support the Presentation, an Application in Estimating the Aromatic Composition in Light Cycle Oil by Near Infrared Spectroscopy is Discussed. © 2009 Ifac.

Influence Of Fraction Of High Angle Boundaries On The Mechanical Behavior Of An Ultrafine Grained Al-Mg Alloy, R. Kapoor, N. Kumar, R. S. Mishra, C. S. Huskamp, K. K. Sankaran

Materials Science and Engineering Faculty Research & Creative Works

The mechanical behavior of ultrafine grained AA5052 processed through different techniques-rolled, annealed, friction stir processed (FSP) and equal channel angular pressed (ECAP)-were compared and correlated with microstructure. the microstructure was characterized using electron back scattered diffraction to obtain the boundary spacing, the fraction of high angle boundaries and to estimate the dislocation density from local misorientations. Both FSP and ECAP conditions had ultrafine boundary spacing, but the fraction of high angle boundaries was larger for the FSP condition. Tensile deformation carried out at 297K, and 10-3s-1 showed a lower work-hardening rate and recovery rate for FSP as compared to the …

Friction Stir Processing Of Commercial Grade Marine Alloys To Enable Superplastic Forming, Christopher B. Smith, Arun Mohan, Rajiv S. Mishra, Murray Mahoney, Mike Miles, Scott M. Gillis, Lee M. Cerveny, Gerald Opichka

Materials Science and Engineering Faculty Research & Creative Works

The use of friction stir processing (FSP) on marine grade aluminum sheet has been investigated with the objective of locally enhancing the material properties. This can potentially allow low-cost commercial grade aluminum to be used in superplastic forming applications or further enhance the formability to allow more complex geometries to be formed. FSP has been demonstrated to enable super plasticity (uniform elongations >250%) in 5083-H116 over a range of friction stir processing conditions. © (2010) Trans Tech Publications.

An Analysis Of Strength And Ductility Of Ultrafine Grained Al Alloys, R. Kapoor, P. S. De, R. S. Mishra

Materials Science and Engineering Faculty Research & Creative Works

This paper brings together and compares data of various ultrafine grained (UFG) Al alloys processed through different routes. in general, the trend of decreasing ductility with increasing strength was observed for the UFG alloys. as compared to the coarse grained (CG) alloys, the UFG alloys show a lower ductility, a lower extent of work-hardening and a lower uniform elongation. Unlike the CG alloys, which show a large fraction of uniform to total elongation, in UFG alloys this fraction varies with processing technique. It is shown here that aging of some UFG Al alloys improves ductility. Further, it is shown that …

Impedance Spectroscopy Of Batio₃ Cubes Suspended In Lossy Liquids As A Physical Model Of Two-Phase System, Piotr Z. Jasinski, Vladimir Petrovsky, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

Impedance spectroscopy techniques were used for analysis of the physical model in a two-phase system toward determining of dielectric constant of dielectric particles suspended in liquids at various solids loading (volume fraction) levels. Model experimental studies were conducted using BaTiO3 as a dielectric material that was prepared as small cubes of uniform size (2×2×1 mm). Barium titanate (BT) cubes having a dielectric constant of 3850 were immersed in liquids of low dielectric constant and moderate electrical conductivity. Measured impedance spectra consisted of two semicircles, which were fitted for (R∥C)(R∥C) equivalent circuit. The parameters obtained from fitting were compared with the …

Constrained Optimal Orbit Design For Earth Observation, Sharon D. Vtipil

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of this dissertation is to demonstrate use requirements for a satellite observation mission can be used to determine a constrained optimal orbit based on observation site requirements, observation condition restraints, and sensor characteristics. The typical Earth observation satellite is first designed according to an appropriate orbit; then the observation requirements are used to develop a target schedule. The new design process outlines the development of the appropriate orbit by incorporating user requirements at the forefront of mission planning, not after an orbit has been selected. This research shows how to map the user requirements into constraints for the …

Effect Of Phosphorus On Cleavage Fracture In Κ-Carbide, N. I. Medvedeva, Ryan A. Howell, David C. Van Aken, Julia E. Medvedeva

Materials Science and Engineering Faculty Research & Creative Works

To understand the origin of cleavage fracture which dominates in Fe(Mn)-Al-C alloys at a high phosphorus concentration, we performed first-principles study of the phosphorus effect on ideal cleavage energy and critical stress in κ-carbide, Fe₃ AlC, a precipitate in the austenitic alloys. We find that phosphorus has higher solubility in Fe₃ AlC than in γ-Fe and sharply reduces the cleavage characteristics of κ-carbide. We show that strong anisotropy of the Fe-P bonds in Fe₃ (Al,P) C under tensile stress, leads to the appearance of large structural voids and may facilitate crack nucleation.

Active Control Of Shocks And Sonic Boom Ground Signal, Bedri Yagiz

Mechanical & Aerospace Engineering Theses & Dissertations

The manipulation of a flow field to obtain a desired change is a much heightened subject. Active flow control has been the subject of the major research areas in fluid mechanics for the past two decades. It offers new solutions for mitigation of shock strength, sonic boom alleviation, drag minimization, reducing blade-vortex interaction noise in helicopters, stall control and the performance maximization of existing designs to meet the increasing requirements of the aircraft industries. Despite the wide variety of the potential applications of active flow control, the majority of studies have been performed at subsonic speeds. The active flow control …

Optimization Models And Algorithms For Spatial Scheduling, Christopher J. Garcia

Engineering Management & Systems Engineering Theses & Dissertations

Spatial scheduling problems involve scheduling a set of activities or jobs that each require a certain amount of physical space in order to be carried out. In these problems space is a limited resource, and the job locations, orientations, and start times must be simultaneously determined. As a result, spatial scheduling problems are a particularly difficult class of scheduling problems. These problems are commonly encountered in diverse industries including shipbuilding, aircraft assembly, and supply chain management. Despite its importance, there is a relatively scarce amount of research in the area of spatial scheduling.

In this dissertation, spatial scheduling problems are …

Influence Of Interactions Between Turbulence And Radiation On Transmissivities In Hypersonic Turbulent Boundary Layers, A. M. Feldick, L. (Lian) Duan, M. F. Modest, M. P. Martín, D. A. Levin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In the current paper, a high-fidelity large eddy simulation solver is coupled to our modified line-by-line radiative transport equation solver to study the effects of absorption turbulence-radiation interations in a hypersonic turbulent boundary layer, representative of the Orion CEV entering Earth's atmosphere, at peak heating condition. The turbulent and radiation fields represent extreme conditions typical of Orion, as the simulated boundary layer represents the region of high turbulence coupled to region of highest incident radiation. A simplification in the calculation of molecular spectra with a single temperature property database in allows for tractable calculation of spectral properties. A comparison of …

Direct Numerical Simulation Of Hypersonic Turbulent Boundary Layers. Part 2. Effect Of Wall Temperature, L. (Lian) Duan, I. Beekman, M. P. Martín

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In this paper, we perform direct numerical simulation (DNS) of turbulent boundary layers at Mach 5 with the ratio of wall-to-edge temperature T w/T ℘ from 1.0 to 5.4 (Cases M5T1 to M5T5). The influence of wall cooling on Morkovin's scaling, Walz's equation, the standard and modified strong Reynolds analogies, turbulent kinetic energy budgets, compressibility effects and near-wall coherent structures is assessed. We find that many of the scaling relations used to express adiabatic compressible boundary-layer statistics in terms of incompressible boundary layers also hold for non-adiabatic cases. Compressibility effects are enhanced by wall cooling but remain insignificant, and the …

A Higher-Order Spectro-Temporal Integration Model For Predicting Signal Audibility, Qing Yang, John G. Harris

Electrical and Computer Engineering Faculty Research & Creative Works

A higher-order model to determine audibility of audio signals is presented. Previous models have been energy based (second order) and adequate only for stationary, narrow-band signals. Music, speech and other audio signals are nonstationary and wideband so traditional energy models poorly predict the audibility of these sounds. The predictions from the higher-order model are compared to actual subjective listening tests to show that the higher order, wide-band technique outperforms previous models. ©2010 IEEE.

The Research Of New Approaches To Coupling Windage Problem Based On Pressure Experiments And Analysis, Tao Jiang

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 9-18

Collapse Analysis Of Tubes Under Quasi-Static Axial Loading, Anurag Dixit, Raghawendra P S Sisodia, Nitin K. Waghmare

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 57-65

Heat Transfer From Flat Surfaces To Moving Sand, Matthew Golob, Sheldon Jeter, Dennis Sadowski

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 203-207

The Elasto-Plastic Mechanical Properties Of A Twill Dutch Woven Wire Mesh, Steven M. Kraft, Ali P. Gordon, Frank Marinacci

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 181-188

Asme Early Career Technical Journal (End Matter), Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 234-236

Design And Characterization Of An Integrate-And-Fire Neural Recording System, Sheng Feng Yen, John G. Harris

Electrical and Computer Engineering Faculty Research & Creative Works

A neuronal recording system for brain-machine interfaces (BMI) based on asynchronous biphasic pulse coding is described. A recording experiment comparing, in parallel, a commercial recording system (Tucker-Davis Technology) and the UF's custom solution (FWIRE) is set up to compare performance. The novel aspect of the UF system is that the analog signal is represented by an asynchronous pulse train, which provides a low-power, low-bandwidth, noise-resistant means for coding and transmission. Based on different front-end hardware settings, recording bandwidth and corresponding reconstruction accuracy can be varied. Taking advantage of neural firing features, the pulse-based approach requires less than 3K pulses/second to …

Use Of Web-Based Lessons Of Statistical Concepts With Graphics And Animation To Enhance The Effectiveness Of Learning, Lavanya Pillala

Browse all Theses and Dissertations

Statistics is of critical importance to engineers. However, many engineering students struggle to grasp the meaning of statistical concepts and the idiosyncrasies of statistical methodologies. Because of this problem, instructors of statistics are constantly searching for better ways to help students understand statistical concepts. The goal of this project is to design and develop web-based lessons that use graphics and animations to enhance the effectiveness of students' learning of statistical concepts.

Lessons of three important statistical concepts have been developed for this thesis - normal distribution, central limit theorem and confidence & tolerance intervals - following well-recognized instructional design development …

Relative Stability Of The Inner-Current Loop Of Peak Current-Mode Controlled Pwm Dc-Dc Converters In Ccm, Nisha Kondrath

Browse all Theses and Dissertations

Current-mode control is a commonly adopted method of regulation for pulse-width modulated (PWM) dc-dc power converters in industry, but is not well understood. The advantages of current-mode control over the voltage-mode control include inherent overload and short circuit protection, faster response, line-noise rejection, and multiple converter paralleling. Current-mode controlled system consists of (1) an inner-current loop and (2) an outer-voltage loop, which sets the reference voltage to the inner loop. To ensure stable operation of the multi-loop converter, all the sequential loops in the circuit should be stable with sufficient degree of stability. The research in this dissertation is focused …

Understanding User-Generated Content On Social Media, Bala Meenakshi Nagarajan

Browse all Theses and Dissertations

Over the last few years, there has been a growing public and enterprise fascination with 'social media' and its role in modern society. At the heart of this fascination is the ability for users to participate, collaborate, consume, create and share content via a variety of platforms such as blogs, micro-blogs, email, instant messaging services, social network services, collaborative wikis, social bookmarking sites, and multimedia sharing sites.

This dissertation is devoted to understanding informal user-generated textual content on social media platforms and using the results of the analysis to build Social Intelligence Applications.

The body of research presented in this …