Engineering Commons^™

A Biomechanical Comparison Of Locking Compression Plate Constructs With Plugs/Screws In Osteoporotic Bone Model, Krishna P. Desai

Browse all Theses and Dissertations

Locking compression plates are proven to be safe for use in open reduction and internal fixation (ORIF) especially in osteoporotic bones. Because of various combinations of holes, the system provides more options for clinicians to use either locking screws or non-locking screws. This clinical research introduces screw like plugs which can be used along with the screws in case of locking compression plates. Experimental work was performed to determine the effectiveness of the plugs. The results showed that there is not a significant difference between the groups which used plugs and did not use the plugs, both in case of …

Electrostatic Quadrupole Plasma Mass Spectrometer Measurements During Thin Film Depositions Using Simultaneous Matrix Assisted Pulsed Laser Evaporation And Magnetron Sputtering, Chad N. Hunter, Michael H. Check, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

A hybrid plasma deposition process, combining matrix assisted pulsed laser evaporation (MAPLE) of carbon nanopearls (CNPs) with magnetron sputtering of gold was investigated for growth of composite films, where 100 nm sized CNPs were encapsulated into a gold matrix. Composition and morphology of such composite films was characterized with x-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy (TEM) analysis. Carbondeposits on a gold magnetron sputter target and carbon impurities in the gold matrices of depositedfilms were observed while codepositing from gold and frozen toluene-CNP MAPLE targets in pure argon. Electrostatic quadrupole plasma analysis was used to determine that …

Development Of Wide Band Gap Semiconductor Materials For Renewable Energy, S.M. Sarif Masud

Open Access Theses & Dissertations

Several new wide band gap semiconductor nanocomposite photocatalytic materials have been synthesized from HTiNbO5 and HNb3O8 for solar energy conversion. As a source of renewable energy, the materials are being tested to produce hydrogen fuel from water via photolysis. The materials have high surface areas, are macroporous, and have flatband potentials suitable for reducing water to create hydrogen. Under visible or ultra violet light, the materials were found to be very promising as hydrogen evolving photocatalysts. As part of the synthesis of the composites, the catalysts also exhibited excellent catalytic activity under UV light for reducing ionic platinum and gold …

Combustion Characteristics Of Alh3 Flame, Sudipa Sarker

Open Access Theses & Dissertations

The combustion characteristics of Al hydride and Al were compared using a combustion chamber. Burning rate, ignition energy and temperature at atmospheric temperature and pressure in carbon dioxide and O2 were tested with a volumetric flow rate that ranged from 10 to 50% in Ar. A spark ignition system was used to ignite the Alane and Aluminum. The combustion rate was measured using a high speed camera. Results showed the combustion rate of Alane and Aluminum decreases with increasing volumetric flow rate of oxidizer. And the combustion rate of Alane is higher than that of Aluminum. Alane needs more ignition …

Scaffold Based In-Vitro Osteodistraction For Bone Tissue Engineering, Cesar Adrian Terrazas

Open Access Theses & Dissertations

Engineering of hard tissues such as bone is a challenge because of the limited ability of the body to heal large defects. Current treatment options, such as employing bone sections from the patient or a deceased donor have been utilized for some time now with various degrees of success. However, these methods still exhibit many limitations such as limited supply and the possibility of transmission of disease.

To address the many limitations of bone grafts, synthetic engineered substitutes have been developed and widely researched for nearly three decades. Generally termed scaffolds, these are matrices that serve the purpose of temporary …

Categorization Of Functional Impairments In Human Locomotion Using The Methods Of The Fusion Of Multiple Sensors And Computational Intelligence, Huiying Yu

Open Access Theses & Dissertations

The main aim of this dissertation work was to develop an intelligent system to monitor, quantify and differentiate variances in human gait with high reliability and efficiency using the fusion of multiple sensor data and the methods of fuzzy inferential logic.

Gait disorders are heterogeneous and produce disabilities that vary substantially from individual to individual. The recognition, quantification and analysis of gait dysfunction is complex and, requires the integration of large amounts of data across multiple domains (kinetic, kinematic and electromyographic). Current systems for gait analysis generally require space and complex imaging equipment, as well as prolonged processing time, rendering …

Intelligent Irrigation Zone Splitter, David Boeck

Electrical Engineering

The intelligent irrigation zone splitter allows easy expansion of an existing irrigation controller. To expand on an existing controller a new wire is needed to run between the controller and the valve. This path may be buried beneath driveways, patios, and sidewalks. The intelligent irrigation zone splitter uses an already existing wire path to control two valves and create a new watering zone. This controller uses timing and memory to split the total watering time of the zone.

Development Of A Framework To Evaluate Human Risk Towards Sustainable Risk Management, Ra'ed M. Jaradat, Rani A. Kady, C. Ariel Pinto

Engineering Management & Systems Engineering Faculty Publications

Risk managers are constantly faced with the challenge of making decisions at various levels of their organizations. One of the challenges, which often times is unavoidable, lies in assigning a monetary value to human risks. Such challenge necessitates engineering managers to make educated decisions on the level of risk that the organizations and businesses should accept when it comes to human. The purpose of this study is to suggest a suitable framework that captures this aspect of engineering Risk Management in order to make rational and sustainable decisions about such assessed risk. This will be accomplished by exploring the tools, …

Development Of An Optical Fiber-Based Corrosion Detection Sensor Based On Laser Light Reflection, Manjunatha Shenoy

Mechanical and Aerospace Engineering Theses - Archive

Corrosion plays a detrimental effect on the structural integrity of many engineering structures. It can compromise the safe operation of these structures by forming corrosion pits that deteriorates the structural surfaces and causes stress concentrations. Therefore, it is critical that corrosions are detected before structural integrity is compromised and repair becomes economically prohibitive. However, corrosions usually occur at intricate places that are hard to inspect visually. Manual inspection of the structures for corrosions requires dismantling the structures, which incurs high maintenance costs and could potentially cause damage to the components. One approach to reduce this cost is to detect and …

An Integration Of A Modern Flight Control System Design Technique Into A Conceptual Design Stability And Controls Tool, Aeromech, Amen Omoragbon

Mechanical and Aerospace Engineering Theses - Archive

The aircraft conceptual design (CD) phase is the most abstract, thus challenging phase of the entire aircraft design process. It is the responsibility of the CD engineer to identify and then to explore various aircraft concepts with the goal of arriving at the most promising concept for further evaluation. During this early design phase, the discipline stability and control tends to be underrepresented due to the lack of non-linear aerodynamic and inertia data. The methodology and software AeroMech is a vehicle configuration independent aircraft conceptual design stability and control tool, developed to help the conceptual designer to address stability and …

Plasmon Enhanced Near-Field Interactions In Surface Coupled Nanoparticle Arrays For Integrated Nanophotonic Devices, Amitabh Ghoshal

Electronic Theses and Dissertations

The current thrust towards developing silicon compatible integrated nanophotonic devices is driven by need to overcome critical challenges in electronic circuit technology related to information bandwidth and thermal management. Surface plasmon nanophotonics represents a hybrid technology at the interface of optics and electronics that could address several of the existing challenges. Surface plasmons are electronic charge density waves that can occur at a metal-dielectric interface at optical and infrared frequencies. Numerous plasmon based integrated optical devices such as waveguides, splitters, resonators and multimode interference devices have been developed, however no standard integrated device for coupling light into nanoscale optical circuits …

New Laser Technologies Analysis Of Quantum Dot And Lithographic Laser Diodes, Abdullah Demir

Electronic Theses and Dissertations

The first part of this dissertation presents a comprehensive study of quantum dot (QD) lasers threshold characteristics. The threshold temperature dependence of a QD laser diode is studied in different limits of p-doping, hole level spacing and inhomogeneous broadening. Theoretical analysis shows that the threshold current of a QD laser in the limit of uniform QDs is not temperature independent and actually more temperature sensitive than the quantum well laser. The results also explain the experimental trends of negative characteristic temperature observed in QD lasers and clarify how the carrier distribution mechanisms inside and among the QDs affect the threshold …

Reconfigurable Architecture For H.264/Avc Variable Block Size Motion Estimation Based On Motion Activity And Adaptive Search Range, Sumedha Kodipyaka

Electronic Theses and Dissertations

Motion Estimation (ME) technique plays a key role in the video coding systems to achieve high compression ratios by removing temporal redundancies among video frames. Especially in the newest H.264/AVC video coding standard, ME engine demands large amount of computational capabilities due to its support for wide range of different block sizes for a given macroblock in order to increase accuracy in finding best matching block in the previous frames. We propose scalable architecture for H.264/AVC Variable Block Size (VBS) Motion Estimation with adaptive computing capability to support various search ranges, input video resolutions, and frame rates. Hardware architecture of …

Application Of Antenna Synthesis And Digital Signal Processing Techniques For Active Millimeter-Wave Imaging Systems, Wilson Ariel Caba

Electronic Theses and Dissertations

Millimeter-wave imaging has gathered attention in recent years for its ability to penetrate clothing, thin layers of soils, and certain construction materials. However, image quality remains a challenge that needs to be addressed. One way of improving image quality is by increasing the dimensions of the collecting aperture. A sparse array can be used to synthesize a larger aperture with a limited set of relatively small detectors. In this research we design, build, and test a test-bed having an active source at 94 GHz and an array of coherent detectors, mounted on arms that extend radially on a rotary table. …

Modeling And Design Of A Photonic Crystal Chip Hosting A Quantum Network Made Of Single Spins In Quantum Dots That Interact Via Single Photons, Hubert P. Seigneur

Electronic Theses and Dissertations

In this dissertation, the prospect of a quantum technology based on a photonic crystal chip hosting a quantum network made of quantum dot spins interacting via single photons is investigated. The mathematical procedure to deal with the Liouville-Von Neumann equation, which describes the time-evolution of the density matrix, was derived for an arbitrary system, giving general equations. Using this theoretical groundwork, a numerical model was then developed to study the spatiotemporal dynamics of entanglement between various qubits produced in a controlled way over the entire quantum network. As a result, an efficient quantum interface was engineered allowing for storage qubits …

Environmental Degradation Of Oxidation Resistant And Thermal Barrier Coatings For Fuel-Flexible Gas Turbine Applications, Prabhakar Mohan

Electronic Theses and Dissertations

The development of thermal barrier coatings (TBCs) has been undoubtedly the most critical advancement in materials technology for modern gas turbine engines. TBCs are widely used in gas turbine engines for both power-generation and propulsion applications. Metallic oxidation-resistant coatings (ORCs) are also widely employed as a stand-alone protective coating or bond coat for TBCs in many high-temperature applications. Among the widely studied durability issues in these high-temperature protective coatings, one critical challenge that received greater attention in recent years is their resistance to high-temperature degradation due to corrosive deposits arising from fuel impurities and CMAS (calcium-magnesium-alumino-silicate) sand deposits from air …

Simulation For Commercial Driver License Third Party Tester Testing, Henry Truong

Electronic Theses and Dissertations

The advance of technology is thought to help ease the myriad tasks that are usually involved in operating equipment. Training and testing in modern times have been replacing with simulation technologies that mimic the actual live operations and testing. Many successful stories of flight simulation come from military fighter aircraft and commercial pilot programs. The possibilities of safety in saving lives, economic incentive in reducing the operational cost and reducing the carbon footprint via simulation makes simulation worth looking into. These considerations quickly boosted the transfer from live training operations to virtual and simulation, as were easily adopted in the …

Laser Plasma Radiation Studies For Droplet Sources In The Extreme Ultraviolet, Reuvani Kamtaprasad

Electronic Theses and Dissertations

The advancement of laboratory based Extreme Ultraviolet (EUV) radiation has escalated with the desire to use EUV as a source for semiconductor device printing. Laser plasmas based on a mass-limited target concept, developed within the Laser Plasma Laboratory demonstrate a much needed versatility for satisfying rigorous source requirements. This concept produces minimal debris concerns and allows for the attainment of high repetition rates as well as the accommodation of various laser and target configurations. This work demonstrates the generation of EUV radiation by creating laser plasmas from mass-limited targets with indium, tin, and antimony doped droplets. Spectral emission from the …

Transfer And Development Length Of Strands In Post-Tensioned Members After Anchor Head Failure, Elie El Zghayar

Electronic Theses and Dissertations

Post-tensioning tendons in segmental bridge construction are often only anchored within the deviator and pier segments. The effectiveness of the post-tensioning (PT) system is therefore dependent on proper functioning of the anchorages. On August 28, 2000 a routine inspection of the Mid-Bay Bridge (Okaloosa County, Florida) revealed corrosion in numerous PT tendons. Moreover, one of the 19-strand tendons was completely slacked, with later inspection revealing a corrosion-induced failure at the pier anchor location. Anchorage failure caused all PT force to transfer to the steel duct located within the pier segment that in turn slipped and caused the tendon to go …

Optimal Control Of Affine Nonlinear Continuous-Time Systems Using An Online Hamilton-Jacobi-Isaacs Formulation, T. Dierks, Sarangapani Jagannathan

Electrical and Computer Engineering Faculty Research & Creative Works

Solving the Hamilton-Jacobi-Isaacs (HJI) equation, commonly used in ℋ∞ optimal control, is often referred to as a two-player differential game where one player tries to minimize the cost function while the other tries to maximize it. in this paper, the HJI equation is formulated online and forward-in-time using a novel single online approximator (SOLA)-Based scheme to achieve optimal regulation and tracking control of affine nonlinear continuous-time systems. the SOLA-Based adaptive approach is designed to learn the infinite horizon HJI equation, the corresponding optimal control input, and the worst-case disturbance. a novel parameter tuning algorithm is derived which not only achieves …

Hardware Implementation Of Triply Selective Rayleigh Fading Channel Simulators, Fei Ren, Yahong Rosa Zheng

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, we implement a real-time hardware triply selective Rayleigh fading simulator. This simulator incorporates the inter-tap and spatial correlation matrices into multiple uncorrelated frequency-flat Rayleigh fading waveforms (including temporal correlation) to simulate a multiple-input multiple-output (MIMO) triply selective Rayleigh fading channel. in the correlation incorporation procedure, this simulator uses a Kronecker product method to save a large amount of hardware memories. Occupying 34% hardware resources of one Stratix III FPGA chip, this simulator can simulate 4 x 4 MIMO fading channels with 10 correlated delay-taps per subchannel in real-time for a symbol rate of 3.69 μs. Accuracy of …

Decentralized Nearly Optimal Control Of A Class Of Interconnected Nonlinear Discrete-Time Systems By Using Online Hamilton-Bellman-Jacobi Formulation, S. Mehraeen, Sarangapani Jagannathan

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, the direct neural dynamic programming technique is utilized to solve the Hamilton Jacobi-Bellman (HJB) equation online and forward-in-time for the decentralized nearly optimal control of nonlinear interconnected discrete-time systems in affine form with unknown internal subsystem and interconnection dynamics. Only the state vector of the local subsystem is considered measurable. the decentralized optimal controller design for each subsystem consists of an action neural network (NN) that is aimed to provide a nearly optimal control signal, and a critic NN which approximates the cost function. the NN weights are tuned online for both the NNs. It is shown …

Output Feedback Control Of A Quadrotor Uav Using Neural Networks, Travis Dierks, Sarangapani Jagannathan

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, a new nonlinear controller for a quadrotor unmanned aerial vehicle (UAV) is proposed using neural networks (NNs) and output feedback. the assumption on the availability of UAV dynamics is not always practical, especially in an outdoor environment. Therefore, in this work, an NN is introduced to learn the complete dynamics of the UAV online, including uncertain nonlinear terms like aerodynamic friction and blade flapping. Although a quadrotor UAV is underactuated, a novel NN virtual control input scheme is proposed which allows all six degrees of freedom (DOF) of the UAV to be controlled using only four control …

Optimal Control Of Affine Nonlinear Continuous-Time Systems, T. Dierks, Sarangapani Jagannathan

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, the optimal regulation and tracking control of affine nonlinear continuous-time systems with known dynamics is undertaken using a novel single online approximator (SOL)-Based scheme. the SOLA-Based adaptive approach is designed to learn the infinite horizon continuous time Hamilton-Jacobi-Bellman (HJB) equation and its corresponding optimal control input. a novel parameter tuning algorithm is derived which not only ensures the optimal cost (HJB) function and control input are achieved, but also ensures the system states remain bounded during the online learning process. Lyapunov techniques show that all signals are uniformly ultimately bounded (UUB) and the approximated control signal approaches …

Crack Detectability And Durability Of Coaxial Cable Sensors In Reinforced Concrete Bridge Applications, Genda Chen, Ryan D. Mcdaniel, Michael A. Brower, David Pommerenke

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The working mechanism and the measurement principle of topology-based crack sensors made of coaxial cables are briefly reviewed. The sensitivity, spatial resolution, and ruggedness of two coaxial cable sensors, respectively made of rubber and Teflon dielectric materials, were compared and validated with laboratory testing of a 4/5-scale, T-shaped, reinforced concrete beam-column specimen. Two Teflon sensors were installed on one of the solid decks of a three-span continuous highway bridge to investigate their durability and measurement repeatability. Laboratory tests indicated that both types of sensors have high sensitivity, but the Teflon sensor has a higher spatial resolution and a negligible spillover …

An Adaptive Control Strategy For Dstatcom Applications In An Electric Ship Power System, Pinaki Mitra, Ganesh K. Venayagamoorthy

Electrical and Computer Engineering Faculty Research & Creative Works

Distribution static compensator (DSTATCOM) is a shunt compensation device that is generally used to solve power quality problems in distribution systems. In an all-electric ship power system, power quality issues arise due to high-energy demand loads such as pulse loads. This paper presents the application of a DSTATCOM to improve the power quality in a ship power system during and after pulse loads. The control strategy of the DSTATCOM plays an important role in maintaining the voltage at the point of common coupling. A novel adaptive control strategy for the DSTATCOM based on artificial immune system (AIS) is presented in …

Novel Dynamic Representation And Control Of Power Systems With Facts Devices, Shahab Mehraeen, Jagannathan Sarangapani, Mariesa Crow

Electrical and Computer Engineering Faculty Research & Creative Works

FACTS devices have been shown to be useful in damping power system oscillations. However, in large power systems, the FACTS control design is complex due to the combination of differential and algebraic equations required to model the power system. In this paper, a new method to generate a nonlinear dynamic representation of the power network is introduced to enable more sophisticated control design. Once the new representation is obtained, a back stepping methodology for the UPFC is utilized to mitigate the generator oscillations. Finally, the neural network approximation property is utilized to relax the need for knowledge of the power …

Dynamic System Eigenvalue Extraction Using A Linear Echo State Network For Small-Signal Stability Analysis - A Novel Application, Jiaqi Liang, Jing Dai, Ganesh K. Venayagamoorthy, Ronald G. Harley

Electrical and Computer Engineering Faculty Research & Creative Works

A large nonlinear dynamic system usually has complex dynamic modes corresponding to the system's eigenvalues. These eigenvalues govern the system's local behavior and thus are critical information for designing system operation and control strategies. Without the availability of the system's analytical model, which is often the case for large nonlinear systems, the system's eigenvalues need to be estimated. a linear echo state network (ESN) based method for extracting observable eigenvalues of a dynamic system together with the participation factors of these eigenvalues in the accessible system states is presented in this paper. a linear ESN is first trained to track …

On The Power Allocation For Relay Networks With Finite-Alphabet Constraints, Weiliang Zeng, Mingxi Wang, Chengshan Xiao, Jianhua Lu

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, we investigate the optimal power allocation scheme for relay networks with finite-alphabet constraints. It has been shown that the previous work utilizing various design criteria with the Gaussian inputs assumption may lead to significant loss for a practical system with finite constellation set constraint, especially when signal-to-noise ratio (SNR) is in medium-to-high regions, or when the channel coding rate is medium to high. an optimal power allocation scheme is proposed to maximize the mutual information for the relay networks under discrete-constellation input constraint. Numerical examples show that significant gain can be obtained compared to the conventional counterpart …

Indiana Pavement Preservation Program, Ghim Ping (Raymond) Ong, Tommy E. Nantung, Kumares C. Sinha

JTRP Technical Reports

State highway agencies are facing immense pressure to maintain roads at acceptable levels amidst the challenging financial and economic situations. In recent years, pavement preservation has been sought as a potential alternative for managing the pavement assets, believing that it would provide a cost-effective solution in maintaining infrastructural conditions and meeting user expectations. This study explores the potential of pavement preservation concepts in managing the agency‘s pavement assets by attempting to integrate pavement preservation considerations within the network-level pavement management system. Several elements are studied in the report: (i) determining triggers for pavement preservation treatments for use in a PMS, …