Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

2007

Discipline
Institution
Keyword
Publication
Publication Type
File Type

Articles 3511 - 3540 of 3831

Full-Text Articles in Engineering

Composite Data From Centrifugal Experimentation Regarding Human Information Processing, Ronald K. Butcher Jan 2007

Composite Data From Centrifugal Experimentation Regarding Human Information Processing, Ronald K. Butcher

Browse all Theses and Dissertations

A cognitive model illustrating decrement in human performance as a function of increased G-forces has been highly sought after by the Department of Defense (DoD) for various reasons. The F-16 and other air combat platforms are super-agile aircraft that are easily capable of imposing G-forces on a pilot that are beyond human physiological limitations. Knowledge of these physiological limits and more importantly the resultant restrictions in cognitive function could prove invaluable to those who design and pilot such aircraft. The model may be utilized in the construction of improved flight simulators that incorporate more realistically performing enemy targets and therefore …

Go to article

Biochemical Characterization Of Htrf1 And Htep1, Two Proteins Involved In Telomere Maintenance, Kambiz Tahmaseb Jan 2007

Biochemical Characterization Of Htrf1 And Htep1, Two Proteins Involved In Telomere Maintenance, Kambiz Tahmaseb

Browse all Theses and Dissertations

Telomeres are the structures that protect the ends of linear chromosomes from fusion and degradation. The telomere consists of tandem repeated DNA sequences that can range from hundreds of bases to kilo-bases depending on the organism. As the cells of an organism replicate their DNA, these repeats are lost due to the end replication problem, where the ends of linear DNA cannot be fully replicated. As the telomeres are shortened through each round of replication, they eventually reach a critical point. Once the telomeres are too short and the cell risks losing coding sequences, a signaling pathway is initiated that …

Go to article

Investigation Of Cylindrically-Conformed Four-Arm Spiral Antennas, Douglas J. Glass Jan 2007

Investigation Of Cylindrically-Conformed Four-Arm Spiral Antennas, Douglas J. Glass

Browse all Theses and Dissertations

A four-arm spiral antenna offers broadband frequency response, wide beamwidths, reduced size compared to other antenna designs, and the ability to determine the relative direction of an incident signal with appropriate mode-forming. The reduced overall area projection of the four-arm spiral antenna compared to other antenna designs and the ability to be manufactured in a planar format allows the antenna to reside within an Unmanned Air Vehicle (UAV) fuselage. This thesis investigates the effects of cylindrically-conforming two different designs of a four-arm spiral antenna to reside within the fuselage of a medium-sized UAV. Theoretical predictions of antenna performance were created …

Go to article

Improved Thresholding Technique For The Monobit Receiver, Jonathan Gordon Buck Jan 2007

Improved Thresholding Technique For The Monobit Receiver, Jonathan Gordon Buck

Browse all Theses and Dissertations

Wideband digital receivers typically use a very high sampling rate to capture a signal for near real-time processing. Very robust digital techniques, like the Monobit FFT technique, have been developed to provide near real-time processing of captured timedomain signals. Most of these techniques trade accuracy for processing speed by approximating computationally complex mathematical operations. The approximation sometimes makes it difficult to detect multiple signals if the difference between their amplitudes is more than a few dB. This thesis presents a dynamic thresholding technique for multi-tone signal detection. The technique is based on setting an allowable ratio between the magnitude of …

Go to article

Parameterizable Channelized Wideband Digital Receiver For High Update Rate, Peter E. Buxa Jan 2007

Parameterizable Channelized Wideband Digital Receiver For High Update Rate, Peter E. Buxa

Browse all Theses and Dissertations

Wideband digital receivers are important components used prevalently by the United States Air Force for many modern electronic warfare systems. Currently, many digital receiver architectures are designed for a specific mission requirement and are not parameterizable, modular, or reusable for varying mission requirements. Also, many designs are technology, platform, and vendor dependent which make upgrading existing fielded systems costly and difficult. Additionally, current wideband FFT-based digital receivers must wait until a number of samples equal to the size of the FFT are collected before spectral information can be updated. Achieving a high spectral update rate is important for the accurate …

Go to article

Design And Performance Evaluation Of 1 Giga Hertz Wideband Digital Receiver, Kiranraj George Jan 2007

Design And Performance Evaluation Of 1 Giga Hertz Wideband Digital Receiver, Kiranraj George

Browse all Theses and Dissertations

The lack of a priori knowledge about the waveform of interest, the multitudes of signals the receiver might receive, and the noise energy that occupies the same portion of the frequency spectrum as the signal makes the design of a modern wideband receiver very challenging. Especially, the receiver must be able to detect a weak signal in the presence of a strong one, which requires a high two-signal instantaneous dynamic range (IDR). To fulfill this requirement, the receiver must detect genuine weak signals and avoid the detection of strong signals' sidelobes and noise and spurs generated from the receiver system. …

Go to article

Rolling Mill Optimization Using An Accurate And Rapid New Model For Mill Deflection And Strip Thickness Profile, Arif Sultan Malik Jan 2007

Rolling Mill Optimization Using An Accurate And Rapid New Model For Mill Deflection And Strip Thickness Profile, Arif Sultan Malik

Browse all Theses and Dissertations

This work presents improved technology for attaining high-quality rolled metal strip. The new technology is based on an innovative method to model both the static and dynamic characteristics of rolling mill deflection, and it applies equally to both cluster-type and non cluster-type rolling mill configurations. By effectively combining numerical Finite Element Analysis (FEA) with analytical solid mechanics, the devised approach delivers a rapid, accurate, flexible, high-fidelity model useful for optimizing many important rolling parameters. The associated static deflection model enables computation of the thickness profile and corresponding flatness of the rolled strip. Accurate methods of predicting the strip thickness profile …

Go to article

Change Detection Methods For Hyperspectral Imagery, Karmon Marie Vongsy Jan 2007

Change Detection Methods For Hyperspectral Imagery, Karmon Marie Vongsy

Browse all Theses and Dissertations

This thesis studies the detection of changes using hyperspectral images. Change Detection (CD) is the process of identifying and examining temporal and spectral changes in signals. Detection and analysis of change provide valuable information of possible transformations in a scene. Hyperspectral imaging (HSI) sensors are capable of collecting data at hundreds of narrow spectral bands. Such sensors provide high-resolution spatial and spectrally rich information that can be exploited for CD. This work develops and implements various CD algorithms for detection of changes using Hyperspectral images. The main objectives are to study and develop different HSI change detection algorithms. The explored …

Go to article

Computational Methods For The Objective Review Of Forensic Dna Testing Results, Jason R. Gilder Jan 2007

Computational Methods For The Objective Review Of Forensic Dna Testing Results, Jason R. Gilder

Browse all Theses and Dissertations

Since the advent of criminal investigations, investigators have sought a "gold standard" for the evaluation of forensic evidence. Currently, deoxyribonucleic acid (DNA) technology is the most reliable method of identification. Short Tandem Repeat (STR) DNA genotyping has the potential for impressive match statistics, but the methodology not infallible. The condition of an evidentiary sample and potential issues with the handling and testing of a sample can lead to significant issues with the interpretation of DNA testing results. Forensic DNA interpretation standards are determined by laboratory validation studies that often involve small sample sizes. This dissertation presents novel methodologies to address …

Go to article

Minute Doping Of Pulsed Laser Deposition Processed Y123 Thin Films With Tb, Ce, And Pr, Joseph William Kell Jan 2007

Minute Doping Of Pulsed Laser Deposition Processed Y123 Thin Films With Tb, Ce, And Pr, Joseph William Kell

Browse all Theses and Dissertations

Three rare earth elements (Tb, Ce, and Pr) were chosen for the investigation into whether adding minute quantities (≤1 at%) of dopants could improve the film quality of YBa2C 3O7-δ(Y123) thin films. The compositions studied are (Y1-x,Rex)Ba2Cu3O7-δ (RE=Tb, Ce, Pr; x=0.1, 0.01, 0.001). Good quality thin films were produced by PLD and showed significant improvement to properties when exposed to a magnetic field. Ce and Pr (x=0.001) doped films showed modest improvement. However, the Tb doped system showed substantial improvement to Jc(H), with a …

Go to article

Investigating The Role Of Subunit Iii In The Structure And Function Of Rhodobacter Sphaeroides Cytochrome C Oxidase, R. Ryan Geyer Jan 2007

Investigating The Role Of Subunit Iii In The Structure And Function Of Rhodobacter Sphaeroides Cytochrome C Oxidase, R. Ryan Geyer

Browse all Theses and Dissertations

The role of subunit III (SIII) in cytochrome c oxidase structure and function was investigated using enzyme isolated from the bacterium Rhodobacter sphaeroides. Energy minimization calculations suggested that in the absence of SIII, subunit I (SI) adopted a more open conformation. This observation was tested through the use of limited proteolysis using, á-chymotrypsin. The results showed that in the absence of SIII the solution structures of wild-type and I/II oxidase were not significantly different, and that proteolysis occurred exclusively at the N and C-termini of SI. Upon inactivation of I/II oxidase by catalytic turnover, and subsequent digestion with the protease …

Go to article

Summaritive Digest For Large Document Repositories With Application To E-Rulemaking, Lijun Chen Jan 2007

Summaritive Digest For Large Document Repositories With Application To E-Rulemaking, Lijun Chen

Browse all Theses and Dissertations

Large document repositories need to be organized and summarized to make them more accessible and understandable. Such needs exist in many applications, including web search, e-rulemaking (electronic rulemaking) and document archiving. Even though much has been done in the areas of document clustering and summarization, there are still many new challenges and issues that need to be addressed as the repositories become larger, more prevalent and dynamic. In this dissertation, we investigate more informative ways to organize and summarize large document repositories, especially e-rulemaking feedback repositories (ERFRs), so that the large repositories can be managed and digested more efficiently and …

Go to article

The Effect Of Configural Displays On Pilot Situation Awareness In Helmet-Mounted Displays, Joseph C. Jenkins Jan 2007

The Effect Of Configural Displays On Pilot Situation Awareness In Helmet-Mounted Displays, Joseph C. Jenkins

Browse all Theses and Dissertations

The current research utilized configural displays within the domain of aviation to assess what design features of configural displays contribute to the formation of operator situation awareness (SA). Configural displays map system information relevant to operator goals onto geometric shapes called emergent features. An emergent feature is formed from the combination of individual line segments to produce a global feature more perceptually salient and recognized sooner than the individual parts themselves. Configural displays have been shown in previous research to provide better operator performance for integration tasks where multiple pieces of information must be considered at once, yet the design …

Go to article

Development Of An Intelligent Autonomous Coffee Maker, Nicholas J. Vanderpool Jan 2007

Development Of An Intelligent Autonomous Coffee Maker, Nicholas J. Vanderpool

Browse all Theses and Dissertations

Using Intelligent Control Methodology Home coffee machines have improved over time with the addition of features such as self-activating timers and crude temperature controlled heating elements. However, home coffee brewer development has stagnated and has yet to achieve full automation status. Present coffee machines leave the user burdened with the mundane and messy task of preparing the coffee maker every time. Also, should the user decide to prepare less than an entire pot, he/she must estimate the correct amount of water and coffee to add. This can lead to a weak or strong brew, giving undesirable results. In order to …

Go to article

Fpga Based Hardware Implementation Of Advanced Encryption Standard, Sowrirajan Sampath Jan 2007

Fpga Based Hardware Implementation Of Advanced Encryption Standard, Sowrirajan Sampath

Browse all Theses and Dissertations

On October, 2, 2000, The National Institute of Standards and Technology (NIST) announced Rijndael as the new Advanced Encryption Standard (AES). The other competing algorithms were Mars, RC6, Serpent and Two-fish. The Predecessor to the AES was Data Encryption Standard (DES) which is considered to be insecure because of its vulnerability to brute force attacks. DES was a standard from 1977 and stayed until the mid 1990's. However, by the mid 1990s, it was clear that the DES's 56-bit key was no longer big enough to prevent attacks mounted on contemporary computers, which were thousands of times more powerful than …

Go to article

Design And Validation Of A High-Lift Low-Pressure Turbine Blade, Mark W. Mcquilling Jan 2007

Design And Validation Of A High-Lift Low-Pressure Turbine Blade, Mark W. Mcquilling

Browse all Theses and Dissertations

This dissertation is a design and validation study of the high-lift low-pressure turbine (LPT) blade designated L2F. High-lift LPTs offer the promise of reducing the blade count in modern gas turbine engines. Decreasing the blade count can reduce development and maintenance costs and the weight of the engine, but care must be taken in order to maintain turbine section performance with fewer blades. For an equivalent amount of work extracted, lower blade counts increase blade loading in the LPT section. The high-lift LPT presented herein allows 38% fewer blades with a Zweifel loading coefficient of 1.59 and maintains the same …

Go to article

Sic Schottky Diodes And Polyphase Buck Converters, Veda Prakash N. Galigekere Jan 2007

Sic Schottky Diodes And Polyphase Buck Converters, Veda Prakash N. Galigekere

Browse all Theses and Dissertations

The turn-on characteristics of a SiC Schottky diode are analyzed theoretically, by simulation, and by experiment. The static characteristics of SiC Schottky diodes and Si junction diodes are analyzed for normal and high temperatures. The effects of diffusion capacitance and junction capacitance on the turn-off transition of SiC Schottky diode have been analyzed theoretically. The turn-off transition of a SiC Schottky barrier diode is analyzed by modeling the metal-semiconductor junction capacitance considering the linear and the non-linear effects. Behavior of the linear and the non-linear metal-semiconductor junction capacitance models are evaluated exper- imentally. The performance of SiC Schottky diodes is …

Go to article

Skin And Proximity Effects In Two Parallel Plates, Hamdi Eltayib Abdelbagi Jan 2007

Skin And Proximity Effects In Two Parallel Plates, Hamdi Eltayib Abdelbagi

Browse all Theses and Dissertations

Time varying currents within winding and core conductors induce magnetic fields. When more than one conductor is present the resultant magnetic field can be found by adding the individual magnetic fields by superposition. The resultant magnetic field in turn induces eddy currents within each electrical component within the vicinity of the resultant magnetic field. Eddy currents flow in the opposite direction of the primary current and increase the resistance by reducing the area in which the primary current has to travel. Eddy currents also reduce the effectiveness of the conductors to conductor high frequency currents. Skin and proximity effects were …

Go to article

Phase-Locked Piv Investigation Of The Effects Of The Blowing Ratio Of A Pulsed Vortex Generator Jet In A Low-Pressure Turbine, Nathan Michael Woods Jan 2007

Phase-Locked Piv Investigation Of The Effects Of The Blowing Ratio Of A Pulsed Vortex Generator Jet In A Low-Pressure Turbine, Nathan Michael Woods

Browse all Theses and Dissertations

At very high altitudes the Reynolds number flow through the low pressure turbine section of the gas turbine engine can drop below 25,000. At these low Reynolds numbers the flow is laminar and extremely susceptible to separation which can lead to increased losses and reduced lift. Small jets of air injected through the suction surface of the airfoil, called Vortex Generator Jets (VGJs), have been shown successful in suppressing separation and maintaining attached flow. Pulsing of these jets has been shown to be as effective as steady jets while reducing the amount of mass flow needed. An experiment using Particle …

Go to article

Bezier Surface Generation Of The Patella, Dale A. Patrick Jan 2007

Bezier Surface Generation Of The Patella, Dale A. Patrick

Browse all Theses and Dissertations

A method to generate control points for a given collection of data points is developed. The shape characteristics of the patella are used as a case study. The developed computer graphic techniques are demonstrated using the given data of the 3-d patella model. Generation of curved surfaces in drafting has evolved over the years from draftsman who used tools such as French curves to today's drafting being well served by being able to apply numerical analysis on the ever increasing capabilities of computer. As an everyday observed example, nature very rarely produces two shapes that are equal to another. It …

Go to article

Fpga-Based Implementation Of A Digital Processor For An Instantaneous Frequency Measurement Receiver, James M. Helton Jan 2007

Fpga-Based Implementation Of A Digital Processor For An Instantaneous Frequency Measurement Receiver, James M. Helton

Browse all Theses and Dissertations

Digital wideband receivers are essential elements used in electronic warfare (EW) applications. Instantaneous Frequency Measurement (IFM) receivers are suitable for use in EW systems due to the ultrawide instantaneous radio-frequency (RF) bandwidth, fine-frequency resolution, and moderately high sensitivity and dynamic range. Conventional IFM receivers use analog components such as power dividers, crystal video detectors, and hybrids. This research presents the architecture and design implementation of a purely digital IFM receiver based on a patented algorithm courtesy of the United States Air Force. The invention is capable of detecting a short wave pulse with 1 MHz error for every 100 nsec. …

Go to article

Characterization And Modeling Methodology Of Polytetrafluoroethylene Based Reactive Materials For The Development Of Parametric Models, Stephen D. Rosencrantz Jan 2007

Characterization And Modeling Methodology Of Polytetrafluoroethylene Based Reactive Materials For The Development Of Parametric Models, Stephen D. Rosencrantz

Browse all Theses and Dissertations

Certain materials, when impacting a target at high velocity will chemically react due to the shock wave passing through them, thereby increasing the damage done by the material. In particular, the reactive materials of interest are capable of acting as both structure and explosive, allowing them to achieve an effect similar to a High Explosive Incindiary (HEI), without the complexity and added mass of fuses. There are a large number of materials/material combinations that could be used in reactive munitions. The purpose of this effort is to determine an efficient analytical characterization methodology that can be validated with a minimal …

Go to article

Stability And Static Noise Margin Analysis Of Static Random Access Memory, Rajasekhar Keerthi Jan 2007

Stability And Static Noise Margin Analysis Of Static Random Access Memory, Rajasekhar Keerthi

Browse all Theses and Dissertations

The transistor mismatch can be described as two closely placed identical transistors have important differences in their electrical parameters as threshold voltage, body factor and current factor and make integrated circuit design and fabrication less predictable and controllable. Stability of a static random access memory (SRAM) is defined through its ability to retain the data at low-VDD. It is seriously affected by increased variability of transistor mismatch and decreased supply voltage and therefore becomes a major limitation of overall performance of low-voltage SRAM in nanometer CMOS process. The stability limitation is addressed through the design of a seven-transistor (7T) SRAM …

Go to article

Design Of A Controller To Control Light Level In A Commercial Office, Saeid Javidbakht Jan 2007

Design Of A Controller To Control Light Level In A Commercial Office, Saeid Javidbakht

Browse all Theses and Dissertations

Proper amount of light in a business office is important for health and productivity of the employees. On a sunny day, there may be more than enough light entering the office from outside to carry out the necessary tasks. Presently, the main source of light in most offices is the fluorescent lamp. Thus, It is possible to save energy by dimming the fluorescent lamp. Dimming of the fluorescent lamp is possible by changing the frequency of the sinusoidal voltage or current. Hence, there is a need of a control system to adjust the light from the fixtures based on the …

Go to article

Functional Interplay Between Subthreshold Ion Channels In Preautonomic Neurons Of The Hypothalamic Paraventricular Nucleus In Health And Disease Conditions, Patrick M. Sonner Jan 2007

Functional Interplay Between Subthreshold Ion Channels In Preautonomic Neurons Of The Hypothalamic Paraventricular Nucleus In Health And Disease Conditions, Patrick M. Sonner

Browse all Theses and Dissertations

Under normal conditions, blood pressure is tightly regulated through autonomic tonic and reflex mechanisms. However, when the set-point for blood pressure is chronically elevated, hypertension occurs. Hypertension if untreated can lead to further complications including heart failure, stroke and kidney failure. Elevated sympathetic outflow is known to contribute to the development and/or maintenance of hypertension, and while the hypothalamic paraventricular nucleus (PVN), a preautonomic center, has been implicated in the elevation of sympathetic activity during hypertension, the precise pathophysiological mechanisms underlying sympathoexcitation remain unclear. Subthreshold ion channels, including the A-type K +(I A) and the T-type Ca 2+ …

Go to article

Non-Cooperative Modulation Recognition Via Exploitation Of Cyclic Statistics, Eric C. Like Jan 2007

Non-Cooperative Modulation Recognition Via Exploitation Of Cyclic Statistics, Eric C. Like

Browse all Theses and Dissertations

This research proposes and evaluates a feature based modulation classification system designed to discriminate between AM, BFSK, OFDM, DS-CDMA, 4-ASK, 8-ASK, BPSK, QPSK, 8-PSK, 16- PSK, 16-QAM, and 64-QAM signals without a priori knowledge of critical signal parameters, including carrier frequency, symbol rate, or phase offset, among others. The classifier is based on the principles of cyclostationarity and leverages cyclic statistics to make its classification decision. The classification process is performed in a hierarchical process in order to exploit the lower variance of lower order cyclic statistics before making use of the higher order cyclic statistics. The initial classification is …

Go to article

Fabrication And Testing Of Scaffolds For Cell Growth From Ionic Liquid Solubilized Fibroin, Maneesh Kumar Gupta Jan 2007

Fabrication And Testing Of Scaffolds For Cell Growth From Ionic Liquid Solubilized Fibroin, Maneesh Kumar Gupta

Browse all Theses and Dissertations

The advent of tissue engineering has spurred research into developing materials to act as scaffolds for tissue growth. These scaffolds require materials capable of mimicking the in vivo conditions so that tissues can be grown effectively in vitro. Silk is an attractive biomaterial for use in tissue engineering applications because of its slow degradation, excellent mechanical properties, and biocompatibility. The major objective of the research in this thesis is to demonstrate a simple method to cast films directly from silk fibroin dissolved in an ionic liquid. The films cast from the silk ionic liquid solution were found to support normal …

Go to article

High Spurious-Free Dynamic Range Digital Wideband Receiver For Multiple Signal Detection And Tracking, Vivek Sarathy Jan 2007

High Spurious-Free Dynamic Range Digital Wideband Receiver For Multiple Signal Detection And Tracking, Vivek Sarathy

Browse all Theses and Dissertations

The advent of field-programmable gate array (FPGA) has provided an excellent platform to market prototyping of full receiver-on-chip designs in a short time. The design of multi-tone wideband receiver has always been a challenge because of the difficulty to detect weak signals in the presence of noise in the frequency spectrum and also the presence of general spurs generated by the receiver. In this research, architecture for a FPGA-based 2.56-GSPS digital wideband receiver with multi-tone signal detection and tracking is designed to demonstrate the capability of replacing more expensive analog components into their cheaper digital design counterparts. Novel hardware implementations …

Go to article

Comparative Microarray Data Mining, Shihong Mao Jan 2007

Comparative Microarray Data Mining, Shihong Mao

Browse all Theses and Dissertations

As a revolutionary technology, microarrays have great potential to provide genome-wide patterns of gene expression, to make accurate medical diagnosis, and to explore genetic causes underlying diseases. It is commonly believed that suitable analysis of microarray datasets can lead to achieve the above goals. While much has been done in microarray data mining, few previous studies, if any, focused on multiple datasets at the comparative level. This dissertation aims to fill this gap by developing tools and methods for set-based comparative microarray data mining. Specifically, we mine highly differentiative gene groups (HDGGs) from given datasets/classes, evaluate the concordance of datasets …

Go to article

Particle Based Plasma Simulation For An Ion Engine Discharge Chamber, Sudhakar Mahalingam Jan 2007

Particle Based Plasma Simulation For An Ion Engine Discharge Chamber, Sudhakar Mahalingam

Browse all Theses and Dissertations

Design of the next generation of ion engines can benefit from detailed computer simulations of the plasma in the discharge chamber. In this work a complete particle based approach has been taken to model the discharge chamber plasma.This is the first time that simplifying continuum assumptions on the particle motion have not been made in a discharge chamber model. Because of the long mean free paths of the particles in the discharge chamber continuum models are questionable. The PIC-MCC model developed in this work tracks following particles: neutrals, singly charged ions, doubly charged ions, secondary electrons, and primary electrons. The …

Go to article

First Prev Next Last