Engineering Commons^™

Cubic Spline Regression For The Open-Circuit Potential Curves Of A Lithium-Ion Battery, Qingzhi Guo, Ralph E. White

Faculty Publications

A cubic spline regression model was used to fit the experimental open-circuit potential (OCP) curves of two intercalation electrodes of a lithium-ion battery. All the details of an OCP curve were accurately predicted by the resulting model. The number of regression intervals used to fit an OCP curve was determined in a way such that in each regression interval the OCP exhibits a profile predictable by a third-order polynomial. The locations of the data points used to separate regression intervals were optimized. Compared to a polynomial model with the same number of fitting parameters, the cubic spline regression model is …

A Mathematical Model For A Lithium-Ion Battery/Electrochemical Capacitor Hybrid System, Godfrey Sikha, Ralph E. White, Branko N. Popov

Faculty Publications

A one-dimensional model for predicting the performance of a battery/electrochemical capacitor-hybrid system has been developed. Simulation results are presented for a LiCoO₂|LiPF₆ ethylene carbonate/dimethyl carbonate|carbon battery system and a Maxwell PC 10F carbon double-layer electrochemical capacitor. The current shared between the battery and the electrochemical capacitor at very short times depends on the ohmic resistances of the battery and the capacitor. As the discharge proceeds, the operating conditions such as frequency, duty ratio, and peak pulse discharge current control the current shared among parallel circuits. These parameters also determine the extent of the run time increase of …

Salmon At River's End: The Role Of The Estuary In The Decline And Recovery Of Columbia River Salmon, Daniel L. Bottom, Charles A. Simenstad, Jennifer Burke, Antonio M. Baptista, David A. Jay, Kim K. Jone, Edmundo Casillas, Michael H. Schiewe

Civil and Environmental Engineering Faculty Publications and Presentations

The continued decline of Columbia River salmon (Oncorhynchus spp.) populations has long focused concerns on habitat changes upriver, particularly the effects of large hydroelectric dams. Increasing evidence that ocean conditions strongly influence salmon production, however, has raised questions about the importance of the estuarine environment to salmon and whether the hydropower system has affected estuarine-rearing habitats. In response to Northwest Power Planning Council recommendations, we initiated a review of what is known about the effects of the hydroelectric system on the hydrology, habitats, and ecology of the Columbia River estuary. Our goal was to develop recommendations for improving estuarine conditions …

Estimation Of Columbia River Virgin Flow: 1879 To 1928, Pradeep K. Naik, David A. Jay

Civil and Environmental Engineering Faculty Publications and Presentations

The Columbia River has historically been a major source of economic activity for the Pacific Northwest, and is one of the more heavily modified rivers in the United States today. Understanding human and climate-induced changes in its hydrologic properties is, therefore, a topic of considerable interest. Long streamflow records are essential to determining how runoff has changed over time. Daily streamflow records of the Columbia River at The Dalles dates back to June 1978. However, the observed daily flow does not alone provide enough information to understand or separate anthropogenic and climate effects. It is necessary also to have an …

Measuring The Impacts Of Speed Reduction Technologies: Evaluation Of Dynamic Advanced Curve Warning System, Christopher Monsere, Casey Nolan, Robert Bertini, Edward Anderson, Tarek El-Seoud

Civil and Environmental Engineering Faculty Publications and Presentations

This paper presents the results of a quantitative and qualitative evaluation of a dynamic curve warning System deployed at one site on Interstate 5 in Oregon. On a dynamic message sign, the System displays messages directed to drivers on the basis of the observed speed of approaching vehicles. For the evaluation, three measures of effectiveness were selected: (a) the change in mean speed for passenger cars and commercial vehicles, (b) the change in the speed distribution for both passenger cars and trucks, and (c) public response to the sign. Speed samples were taken of vehicles with a laser ranging and …

Using Custom Transportation Data Collection Software With Handheld Computers For Education, Research, And Practice, Robert Bertini, Christopher Monsere, Andrew Byrd, Michael Rose, Tarek El-Seoud

Civil and Environmental Engineering Faculty Publications and Presentations

In an effort to facilitate data collection for research, give students first-hand experience collecting data for course projects, and generate interest in the transportation field through outreach, the Intelligent Transportation Systems Laboratory of Portland State University, Oregon, has developed custom data collection software for handheld computers using the Palm OS platform. The software is designed to export the collected data to desktop computers in common file formats suitable for analysis in spreadsheet and geographic information systems applications. Data collection problems addressed include recording position over time, recording geographic location of features, and performing cumulative vehicle or pedestrian counts.

Biofiltration For Treatment Of Gas-Phase Voc Mixtures, Bing Qi

LSU Doctoral Dissertations

Biological processes are increasingly used for treatment of air streams contaminated by biodegradable volatile organic compounds (VOCs). The research described in this dissertation involves systematic investigation of various facets of applying biological processes dominated by fungi to remove mixtures of VOCs representative of emissions from paint application and manufacturing. Screening studies were first conducted to assess the ability of multiple fungal species to degrade various industrially important VOCs. In the following phases of the research, studies were conducted to evaluate performance of laboratory-scale bioreactors inoculated with fungi for treatment of mixtures of VOCs representative of emissions from paint spray booths …

Perceived Importance Of National Occupational Cadd Skill Standards Among Faculty Of Nait Accredited Institutions, Ronald Shava

Dissertations and Theses @ UNI

This study presents a descriptive survey that examined the importance and relevance of National Occupational CARD Skills based on the perceptions of faculty teaching at National Association of Industrial Technology (NAIT) accredited institutions. The major goal of the study was to determine what National Occupational CADD Skill Standards are relevant and important to faculty teaching CARD courses. The study was also designed to determine ratings of the perceived importance and relevance of National Occupational CADD Skill Standards by faculty teaching CADD courses at NAIT accredited institutions based on their area of specialization, professional ranking, and teaching experience. This study provided …

Inventory Simulation And Optimization Using System Dynamics, Structural Modeling Equations And Genetic Algorithms In The Drivetrain Division Of An Automotive Manufacturer, Marco Sisfontes-Monge

Dissertations and Theses @ UNI

Strategic planning and control are among the most critical activities that modern enterprises require to succeed in the global economy. This research is an original study that investigated the combination of tools and methodologies in order to apply them to a midwestern tractor manufacturer. The current study identified the constraints applicable to a polishing line in the Drivetrain Division of a major tractor manufacturer interested in exploring alternative techniques to improve its worldwide manufacturing operations.

The specific questions that this project tried to respond are stated as follows:

1. What were the most important variables that affected inventory levels of an …

Physical Simulations In Classroom As A Pedagogical Tool For Enhancing Manufacturing Instruction In Engineering Technology Programs, Alok K. Verma, Han P. Bao, Anand Ghadmode, Swanand Dhayagude

Engineering Technology Faculty Publications

Lean is a powerful philosophy that advocates minimization of waste within an organization. The adoption of Lean Manufacturing philosophy by major manufacturers has created a demand for qualified personnel in this area. Higher education is not far behind in incorporating this philosophy into their curriculum. A number of universities have started offering both graduate and undergraduate courses in Lean Manufacturing. Physical simulations are often an integral part of these courses. Simulation based Lean enterprise concepts have been introduced in an undergraduate course in mechanical engineering technology program at Old Dominion University. Results show increased student participation and better understanding of …

Lessons Learned And Best Practices For Using An Analytic Strategy Approach For The Creation Of Virtual Laboratories For Distance Learning In Engineering Technology, Anthony W. Dean, Carol L. Considine, Gary R. Crossman

Engineering Technology Faculty Publications

This paper describes the use of an Analytic Strategy Approach used in the development of a Virtual Automation and Controls Lab in the Mechanical Engineering Technology Program of the Engineering Technology Department at Old Dominion University. This paper looks at the three phases, as applied to the development of a virtual lab using an analytic strategy design:

(1) Formulation of the quantitative and qualitative approach to assist in decision process,

(2) Quantitative and qualitative analysis of the decision alternatives - within the decision context,

(3) Interpretation of the analysis results and implications for decision.

Privatization Initiatives: A Source For Engineering Economy Case Studies, Paul Kauffmann, Tarek Abdel-Salam, Keith Williamson, Carol L. Considine

Engineering Technology Faculty Publications

A case study method which reviews the basic structure of the circular A-76 privatization decision model is discussed. It highlights the possibilities for development of case studies that can challenge student teams to apply engineering economy tools while developing skills in a range of circular areas that are important to undergraduate engineering education and career success in engineering practice. Beyond building quantitative and qualitative business analysis skills, engineering economy cases can enhance student skills in other topical areas such as technical presentations, and report writing. The privatization initiatives and related decision models can also enhance human relations oriented skills in …

Solar-Based Single-Stage High-Efficiency Grid-Connected Inverter, Feng Tian

Electronic Theses and Dissertations

Renewable energy source plays an important role in the energy cogeneration and distribution. Traditional solar-based inverter system is two stages in cascaded, which has a simpler controller but low efficiency. A new solar-based single-stage grid-connected inverter system can achieve higher efficiency by reducing the power semiconductor switching loss and output stable and synchronized sinusoid current into the utility grid. Controlled by the digital signal processor, the inverter can also draw maximum power from the solar array, thereby maximizing the utilization of the solar array. In Chapter 1, a comparison between the traditional two-stage inverter and the single-stage inverter is made. …

Evolution Of Lamellar Structures In Al-Ag Alloys, Sephalika Senapati

Electronic Theses and Dissertations

In the present study, the formation and the evolution of lamellar structures in different Al-Ag alloys were investigated by transmission electron microscopy (TEM). Plates of the hexagonal [gamma] phase form semi-coherently on the {111} planes of the face centered cubic lattice of the alloy after the formation of Guinier-Preston zones. Guinier-Preston zones are metastable coherent preprecipitates which are silver rich in the aluminum-rich Al-Ag alloys. The decomposition of aluminum rich Al-Ag alloys, particularly the sequence of the later stages of precipitate formation was studied. With scanning electron microscopy and high-resolution transmission electron microscopy the development of the [gamma] phase was …

Mechanical Properties Of The Intervertebral Disc As An Estimator Of Postmortem Interval, Jennifer Noelle Jackson

Electronic Theses and Dissertations

Currently, forensic scientists are only able to determine time since death (or postmortem interval) up to the first 60 hours. This is based largely on insect activity. Herein, it is proposed to use the degradation of the intervertebral disc (IVD) after death to determine a relationship between the mechanical properties of cadaveric tissue and time since death in order to extend the 60-hour window. To that end, 1 fresh human spine and 6 pig spines were each separated into sections (6 human and 48 pig), with each section having one intact disc. The sections were buried, unearthed, and cleaned, leaving …

Diffraction Studies Of Deformation In Shape Memory Alloys And Selected Engineering Components, Chandrasen Rathod

Electronic Theses and Dissertations

Deformation phenomena in shape memory alloys involve stress-, temperature-induced phase transformations and crystallographic variant conversion or reorientation, equivalent to a twinning operation. In near equiatomic NiTi, Ti rich compositions can exist near room temperature as a monoclinic B19' martensitic phase, which when deformed undergoes twinning resulting in strains as large as 8%. Upon heating, the martensite transforms to a cubic B2 austenitic phase, thereby recovering the strain and exhibiting the shape memory effect. Ni rich compositions on the other hand can exist near room temperature in the austenitic phase and undergo a reversible martensitic transformation on application of stress. Associated …

Modeling, Simulation And Analysis Of Multi-Barge Flotillas Impacting Bridge Piers, Peng Yuan

University of Kentucky Doctoral Dissertations

The current design code governing bridge structure resistance to vessel impact loads in the U.S. is the American Association of State Highway and Transportation Officials' (AASHTO) Guide Specification and Commentary for Vessel Collision Design of Highway Bridges. The code stipulated method, based on Meir-Dornberg's equivalent static load method, is usually not warranted because of insufficient data on the impact load histories and wide scatter of the impact force values. The AASHTO load equations ignore certain fundamental factors that affect the determination of impact forces and bridge dynamic responses. Some examples of factors that are omitted during standard impact force …

The Effect Of Colloidal Stability On The Heat Transfer Characteristics Of Nanosilica Dispersed Fluids, Manoj Venkataraman

Electronic Theses and Dissertations

Addition of nano particles to cooling fluids has shown marked improvement in the heat transfer capabilities. Nanofluids, liquids that contain dispersed nanoparticles, are an emerging class of fluids that have great potential in many applications. There is a need to understand the fundamental behavior of nano dispersed particles with respect to their agglomeration characteristics and how it relates to the heat transfer capability. Such an understanding is important for the development and commercialization of nanofluids. In this work, the stability of nano particles was studied by measuring the zeta potential of colloidal particles, particle concentration and size. Two different sizes …

Synthesis And Characterization Of Nanocrystalline Hydroxyapatite Powder; And The Effects Of Oxide-Based Sintering Additives On Tricalcium Phosphate, Himesh A. Bhatt

Electronic Theses and Dissertations

Calcium phosphate (CP) materials have been used extensively for bone replacement and augmentation due to their similarity to the mineral component of bone. In addition to being non-toxic, they are biocompatible, not recognized as foreign materials in vivo, and most importantly, exhibit osteoconductive behavior, being able to help in bone formation during healing. CPs form an intimate physicochemical bond with the host tissue, termed osseointegration. However the main limitation of calcium phosphates is their inherent brittle nature and poor mechanical performance under complex stress states. As a result, these materials have been used clinically only in non-load-bearing applications, primarily as …

Solution Of Electromagnetic Scattering Parameters And Radiation Patterns Of Arbitrary Body Of Revolution Radiators, Wendell Brokaw

Electronic Theses and Dissertations

A novel full wave analysis method to determine the scattering parameters and the radiation field intensities of arbitrary Body of Revolution (BOR) radiators consisting of impenetrable media is explored through derived components of modal analysis and the method of moments (MoM). Modal excitation is utilized to excite the structural feed; allowing for a more accurate measure of the scattering parameters of the total structure as opposed to the use of external excitation sources. The derivation of the mode matching method introduces a novel approach to achieving a frequency independent coupling matrix that will reduce the computational requirements for iterations utilized …

Attainable Compressive Strength Of Pervious Concrete Paving Systems, Ann Marie Mulligan

Electronic Theses and Dissertations

The pervious concrete system and its corresponding strength are as important as its permeability characteristics. The strength of the system not only relies on the compressive strength of the pervious concrete but also on the strength of the soil beneath it for support. Previous studies indicate that pervious concrete has lower compressive strength capabilities than conventional concrete and will only support light traffic loadings. This thesis investigated prior studies on the compressive strength on pervious concrete as it relates to water-cement ratio, aggregate-cement ratio, aggregate size, and compaction and compare those results with results obtained in laboratory experiments conducted on …

Real-Time Realistic Rendering And High Dynamic Range Image Display And Compression, Ruifeng Xu

Electronic Theses and Dissertations

This dissertation focuses on the many issues that arise from the visual rendering problem. Of primary consideration is light transport simulation, which is known to be computationally expensive. Monte Carlo methods represent a simple and general class of algorithms often used for light transport computation. Unfortunately, the images resulting from Monte Carlo approaches generally suffer from visually unacceptable noise artifacts. The result of any light transport simulation is, by its very nature, an image of high dynamic range (HDR). This leads to the issues of the display of such images on conventional low dynamic range devices and the development of …

A Methodology For Minimizing The Oscillations In Supply Chains Using System Dynamics And Genetic Algorithms, Ramamoorthy C.V.V. Lakkoju

Electronic Theses and Dissertations

Supply Chain Management (SCM) is a critically significant strategy that enterprises depend on to meet challenges that they face because of highly competitive and dynamic business environments of today. Supply chain management involves the entire network of processes from procurement of raw materials/services/technologies to manufacturing or servicing intermediate products/services to converting them into final products or services and then distributing and retailing them till they reach final customers. A supply chain network by nature is a large and complex, engineering and management system. Oscillations occurring in a supply chain because of internal and/or external influences and measures to be taken …

Surface Reconstruction From Medical Imaging For Use In A Computer-Aided Design (Cad) Environment, Gregory M. Sturgeon

Masters Theses

A method was developed to create Computer-Aided-Design (CAD) models for bones of the human body utilizing medical imaging data. The human hand was chosen as the subject of the research.

Computed Tomography (CT) imaging was chosen to provide a volumetric data set. This data set was visualized through an isosurfacing technique utilizing the marching cubes algorithm. The original CT data set contained slices that were not aligned with the natural orientation or long axis of the bones. Transformation matrices and linear interpolations were used to generate a data set of slices oriented along the natural axis of the bones.

Contours …

Stabilizing Inter-Domain Routing In The Internet, Yu Chen, Ajoy K. Datta, Sebastien Tixeuil

Mechanical Engineering Faculty Research

This paper reports the first self-stabilizing Border Gateway Protocol (BGP). BGP is the standard inter-domain routing protocol in the Internet. Self-stabilization is a technique to tolerate arbitrary transient faults.

The routing instability in the Internet can occur due to errors in configuring the routing data structures, the routing policies, transient physical and data link problems, software bugs, and memory corruption. This instability can increase the network latency, slow down the convergence of the routing data structures, and can also cause the partitioning of networks. Most of the previous studies concentrated on routing policies to achieve the convergence of BGP while …

Application Of Meshless Methods For Thermal Analysis, Darrell Pepper, Bozidar Sarler

Mechanical Engineering Faculty Research

Many numerical and analytical schemes exist for solving heat transfer problems. The meshless method is a particularly attractive method that is receiving attention in the engineering and scientific modeling communities. The meshless method is simple, accurate, and requires no polygonalisation. In this study, we focus on the application of meshless methods using radial basis functions (RBFs) — which are simple to implement — for thermal problems. Radial basis functions are the natural generalization of univariate polynomial splines to a multivariate setting that work for arbitrary geometry with high dimensions. RBF functions depend only on the distance from some center point. …

University Of Nevada, Las Vegas Transmutation Research Program: Annual Report Academic Year 2004-2005, Anthony Hechanova, Kathy Lauckner

Transmutation Research Program Reports (TRP)

It is my pleasure to present the UNLV Transmutation Research Program’s fourth annual report that highlights the academic year 2004 – 2005. Supporting this document are the many technical reports and scientific papers that have been generated over the past three years.

In the fourth year of our program, we added 11 new research tasks and saw the conclusion of 8 of the initial 16 independent student research tasks started in 2001 and 2002. In all, the program has sponsored to their conclusion 28 M.S. and 2 Ph.D. degrees. The program supported 58 graduate students and 13 undergraduates in 6 …

Modeling, Fabrication, And Optimization Of Niobium Cavities, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

One of the key technologies for the deployment of accelerator driven transmutation systems is the accelerator itself. Elliptical superconducting niobium cavities are used to increase the efficiency of the high-power accelerators needed to support the transmutation mission.

One of the major sources of energy loss from a superconducting accelerator cavity is a process known as multiple impacting (or “multipacting”) of electrons. This phenomenon limits the maximum amount of energy and power that the niobium cavity can store. As a result, the maximum power available for accelerating the desired charge, as well as the overall performance of the accelerator is reduced. …

Corrosion Of Steel By Lead Bismuth Eutectic, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

There is an active international interest in lead-bismuth eutectic and similar liquid lead systems because of the relevance to the transmutation of nuclear waste, fast reactors, and spallation neutron sources.

Materials in these systems must be able to tolerate high neutron fluxes, high temperatures, and chemical corrosion. For lead bismuth eutectic (LBE) systems, there is an additional challenge because the corrosive behaviors of materials in LBE are not well understood. Most of the available information on LBE systems has come from the Russians, who have over 80 reactor-years experience with LBE coolant in their Alpha-class submarine reactors. The Russians found …

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials, Ajit K. Roy

Transmutation Sciences Materials (TRP)

The primary objective of this task was to evaluate the effects of environmental and mechanical parameters on environment induced degradations of candidate target structural materials for applications in spallation-neutron-target systems. The materials selected for evaluation and characterization were martensitic stainless steels including Alloys HT-9, EP-823, and 422.

Accelerator-driven transmutation systems involve bombarding a target material such as molten lead-bismuth-eutectic (LBE) by a proton beam, thereby producing neutrons. The molten LBE target will be contained in a subsystem structural container made of a suitable material such as Alloys HT-9, EP-823, and 422. During the transmutation process, the target structural material may …