Engineering Commons^™

Oxidation Of Titanium In Alpha-Calf Serum Solution, Ali Stait Ismailoglu

Masters Theses

Titanium and its alloys have been used extensively in orthopedic implants mainly because of its excellent biocompatibility. This biocompatibility is attributed to its surface oxide film (3-7 nm thickness) that forms immediately upon exposure of titanium to air. In the research, the oxidation of Ti-6Al-4V in alpha-calf serum solution was studied. Four different immersion times were tested. Characterization of surface topography and its chemical composition was examined using Atomic force microscopy (AFM), Fourier transform-infrared radiation (FT-IR), and X-ray photoelectron spectroscopy (XPS). The AFM results clearly show the gradual change that occurred in the samples topography which is associated with more-rounded …

Acoustic Wave Based Biosensor, Aditya A. Vijh

Masters Theses

Quartz Crystal Microbalances (QCMs) have been widely used for detection of various chemical and biological species in liquid media. In this work an improved binding of Protein A and IgG molecules on QCM biosensors by modifying the gold surface of the quartz crystal with an ultra thin polystyrene film followed by an acidic treatment has been reported. Protein A and IgG immobilizations on quartz crystals with the polystyrene film represented a 65% increase and a 40% increase respectively when compared to immobilization done directly onto the crystals. Atomic Force Microscopy (AFM) has been used to investigate and study the biomolecular …

Indentation Of A Square Elastomeric Thin Film By A Flat-Ended Cylindrical Punch In The Presence Of Long-Range Intersurface Forces, Bing Feng Ju, Kai-Tak Wan, Kuo Kang Liu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper reports an experimental study of the elastic deformation of a 200 μm thick microfabricated square membrane with sides ranging from 8.5 mm to 15 mm as indented by a fine cylindrical, flat-ended punch with diameter 500 μm in the presence of long-range intersurface forces. an apparatus was constructed to allow simultaneously measurements of the indenter displacement and the applied force. a number of interesting phenomena such as the "jump-into-contact" and the "pull-off" between the membrane and the moving cylinder were observed. a simple theoretical analysis using linear elasticity was adopted to fit the load-displacement curve (compliance) and thus …

Evaluating The Repair Of System-On-Chip (Soc) Using Connectivity, Minsu Choi, Nohpill Park, Vincenzo Piuri, Fabrizio Lombardi

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents a new model for analyzing the repairability of reconfigurable system-on-chip (RSoC) instrumentation with the repair process. It exploits the connectivity of the interconnected cores in which unreliability factors due to both neighboring cores and the interconnect structure are taken into account. Based on the connectivity, two RSoC repair scheduling strategies, Minimum Number of Interconnections First (I-MIN) and Minimum Number of Neighboring Cores First (C-MIN), are proposed. Two other scheduling strategies, Maximum Number of Interconnections First (I-MAX) and Maximum Number of Neighboring cores First (C-MAX), are also introduced and analyzed to further explore the impact of connectivity-based repair …

Pre-Impact Lower Extremity Posture And Brake Pedal Force Predict Foot And Ankle Forces During An Automobile Collision, Elizabeth C. Hardin, Anne Su, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

Background: The purpose of this study was to determine how a driver’s foot and ankle forces during a frontal vehicle collision depend on initial lower extremity posture and brake pedal force. Method of Approach: A 2D musculoskeletal model with seven segments and six right-side muscle groups was used. A simulation of a three-second braking task found 3647 sets of muscle activation levels that resulted in stable braking postures with realistic pedal force. These activation patterns were then used in impact simulations where vehicle deceleration was applied and driver movements and foot and ankle forces were simulated. Peak rearfoot ground reaction …

Safety Evaluation Of Left Turn Lane Line Width At Intersections With Opposing Left Turn Lanes, Aemal Khattak, Bhaven Naik, Vijay Kannan

Nebraska Department of Transportation: Research Reports

The objective of this research project was to evaluate the effectiveness of offset opposing left-turn lanes at signalized intersections in reducing the frequency and severity of left-turn related accidents. The Cities of Lincoln and Omaha offset opposing left-turns by widening leftturn lane lines in June 1999 at six intersections. The research team investigated traffic accident patterns between January 1994 and December 2002 at those six intersections by making comparisons with two control intersections (i.e. intersections at which left-turns were not offset by lane line widening) using a four-step research methodology. First, existing literature was reviewed to determine the extent and …

Bond Strength Of Self-Consolidating Concrete For Prestressed Concrete Applications, Christopher Y. Tuan, Amgad F. Girgis

Nebraska Department of Transportation: Research Reports

No abstract provided.

Cross-Layer Design Of A Dynamic Resource Allocation Control For The Next Multimedia Wireless Generation 1xev-Dv Systems, Mohamed Bourouha

Masters Theses

1xEV-DV has been proposed as one of the standards of the next MultimediaWire- less Generation (MWG) systems, which adopts new techniques to enhance wireless data Quality of Service (QoS). Despite the recent research efforts in mapping QoS pa- rameters cross the different layers, there is still no cross layer QoS design that focuses in providing QoS assurances in the 1xEV-DV. Moreover, many possible combinations of resource parameters have been specified in the current standard. However, there are no specifications about the dynamic resource allocation. In this thesis, a suite of Cross Layer Multiuser Diversity Modules are proposed. These modules include …

Bs News

Building Services Engineering

No abstract provided.

Microwave Pretreatment Of Corn Stover For Anaerobic Digestion, Abhishek D. Saxena

Masters Theses

Anaerobic digestion is one of the several technologies used for biomass conversion to electricity or heat. This thesis focused on microwave irradiation of corn stover as a pretreatment for anaerobic digestion, and studies its impact on methane production.

The first run comprised three sets of stover soaked overnight in water, dilute sulfuric acid and dilute acetic acid, and each treated to three different levels of microwave irradiation. The results indicated a high variability in the data of the water set, which showed that there was no clear impact of microwave pretreatment on methane production. The dilute sulfuric acid and dilute …

Neutron Multiplicity Measurements For The Afci Program Quarterly Progress Report September-December 2004, Denis Beller

Transmutation Sciences Physics (TRP)

The U.S. Advanced Fuel Cycle Initiative (AFCI) is a program to develop economic and environmental methods to reduce the impact of waste from commercial nuclear fuel cycles. One concept for near-complete destruction of waste isotopes from used nuclear fuel is accelerator driven transmutation. High-power accelerators would be used to produce high-energy charged particles, which then collide with heavy metal targets to create a cascade of neutrons. These neutrons then cause a nuclear chain reaction in subcritical systems. Fission neutrons then transmute fissile waste isotopes as well as other problematic isotopes such as technetium-99 and iodine-129. To design these systems, complex …

A Plan For Router Testing In Network-On-Chip, Zachariah Thomas Link

Open Access Master's Theses (through 2010)

This thesis presented a new method for testing routers and cores on Network-On-Chip (NoC) systems.It proposed a new algorithm for router testing that relies heavily on the reuse of the network infrastructure within an NoC. Possible wrapper architecture for the router was also presented. Combing the router and core wrapper into one wrapper can reduce the wrapper hardware and is important in the reuse of the network for router testing. Finally, an integrated algorithm for scheduling tests for routers and cores was presented. Simulations were run comparing results using this integrated algorithm to previous work based on boundary scan.

Advisor: …

Ab Initio Calculation Of Electronic And Optical Properties Of Beryllium Chalcogenides (Bes, Bese, And Bete) Under The Effect Of Pressure, Aisha Ali Saif Bannan Al-Kaabi

Theses

There are several methods for materials simulation. Ab initio or first principles methods are used to solve the quantum mechanical equation which govern the behavior of a system. Ab initio calculation of the optical and electronic properties of solids is fundamental in solid state physics. APW+lo is used to examine different properties of BeS, BeSe and BeTe. Beryllium compounds show different features in structure under different pressures, and they also show a phase transition from Zinc blende to Hexagonal transitions in II-VI semiconductors. Little is known about the ground state properties of Beryllium Chalcogenides. The aim of this work is …

Stress Corrosion Cracking Resistance Of Martensitic Stainless Steels For Transmutation Applications, Phani P. Gudipati

UNLV Theses, Dissertations, Professional Papers, and Capstones

The susceptibility of Alloy EP-823 to stress corrosion cracking has been evaluated using smooth and notched cylindrical specimens in neutral and acidic solutions at ambient and elevated temperatures using constant load and slow strain rate testing (SSR) techniques. C-ring and U-bend specimens have also been tested in the acidic solution. The effect of hydrogen on the cracking susceptibility has been evaluated under controlled cathodic potential. While no failures were observed with smooth specimens at constant load, the notched specimens showed failure. The SSR test results indicate that the true failure stress (o'_f), time to failure and ductility parameters …

Stress Corrosion Cracking And Hydrogen Embrittlement Of Martensitic Alloy Ep-823, Mohammad K. Hossain

UNLV Theses, Dissertations, Professional Papers, and Capstones

This investigation is focused on the evaluation of stress corrosion cracking (SCC), localized corrosion, and hydrogen embrittlement (HE) susceptibility of martensitic Alloy EP-823 in neutral and acidic solutions at ambient and elevated temperatures. While no failures were observed in smooth specimens in the neutral solution, failures were noticed in the 90°C acidic solution at constant-load (CL) leading to a threshold stress (O'_th) of 102 ksi. The presence of a notch reduced the O'_th value to 91 ksi in a similar environment. The ductility (%El and %RA), time-to-failure (TTF), and true failure stress (O'_r) were gradually …

Cfd Analysis Of 3-D Thermalhydraulics Flow Effects On Wall Concentration Gradient Profiles For Lbe Loop Fittings, Narain Armbya

UNLV Theses, Dissertations, Professional Papers, and Capstones

The objective of the thesis is to study the effects of thermalhydraulics flows on the wall concentration gradient profiles in LBE loop fittings. To that end detailed models of the fittings have been constructed to study these effects. These fittings include sudden expansion, sudden contraction, t-joint and elbow. The typical flow rates chosen for these simulations are typical of design criteria chosen for the loop with Reynolds numbers expected around 200,000 and the usual axial temperature profiles which are being characterized in the DELTA loop at LANL. STAR-CD is the simulation package used to make these predictions, which include detailed …

Analysis And Control Of A Buck Dc-Dc Converter Operating With Constant Power Load In Sea And Undersea Vehicles, Claudio Rivetta, Ali Emadi, Geoffrey A. Williamson, Ranjit Jayabalan, Babak Fahimi

Electrical and Computer Engineering Faculty Research & Creative Works

Power electronics based zonal DC power distribution systems are being considered for sea and undersea vehicles. the stability of the DC power electronics-based power distribution systems is a significant design consideration because of the potential for negative impedance induced instabilities. in this paper, dynamic properties and control of a buck converter feeding a downstream DC-DC converter are studied. the controller in this system combines an instantaneous current feedback loop using hysteresis with a proportional-integral algorithm to regulate the output voltage of the converter. based on a large-signal averaged model of the converter, the stability-in-large around the operation point is presented. …

Algoritmo Genético Para Calibração Automática De Um Simulador De Tráfego Em Rodovias De Pista Simples, C. Y. Egami, J. R. Setti, Laurence Rilett

Department of Civil and Environmental Engineering: Faculty Publications

Este trabalho relata o desenvolvimento de um sistema automático para calibração do modelo de simulação de tráfego em rodovias de pista simples TRARR, baseado em um algoritmo genético. O processo de calibração consiste em procurar valores para alguns parâmetros selecionados do simulador, de tal modo que a diferença entre as correntes de tráfego simuladas e as observadas em campo sejam minimizadas. Os parâmetros escolhidos para a calibração estão relacionados principalmente ao comportamento dos motoristas e, por isso, de difícil calibração. As diferenças entre a simulação e o fluxo real foram determinadas em termos de duas medidas de desempenho: a velocidade …

Efficient Algorithm For Computing Einstein Integrals, Junke Guo, Pierre Y. Julien

Department of Civil and Environmental Engineering: Faculty Publications

Analytical approximations to Einstein integrals are proposed. The approximations represented by two fast-converging series are valid for all values of their arguments. Accordingly, the algorithm can be easily incorporated into professional software like HEC-RAS or HEC-6 with minimum computational effort.

Rf Cmos Receiver Front-End Using A Reflex Amplifier, Radovan Kuzet

Theses and Dissertations - UTB/UTPA

A concept for an RF-CMOS receiver with reflex topology is developed and tested, using OrCad as the primary design and simulation tool. The main idea of the reflex topology is to reuse a Low Noise Amplifier (LNA) stage in the circuit and thus eliminate one high power consumption stage. A Gilbert cell is used for down conversion, with the benefit of low noise and low power while maintaining gain. A set of passive diplexers allows reuse of the LNA at the RF and IF. The complete circuit was simulated using 0.18 micron and 0.5 micron AMI technology. Parameters for the …

A Template-Based Conceptual Modeling Infrastructure For Simulation Of Physical Security Systems, Ashu Guru, Paul Savory

Department of Industrial and Management Systems Engineering: Faculty Publications

Although simulation is one of the most innovative and cost-effective tools for modeling and analyzing a system, simulation studies often fail to provide any useful results. One reason is attributed to the fact that model formulation depends on the skills of the analyst. This paper describes a research to develop a conceptual modeling infrastructure to assist a simulation analyst in specifying components for studying physical security systems. The modeling framework has been programmed as an internet-based web application. Using the application, the successful development and implementation of a physical security simulation model will be aided by a defined scientific methodology …

A Study Of Umts Turbo Codes Across Space Time Spreading Channel With The Case Of M = 1 And M = 2, Ibrahim S. Raad, Peter Vial, Tadeusz A. Wysocki

Department of Electrical and Computer Engineering: Faculty Publications (to 2015)

The study presented in this paper is that of Universal Mobile Telecommunications Systems (UMTS) Turbo Codes across Space Time Spreading channel with one transmitter antenna, one receiver (m = 1) and two transmitter antennas and one receiver (m = 2) to see to what extent the bit error rate (BER) can be improved. Using the Max-log decoding algorithm and 12 iterations it is shown in the simulation results that an extra 5 dB is achievable.

Load-Balanced Route Discovery For Mobile Ad Hoc Networks, Mehran Abolhasan, Justin Lipman, Tadeusz A. Wysocki

Department of Electrical and Computer Engineering: Faculty Publications (to 2015)

This paper presents Flow-Aware Routing Protocol (FARP), a new routing strategy designed to improve load balancing and scalability in mobile ad hoc networks. FARP is a hop-by-hop routing protocol, which introduces a flow-aware route discovery strategy to reduce the number of control overheads propagating through the network and distributes the flow of data through least congested nodes to balance the network traffic. FARP was implemented in Glomosim and compared with AODV. To investigate the load distribution capability of FARP new performance metrics were introduced to measure the data packet flow distribution capability of the each routing protocol. The simulation results …

Thermodynamic Analysis Of Separation Systems, Yaşar Demirel

Papers in Thermal Mechanics

Separation systems mainly involve interfacial mass and heat transfer as well as mixing. Distillation is a major separation system by means of heat supplied from a higher temperature level at the reboiler and rejected in the condenser at a lower temperature level. Therefore, it resembles a heat engine producing a separation work with a rather low efficiency. Lost work (energy) in separation systems is due to irreversible processes of heat, mass transfer, and mixing, and is directly related to entropy production according to the Gouy-Stodola principle. In many separation systems of absorption, desorption, extraction, and membrane separation, the major irreversibility …

Attenuation Of Ultrasonic Waves In Rolled Metals, Liyong Yang, Joseph A. Turner

Nebraska Center for Materials and Nanoscience: Faculty Publications

Scattering of ultrasonic waves in polycrystals with texture is studied in this article. The attenuations of the three wave modes are determined as a function of dimensionless frequency and propagation direction, respectively, for given orientation distribution coefficients (ODCs). The calculation is done in the case of a statistically orthorhombic sample made up of cubic crystallites. The wave propagation and scattering model is formulated by the Dyson equation using an anisotropic Green’s function approach.Within the limits of the first-order smoothing approximation, the Dyson equation is solved in the spatial Fourier transform domain. The results presented are shown to be directional dependent, …

Decadal-Scale Changes In West Coast Shelf Internal Tides (The Tides, They Are A Changin'), David A. Jay, Thomas A. Chisholm, A. Krause, K. Leffler

Civil and Environmental Engineering Faculty Publications and Presentations

The National Science Foundation (NSF) Co-OP (Coastal Ocean Program) Project RISE (River-Influenced Shelf Ecosystems) seeks to understand how primary and secondary productivity are enhanced by large river plumes in upwelling regions, using the Columbia River plume as a case study. Columbia River plume waters are rich in silicate and iron, but relatively depleted in nitrate. Mixing of nitrate-rich upwelled water with the plume is, therefore, important to plume primary production. Large internal tidal currents cause part of the necessary mixing. Accordingly, any long-term changes in these internal tides could impact productivity. Because no decadal-scale current observations are available to evaluate …

Environment Assisted Cracking Of Target Structural Materials Under Different Loading Conditions, Venkataramakrishnan Selvaraj

UNLV Theses, Dissertations, Professional Papers, and Capstones

Martensitic Alloy HT-9 has been tested for its evaluation of stress corrosion cracking resistance in neutral and acidic solutions at ambient and elevated temperatures incorporating smooth and notched cylindrical specimens under constant load and slow strain rate (SSR) conditions. C-ring and U-bend specimens have also been tested for stress corrosion cracking evaluation in the acidic solution. The role of hydrogen on the cracking tendency has been evaluated by cathodic applied potential.

The results of constant load testing enabled the determination of the threshold stress for stress corrosion cracking in susceptible environments. The magnitudes of ductility parameters were reduced with increasing …

Trade Space Analysis Of Antenna Array Architecture Using System Modeling Tools, Eugene Johnson

Theses and Dissertations

This trade study has two objectives. The first provides a trade space analysis of differing array architectures and associated radio frequency components using system-modeling tools. The second objective develops system modeling tools aiding similar analysis by other users. These objectives were accomplished by evaluating a selected group of output parameters to include overall system cost, mass, and power consumption, as well as the minimum detectable input level, system spurious free dynamic range, and selected beam spoilage parameters caused by the use of discrete phase shifters. A fixed number of designs were evaluated using simulation. The evaluation process examined input parameter …

Afci Quarterly Input – Unlv October Through December, 2004, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support. Management and program support highlights are the following: the UNLV TRP hosted the Eighth Annual IAEA Actinide and Fission Product Partitioning & Transmutation Information Exchange Meeting (Nov. 9 – 11). 120 people from 22 countries …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry, Morphology, And Surface Preparation: Quarterly Report (October-December 2004), Allen L. Johnson, John Farley, Dale L. Perry

Transmutation Sciences Materials (TRP)

This project has four components:

(1) the fabrication of a materials test apparatus with unique capabilities,

(2) comparative studies of steel corrosion under gas phase conditions comparable to the Lead Bismuth Eutectic (LBE) oxygen control conditions,

(3) isotope labeling studies, and

(4) collaborative efforts with other workers in the field.