Engineering Commons^™

Plasticity And Damage In Bimodal Grain Size Al-5083: Microstructural Finite Element, Steven Nelson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Bimodal and nanocrystalline aluminum alloys are being investigated as stronger replacements for conventional polycrystalline aluminum alloys. Higher strengths are achieved by reducing the grain size of a metal; however, as the grain size is reduced the ductility diminishes. One solution that limits this decrease in ductility is the addition of a few microcrystalline grains into a nanocrystalline alloy, creating a bimodal microstructure that offers a better balance of strength and ductility. Two- and three-dimensional microstructural finite element (FE) simulations of monotonic and fatigue failures in Al-5083 having bimodal grain structures are conducted. To reduce the computational time and facilitate the …

Transportation Network Resiliency: A Fuzzy Systems Approach, Nayel Urena Serulle

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Every day the dependence on transportation grows as local, regional, national, and international independence increases. Resilient transportation systems are needed to secure the highest possible level of service during disruptive events, including natural and man-made disasters. Because of limited resources, decision makers need guidance on how, when, and where to invest to improve resiliency of their networks. The research objective is to develop a method to assess and quantify resiliency, at pre-event conditions, using a fuzzy inference approach. This research expands previous work, refining key variable definitions, adjusting model interactions, and increasing transparency between metrics. This thesis presents the method …

Spatial Light Dilution As A Technique For Conversion Of Solar Energy To Algal Biomass, Daniel J. Dye

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A photobioreactor has been designed and developed to efficiently utilize solar irradiance through spatial dilution of sunlight. The concept of spatial light dilution is simple: incident sunlight is spread over a large surface area, thus reducing the photon flux density of the light. The implementation of this technique, however, is difficult. The reactor described within uses a new approach to spatial light dilution, utilizing recently-developed optical components to diffuse concentrated sunlight inside an algae culture. Preliminary productivity tests indicate a 2-3 fold increase in productivity per unit aperture (sunlight collection area) over a control reactor with direct-sunlight. Aperture productivity of …

Estimating And Verifying Household Potential To Conserve Water, Francisco J. Suero

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This thesis identifies impacts of behaviors and technology on residential indoor water use and conservation efforts. We use pre-existing detailed end-use data collected before and after toilets, faucets, showerheads, and clothes washers were retrofitted in 96 owner-occupied, single-family households in Oakland, California; Seattle, Washington; and Tampa, Florida between 2000 and 2003.

Water volume, duration of use, and time of use were recorded and disaggregated by appliance for two weeks before and four weeks after appliances were retrofitted. For each appliance, we compare observed differences in water use before and after retrofits to water savings predicted by analytical engineering, semi-analytical engineering, …

Integration Of Ultrasonic Consolidation And Direct-Write To Fabricate An Embedded Electrical System Within A Metallic Enclosure, Ludwing A. Hernandez

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A research project was undertaken to integrate Ultrasonic Consolitation (UC) and Direct-Write (DW) technologies into a single apparatus to fabricate embedded electrical systems within an ultrasonically consolidated metallic enclosure. Process and design guidelines were developed after performing fundamental research on the operational capabilities of the implemented system. In order to develop such guidelines, numerous tests were performed on both UC and DW. The results from those tests, as well as the design and process guidelines for the fabrication of an embedded touch switch, can be used as a base for future research and experimentation on the UC-DW apparatus. The successful …

Fabrication Of Multi-Material Structures Using Ultrasonic Consolidation And Laser-Engineered Net Shaping, John Olorunshola Obielodan

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This research explores the use of two additive manufacturing processes for the fabrication of multi-material structures. Ultrasonic consolidation (UC) and laser- engineered net shaping (LENS) processes were used for parallel systematic investigations of the process parameters and methodologies for the development of multi-material structures.

The UC process uses ultrasonic energy at low temperature to bond metallic foils. A wide range of metallic materials including nickel; titanium; copper; molybdenum; tantalum; MetPreg®; silver; stainless steel; and aluminum alloys 1100, 3003, and 6061 were bonded in different combinations. Material domains are inherently discrete in ultrasonically consolidated structures. The mechanical properties of some of …

Analysis Of Field Programmable Gate Array-Based Kalman Filter Architectures, Arvind Sudarsanam

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A Field Programmable Gate Array (FPGA)-based Polymorphic Faddeev Systolic Array (PolyFSA) architecture is proposed to accelerate an Extended Kalman Filter (EKF) algorithm. A system architecture comprising a software processor as the host processor, a hardware controller, a cache-based memory sub-system, and the proposed PolyFSA as co-processor, is presented. PolyFSA-based system architecture is implemented on a Xilinx Virtex 4 family of FPGAs. Results indicate significant speed-ups for the proposed architecture when compared against a space-based software processor. This dissertation proposes a comprehensive architecture analysis that is comprised of (i) error analysis, (ii) performance analysis, and (iii) area analysis. Results are presented …

Design Of An Adaptable Run-Time Reconfigurable Software-Defined Radio Processing Architecture, Joshua R. Templin

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Processing power is a key technical challenge holding back the development of a high-performance software defined radio (SDR). Traditionally, SDR has utilized digital signal processors (DSPs), but increasingly complex algorithms, higher data rates, and multi-tasking needs have exceed the processing capabilities of modern DSPs. Reconfigurable computers, such as field-programmable gate arrays (FPGAs), are popular alternatives because of their performance gains over software for streaming data applications like SDR. However, FPGAs have not yet realized the ideal SDR because architectures have not fully utilized their partial reconfiguration (PR) capabilities to bring needed flexibility. A reconfigurable processor architecture is proposed that utilizes …

Architecture, Modeling, And Analysis Of A Plasma Impedance Probe, Magathi Jayaram

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Variations in ionospheric plasma density can cause large amplitude and phase changes in the radio waves passing through this region. Ionospheric weather can have detrimental effects on several communication systems, including radars, navigation systems such as the Global Positioning Sytem (GPS), and high-frequency communications. As a result, creating models of the ionospheric density is of paramount interest to scientists working in the field of satellite communication.

Numerous empirical and theoretical models have been developed to study the upper atmosphere climatology and weather. Multiple measurements of plasma density over a region are of marked importance while creating these models. The lack …

Complexity And Power Consumption In Stochastic Iterative Decoders, Keyur M. Payak

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Stochastic iterative decoding is a novel method to decode the bits received at the end of a communication channel and to control the rate of error happening in the message bits due to noise being injected into the channel. This decoder uses stochastic computation that is based on manipulation of probabilities from a random sequence of digital bits. Hardware needed for implementing this arithmetic is very simple and can be completely implemented using simple digital complementary metal oxide gates. This helps the decoder to be technology independent, which is a major advantage over its digital and analog counterparts, which are …

Toward The Validation Of Depth-Averaged, Steady-State Simulations Of Fluvial Flows Using Three-Dimensional, Steady-State, Rans Turbulence Models, Pedro Abdiel Mateo Villanueva

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Calculations of fluvial flows are strongly influenced by geometry complexity and large overall uncertainty on every single measurable property, such as velocity and shear. Moreover, a considerable portion of the data obtained from computational simulations arose from two-dimensional, steady-state models. The present work states a different approach to perform computer-based simulations and analyze fluvial flows. For the first part, the suitability of OpenFOAM to be used as the main CFD solver to analyze fluvial flows is studied. Initially, two well documented channel configurations are computationally studied using OpenFOAM. Finally, these results are compared to the output obtained from one of …

Destructive Testing And Finite-Element Modeling Of Full-Scale Bridge Sections Containing Precast Deck Panels, Travis R. Brackus

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Full-depth, precast panel deck systems are becoming more common in bridge installation and repair. The objective of these systems is to achieve the performance of cast-in-place systems while simultaneously saving time and money. The structural behavior of these systems has been the subject of scrutiny in recent research. The Utah Department of Transportation demolished a steel I-girder bridge containing a precast panel deck system and provided two full-scale specimens for this project. Destructive testing was performed at Utah State University on the specimens to investigate three failure modes: flexural, beam shear, and punching shear. Finite-element models were created using ANSYS …

Minimizing Base Column Demands In Multi-Story Buckling Restrained Braced Frames Using Genetic Algorithms, Christopher Hiroshi Yeates

Theses and Dissertations

Most structural optimization procedures focus on minimizing the total volume of steel in an attempt to reduce overall costs. However, many other factors can have an effect on the overall cost of a structure. Base column demands in particular, can affect base plate sizes, anchorage, and foundation design. Researchers have found that present methods for estimating column demands are too conservative. Nonlinear time history analyzes were conducted on buckling-restrained braced frames of six heights. Optimized results were found considering three ductility constraints and two optimization objectives. The two optimization objectives were minimized total brace area and minimized base column demands. …

Aortic Coarctation: Recent Developments In Experimental And Computational Methods To Assess Treatments For This Simple Condition, John F. Ladisa, Charles A. Taylor, Jeffrey A. Feinstein

Biomedical Engineering Faculty Research and Publications

Coarctation of the aorta (CoA) is often considered a relatively simple disease, but long-term outcomes suggest otherwise as life expectancies are decades less than in the average population and substantial morbidity often exists. What follows is an expanded version of collective work conducted by the authors' and numerous collaborators that was presented at the 1st International Conference on Computational Simulation in Congenital Heart Disease pertaining to recent advances for CoA. The work begins by focusing on what is known about blood flow, pressure and indices of wall shear stress (WSS) in patients with normal vascular anatomy from both clinical imaging …

Parameterizable Network-On-Chip Emulation Framework, Jaya Suseela

UNLV Theses, Dissertations, Professional Papers, and Capstones

Networks-on-Chip (NoCs) have been proposed as a promising solution to complex on-chip communication problems. But there is no public accessible HDL synthesizable NoC framework which connects industrial level cores and runs real applications on them. Moreover, many challenging research problems remain unsolved at all levels of design abstraction; design exploration of NoC architecture for applications, scheduling and mapping algorithms, evaluation of switching, topology or routing algorithm for efficient execution of application and optimizing communication cost, area, energy etc Solution to solve the above problem calls for the development of synthesizable, parameterizable NoC Framework that would evaluate and implement the above …

Energy Efficient Led Displays, John Mani Kumar Jupalli

UNLV Theses, Dissertations, Professional Papers, and Capstones

In this research work, an innovative pixel architecture RGBW, consisting of red (R), green (G), blue (B), and white (W) LEDs, is designed and implemented for color generation. Energy consumption of new pixel architecture consisting of RGBW LEDs is compared to standard architecture consisting of RGB LEDs. Human perception experiments are conducted to study the differences in perception between the two architectures when the same colors are generated using RGBW vs. RGB. Measurements of power for a 32inch x 16inch LED display has proved up to 18% power savings for low saturated colors, up to 8% for high saturated colors …

The Development And Validation Of A Finite Element Model Of A Canine Rib For Use With A Bone Remodeling Algorithm., Scott J. Sylliaasen

Master's Theses

Studies are currently being performed to determine the effects of bisphosphonate treatments on the structure and density of bone tissue. One of the pathways for gaining a better understanding of the effects of this and other treatments involves creating a computer simulation. Theory suggests that bone tissue structure and density are directly related to the manner in which the tissue is loaded. Remodeling is the process in which bone tissue is resorbed in areas of low stress distributions, and generated in areas of high stress distributions. Previous studies have utilized numerical methods and finite element methods to predict bone structure …

Control Of Longitudinal Pitch Rate As Aircraft Center Of Gravity Changes, John Andres Cadwell Jr.

Master's Theses

In order for an aircraft to remain in stable flight, the center of gravity (CG) of an aircraft must be located in front of the center of lift (CL). As the center of gravity moves rearward, pitch stability decreases and the sensitivity to control input increases. This increase in sensitivity is known as pitch gain variance. Minimizing the pitch gain variance results in an aircraft with consistent handling characteristics across a broad range of center of gravity locations.

This thesis focuses on the development and testing of an open loop computer simulation model and a closed loop control system to …

Static And Fatigue Failure Response Of Woven Carbon Fiber Specimens With Double Edge Notches, Ahmad J. Amini

Master's Theses

Carbon fiber composites are continually seeing increased use in aerospace applications. It is necessary to understand their failure modes in order to properly design and perform analysis on structures constructed primarily from them. This thesis studies woven carbon fiber composites with and without double-edge notches in a series of static and fatigue tests performed on an Instron 8801 servo-hydraulic testing system.

Specimens were constructed of Advanced Composites Group product # LTM45EL woven carbon fiber pre-preg/epoxy and were cut to approximately 9-inch in length and 1-inch in width. Notches were cut into some of the specimens using a slitting saw blade …

Effects Of Cloud-Induced Photovoltaic Power Transients On Power System Protection, Joel A. Nelson

Master's Theses

As the world strives towards finding alternative sources of power generation, photovoltaic generation has become an increasingly prevalent alternative energy source on power systems world-wide. This paper studies the effects that incorporating photovoltaic generation has on the existing power systems and their power system protection schemes. Along with the addition of this emerging alternative energy source comes the volatility of PV power generation as cloud-cover produces erratic variations in solar irradiance and PV power production. Such variations in PV power may lead to unfavorable operating conditions and power system failures. The issues addressed in this paper include a study of …

Artificial Skin Tactile Sensor For Prosthetic And Robotic Applications, Ross James Miller

Master's Theses

To solve the problem of limited tactile sensing in humanoid robotics as well as provide for future planned mechanical prostheses, an innovative tactile sensor system was created and embedded into two realistic-looking artificial skin gloves. These artificial skin tactile sensors used small piezoelectric ceramic disks to measure applied force at multiple points on each glove. The gloves were created using silicone rubber to simulate both the texture and look of human skin, while maintaining both flexibility and durability. The sensor outputs were buffered by high-impedance voltage-following operational amplifiers, and then read sequentially using a multiplexing scheme by a microcontroller. Sensor …

The Effectiveness Of Damage Arrestment Devices In Delaying Fastener-Hole Interaction Failures In Carbon Fiber Polyurethane Foam Composite Sandwich Panels Subjected To Static And Dynamic Loading Under Increased Temperatures, Dominic E. Surano

Master's Theses

A study was conducted to investigate simple, cost-effective manufacturing techniques to delay skin-core delamination, micro-buckling and bearing stress failures resulting from fastener-hole interactions. Composite sandwich panels, with and without damage arrestment devices (DADs), were subjected to monotonic compression at a rate of 5mm per second, and compression-compression fatigue at 50% yield at an amplitude of 65%, under temperatures of 75, 100, 125, 150, 175, and 200 °F.

The sandwiches tested were composed of two-layer cross-weave carbon fiber facesheets, a polyurethane foam core, and an epoxy film adhesive to join the two materials. The most successful method to delay the aforementioned …

Assessment Of Morphology And Hemodynamics In Normal And Remodeled Microvasculature With Parameter Sensitivity Analysis, Shilpi Ghosh

Master's Theses

The goal of this study was to compare the morphological and hemodynamic characteristics of normal and remodeled vascular networks in the mouse gracilis muscle. To this end, previously developed models to assess flows and vascular branching were used to assess the normal and remodeled microcirculatory networks. The analysis revealed that the average individual vessel flow rates for vessels of similar caliber and total volumetric flow rates in the networks do not change for vessels of the same caliber after remodeling. Connectivity changes and average diameters primarily change in the larger arterioles after remodeling. A few correlations could be made between …

Anaerobic Co-Digestion Of Wastewater Treatment Pond Algae With Wastewater Sludge, Daniel Eric Heimel

Master's Theses

Microalgae harvested from wastewater treatment ponds can be anaerobically digested to produce biogas, a renewable fuel resource. However, past experiments have shown some limitations of algae digestion. Algal cell walls are thought to be resistant to digestion, and the high protein content of algae can lead to ammonia toxicity in digesters. Co-digestion of algae with substrates containing higher C:N ratios (e.g., waste paper) can be used to maintain non-inhibitory ammonia concentrations and increase methane production. However, high carbon waste co-substrates have become costly or are not readily available in many communities. Although domestic wastewater sludge has only a marginally higher …

Development Of Cubesat Vibration Testing Capabilities For The Naval Postgraduate School And Cal Poly San Luis Obispo, Marissa Brummitt

Master's Theses

The Naval Postgraduate School is currently developing their first CubeSat, the Solar Cell Array Tester CubeSat, or NPS-SCAT. Launching a CubeSat, such as NPS-SCAT, requires environmental testing to ensure not only the success of the mission, but also the safety of other CubeSats housed in the same deployer. This thesis will address the development of CubeSat vibration testing methodology at NPS, including subsystem testing, engineering unit qualification, and flight unit testing. In addition, the new Cal Poly CubeSat Test POD Mk III will be introduced and evaluated based upon comparison with the Poly Picosatellite Orbital Deployer (P-POD). Using examples from …

Correction To Mitochondrial Free [Ca2+] Increases During Atp/Adp Antiport And Adp Phosphorylation: Exploration Of Mechanisms, Johan Haumann, Ranjan K. Dash, David F. Stowe, Age D. Boelens, Daniel A. Beard, Amadou K.S. Camara

Biomedical Engineering Faculty Research and Publications

No abstract provided.

Pickling Behavior Of Aisi 304 Stainless Steel In Sulfuric And Hydrochloric Acid Solutions, W Homjabok, S Permpoon, G Lothongkum

Journal of Metals, Materials and Minerals

Oxide scales as well as a Cr-depleted layer, which grows between the oxide scale and base metal, are formed on AISI 304 stainless steel surface during high temperature processing. Pickling is an important process which includes mechanical and chemical operations to remove oxide scales, Cr-depleted layers, and to recover the surface passivity. The multi-step pickling is commonly used because of its higher efficiency than a single step pickling. In this study, the multi-step pickling of AISI 304 stainless steel in HCl solution was investigated instead of H2SO4 solution for the first step of pickling. HF+HNO3 mixed acid is traditionally used …

Development Of An Aluminum Semi-Solid Extrusion Process, T Rattanochaikul, S Janudom, N Memongkol, J Wannasin

Journal of Metals, Materials and Minerals

Semi-solid extrusion process is a new forming process that is quite promising because the process requires lower forming pressure than conventional solid extrusion. In addition, semi-solid extrusion does not require large machines, which results in lower production costs. The aim of this article is to study the feasibility of an aluminum semi-solid extrusion process. The semi-solid technique selected for usage in this study was the Gas Induced Semi-Solid (GISS) process. The laboratory extrusion system was developed in this work. In the experiments, nitrogen gas was injected into aluminum melt for about 5 seconds. After that, the obtained semi-solid slurry was …

Oxidation Of Cyclohexane And Ethylbenzene By Hydrogen Peroxide Over Co-Substituted Heteropolytungstate Catalyst, W Kanjina, W Trakarnpruk

Journal of Metals, Materials and Minerals

The tetrabutylammonium salt of Co-substituted heteropolytungstate, [(n-C4H9)4N]4 HPW11Co(H2O)O39.3H2O was synthesized and characterized. It was shown to be an active catalyst for the oxidation of cyclohexane and ethylbenzene. The oxidation reactions were performed using green oxidant hydrogen peroxide and acetonitrile as solvent. The major products of the oxidation of cyclohexane were cyclohexanone (K) and cyclohexanol (A). High selectivity towards K-A oil was achieved. At longer time cyclohexanol was converted to cyclohexanone. Ethylbenzene was also selectively oxidized to acetophenone. These oxidation reactions appear to be radical processes since they were totally inhibited in the presence of radical scavenger.

Versatile Route For Preparation Of Polydiacetylene/Zno Nanocomposites And Their Colorimetric Response To Ph And Ethanol, N Rungruangviriya, N Traiphol

Journal of Metals, Materials and Minerals

This contribution presents a simple method to prepare polydiacetylene(PDA)/ZnO nanocomposites, which can be utilized as active materials in sensing technology. The ZnO nanoparticles, which constitute of Zn-OH2 + , Zn-OH and Zn-O- groups at their surfaces, function as nano-substrates for self-assembling of diacetylene monomers, 10,12-pentacosadiynoic acid (PCDA), in aqueous medium. Photopolymerization of the assemblies yields poly(PCDA)/ZnO nanocomposites with core-shell structure. Strong interactions between the active groups at ZnO surface and carboxylic head groups of poly(PCDA) promote chain ordering and reduce segmental dynamics of poly(PCDA) in the nanocomposites. The existence of strong interfacial interaction drastically affects the colorimetric response behavior of …