Engineering Commons^™

Application Of Intermediate Wavelength Band Spectroscopic Ellipsometry To In-Stu. Real Time Fabrication Of Multiple Layer Alternating Hghalow Refractive Index Filters, Blaine D. Johs, Jeffery S. Hale, John A. Woollam, Craig M. Herzinger

Department of Electrical and Computer Engineering: Faculty Publications

Disclosed is application of oblique angle of incidence, reflection and/or transmission mode spectroscopic ellipsometry PSI and/or DELTA, (including combinations thereof and/or mathematical equivalents), vs. wavelength data over an intermediate wavelength band range around a pass or reject band, to monitor and/or control fabrication of multiple layer high/low refractive index band-pass, band-reject and varied attenuation vs. wavelength thin film interference filters, either alone or in combination with transmissive non-ellipsometric electromagnetic beam turning point vs. layer data obtained at an essentially normal angle of incidence.

Shear Modulus Degradation Of Liquefying Sand: Quantification And Modeling, Peter A. Olsen

Theses and Dissertations

A major concern for geotechnical engineers is the ability to predict how a soil will react to large ground motions produced by earthquakes. Of all the different types of soil, liquefiable soils present some of the greatest challenges. The ability to quantify the degradation of a soil's shear modulus as it undergoes liquefaction would help engineers design more reliably and economically. This thesis uses ground motions recorded by an array of downhole accelerometers on Port Island, Japan, during the 1995 Kobe Earthquake, to quantify the shear modulus of sand as it liquefies. It has been shown that the shear modulus …

Undergraduate Research: Experiences From A Three-Year Project, Peter Schuster, Charles Birdsong

Mechanical Engineering

There are significant benefits of research for the involved undergraduate student. These include exposure to advanced topics, introduction to research methods, and direct interaction with faculty and other students. Faculty and institutions benefit as well by the increased interaction with students – fresh eyes in research projects, more energized research groups, and more engaged alumni. However, there are some challenges in designing a research program to work primarily with undergraduates. These include the students’ lack of exposure to advanced topics, short tenure on the project, and potentially lower commitment to the results. There are a number of ways to address …

Designing And Manufacturing Microelectronic Packages For High-Power Light-Emitting Diodes, Brian Wright, Jianbiao Pan, Richard Savage

Industrial and Manufacturing Engineering

A new microelectronic package was designed for a high-power light-emitting diode (LED). The objective was to build a package that enables the LED to operate with currents as high as 2 Amps. An innovative thin-film interface has been developed to electrically connect the cathode of the LED die to a 22AWG Cu wire. This thin-film interface is wirebondable and solderable, and consists of three layers: Au, Ni93/V7, and Si. Four 1 mil Au wirebonds, supporting 2A of maximum current, connect the Au thin-film to the LED die cathode. Sn96Ag4 solder is used for connecting the Ni93/V7 thin-film to the 22AWG …

Nevada Risk Assessment/Management Program – Phase 2 (Nramp2): Quarterly Progress Report July 1, 2007 Through September 30, 2007, Klaus J. Stetzenbach

Nevada Risk Assessment/Management Program

Work conducted in this 4th quarter consisted of 3 major activities:

• Continue the receipt and reconciliation of Area 5 Radioactive Waste Management Site (RWMS) inventory data.

• Receive, review, install, calibrate, and run the Goldsim Area 5 Performance Assessment (PA) Model, and review the supporting parameters and assumptions in the 93-document reference set as a tool for regulatory compliance and closure assessment.

• Identify, review, and compare the interpretation of pertinent regulatory guidelines and orders by DOE sites in compliance for PA, Compliance Assessment (CA), and closure activities - as they may relate to the Nevada Test Site (NTS) …

Resilient Modulus Of Compacted Crushed Stone Aggregate Bases, Tommy C. Hopkins, Tony L. Beckham, Charlie Sun

Kentucky Transportation Center Research Report

In recent years, the American Association of State Highway Transportation Officials (AASHTO) has recommended the use of resilient modulus for characterizing highway materials for pavement design. This recommendation evolved as result of a trend in pavement design of using mechanistic models. Although much progress has been made in recent years in developing mathematical, mechanistic pavement design models, results obtained from those models are only as good as the material parameters used in the models. Resilient modulus of aggregate bases is an important parameter in the mechanistic models. The main goal of this study was to establish a simple and efficient …

A Nondestructive Technique For Determining Complex Permittivity And Permeability Of Magnetic Sheet Materials Using Two Flanged Rectangular Waveguides, Milo W. Hyde Iv, Michael J. Havrilla

Faculty Publications

In this paper, a nondestructive technique for determining the complex permittivity and permeability of magnetic sheet materials using two flanged rectangular waveguides is presented. The technique extends existing single probe methods by its ability to simultaneously measure reflection and transmission coefficients imperative for extracting both permittivity and permeability over all frequencies. Using Love’s Equivalence Principle, a system of coupled magnetic field integral equations (MFIEs) is formed. Evaluation of one of the two resulting spectral domain integrals via complex plane integration is discussed. The system, solved via the Method of Moments (MoM),yields theoretical values for the reflection and transmission coefficients. These …

Piezo-Electrochemical Transducer Effect (Pect) Intercalated Graphite Micro-Electromechanical Actuators, Glen A. Kading

Theses and Dissertations

The purpose of this research is to investigate the Piezo-Electrochemical Transducer (PECT) effect in intercalated graphite as a possible mechanism of actuation for micro-electromechanical systems (MEMS). This dissertation presents the results of research into the PECT effect in H2SO4-intercalated graphitized carbon fibers, including both electrical and mechanical characteristics of this effect. PECT fibers achieve up to 1.7% strain at 1.4 V of applied potential. In contrast, the piezoelectric material polyvinylidene difluoride (PVDF) generates only 0.01% strain and polysilicon thermal expansion between 0.02 and 0.06% strain depending on the thermal conductivity of the particular polysilicon that the actuators are fabricated in. …

Ceas E-News 11.06.2007, College Of Engineering And Applied Sciences

College of Engineering and Applied Sciences News

PCI mural dedication ceremony honors artist, enhances Parkview Campus

Transient Molecular Dynamics Simulations Of Viscosity For Simple Fluids, Richard L. Rowley, Jason C. Thomas

Faculty Publications

A transient molecular dynamics (TMD) method has been developed for simulation of fluid viscosity. In this method a sinusoidal velocity profile is instantaneously overlaid onto equilibrated molecular velocities, and the subsequent decay of that velocity profile is observed. The viscosity is obtained by matching in a least-squares sense the analytical solution of the corresponding momentum transport boundary-value problem to the simulated decay of the initial velocity profile. The method was benchmarked by comparing results obtained from the TMD method for a Lennard-Jones fluid with those previously obtained using equilibrium molecular dynamics (EMD) simulations. Two different constitutive models were used in …

Educating The Workforce Of The Future, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "Educating the Workforce of the Future" from November 5, 2007.

A Theoretical Framework For Quality-Aware Cross-Layer Optimized Wireless Multimedia Communications, Song Chi, Haohong Wang, Dalei Wu

Department of Electrical and Computer Engineering: Faculty Publications

Although cross-layer has been thought as one of themost effective and efficient ways formultimedia communications over wireless networks and a plethora of research has been done in this area, there is still lacking of a rigorous mathematical model to gain indepth understanding of cross-layer design tradeoffs, spanning from application layer to physical layer. As a result, many existing cross-layer designs enhance the performance of certain layers at the price of either introducing side effects to the overall system performance or violating the syntax and semantics of the layered network architecture. Therefore, lacking of a rigorous theoretical study makes existing cross-layer …

Effect Of Beam Splicing On Seismic Response Of Buckling-Restrained Braced Frames, Gary S. Prinz

Theses and Dissertations

The deformation capacity of typical buckling-restrained braced frames (BRBFs) is limited by the rotation capacity of connecting regions. The rotation capacity of the connection region is limited by fracture of the gusset welds and yielding in the beams and columns. A different connection detail with beam-splices outside the gusset has been shown to increase connection rotation capacity when compared to typical connections, in a few component tests. This study expands upon the performed component tests, by analyzing the beam splice connection at the system level under directional dynamic loads. Finite element analysis and dynamic loads are used to analyze two …

Rate-Distortion Optimized Vector Spiht For Wavelet Image Coding, Y. Liang, Scott E. Budge

Electrical and Computer Engineering Faculty Publications

In this paper, a novel image coding scheme using rate-distortion optimized vector quantization of wavelet coefficients is presented. A vector set partitioning algorithm is used to locate significant wavelet vectors which are classified into a number of classes based on their energies, thus reducing the complexity of the vector quantization. The set partitioning bits are reused to indicate the vector classification indices to save the bits for coding of the classification overhead. A set of codebooks with different sizes is designed for each class of vectors, and a Lagrangian optimization algorithm is employed to select an optimal codebook for each …

A Handheld Texel Camera For Acquiring Near-Instantaneous 3d Images, B.M. Boldt, Scott E. Budge, R.T. Pack, P.D. Israelsen

Electrical and Computer Engineering Faculty Publications

A Texel camera is a device which synchronously captures depth information via a ladar and digital imagery of the same scene. The ladar and digital camera are co-boresighted to eliminate parallax. This configuration fuses the ladar data to the digital image at the pixel level, eliminating complex post-processing to register the datasets. This paper describes a handheld version of a Texel Camera which can be used to create near-instantaneous 3D imagery. The hardware configuration of the Texel Camera, issues and method associated with ladar/camera calibration, and representative imagery are presented.

Trajectory Shaping Of Surface-To-Surface Missile With Terminal Impact Angle Constraint, S. Subchan

Makara Journal of Technology

This paper presents trajectory shaping of a surface-to-surface missile attacking a fixed with terminal impact angle constraint. The missile must hit the target from above, subject to the missile dynamics and path constraints. The problem is reinterpreted using optimal control theory resulting in the formulation of minimum integrated altitude. The formulation entails nonlinear, two-dimensional missile flight dynamics, boundary conditions and path constraints. The generic shape of optimal trajectory is: level flight, climbing, diving; this combination of the three flight phases is called the bunt manoeuvre. The numerical solution of optimal control problem is solved by a direct collocation method. The …

Limiting Maximum Drag Reduction Asymptote For The Moment Coefficient Of An Enclosed Rotating Disk With Fine Spiral Grooves, Budiarso Budiarso, Keizo Watanabe, Satoshi Ogata

Makara Journal of Technology

In this study, the limiting maximum drag reduction asymptote for the moment coefficient of an enclosed rotating disk with fine spiral grooves in turbulent flow region were obtained analytically. Analysis which were based on an assumption for a simple parabolic velocity distribution of turbulent pipe flow to represent relative tangential velocity, was carried out using momentum integral equations of the boundary layer. For a certain K- parameter the moment coefficient results agree well with experimental results for maximum drag reduction in an enclosed rotating disk with fine spiral grooves and drag reduction ratio approximately was 15 %. Additionally, the experimental …

Co2 Absorption From Its Mixture With Ch4 Or N2 Through Hollow Fiber Membrane Contactor Using Water As Solvent, Sutrasno Kartohardjono, Anggara Anggara, Subihi Subihi, Yuliusman Yuliusman

Makara Journal of Technology

CO2 Absorption from Its Mixture with CH4 or N2 through Hollow Fiber Membrane Contactor using Water as Solvent. Hollow fiber membrane contactors have been widely used as gas-liquid contactors recently such as in the CO2 absorption process from gas stream. This research aims to evaluate the effectiveness of hollow fiber membrane contactor to absorb CO2 from its mixture with CH4 or N2 using water through mass transfer and hydrodynamic tests. There are 3 membrane modules used in this research with shell diameter of 1.9 cm, length of 40 cm, outer fiber diameter of 2.7 mm and fiber number in the …

Reverse Link Cdma System Capacity Evaluation For Stratospheric Platform Mobile Communications, Iskandar Iskandar

Makara Journal of Technology

We propose an analysis of reverse link CDMA multispot beam stratospheric platforms (SPF) in this paper. The SPF is currently proposed as a novel wireless technology for the development of the next generation fixed and mobile communications. The geometry of this technology is different from that of the terrestrial but rather similar to the satellite based cellular system. However, evaluation on the CDMA system capacity of this technology has not been much reported. This paper addresses all possible multiple access interference analyses including the effects of channel fading and shadowing in order to evaluate the system capacity. Single SPF and …

The Potency Of Fire And Explosion Hazard On Premium Oil Storage Tank At Depot X 2007, Fatma Lestari, Warid Nurdiansyah

Makara Journal of Technology

The Potency of Fire and Explosion Hazard on Premium Oil Storage Tank at Depot X 2007. Premium oil storage tanks have fire and explosion risk because Premium oil is flammable liquid. Because of that, fire and explosion risk assessment on Premium oil storage tank at Depot X is needed as foundation to fire and explosion risk management, and comply with regulations. Method of this research is Dow’s Fire and Explosion Index. This research indicate that F&EI value for Premium oil storage tank is 118,82. Based on that F&EI value, level of risk at Premium oil storage tank is intermediate risk.

Analysis Of Three Phase Controlled Rectifier With The Same Distance Control As Compared To The Same Angle Control, Sudirman S., Sri Kurniati A.

Makara Journal of Technology

Analysis of three phase controlled rectifier with the same distance control as compared to the same angle control. This research aim to compare the firing of the same distance and the same angle control at three phase controlled rectifier with seen generated harmonic at input (AC side). Then calculate of rectifier efficiency and power factor comparison from both the control type. The rectifier use passive filter with resistance 11 ohm and is analysed with program simulation using PSPICE version 7.1. Result of research indicate that use of the same distance control generates the 5th and 7th harmonics, while the same …

The Use Of Red Cabbage’S Anthocyanine Extract As A Photosensitizer On A Dye-Sensitized Nanocrystalline Tio2 Solar Cell, Akhiruddin Maddu, Mahfuddin Zuhri, Irmansyah Irmansyah

Makara Journal of Technology

The use of Red Cabbage’s anthocyanine extract as a photosensitizer on a Dye-Sensitized Nanocrystalline TiO2 Solar Cell. A solid-state dye-sensitized nanocrystalline TiO2 solar cell utilizing anthocyanin extract form red cabbage as photosensitizer was fabricated. The solar cell was formed in sandwich structure, which two electrodes sandwiching polymer electrolyte containing a redox couple (I-/I3 -). One of the electrodes, namely working electrode, TiO2 layer on TCO (transparent conducting oxide) coated glass substrate was sensitized with anthocyanin dye as electron donor in the system. Another electrode was a carbon sheet as a counter electrode. Gel electrolyte based on PEG (polyethylene glycol) containing …

Effect Of Contact Time On Interface Reaction Between Aluminum Silicon (7% And 11%) Alloy And Steel Dies Skd 61, Bambang Suharno, Neni Octapiani Nurhayati, Bustanul Arifin, Sri Harjanto

Makara Journal of Technology

Effect of Contact Time on Interface Reaction between Aluminum Silicon (7% and 11%) Alloy and Steel Dies SKD 61. Die soldering (die sticking) is a defect of metal casting in which molten metal “welds” to the metallic die mold surface during casting process. Die soldering is the result of an interface reaction between the molten aluminum and the die material. Aluminum alloy with 7 and 11% silicon and SKD 61 die steel are the most common melt and die material used in aluminum die casting. This research is done to study the morphology and the characteristics of the formed AlxFeySiz …

Acuta Enews November 2007, Vol.36, No. 11

ACUTA Newsletters

In This Issue

From ACUTA Headquarters.................. Jeri A. Semer, CAE, ACUTA Executive Director

Tech Talk: There Are Lots of Zeroes Behind a Yottabit............ Kevin Tanzillo, Dux PR.

DC Update............... Jeanne Jansenius, Sewanee, The University of the South

lnfo Links ............... Randy Hayes, Univ. of Northern lowa

Board Report............... Riny Ledgerwood, San Diego State Univ., ACUTA Sec./Treasurer

ls Your lP Phone Counterfeit?..................... Gary Audin, Delphi

FYI: Useful lnformation from Campus.................. Eric Weil, Student Monitor

Thanks to 2007 Exhibitors

Welcome New Members

Check lt Out: RFls/RFPs, Job Postings, Press Releases

Commissioning High Performance Residences In Hot, Humid Climates, Florida Solar Energy Center, Ken Fonorow

FSEC Energy Research Center®

Since 2001, the authors have engaged several builders in the Gainesville, FL area to build over 500 high performance new energy efficient homes in multiple sub divisions. The builders keep building to increased levels of energy efficiency. Each home is individually designed, inspected, rated and commissioned for optimum performance. This paper summarizes the experiences to date with two production builders who have cost shared with the Building America program to deliver these outstanding results. Keys to success are commitment from the final decision maker; scopes of work for subcontractors with specific performance criteria; clear communication with the trades often accompanied …

Closing The Gap: Getting Full Performance From Residential Central Air Conditioners. Task 4.2-Develop New Climate-Sensitive Air Conditioner, Design, Construction, And Testing, Florida Solar Energy Center, Don B. Shirey Iii

FSEC Energy Research Center®

This study evaluated the performance of a prototype air conditioning system. The configuration of the prototype was based on detailed simulation results performed as part of this study. The results of the previously completed simulation indicated that energy-efficient, properly-ventilated homes in humid climates need equipment options or configurations that can provide a modest amount of additional dehumidification capacity while coordinating their operation with conventional cooling and ventilation systems. A prototype air conditioning system was constructed using currently available components and provides a method to independently control sensible (temperature) and latent (moisture) building loads. The prototype system was tested in both …

Computing Population Variance And Entropy Under Interval Uncertainty: Linear-Time Algorithms, Gang Xiang, Martine Ceberio, Vladik Kreinovich

Departmental Technical Reports (CS)

In statistical analysis of measurement results, it is often necessary to compute the range [V-,V+] of the population variance V=((x1-E)^2+...+(xn-E)^2)/n (where E=(x1+...+xn)/n) when we only know the intervals [Xi-Di,Xi+Di] of possible values of the xi. While V- can be computed efficiently, the problem of computing V+ is, in general, NP-hard. In our previous paper "Population Variance under Interval Uncertainty: A New Algorithm" (Reliable Computing, 2006, Vol. 12, No. 4, pp. 273-280), we showed that in a practically important case, we can use constraints techniques to compute V+ in time O(n*log(n)). In this paper, we provide new algorithms that compute V- …

In-House Development Of Scheduling Decision Support Systems: Case Study For Scheduling Semiconductor Device Test Operations, Tali Freed, K. H. Doerr, T. Chang

Industrial and Manufacturing Engineering

Most manufacturing processes can benefit from an automated scheduling system. However;: the design of a fast, computerised scheduling system that achieves high-quality results and requires minimal resources is a difficult undertaking. Efficient .. scheduling of a semiconductor device test facility requires an information system that provides good schedules quickly. Semiconductor device testing-is the last stage of the long semiconductor manufacturing process, and therefore. is subjected to customer service pressures. The cost of an off-the-shelf computerised scheduling system may he prohibitive for many companies. In addition, many companies are taken aback by other characteristics of off-the-shelf scheduling systems, such as code …

Experimental Measurement Of Overhead Associated With Active Probing Of Wireless Mesh Networks, Brian Keegan, Karol Kowalik

Conference papers

Wireless Mesh Networks (WMNs) represent the next generation wireless networks. The increased capacity of WMNs means that they are now capable of providing backhaul services traditionally maintained by wired networks. The attraction of WMNs is their ease of deployment and ability to self organise, self configure, and self heal. In order to successfully achieve this objective careful consideration must be applied when constructing a WMN. In order to optimise the operation of the network, data should traverse the network by means of the most efficient route. Characterisation and path selection will be determined by the routing algorithm coupled with the …

Spatial Distributions Of Heating, Cooling, And Industrial Degree-Days In Turkey, Ilhami Yildiz, B. Sosaoglu

BioResource and Agricultural Engineering

The degree-day method is commonly used to estimate energy consumption for heating and cooling in residential, commercial and industrial buildings, as well as in greenhouses, livestock facilities, storage facilities and warehouses. This article presents monthly and yearly averages and spatial distributions of heating, cooling, and industrial degree-days at the base temperatures of 18 °C and 20 °C, 18 °C and 24 °C, and 7 °C and 13 °C, respectively; as well as the corresponding number of days in Turkey. The findings presented here will facilitate the estimation of heating and cooling energy consumption for any residential, commercial and industrial buildings …